We have developed two radiation-hard ASICs for optical data transmission in the ATLAS pixel detector at the LHC at CERN: a driver chip for a Vertical Cavity Surface Emitting Laser (VCSEL) diode for 80 Mbit/s data transmission from the detector, and a Bi-Phase Mark decoder chip to recover the control data and 40 MHz clock received optically by a PIN diode. We have successfully implemented both ASICs in 0.25 mm CMOS technology using enclosed layout transistors and guard rings for increased radiation hardness. We present results from circuits of final design and from irradiation studies with 24 GeV protons up to 80 Mrad (2.6 x 10^15 p/cm^2).
We present the design and the performance of MUX64, a 64-to-1 analogue multiplexer ASIC for the ATLAS High Granularity Timing Detector (HGTD). The MUX64 transmits one of its 64 inputs selected by six address lines for the voltages or temperatures being monitored to an lpGBT ADC channel. The prototype ASICs fabricated in TSMC 130 nm CMOS technology were prepared in wire-bonding and QFN88 packaging format. A total of 280 chips was examined for functionality and quality assurance. The accelerated aging test conducted at 85 degrees celsius shows negligible degradation over 16 days.
The present article introduces a novel ASIC architecture, designed in the context of the ATLAS Tile Calorimeter upgrade program for the High-Luminosity phase of the Large Hadron Collider at CERN. The architecture is based on radiation-tolerant 130 nm Complementary Metal-Oxide-Semiconductor technology, embedding both analog and digital processing of detector signals. A detailed description of the ASIC is given in terms of motivation, design characteristics and simulated and measured performance. Experimental studies, based on 24 prototype units under real particle beam conditions are also prese…
We have developed two radiation-hard ASICs for optical data transmission in the ATLAS pixel detector at the LHC at CERN: a driver chip for a Vertical Cavity Surface Emitting Laser (VCSEL) diode for 80 Mbit/s data transmission from the detector, and a Bi-Phase Mark decoder chip to recover the control data and 40 MHz clock received optically by a PIN diode. We have successfully implemented both ASICs in 0.25 mm CMOS technology using enclosed layout transistors and guard rings for increased radiation hardness. We present results from circuits of final design and from irradiation studies with 24 G…
We report on the design of a serializer ASIC to be used in the ATLAS forward muon detector for trigger data transmission. We discuss the performance of a prototype chip covering power dissipation, latency and stable operating line rate. Tests show that the serializer is capable of running at least at 5.76 Gbps with a bit error ratio below 1x10^{-15}, and a power consumption of 200 mW running at 4.8 Gbps. The latency between the start of loading 30 bits into the serializer to the transmission of the first bit from the serializer is measured to be about 6 ns.
The Trigger Data Serializer (TDS) is a custom ASIC designed for the upgrade of the innermost station of the endcap ATLAS Muon Spectrometer. It is a mixed-signal chip with two working modes that can handle up to 128 detector channels. A total of 6,000 TDS ASICs have been produced for detector operation. This paper discusses a custom automatic test platform we developed to provide quality control of the TDS ASICs. We introduce the design, test procedures, and results obtained from this TDS testing platform.
The ATLAS experiment will replace the present Small Wheel (SW) detector with a New Small Wheel detector (NSW) aiming to improve the performance of muon triggering and precision tracking in the endcap region at the High-Luminosity LHC. Small-strip Thin Gap Chamber (sTGC) is one of the two new detector technologies used in this upgrade. A few custom-designed ASICs are needed for the sTGC detector. We designed an sTGC ASIC interface board to test ASIC-to-ASIC communication and validate the functionality of the entire system. A test platform with the final readout system is set up and the whole sT…
This work presents the first measurements performed on the Timespot1 ASIC. As the second prototype developed for the TimeSPOT project, the ASIC features a 32x32 channels hybrid-pixel matrix. Targeted to space-time tracking applications in High Energy Physics experiments, the system aims to achieve a time resolution of 30 ps or better at a maximum event rate of 3 MHz per channel with a Data Driven interface. Power consumption can be programmed to range between $1.2W/cm^{2}$ and $2.6W/cm^{2}$. The presented results include a description of the ASIC operation and a first characterization of its p…
The upgrade of the ATLAS muon spectrometer for high-luminosity LHC requires new trigger and readout electronics for the various elements of the detector. We present the design of a time-to-digital converter (TDC) ASIC prototype for the ATLAS Monitored Drift Tube (MDT) detector. The chip was fabricated in a GlobalFoundries 130 nm CMOS technology. Studies indicate that its timing and power consumption characteristics meet the design specifications, with a timing bin variation of 40 ps for all 48 channels with a power consumption of about 6.5 mW per channel.
A serializer ASIC and a VCSEL driver ASIC are needed for the front-end optical data transmission in the ATLAS liquid argon calorimeter readout phase-I upgrade. The baseline ASICs are the serializer LOCx2 and the VCSEL driver LOCld, designed in a 0.25-μm Silicon-on-Sapphire (SoS) CMOS technology and consumed 843 mW and 320 mW, respectively. Based on a 130-nm CMOS technology, we design two pin-to-pin-compatible backup ASICs, LOCx2-130 and LOCld-130. Their power consumptions are much lower then of their counterparts, whereas other performance, such as the latency, data rate, and radiation toleran…
We present the prototype of a time-to-digital (TDC) ASIC for the upgrade of the ATLAS Monitored Drift Tube (MDT) detector for high-luminosity LHC operation. This ASIC is based on a previously submitted demonstrator ASIC designed for timing performance evaluation, and includes all features necessary for the various operation modes, as well as the migration to the TSMC 130 nm CMOS technology. We present the TDC design with the emphasis on added features and performance optimization. Tests of the timing performance demonstrate that this ASIC meets the design specifications. The TDC has a bin size…
We have been developing a serializer application-specific integrated circuit (ASIC) based on a commercial 0.25-μm silicon-on-sapphire (SOS) CMOS technology for the ATLAS liquid argon calorimeter front-end electronics upgrade. The first prototype, a 5 Gbps 16:1 serializer has been designed, fabricated, and tested in lab environment and in a 200 MeV proton beam. The test results indicate that the first prototype meets the design goals. The second prototype, a double-lane, 8 Gbps per lane serializer is under development. The post-layout simulation indicates that 8 Gbps is achievable. In this pape…
In this paper, we present the design and test results of LOCx2, a transmitter ASIC for the ATLAS Liquid Argon Calorimeter trigger upgrade. LOCx2 consists of two channels and each channel encodes ADC data with an overhead of 14.3% and transmits serial data at 5.12 Gbps with a latency of less than 27.2 ns. LOCx2 is fabricated with a commercial 0.25-um Silicon-on-Sapphire CMOS technology and is packaged in a 100-pin QFN package. The power consumption of LOCx2 is about 843 mW.
Two optical data link data transmission Application Specific Integrated Circuits (ASICs), the baseline and its backup, have been designed for the ATLAS Liquid Argon (LAr) Calorimeter Phase-I trigger upgrade. The latency of each ASIC and that of its corresponding receiver implemented in a back-end Field-Programmable Gate Array (FPGA) are critical specifications. In this paper, we present the latency measurements and simulation of two ASICs. The measurement results indicate that both ASICs achieve their design goals and meet the latency specifications. The consistency between the simulation and …
The Address in Real Time Data Driver Card (ADDC) is designed to transmit the trigger data in the Micromegas detector of the ATLAS New Small Wheel (NSW) upgrade. The ART signals are generated by the front end ASIC, named VMM chip, to indicate the address of the first above-threshold event. A custom ASIC (ART ASIC) is designed to receive the ART signals from the VMM chip and do the hit-selection processing. Processed data from ART ASIC will be transmitted out of the NSW detector through GBTx serializer, VTTx optical transmitter module and fiber optical links. The ART signal is critical for the A…
Initial performance assessment and calibration techniques of the production monolithic silicon pixel detector ASIC for the detection of electromagnetic showers of TeV energy in the FASER experiment at the LHC
We present the second prototype of a time-to-digital (TDC) ASIC for the upgrade of the ATLAS Monitored Drift Tube (MDT) detector for High-Luminosity LHC operations. Compared to the first prototype, triple modular redundancy has been implemented for the configuration and flow control logic. The total power consumption is increased by less than 10 mW while achieving the same time resolution and channel uniformity. A mini-DAQ system has been built to verify the front-end electronics chain with the new prototype together with other ASICs and boards in triggered mode. Cosmic ray tests with a small-…
The small-strip Thin Gap Chamber (sTGC) will be used for both triggering and precision tracking purposes in the upgrade of the ATLAS forward muon spectrometer. Both sTGC pad and strip detectors are readout by a Trigger Data Serializer (TDS) ASIC in the trigger path. This ASIC has two operation modes to prepare trigger data from pad and strip detectors respectively. The pad mode (pad-TDS) collects the firing status for up to 104 pads from one detector layer and transmits the data at 4.8 Gbps to the pad trigger extractor every 25 ns. The pad trigger extractor collects pad-TDS data from eight det…
Quality control and quality assurance evaluation of ALFE2, a large-dynamic-range front-end ASIC de-veloped for the ATLAS Liquid Argon Calorimeter high-luminosity LHC upgrade
Physics Department, Brookhaven National Laboratory（布鲁克海文国家实验室物理系）；Instrumentation Department, Brookhaven National Laboratory（布鲁克海文国家实验室仪器部）；Department of Physics and Astronomy, Stony Brook University（石溪大学物理与天文系）；IJCLab, Université Paris-Saclay, CNRS/IN2P3（巴黎萨克雷大学IJCLab，CNRS/IN2P3）；ESAT-ADVISE, KU Leuven（荷语鲁汶大学ESAT-ADVISE）；CERN（欧洲核子研究中心）
One of candidates for the International Linear Collider(ILC)'s vertex detector is the Fine Pixel CCD (FPCCD) with a pixel size of 5 \times 5 (\mum^2). Sensor and readout systems are currently being studied and prototypes have been developed. In this paper we will report on the performance of latest developed readout ASIC prototype as well as the outline of the design strategy for the next ASIC prototype.
We present the first characterization results of Timespot1, an ASIC designed in CMOS 28 nm technology, featuring a $32 \times 32$ pixel matrix with a pitch of $55 ~ μm$. Timespot1 is the first small-size prototype, conceived to readout fine-pitch pixels with single-hit time resolution below $50 ~ ps_\text{rms}$ and input rates of several hundreds of kilohertz per pixel. Such experimental conditions will be typical of the next generation of high-luminosity collider experiments, from the LHC run5 and beyond. Each pixel of the ASIC includes a charge amplifier, a discriminator, and a Time-to-Digit…
Particle physics detectors increasingly make use of custom FPGA firmware and application-specific integrated circuits (ASICs) for data readout and triggering. As these designs become more complex, it is important to ensure that they are simulated under realistic operating conditions before beginning fabrication. One tool to assist with the development of such designs is cocotb, an open source digital logic verification framework. Using cocotb, verification can be done at high level using the Python programming language, allowing sophisticated data flow simulations to be conducted and issues to…
We present the characterization and quality control test of a gigabit cable receiver ASIC prototype, GBCR2, for the ATLAS Inner Tracker pixel detector upgrade. GBCR2 equalizes and retimes the uplink electrical signals from RD53B through a 6 m Twinax AWG34 cable to lpGBT. GBCR2 also pre-emphasizes downlink command signals through the same electrical connection from lpGBT to RD53B. GBCR2 has seven uplink channels each at 1.28 Gbps and two downlink channels each at 160 Mbps. The prototype is fabricated in a 65 nm CMOS process. The characterization of GBCR2 has been demonstrated that the total jit…
We have designed three ASICs for possible applications in the optical links of a new layer of pixel detector in the ATLAS experiment for the first phase of the LHC luminosity upgrade. The ASICs include a high-speed driver for the VCSEL, a receiver/decoder to decode the signal received at the PIN diode to extract the data and clock, and a clock multiplier to produce a higher frequency clock to serialize the data for transmission. These ASICs were designed using a 130 nm CMOS process to enhance the radiation-hardness. We have characterized the fabricated ASICs and the submission has been mostly …
We characterize a new x-ray Mixed-Mode Pixel Array Detector (MM-PAD-2.1) Application Specific Integrated Circuit (ASIC). Using an integrating pixel front-end with dynamic charge removal architecture, the MM-PAD-2.1 ASIC extends the maximum measurable x-ray signal (in 20 keV photon units) to > 10$^{7}$ x-rays/pixel/frame while maintaining a low read noise across the full dynamic range, all while imaging continuously at a frame rate of up to 10 kHz. The in-pixel dynamic charge removal mechanism prevents saturation of the input amplifier and proceeds in parallel with signal integration to achieve…
For the High Luminosity upgrade of the Large Hadron Collider the current ATLAS Inner Detector will be replaced by an all-silicon Inner Tracker. The pixel detector will consist of five barrel layers and a number of rings, resulting in about 13 m^2 of instrumented area. Due to the huge non-ionising fluence (1e16 neq/cm^2) and ionising dose (5 MGy), the two innermost layers, instrumented with 3D pixel sensors and 100 um thin planar sensors, will be replaced after about five years of operation. Each pixel layer comprises hybrid detector modules that will be read out by novel ASICs, implemented in …
Scientific detectors are a key technological enabler for many disciplines. Application-specific integrated circuits (ASICs) are used for many of these scientific detectors. Until recently, pixel detector ASICs have been used mainly for analog signal processing of the charge from the sensor layer and the transmission of raw pixel data off the detector ASIC. However, with the availability of more advanced ASIC technology nodes for scientific application, more digital functionality from the computing domains (e.g., compression) can be integrated directly into the detector ASIC to increase data ve…
Today, most X-ray pixel detectors used at light sources transmit raw pixel data off the detector ASIC. With the availability of more advanced ASIC technology nodes for scientific application, more digital functionality from the computing domains (e.g., compression) can be integrated directly into a detector ASIC to increase data velocity. In this paper, we describe a lightweight, user-configurable detector ASIC digital architecture with on-chip compression which can be implemented in \SI{130}{\nm} technologies in a reasonable area on the ASIC periphery. In addition, we present a design to effi…
We develop the vertex detector for the international linear collider (ILC) using the FPCCD (Fine Pixel CCD), whose pixel size is 5 x 5 um2. Together with the FPCCD sensor, a prototype of the readout ASIC was developed in 2008. The readout ASIC was confirmed to work correctly at slow readout speed (1.5 Mpix/sec). In this letter, we describe the status of the performance study for the readout ASIC.
The ForwArd Search ExpeRiment (FASER) is an experiment searching for new light and weakly-interacting particles at CERN's Large Hadron Collider. FASER is composed of different sub-detectors, including silicon microstrip detectors, scintillator counters and an electromagnetic calorimeter. In this paper, a new preshower detector for the FASER experiment is presented. The new detector, based on monolithic pixel ASICs, will provide excellent spatial and time resolutions and a large charge dynamic range. First results from a prototype chip produced by IHP in 130 nm SiGe BiCMOS technology are shown.
Test beam results obtained with 3D pixel sensors bump-bonded to the RD53A prototype readout ASIC are reported. Sensors from FBK (Italy) and IMB-CNM (Spain) have been tested before and after proton-irradiation to an equivalent fluence of about $1$ $\times$ $10^{16}$ $\text{n}_{\text{eq}}$ cm$^{-2}$ (1 MeV equivalent neutrons). This is the first time that one single collecting electrode fine pitch 3D sensors are irradiated up to such fluence bump-bonded to a fine pitch ASIC. The preliminary analysis of the collected data shows no degradation on the hit detection efficiencies of the tested sensor…
The ATLAS experiment pixel detector upgrade plans are focused on development of new technology, including the FE-I4 readout integrated circuit. The first upgrade project to make use of this new technology is an "Insertable B-Layer" (IBL) pixel detector to be installed on a replacement beam pipe in 2013. The IBL will fit inside and not alter the existing ATLAS pixel detector. However, the possibility is being studied to replace the pixel whole detector in 2018 with a lower mass, higher performance instrument based on the FE-I4 chip and new mechanical structures.
We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade. The first prototype, GBCR1, has four upstream receiver channels and one downstream transmitter channel with pre-emphasis. Each upstream channel receives the data at 5.12 Gbps through a 5 meter AWG34 Twinax cable from an ASIC driver located on the pixel module and restores the signal from the high frequency loss due to the low mass cable. The signal is retimed by a recovered clock before it is sent to the optical transmitt…
A prototype particle tracking telescope has been constructed using Timepix and Medipix ASIC hybrid pixel assemblies as the six sensing planes. Each telescope plane consisted of one 1.4 cm2 assembly, providing a 256x256 array of 55 micron square pixels. The telescope achieved a pointing resolution of 2.3 micron at the position of the device under test. During a beam test in 2009 the telescope was used to evaluate in detail the performance of two Timepix hybrid pixel assemblies; a standard planar 300 micron thick sensor, and 285 micron thick double sided 3D sensor. This paper describes a detaile…
In this talk we present the basis for the protocol for radiation monitoring of the ATLAS Pixel Sensors. The monitoring is based on a current measurement system, HVPP4. The status on the ATLAS HVPP4 system development is also presented.
An innovative X-ray imaging sensor with intrinsic digital characteristics is presented. It is based on Chromatic Photon Counting technology. The detector is able to count individually the incident X-ray photons and to separate them according to their energy (two 'color' images per exposure). The energy selection occurs in real time and at radiographic imaging speed (GHz global counting rate). Photon counting, color mode and a very high spatial resolution (more than 10 l.p./mm at MTF50) allow to obtain an optimal ratio between image quality and absorbed dose. The individual block of the imaging…
The continued desire for X-ray pixel detectors with higher frame rates will stress the ability of application-specific integrated circuit (ASIC) designers to provide sufficient off-chip bandwidth to reach continuous frame rates in the 1 MHz regime. To move from the current 10 kHz to the 1 MHz frame rate regime, ASIC designers will continue to pack as many power-hungry high-speed transceivers at the periphery of the ASIC as possible. In this paper, however, we present new strategies to make the most efficient use of the off-chip bandwidth by utilizing data compression schemes for X-ray photon-c…
The ATLAS pixel detector is the innermost detector of the ATLAS experiment at the Large Hadron Collider at CERN. With approximately 80 million readout channels, the ATLAS silicon pixel detector is a high-acceptance, high-resolution, low-noise tracking device. Providing the desired refinement in charged track pattern recognition capability in order to meet the stringent track reconstruction requirements, the pixel detector largely defines the ability of ATLAS to effectively resolve primary and secondary vertices and perform efficient flavor tagging essential for discovery of new physics. Being …
This paper presents a small-area monolithic pixel detector ASIC designed in 130 nm SiGe BiCMOS technology for the upgrade of the pre-shower detector of the FASER experiment at CERN. The purpose of this prototype is to study the integration of fast front-end electronics inside the sensitive area of the pixels and to identify the configuration that could satisfy at best the specifications of the experiment. Self-induced noise, instabilities and cross-talk were minimised to cope with the several challenges associated to the integration of pre-amplifiers and discriminators inside the pixels. The m…
The ATLAS pixel detector is a high precision silicon tracking device located closest to the LHC interaction point. It belongs to the first generation of its kind in a hadron collider experiment. It will provide crucial pattern recognition information and will largely determine the ability of ATLAS to precisely track particle trajectories and find secondary vertices. It was the last detector to be installed in ATLAS in June 2007, has been fully connected and tested in-situ during spring and summer 2008. It is currently in a commissioning phase using cosmic-ray events. We present the highlights …
Development and characterization of hybrid MCP-PMT with embedded Timepix4 ASIC used as pixelated anode
INFN, Division of Ferrara（意大利国家核物理研究所费拉拉分部）；Dept. of Physics and Earth Science, University of Ferrara（费拉拉大学地球科学与物理学系）；EP Department, CERN（欧洲核子研究中心实验物理部）
The LHC is expected to reach luminosities up to 3000fb-1 and the innermost layer of the ATLAS upgrade plans to cope with higher occupancy and to decrease the pixel size. 3D-Si sensors are a good candidate for the innermost layer of the ATLAS pixel upgrade since they exhibit good performance under high fluences and the new designs will have smaller pixel size to fulfill the electronics expectations. This paper reports TCAD simulations of the 3D-Si sensors designed at IMB-CNM with non passing-through columns that are being fabricated for the next innermost layer of the ATLAS pixel upgrade, shows…
This paper presents several component prototypes towards a low-latency, small-form-factor optical link designed for the ATLAS Liquid Argon Calorimeter Phase-I trigger upgrade. A prototype of the custom-made dual-channel optical transmitter module, the Miniature optical Transmitter (MTx), with separate transmitter optical sub-assemblies (TOSAs) has been demonstrated at data rates up to 8 Gbps per channel. A Vertical-Cavity Surface-Emitting Laser (VCSEL) driver ASIC has been developed and is used in the current MTx prototypes. A serializer ASIC prototype, operating at up to 8 Gbps per channel, h…
Single Event Effects (SEEs) - predominately bit-flips in electronics caused by particle interactions - are a major concern for ASICs operated in high radiation environments such as ABCStar ASICs, which are designed to be used in the future ATLAS ITk strip tracker. The chip design is therefore optimised to protect it from SEEs by implementing triplication techniques such as Triple Modular Redundancy (TMR). In order to verify the radiation protection mechanisms of the chip design, the cross-section for Single Event Upsets (SEUs), a particular class of SEEs, is measured by exposing the chip to hi…
The Tile Calorimeter at ATLAS is a hadron calorimeter based on steel plates and scintillating tiles read out by PMTs. The current read-out system uses standard ADCs and custom ASICs to digitize and temporarily store the data on the detector. However, only a subset of the data is actually read out to the counting room. The on-detector electronics will be replaced around 2023. To achieve the required reliability the upgraded system will be highly redundant. Here the ASICs will be replaced with Kintex-7 FPGAs from Xilinx. This, in addition to the use of multiple 10 Gbps optical read-out links, wi…
We have developed two radiation-hard ASICs for optical data transmission in the ATLAS pixel detector at the LHC at CERN: a driver chip for a Vertical Cavity Surface Emitting Laser (VCSEL) diode for 80 Mbit/s data transmission from the detector, and a Bi-Phase Mark decoder chip to recover the control data and 40 MHz clock received optically by a PIN diode. We have successfully implemented both ASICs in 0.25 micron CMOS technology using enclosed layout transistors and guard rings for increased radiation hardness. We present results of the performance of these chips, including irradiation with 24…
The on-detector optical link of the ATLAS pixel detector contains radiation-hard receiver chips to decode bi-phase marked signals received on PIN arrays and data transmitter chips to drive VCSEL arrays. The components are mounted on hybrid boards (opto-boards). We present results from the irradiation studies with 24 GeV protons up to 32 Mrad (1.2 x 10^15 p/cm^2) and the experience from the production.
The ATLAS detector is currently being upgraded with a new layer of pixel based charged particle tracking and a new arrangement of the services for the pixel detector. These upgrades require the replacement of the opto-boards previously used by the pixel detector. In this report we give details on the design and production of the new opto-boards.
The ATLAS Planar Pixel Sensor R&D Project is a collaboration of 17 institutes and more than 80 scientists. Their goal is to explore the operation of planar pixel sensors for the tracker upgrade at the High Luminosity-Large Hadron Collider (HL-LHC). This work will give a summary of the achievements on radiation studies with n-in-n and n-in-p pixel sensors, bump-bonded to ATLAS FE-I3 and FE-I4 readout chips. The summary includes results from tests with radioactive sources and tracking efficiencies extracted from test beam measurements. Analysis results of ${2\cdot10^{16}} \text{n}_{\text{eq}}\te…
The ATLAS detector has to undergo significant updates at the end of the current decade, in order to withstand the increased occupancy and radiation damage that will be produced by the high-luminosity upgrade of the Large Hadron Collider. In this presentation we give an overview of the recent accomplishments of the R&D activity on the planar pixel sensors for the ATLAS Inner Detector upgrade.
The on-detector optical link of the ATLAS pixel detector contains radiation-hard receiver chips to decode bi-phase marked signals received on PIN arrays and data transmitter chips to drive VCSEL arrays. The components are mounted on hybrid boards (opto-boards). We present results from the opto-boards and from irradiation studies with 24 GeV protons up to 33 Mrad (1.2 x 10^15 p/cm^2).
We present a programmable time alignment scheme used in an ASIC for the ATLAS forward muon trigger development. The scheme utilizes regenerated clocks with programmable phases to compensate for the timing offsets introduced by different detector trace lengths. Each ASIC used in the design has 104 input channels with delay compensation circuitry providing steps of ~ 3 ns and a full range of 25 ns for each channel. Detailed implementation of the scheme including majority logic to suppress single-event effects is presented. The scheme is flexible and fully synthesizable. The approach is adaptable…
The Pixel Detector of the ATLAS experiment has shown excellent performance during the whole Run-1 of LHC. Taking advantage of the long shutdown, the detector was extracted from the experiment and brought to surface, to equip it with new service quarter panels, to repair modules and to ease installation of a new innermost layer, the Insertable B-Layer (IBL). An overview of the operational experience, the refurbishing of the Pixel Detector and of the IBL project as well as the experience in its construction, integration and commissioning are described.
