arXivDaily arXiv每日学术速递 周一至周五更新
arXiv 2008.09738physics.ins-det
收藏

1.28和5.12 Gbps多通道双轴电缆接收器ASIC,用于ATLAS内部跟踪器像素检测器升级

1.28 and 5.12 Gbps multi-channel twinax cable receiver ASICs for the ATLAS Inner Tracker Pixel Detector Upgrade

Chufeng Chen, Datao Gong, Suen Hou, Guangming Huang, Xing Huang, Szymon Kulis, Paul Leroux, Chonghan Liu, Tiankuan Liu, Paulo Moreira, Jefery Prinzie, Peilong Wang, Jingbo Ye

摘要:

我们提出了两个原型的千兆位收发器ASIC,GBCR 1和GBCR 2,都设计在一个65纳米CMOS技术的ATLAS内部跟踪器像素检测器读出升级。第一个原型,GBCR 1,有四个上行接收机通道和一个下行发射机通道与预加重。每个上行通道通过5米AWG 34 Twinax电缆以5.12 Gbps的速率从位于像素模块上的ASIC驱动器接收数据,并从低质量电缆造成的高频损耗中恢复信号。信号在发送到光发射器VTRx+之前由恢复的时钟重新定时。下游驱动器旨在通过同一电缆将2.56 Gbps信号从lpGBT传输到像素模块上的电子器件。在GBCR 1的输出端,恢复信号的峰-峰抖动(除非指定,否则整个纸张抖动始终为峰-峰)为35.4 ps,在电缆端的下行通道为138 ps。GBCR 1功耗为318 mW,并经过测试。第二个原型GBCR 2有七个上行通道和两个下行通道。每个上行通道以1.28 Gbps的速率工作,通过1米定制FLEX电缆和6米AWG 34 Twinax电缆直接从RD 53 B ASIC恢复数据。每个上行信道的均衡信号由输入的1.28 GHz相位可编程时钟重新定时。与FLEX输入端的信号相比,当重定时逻辑为0时,均衡信号的附加抖动约为80 ps。当重定时逻辑开启时,假设1.28 GHz重定时时钟来自lpGBT,则GBCR 2输出的抖动为50 ps。下行链路被设计为通过相同的电缆连接将160 Mbps信号从lpGBT传输到RD 53 B,并且在电缆末端的抖动约为157 ps。当重定时逻辑开启时,GBCR 2的功耗约为150 mW。该设计于2019年11月提交。

英文摘要:

We present two prototypes of a gigabit transceiver ASIC, GBCR1 and GBCR2, both designed in a 65-nm CMOS technology for the ATLAS Inner Tracker Pixel Detector readout upgrade. The first prototype, GBCR1, has four upstream receiver channels and one downstream transmitter channel with pre-emphasis. Each upstream channel receives the data at 5.12 Gbps through a 5 meter AWG34 Twinax cable from an ASIC driver located on the pixel module and restores the signal from the high frequency loss due to the low mass cable. The signal is retimed by a recovered clock before it is sent to the optical transmitter VTRx+. The downstream driver is designed to transmit the 2.56 Gbps signal from lpGBT to the electronics on the pixel module over the same cable. The peak-peak jitter (throughout the paper jitter is always peak-peak unless specified) of the restored signal is 35.4 ps at the output of GBCR1, and 138 ps for the downstream channel at the cable ends. GBCR1 consumes 318 mW and is tested. The second prototype, GBCR2, has seven upstream channels and two downstream channels. Each upstream channel works at 1.28 Gbps to recover the data directly from the RD53B ASIC through a 1 meter custom FLEX cable followed by a 6 meter AWG34 Twinax cable. The equalized signal of each upstream channel is retimed by an input 1.28 GHz phase programmable clock. Compared with the signal at the FLEX input, the additional jitter of the equalized signal is about 80 ps when the retiming logic is o . When the retiming logic is on, the jitter is 50 ps at GBCR2 output, assuming the 1.28 GHz retiming clock is from lpGBT. The downstream is designed to transmit the 160 Mbps signal from lpGBT through the same cable connection to RD53B and the jitter is about 157 ps at the cable ends. GBCR2 consumes about 150 mW when the retiming logic is on. This design was submitted in November 2019.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑