Measurement of the Charge Collection Efficiency after Heavy Non-Uniform Irradiation in BaBar Silicon Detectors
S. Bettarini, M. Bondioli, L. Bosisio, G. Calderini, C. Campagnari, S. Dittongo, F. Forti, M. A. Giorgi, G. Marchiori, G. Rizzo
备注：
7 pages, 13 figures. Presented at the 2004 IEEE Nuclear Science Symposium, October 18-21, Rome, Italy. Accepted for publication by IEEE Transactions on Nuclear Science
We have investigated the depletion voltage changes, the leakage current increase and the charge collection efficiency of a silicon microstrip detector identical to those used in the inner layers of the BaBar Silicon Vertex Tracker (SVT) after heavy non-uniform irradiation. A full SVT module with the front-end electronics connected has been irradiated with a 0.9 GeV electron beam up to a peak fluence of 3.5 x 10^14 e^-/cm^2, well beyond the level causing substrate type inversion. We irradiated one of the two sensors composing the module with a non-uniform profile with sigma=1.4 mm that simulates the conditions encountered in the BaBar experiment by the modules intersecting the horizontal machine plane. The position dependence of the charge collection properties and the depletion voltage have been investigated in detail using a 1060 nm LED and an innovative measuring technique based only on the digital output of the chip.
The BABAR Silicon Vertex Tracker (SVT) is a five-layer double-sided silicon detector designed to provide precise measurements of the position and direction of primary tracks, and to fully reconstruct low-momentum tracks produced in e+e- collisions at the PEP-II asymmetric collider at Stanford Linear Accelerator Center. This paper describes the design, implementation, performance, and validation of the local alignment procedure used to determine the relative positions and orientations of the 340 SVT wafers. This procedure uses a tuned mix of in-situ experimental data and complementary lab-bench…
The radiation hardness of the AToM chips of the BaBar Silicon Vertex Tracker has been investigated by means of irradiations with photons from a 60Co source and 0.9 GeV electrons. The increase in noise and the decrease in gain of the amplifier have been measured as a function of the applied capacitive load and the absorbed dose. Different beam intensities have been used to study the effect of different dose rates to the AToM radiation damage. The chip digital functionalities have been tested up to a dose of 5.5 Mrads for the 60Co photons and 9 Mrads for the 0.9 GeV electrons. In addition a pede…
To prevent excessive radiation damage to its Silicon Vertex Tracker, the BaBar experiment at SLAC uses a radiation monitoring and protection system that triggers a beam abort whenever radiation levels are anomalously high. The existing system, which employs large area Si PIN diodes as radiation sensors, has become increasingly difficult to operate due to radiation damage. We have studied CVD diamond sensors as a potential alternative for these silicon sensors. Two diamond sensors have been routinely used since their installation in the Vertex Tracker in August 2002. The experience with these s…
The report contains various aspects of radiation damage in silicon detectors subjected to high intensity hadron and electromagnetic irradiation. It focuses on improvements for the foreseen LHC applications, employing oxygenation of silicon wafers during detector processing (result from CERN-RD48). An updated survey on hadron induced damage is given in the first article. Several improvements are outlined especially with respect to antiannealing problems associated with detector storage during LHC maintenance periods. Open questions are outlined in the final section, among which are a full under…
Stability of Charge Collection Efficiency and Time Resolution in a Novel Ultra-fast Graphene-Optimized Silicon Carbide Detector Under X-ray Irradiation
Institute of High Energy Physics, Chinese Academy of Sciences（中国科学院高能物理研究所）；Liaoning University（辽宁大学）；Qufu Normal University（曲阜师范大学）；Jilin University（吉林大学）
The Mu2e calorimeter is composed of 1400 un-doped CsI crystals, coupled to large area UV extended Silicon Photomultipliers (SiPMs), arranged in two annular disks. This calorimeter has to provide precise information on energy, timing and position resolutions. It should also be fast enough to handle the high rate background and it must operate and survive in the high radiation environment. Simulation studies estimated that, in the highest irradiated regions, each photo-sensor will absorb a dose of 20 krad and will be exposed to a neutron fluency of 5.5x10^11 n_(1MeV)/cm^2 in three years of runni…
Silicon detectors in particle physics experiments at the new accelerators or in space missions for physics goals will be exposed to extreme radiation conditions. The principal obstacles to long-term operation in these environments are the changes in detector parameters, consequence of the modifications in material properties after irradiation. The phenomenological model developed in the present paper is able to explain quantitatively, without free parameters, the production of primary defects in silicon after particle irradiation and their evolution toward equilibrium, for a large range of gen…
Influence of the prolonged irradiation by fission products of 252Cf radionuclide on the operational parameters of silicon-lithium Si(Li) p-i-n detectors, Si surface barrier detectors and Si planar p+n detector was investigated. The obtained results revealed a linear shift of the fission fragment peaks positions towards the lower energies with increase of the irradiation dose for all investigated detectors. The rate of the peaks shift was found to depend strongly on the detector type and the strength of the electric field in the detectors active region, but not on the temperature of irradiation…
We have investigated the effects of X-ray irradiation to doses of 0, 200 Gy, 20 kGy, 2 MGy, and 20 MGy on the Hamamatsu silicon-photomultiplier (SiPM) S10362-11-050C. The SiPMs were irradiated without applied bias voltage. From current-voltage, capacitance/conductance-voltage, -frequency, pulse-shape, and pulse-area measurements, the SiPM characteristics below and above breakdown voltage were determined. Significant changes of some SiPM parameters are observed. Up to a dose of 20 kGy the performance of the SiPMs is hardly affected by X-ray radiation damage. For doses of 2 and 20 MGy the SiPMs …
Silicon photomultipliers (SiPMs) have become popular light conversion devices in recent years due to their low bias voltage and sensitivity to wavelengths emitted from common scintillating materials. These properties make them particularly attractive for resource-constrained missions such as space-based detector applications. However the space radiation environment is known to be particularly harsh on semiconductor devices, where high particle fluences can degrade performance over time. The radiation hardness of a particular SiPM, manufactured by ON Semiconductor (formally SensL), has yet to b…
The principal obstacle to long-time operation of silicon detectors at the highest energies in the next generation of experiments arises from bulk displacement damage which causes significant degradation of their macroscopic properties. The analysis of the behaviour of silicon detectors after irradiation conduces to a good or reasonable agreement between theoretical calculations and experimental data for the time evolution of the leakage current and effective carrier concentration after lepton and gamma irradiation and large discrepancies after hadron irradiation and this in conditions where a …
Detectors proposed for the International Linear Collider (ILC) incorporate a tungsten sampling calorimeter (`BeamCal') intended to reconstruct showers of electrons, positrons and photons that emerge from the interaction point of the collider with angles between 5 and 50 milliradians. For the innermost radius of this calorimeter, radiation doses at shower-max are expected to reach 100 MRad per year, primarily due to minimum-ionizing electrons and positrons that arise in the induced electromagnetic showers of e+e- `beamstrahlung' pairs produced in the ILC beam-beam interaction. However, radiatio…
The response of n+p silicon strip sensors to electrons from a Sr-90 source was measured using a multi-channel read-out system with 25 ns sampling time. The measurements were performed over a period of several weeks, during which the operating conditions were varied. The sensors were fabricated by Hamamatsu Photonics K.K. on 200 micrometer thick float-zone and magnetic-Czochralski silicon. Their pitch was 80 micrometer, and both p-stop and p-spray isolation of the n+ strips were studied. The electrons from the Sr-90 source were collimated to a spot with a full-width-at-half-maximum of 2 mm at t…
Technological tests of Total Ionizing Dose effects are required not only for silicon particle sensors developed in high energy physics experiments, but also for electronic devices and semiconductor elements used in commercial, automotive and space applications. Using x-ray irradiators, these technological tests and studies can be performed not only in facilities explicitly built for this mission, but also in medical or biological research facilities when some minima requirements are satisfied. Generally this irradiation can be performed without interfering with the medical and biological activ…
In this contribution, the production of defects in radiation fields and their evolution toward equilibrium in silicon for detector uses has been modelled. In the quantitative model developed, the generation rate of primary defects is calculated starting from the projectile - silicon interaction and from recoil energy redistribution in the lattice. Vacancy-interstitial annihilation, interstitial migration to sinks, divacancy and vacancy-impurity complex (VP, VO, V2O, CiOi and CiCs) formation are considered. The results of the model support the experimental available data. The correlation betwee…
Silicon Photomultipliers with cell-pitch ranging from 12 $μ$m to 20 $μ$m were tested against neutron irradiation at moderate fluences to study their performance for calorimetric applications. The photosensors were developed by FBK employing the RGB-HD technology. We performed irradiation tests up to $2 \times 10^{11}$ n/cm$^2$ (1 MeV eq.) at the INFN-LNL Irradiation Test facility. The SiPMs were characterized on-site (dark current and photoelectron response) during and after irradiations at different fluences. The irradiated SiPMs were installed in the ENUBET compact calorimetric modules and c…
In the future ATLAS Inner Tracker, each silicon strip module will be equipped with a switch able to separate the high voltage supply from the sensor in case the latter becomes faulty. The switch, placed in between the HV supply and the sensor, needs to sustain a high voltage in its OFF state, to offer a low resistance path for the sensor leakage current in the ON state, and be radiation hard up to 1.2e15 neq/cm2 along with other requirements. While GaN JFETs have been selected as suitable rad-hard switch, a silicon vertical HV-JFET was developed by Brookhaven National Laboratory as an alternat…
The collection of charge carriers generated in p+n strip sensors close to the Si-SiO2 interface before and after 1 MGy of X-ray irradiation has been investigated using the transient current technique with sub-nanosecond focused light pulses of 660 nm wavelength, which has an absorption length of 3.5 um in silicon at room temperature. The paper describes the measurement and analysis techniques used to determine the number of electrons and holes collected. Depending on biasing history, humidity and irradiation, incomplete collection of either electrons or holes is observed. The charge losses cha…
In-situ Radiation Damage Study of Silicon Carbide Detectors Subjected to Clinical Proton Beams
Marietta Blau Institute for Particle Physics, Austrian Academy of Sciences（玛丽塔·布劳粒子物理研究所，奥地利科学院）；Institute of Atomic and Subatomic Physics, TU Wien（维也纳工业大学原子与亚原子物理研究所）
We fabricated a readout ASIC with the fully depleted silicon-on-insulator (FD-SOI) technology for the pair-monitor. The pair-monitor is a silicon pixel device that measures the beam profile of the international linear collider. It utilizes the directional distribution of a large number of electron-positron pairs created by collision of bunches, and is required to tolerate radiation dose of about a few Mrad/year. The irradiation might cause the buried oxide layer of SOI to accumulate charges which interfere with intended functions. We thus performed extensive irradiation tests on the prototype …
Silicon photomultipliers (SiPMs) are highly-sensitive photodetectors emerging as the technology of choice for many applications, including large high-energy physics experiments where they often are exposed to high radiation fluences. In recent years, there has been an increasing interest in assessing the performance deterioration of such detectors after the irradiation with proton or neutron, with different fluence levels. In this work, samples of different FBK SiPM technologies, made with different manufacturing technologies, were irradiated at the INFN-LNS facility (Italy) with protons reach…
Radiation effects on surface and bulk properties of ATLAS18 silicon sensors under low- and high-dose gamma irradiation and annealing
Institute of Physics, Academy of Sciences of the Czech Republic（捷克科学院物理研究所）；Santa Cruz Institute for Particle Physics (SCIPP)（圣克鲁斯粒子物理研究所）；UJP Praha a.s.（UJP布拉格有限公司）；Experimental Particle Physics Department, Jožef Stefan Institute（约瑟夫斯特凡研究所实验粒子物理部）；Instituto de Microelectronica de Barcelona (IMB-CNM), CSIC（西班牙国家科学研究委员会巴塞罗那微电子研究所）；Institute of Particle and Nuclear Study, High Energy Accelerator Research Organization (KEK)（高能加速器研究机构粒子核研究部）；Physikalisches Institut, Albert-Ludwigs-Universität Freiburg（弗赖堡大学物理研究所）
For the high-luminosity phase of the Large Hadron Collider (HL-LHC), at the expected position of the innermost pixel detector layer of the CMS and ATLAS experiments, the estimated equivalent neutron fluence after 3000 fb$^{-1}$ is 2$\cdot$10$^{16}$ n$_{eq}$/cm$^2$, and the IEL (Ionizing Energy Loss) dose in the SiO$_2$ 12 MGy. The optimisation of the pixel sensors and the understanding of their performance as a function of fluence and dose makes a radiation damage model for TCAD simulations, which describes the available experimental data, highly desirable. The currently available bulk-damage …
Silicon avalanche photodiodes (APDs) are sensitive to operating temperature fluctuations and are also susceptible to radiation flux expected in satellite-based quantum experiments. We introduce a low power voltage adjusting mechanism to overcome the effects of in-orbit temperature fluctuations. We also present data on the performance of Si APDs after irradiation (gamma-ray and proton beam). Combined with an analysis of expected orbital irradiation, we propose that a Si APD in a 400 km equatorial orbit may operate beyond the lifetime of the satellite.
Radiation Hardness of Commercially Available NUV-MT Silicon Photomultipliers
University of Hamburg（汉堡大学）；NCSR “Demokritos（德谟克利特国家研究中心）；Institute of Nuclear and Particle Physics（核与粒子物理研究所）；School of Physics and Astronomy, University of Birmingham（伯明翰大学物理与天文学学院）
A conceptual set-up for measuring the electric field in silicon detectors by electro-optical imaging is proposed. It is based on the Franz-Keldysh effect which describes the electric field dependence of the absorption of light with an energy close to the silicon band gap. Using published data, a measurement accuracy of 1 to 4 kV/cm is estimated. The set-up is intended for determining the electric field in radiation-damaged silicon detectors as a function of irradiation fluence and particle type, temperature and bias voltage. The overall concept and the individual components of the set-up are p…
Radiation damage study of Belle II silicon strip sensors with 90 MeV electron irradiation
Institute of High Energy Physics, Austrian Academy of Sciences（奥地利科学院高能物理研究所）；Aix Marseille Univ, CNRS/IN2P3, CPPM（艾克斯-马赛大学，法国国家科学研究中心/法国原子能和替代能源委员会，粒子与宇宙学实验室）；Indian Institute of Technology Bhubaneswar（布巴内斯瓦尔印度理工学院）；Indian Institute of Technology Madras（马德拉斯印度理工学院）；Malaviya National Institute of Technology Jaipur（斋普尔马拉维亚国立技术学院）；Punjab Agricultural University（旁遮普农业大学）；Tata Institute of Fundamental Research（塔塔基础研究院）；Dipartimento di Fisica, Università di Pisa（比萨大学物理系）
A lot of R & D work is carried out in the CERN RD50 Collaboration to find out the best material for the Si detectors that can be used in the harsh radiation environment of HL-LHC, n and p-MCz Si was identified as one of the prime candidates as a material for strip detector that can be chosen the phase 2 upgrade plan of the new Compact Muon Solenoid tracker detector in 2026. For the very first time, in this work, an advanced four level deep-trap mixed irradiation model for p-MCz Si is proposed by the comparison of experimental data on the full depletion voltage and leakage current to the Shockl…
The irradiation represents a useful tool for determining the characteristics of defects in semiconductors as well as a method to evaluate their degradation, fact with important technological consequences. In this contribution, starting from available data on the degradation of silicon detector characteristics in radiation fields, these effects are explained in the frame of a model that supposes also the production of the SiFFCD defect due to irradiation. The displacement threshold energies - different for different crystallographic axes, considered as parameters of the model, are established a…
Future experiments are using silicon detectors in a high radiation environment and in high magnetic fields. The radiation tolerance of silicon improves by cooling it to temperatures below 180 K. At low temperatures the mobility increases, which leads to larger deflections of the charge carriers by the Lorentz force. A good knowledge of the Lorentz angle is needed for design and operation of silicon detectors. We present measurements of the Lorentz angle between 77 K and 300 K before and after irradiation with a primary beam of 21 MeV protons.
Within CERN RD50 Collaboration, MCz Si was identified as a best material for the detector used in the high luminosity collider experiments. The n in p Si detectors were utmost radiation hard detectors, which can be used for the phase 2 upgrade plan of the new Compact Muon Solenoid tracker detector in 2026. The choice of n or p-MCz Si material depends upon the high electrical charge collection efficiency performance of these detectors over n or p-FZSi detectors. The bulk radiation damage model for n, p-MCz Si need to develop for the designing, development and optimization of the advanced detect…
We have developed a neutron imaging sensor based on an INTPIX4-SOI pixelated silicon device. Neutron irradiation tests are performed at several neutron facilities to investigate sensor's responses for neutrons. Detection efficiency is measured to be around $1.5$\% for thermal neutrons. Upper bound of spatial resolution is evaluated to be $4.1 \pm 0.2 ~μ$m in terms of a standard deviation of the line spread function.
This paper presents the results of the proton irradiation of silicon photomulipliers (SiPMs) by mono-energetic 170 MeV protons with fluence up to 4.6$\times$10$^{9}$ particles/cm$^2$. In our work, three types of silicon photodetectors from Hamamatsu with areas 3$\times$3 mm$^2$ and different subpixel sizes of 25$\times$25 $μ$m$^2$, 50$\times$50 $μ$m$^2$, and 75$\times$75 $μ$m$^2$ were used. The changes in the SiPM dark count rate (DCR) spectrum before and after irradiation in temperatures in the range of 20 $^\circ$C to -65 $^\circ$C are presented. The influence of the DCR changes on the energ…
A method is proposed for determining the electric field in highly-irradiated silicon pad diodes using admittance-frequency (Y-f ), and current measurements (I). The method is applied to Y-f and I data from square n+p diodes of 25mm2 area irradiated by 24 GeV/c protons to four 1MeV neutron equivalent fluences between 3E15 cm^2 and 13E15 cm^2. The measurement conditions were: Reverse voltages between 1V and 1000V, frequencies between 100Hz and 2MHz and temperatures of -20°C and -30°C. The position dependence of the electric field is parameterised by a linear dependence at the two sides of the di…
The existing ATLAS Tracker will be at its functional limit for particle fluences of 10^15 neq/cm^2 (LHC). Thus for the upgrades at smaller radii like in the case of the planned Insertable B-Layer (IBL) and for increased LHC luminosities (super LHC) the development of new structures and materials which can cope with the resulting particle fluences is needed. N-in-p silicon devices are a promising candidate for tracking detectors to achieve these goals, since they are radiation hard, cost efficient and are not type inverted after irradiation. A n-in-p pixel production based on a MPP/HLL design a…
In this contribution we discuss how to prepare some possible detectors - only silicon option being considered, for the new era of HEP challenges because the bulk displacement damage in the detector, consequence of irradiation, produces effects at the device level that limit their long time utilisation, increasing the leakage current and the depletion potential, eventually up to breakdown, and thus affecting the lifetime of detector systems. Physical phenomena that conduce to the degradation of the detector are analysed both at the material and device levels, and some predictions of the time de…
Charge collection properties of depleted CMOS pixel detector prototypes produced on p-type substrate of 2 k$Ω$cm initial resistivity (by LFoundry 150 nm process) were studied using Edge-TCT method before and after neutron irradiation. The test structures were produced for investigation of CMOS technology in tracking detectors for experiments at HL-LHC upgrade. Measurements were made with passive detector structures in which current pulses induced on charge collecting electrodes could be directly observed. Thickness of depleted layer was estimated and studied as function of neutron irradiation …
Standard as well as irradiated silicon pixel detectors developed for the ATLAS experiment were tested in a beam. Digital and analog resolutions were determined comparing the positions measured by a microstrip telescope and by the pixel detector. Digital resolutions of 10 um and analog resolutions of 6 um (before irradiation) and 10 um (after irradiation) are obtained without subtracting the error on the position determined by the telescope.
Protons that are trapped in the Earth's magnetic field are one of the main threats to astronomical X-ray observatories. Soft protons, in the range from tens of keV up to a few MeV, impinging on silicon X-ray detectors can lead to a significant degradation of the detector performance. Especially in low earth orbits an enhancement of the soft proton flux has been found. A setup to irradiate detectors with soft protons has been constructed at the Van-de-Graaff accelerator of the Physikalisches Institut of the University of Tübingen. Key advantages are a high flux uniformity over a large area, to …
In this paper results of Edge-TCT and I-V measurements with passive test structures made in LFoundry 150 nm HV-CMOS process on p-type substrates with different initial resistivities ranging from 0.5 to 3 k$Ω$cm are presented. Samples were irradiated with reactor neutrons up to a fluence of 2$\cdot$10$^{15}$ n$_{\mathrm{eq}}$/cm$^2$. Depletion depth was measured with Edge-TCT. Effective space charge concentration $N_{\mathrm{eff}}$ was estimated from the dependence of depletion depth on bias voltage and studied as a function of neutron fluence. Dependence of $N_{\mathrm{eff}}$ on fluence change…
In this contribution we argue that the main discrepancies between model calculations and experimental data for leakage current after hadron irradiation could be explained considering the contributions of primary defects in silicon: vacancy, interstitial and Si_FFCD defect. The source of discrepancies between data and previous modelling was tentatively attributed to the Si_FFCD defect. Vacancies and interstitials have a major contribution to the current short time after irradiation. If these hypotheses are correct, thus, in conditions of continuous long time irradiation, as e.g. LHC and its upg…
The unique electrical and material properties of 4H-silicon-carbide (4H-SiC) make it a promising candidate material for high rate particle detectors. In contrast to the ubiquitously used silicon (Si), 4H-SiC offers a higher carrier saturation velocity and larger breakdown voltage, enabling a high intrinsic time resolution and mitigating pile-up effects. Additionally, as radiation hardness requirements grow more demanding, wide-bandgap materials such as 4H-SiC could offer better performance. In this work, the detector performance of 50 micron thick 4H-SiC p-in-n planar pad sensors was investiga…
The silicon drift detectors are at the basis of the instrumentation aboard the Large Observatory For x-ray Timing (LOFT) satellite mission, which underwent a three year assessment phase within the "Cosmic Vision 2015 - 2025" long-term science plan of the European Space Agency. Silicon detectors are especially sensitive to the displacement damage, produced by the non ionising energy losses of charged and neutral particles, leading to an increase of the device leakage current and thus worsening the spectral resolution. During the LOFT assessment phase, we irradiated two silicon drift detectors w…
In view of the LHC upgrade phases towards HL-LHC the ATLAS experiment plans to upgrade the Inner Detector with an all silicon system. The n-in-p silicon technology is a promising candidate for the pixel upgrade thanks to its radiation hardness and cost effectiveness, that allow for enlarging the area instrumented with pixel detectors. We present the characterization and performance of novel n-in-p planar pixel sensors produced by CiS (Germany) connected by bump bonding to the ATLAS readout chip FE-I3. These results are obtained before and after irradiation up to a fluence of 10^16 1-MeV n_eq/c…
Silicon Photo-Multipliers (SiPM) are becoming the photo-detector of choice for increasingly more particle detection applications, from fundamental physics to medical and societal applications. One major consideration for their use at high-luminosity colliders is the radiation damage induced by hadrons, which leads to a dramatic increase of the dark count rate. KETEK SiPMs have been exposed to various fluences of reactor neutrons up to $Φ_{neq}$ = 5$\times$10$^{14}$ cm$^{-2}$ (1 MeV equivalent neutrons). Results from the I-V, and C-V measurements for temperatures between $-$30$^\circ$C and $+$3…
This work focuses on the investigation of radiation induced defects responsible for the degradation of silicon detectors. Comparative studies of the defects induced by irradiation with 60Co- rays, 6 and 15 MeV electrons, 23 GeV protons and 1 MeV equivalent reactor neutrons revealed the existence of point defects and cluster related centers having a strong impact on damage properties of Si diodes. The detailed relation between the microscopic reasons as based on defect analysis and their macroscopic consequences for detector performance are presented. In particular, it is shown that the changes…
