A simple and most promising oxide-assisted catalyst-free method is used to prepare silicon nitride nanowires that give rise to high yield in a short time. After a brief analysis of the state of the art, we reveal the crucial role played by the oxygen partial pressure: when oxygen partial pressure is slightly below the threshold of passive oxidation, a high yield inhibiting the formation of any silica layer covering the nanowires occurs and thanks to the synthesis temperature one can control nanowire dimensions.
A simple method is developed to synthesize gram quantities of uniform Ge nanowires (GeNWs) by chemical vapor deposition on preformed, monodispersed seed-particles loaded onto high surface area silica support. Various chemical functionalization schemes are investigated to passivate the GeNW surfaces using alkanethiols and alkyl Grignard reactions. The stability of functionalization against oxidation of germanium for various alkyl chain lengths is elucidated by X-ray photoelectron spectroscopy. Among all schemes tested, long chain alkanethiols (>=C12) are found to impart the most stable GeNW pas…
Cuprous oxide (Cu2O) nanowires were grown by a simple, catalyst-free thermal oxidation method starting from a copper foil substrate. Wire growth was performed at different conditions by varying oxygen partial pressure and heating temperature, and produced structural defects such as stacking faults and twin structures of grown nanowires were characterized by transmission electron microscopy. A moderate oxygen partial pressure ~5% with a relatively high temperature at 500 oC is found to be an optimal condition for growing high-quality Cu2O nanowires, while either lowering temperature or enhancin…
Phenylenediamine (PDA) was chosen as a coordinating, reducing, and capping agent to effectively direct growth and protect against oxidation of Cu nanowires (Cu NWs) in an aqueous solution. PDA was found to reduce Cu (II) to Cu (I) at room temperature, and stabilize the resulting Cu (I) by forming a coordination complex. The presence of a stable Cu (I) complex is the key step in the synthesis of Cu NWs under mild conditions. Different PDA isomers lead to different growth paths of forming Cu NWs. Both pPDA and mPDA-synthesized Cu NWs were covered with a thin layer of polyphenylenediamine and sho…
The recent discovery of excellent thermoelectric properties and topological surface states in SnTe-based compounds has attracted extensive attention in various research areas. Indium doped SnTe is of particular interest because, depending on the doping level, it can either generate resonant states in the bulk valence band leading to enhanced thermoelectric properties, or induce superconductivity that coexists with topological states. Here we report on the vapor deposition of In-doped SnTe nanowires and the study of their surface oxidation and thermoelectric properties. The nanowire growth is a…
Large-scale CuO nanowires are commonly synthesized by the thermal oxidation method. However, the growth mechanism remains controversial between diffusion growth mechanism and vapor-solid (VS) growth mechanism. In this study, we investigated the morphology and atomic structure of the CuO nanowires by electron microscopes to clarify the growth mechanism. We found that they were grown with the annealing ambient during the cooling process and there were screw dislocations in the nanowires. These features indicate that the VS growth mechanism is applicable to explain the growth of the CuO nanowires…
In-depth understanding of the retarded oxidation phenomenon observed during the oxidation of silicon nanostructures is proposed. The wet thermal oxidation of various silicon nanostructures such as nanobeams, concave/convex nanorings and nanowires exhibits an extremely different and complex behavior. Such effects have been investigated by the modeling of the mechanical stress generated during the oxidation process explaining the retarded regime. The model describes the oxidation kinetics of silicon nanowires down to a few nanometers while predicting reasonable and physical stress levels at the …
We report the growth of InAs$_{1-x}$Sb$_{x}$ nanowires ($0\leq x \leq 0.15$) grown by catalyst-free molecular beam epitaxy on silicon (111) substrates. We observed a sharp decrease of stacking fault density in the InAs$_{1-x}$Sb$_{x}$ nanowire crystal structure with increasing antimony content. This decrease leads to a significant increase in the field-effect mobility, this being more than three times greater at room temperature for InAs$_{0.85}$Sb$_{0.15}$ nanowires than InAs nanowires.
The addition of boron to GaAs nanowires grown by self-catalyzed molecular beam epitaxy was found to have a strong effect on the nanowire morphology, with axial growth greatly reduced as the nominal boron concentration was increased. Transmission electron microscopy measurements show that the Ga catalyst droplet was unintentionally consumed during growth. Concurrent radial growth, a rough surface morphology and tapering of nanowires grown under boron flux suggest that this droplet consumption is due to reduced Ga adatom diffusion on the nanowire sidewalls in the presence of boron. Modelling of …
Morphological, optical and transport properties of GaN and InN nanowires grown by molecular beam epitaxy (MBE) have been studied. The differences between the two materials in respect to growth parameters and optimization procedure was stressed. The nanowires crystalline quality has been investigated by means of their optical properties. A comparison of the transport characteristics was given. For each material a band schema was shown, which takes into account transport and optical features and is based on Fermi level pinning at the surface.
Gallium nitride nanowires were grown on c-plane, r-plane and m-plane sapphire substrates in a showerhead metalorganic chemical vapor deposition system using nickel catalyst with trimethylgallium and ammonia as precursors. We studied the influence of carrier gas, growth temperature, reactor pressure, reactant flow rates and substrate orientation in order to obtain thin nanowires. The nanowires grew along the <10-11> and <10-10> axes depending on the substrate orientation. These nanowires were further characterized using x-ray diffraction, electron microscopy, photoluminescence and Raman spectro…
Self-limiting oxidation of nanowires has been previously described as a reaction- or diffusion-controlled process. In this letter, the concept of finite reactive region is introduced into a diffusion-controlled model, based upon which a two-dimensional cylindrical kinetics model is developed for the oxidation of silicon nanowires and is extended for tungsten. In the model, diffusivity is affected by the expansive oxidation reaction induced stress. The dependency of the oxidation upon curvature and temperature is modeled. Good agreement between the model predictions and available experimental d…
Incorporation of Bi into GaAs-(Ga,Al)As-Ga(As,Bi) core-shell nanowires grown by molecular beam epitaxy is studied with transmission electron microscopy. Nanowires are grown on GaAs(111)B substrates with Au-droplet assisted mode. Bi-doped shells are grown at low temperature (300 °C) with a close to stoichiometric Ga/As flux ratio. At low Bi fluxes, the Ga(As,Bi) shells are smooth, with Bi completely incorporated into the shells. Higher Bi fluxes (Bi/As flux ratio ~ 4%) led to partial segregation of Bi as droplets on the nanowires sidewalls, preferentially located at the nanowire segments with w…
We have investigated in-situ Si doping of InAs nanowires grown by molecular beam epitaxy from gold seeds. The effectiveness of n-type doping is confirmed by electrical measurements showing an increase of the electron density with the Si flux. We also observe an increase of the electron density along the nanowires from the tip to the base, attributed to the dopant incorporation on the nanowire facets whereas no detectable incorporation occurs through the seed. Furthermore the Si incorporation strongly influences the lateral growth of the nanowires without giving rise to significant tapering, re…
Bottom up nanowires are attractive for realizing semiconductor devices with extreme heterostructures because strain relaxation through the nanowire sidewalls allows the combination of highly lattice mismatched materials without creating dislocations. The resulting nanowires are used to fabricate light emitting diodes (LEDs), lasers, solar cells and sensors. However, expensive single crystalline substrates are commonly used as substrates for nanowire heterostructures as well as for epitaxial devices, which limits the manufacturability of nanowire devices. Here, we demonstrate nanowire LEDs dire…
Doping of III-nitride based compound semiconductor nanowires is still a challenging issue to have a control over the dopant distribution in precise locations of the nanowire optoelectronic devices. Knowledge of the dopant incorporation and its pathways in nanowires for such devices is limited by the growth methods. We report the direct evidence of incorporation pathway for Mg dopants in p-type nonpolar GaN nanowires grown via vapour-liquid-solid (VLS) method in a chemical vapour deposition technique for the first time. Mg incorporation is confirmed using X-ray photoelectron (XPS) and electron …
The present study elucidates the correlation between the structural and optical properties of GaN nanowires grown on Si(111) substrate by plasma assisted molecular beam epitaxy (PA-MBE) technique under various growth conditions. GaN NWs exhibiting different shapes, sizes and distribution were grown at various substrate temperatures with same Ga-N (III-V) ratio of 0.4. We observe that sample grown at lower substrate temperature (~700 degC) results 2-dimensional island like structure with almost very little (~30%) circularity while increasing substrate temperature (>770 degC) leads to growth of …
Optically active gold-catalyzed ZnTe nanowires have been grown by molecular beam epitaxy, on a ZnTe(111) buffer layer, at low temperature 350\degree under Te rich conditions, and at ultra-low density (from 1 to 5 nanowires per micrometer^{2}. The crystalline structure is zinc blende as identified by transmission electron microscopy. All nanowires are tapered and the majority of them are <111> oriented. Low temperature micro-photoluminescence and cathodoluminescence experiments have been performed on single nanowires. We observe a narrow emission line with a blue-shift of 2 or 3 meV with respec…
SnTe topological crystalline insulator nanowires have been grown by molecular beam epitaxy on graphene/SiC substrates. The nanowires have cubic rock-salt structure, they grow along [001] crystallographic direction and have four sidewalls consisting of {100} crystal planes known to host metallic surface states with Dirac dispersion. Thorough high resolution transmission electron microscopy investigations show that the nanowires grow on graphene in the van der Walls epitaxy mode induced when the catalyzing Au nanoparticle mixes with Sn delivered from SnTe flux, providing liquid Au-Sn alloy. The …
The synthesis, morphology and magneto-transport properties of nanostructure-engineered charge-ordered Pr0.5Ca0.5MnO3 grown on ZnO nanowires are reported. The stability of the charge-ordering can be tuned, but more interestingly the sign of the magnetoresistance is inverted at low temperatures. Coexistence of ferromagnetic clusters on the surface and antiferromagnetic phase in the core of the grains were considered in order to understand these features. This work suggests that such a process of growing on nanowires network can be readily extended to other transition metal oxides and open doors …
Mn-doped GaAs nanowires were grown in the self-catalytic growth mode on oxidized Si(100) surface by molecular beam epitaxy and characterized by scanning and transmission electron microscopy, Raman scattering, photoluminescence, cathodoluminescence, and electron transport measurements. The transmission electron microscopy studies evidenced the substantial accumulation of Mn inside the catalyzing Ga droplets at the top of the nanowires. Optical and transport measurements revealed that the limit of Mn content for self-catalysed growth of GaAs nanowires corresponds to the doping level, i.e., is mu…
GaAs:Mn nanowires were obtained on GaAs(001) and GaAs(111)B substrates by molecular beam epitaxial growth of (Ga,Mn)As at conditions leading to MnAs phase separation. Their density is proportional to the density of catalyzing MnAs nanoislands, which can be controlled by the Mn flux and/or the substrate temperature. Being rooted in the ferromagnetic semiconductor (Ga,Mn)As, the nanowires combine one-dimensional properties with the magnetic properties of (Ga,Mn)As and provide natural, self assembled structures for nanospintronics.
Moire based strain analysis in wurtzite GaAs -- rock-salt (Pb,Sn)Te core-shell nanowires grown by molecular beam epitaxy
Institute of Physics, Polish Academy of Sciences（波兰科学院物理研究所）；Faculty of Physics, University of Warsaw（华沙大学物理学院）；Ensemble3 Centre of Excellence（Ensemble3卓越中心）；International Research Center MagTop, Institute of Physics, Polish Academy of Sciences（波兰科学院物理研究所国际研究中心MagTop）
We analyse the morphological, structural and luminescence properties of self-assembled ZnO nanowires grown by chemical vapour transport on Si(001). The examination of nanowire ensembles by scanning electron microscopy reveals that a non-negligible fraction of nanowires merge together forming coalesced aggregates during growth. We show that the coalescence degree can be unambiguously quantified by a statistical analysis of the cross-sectional shape of the nanowires. The examination of the structural properties by X-ray diffraction evidences that the nanowires crystallize in the wurtzite phase, …
We demonstrate a new method to measure absorption coefficients in any family of nanowires, provided they are grown on a substrate having considerable difference in permittivity with the nanowire-air matrix. In the case of high crystal quality, strain-free GaN nanowires, grown on Si (111) substrates with a density of ~1010 cm-2, the extracted absorption coefficients do not exhibit any enhancement compared to bulk GaN values, unlike relevant claims in the literature. This may be attributed to the relatively small diameters, short heights, and high densities of our nanowire arrays.
Structural and magnetic properties of (In,Ga)As-(Ga,Mn)As core-shell nanowires grown by molecular beam epitaxy on GaAs(111)B substrate with gold catalyst have been investigated.(In,Ga)As core nanowires were grown at high temperature (500 °C) whereas (Ga,Mn)As shells were deposited on the {1-100} side facets of the cores at much lower temperature (220 °C). High resolution transmission electron microscopy images and high spectral resolution Raman scattering data show that both the cores and the shells of the nanowires have wurtzite crystalline structure. Scanning and transmission electron micros…
Growth of GaN nanowires are carried out via metal initiated vapor-liquid-solid mechanism, with Au as the catalyst. In chemical vapour deposition technique, GaN nanowires are usually grown at high temperatures in the range of 900-1100 ^oC because of low vapor pressure of Ga below 900 ^oC. In the present study, we have grown the GaN nanowires at a temperature, as low as 700 ^oC. Role of indium in the reduction of growth temperature is discussed in the ambit of Raoult's law. Indium is used to increase the vapor pressure of the Ga sufficiently to evaporate even at low temperature initiating the gr…
We have conducted a detailed thin film growth structure of oxygen engineered monoclinic HfO$_{2\pm x}$ grown by reactive molecular beam epitaxy (MBE). The oxidation conditions induce a switching between ($\bar{1}11$) and (002) texture of hafnium oxide. The band gap of oxygen deficient hafnia decreases with increasing amount of oxygen vacancies by more than 1 eV. For high oxygen vacancy concentrations, defect bands form inside the band gap that induce optical transitions and $p$-type conductivity. The resistivity changes by several orders of magnitude as a function of oxidation conditions. Oxyg…
Highly sensitive and fast photodetector devices with CdSe quantum nanowires as active elements have been developed exploiting the advantages of electro- and wet-chemical routes. Bismuth nanoparticles electrochemically synthesized directly onto interdigitating platinum electrodes serve as catalysts in the following solution-liquid-solid synthesis of quantum nanowires directly on immersed substrates under mild conditions at low temperature. This fast and simple preparation process leads to a photodetector device with a film of nanowires of limited thickness bridging the electrode gaps, in which …
Selective area growth (SAG) of nanowires and networks promise a route toward scalable electronics, photonics and quantum devices based on III-V semiconductor materials. The potential of high-mobility SAG nanowires however is not yet fully realized, since interfacial roughness, misfit dislocations at the nanowire/substrate interface and non-uniform composition due to material intermixing all scatter electrons. Here, we explore SAG of highly lattice-mismatched InAs nanowires on insulating GaAs(001) substrates and address these key challenges. Atomically smooth nanowire/substrate interfaces are a…
Nanogenerators based on piezoelectric materials convert ever-present mechanical vibrations into electrical power for energetically autonomous wireless and electronic devices. Nanowires of piezoelectric polymers are particularly attractive for harvesting mechanical energy in this way, as they are flexible, lightweight and sensitive to small vibrations. Previous studies have focused exclusively on nanowires grown by electrospinning, but this involves complex equipment, and high voltages of $\approx$ 10 kV that electrically pole the nanowires and thus render them piezoelectric. Here we demonstrat…
A 2D layer of spherical, crystalline Ge nanodots embedded in SiO2 was formed by low pressure chemical vapour deposition combined with furnace oxidation and rapid thermal annealing. The samples were characterized structurally by using transmission electron microscopy and rutherford back scattering spectrometry, as well as electrically by measuring CV and IV characteristics. It was found that formation of a high density Ge dots took place due to oxidation induced Ge segregation. The dots are situated in the SiO2 on the average distance 5 nm from the substrate. Strong evidence of charge storage e…
The influence of local oxidation in silicon nanowires on hole transport, and hence the effect of varying the oxidation state of silicon atoms at the wire surface, is studied using density functional theory in conjunction with a Green's function scattering method. For silicon nanowires with growth direction along [110] and diameters of a few nanometers, it is found that the introduction of oxygen bridging and back bonds does not significantly degrade hole transport for voltages up to several hundred millivolts relative to the valence band edge. As a result, the mean free paths are comparable to…
Hexagonal group IV materials like silicon and germanium are expected to display remarkable optoelectronic properties for future development of photonic technologies. However, the fabrication of hexagonal group IV semiconductors within the vapour-liquid-solid method has been obtained using gold as a catalyst thus far. In this letter, we show the synthesis of hexagonal Ge on self-assisted GaAs nanowires using molecular beam epitaxy. With an accurate tuning of the Ga and As molecular beam flux we selected the crystal phase, cubic or hexagonal, of the GaAs NWs during the growth. A 500 nm-long hexa…
We realize growth of self-catalyzed core-shell GaAs/GaAsP nanowires (NWs) on Si substrates using molecular-beam epitaxy. Transmission electron microscopy (TEM) of single GaAs/GaAsP NWs confirms their high crystal quality and shows domination of the zinc-blende phase. This is further confirmed in optics of single NWs, studied using cw and time-resolved photoluminescence (PL). A detailed comparison with uncapped GaAs NWs emphasizes the effect of the GaAsP capping in suppressing the non-radiative surface states: significant PL enhancement in the core-shell structures exceeding 2000 times at 10K i…
We present direct evidence of enhanced Ga interdiffusion in InAs free-standing nanowires grown at moderate temperatures by molecular beam epitaxy on GaAs (111)B. Scanning electron microscopy together with X-ray diffraction measurements in coplanar and grazing incidence geometries show that nominally grown InAs NWs are actually made of In$_{0.86}$Ga$_{0.14}$As. Unlike typical vapor-liquid-solid growth, these nanowires are formed by diffusion-induced growth combined with strong interdiffusion from substrate material. Based on the experimental results, a simple nanowire growth model accounting fo…
We report a detailed magnetic study of a new type of self-organized nanowires disclosed briefly previously [B. Borca et al., Appl. Phys. Lett. 90, 142507 (2007)]. The templates, prepared on sapphire wafers in a kinetically-limited regime, consist of uniaxially-grooved W(110) surfaces, with a lateral period here tuned to 15nm. Fe deposition leads to the formation of (110) 7 nm-wide wires located at the bottom of the grooves. The effect of capping layers (Mo, Pd, Au, Al) and underlayers (Mo, W) on the magnetic anisotropy of the wires was studied. Significant discrepancies with figures known for …
The accurate control of the crystal phase in III-V semiconductor nanowires (NWs) is an important milestone for device applications. In this work, we present a method to select and maintain the wurtzite (WZ) crystal phase in self-assisted NWs. By choosing a specific regime where the NW growth process is a self-regulated system, the main experimental parameter to select the zinc-blende (ZB) or WZ phase is the V/III flux ratio. The latter can be monitored by changing the As flux, and drives the system toward a stationary regime when the wetting angle of the Ga droplet falls in a target interval, …
GaN nanowires grown by molecular beam epitaxy generally suffer from dominant nonradiative recombination, which is believed to originate from point defects. To suppress the formation of these defects, we explore the synthesis of GaN nanowires at temperatures up to 915 $°C$ enabled by the use of thermally stable TiN$_x$/Al$_2$O$_3$ substrates. These samples exhibit indeed bound exciton decay times approaching those measured for state-of-the-art bulk GaN. However, the decay time is not correlated with the growth temperature, but rather with the nanowire diameter. The inverse dependence of the dec…
N-type doping of GaAs nanowires has proven to be difficult because the amphoteric character of silicon impurities is enhanced by the nanowire growth mechanism and growth conditions. The controllable growth of n-type GaAs nanowires with carrier density as high as 1020 electron/cm3 by self-assisted molecular beam epitaxy using Te donors is demonstrated here. Carrier density and electron mobility of highly doped nanowires are extracted through a combination of transport measurement and Kelvin probe force microscopy analysis in single-wire field-effect devices. Low-temperature photoluminescence is…
InAs nanowires were grown on GaAs substrates by the Au-assisted vapour-liquid-solid (VLS) method in a gas source molecular beam epitaxy (GS-MBE) system. Passivation of the InAs nanowires using InP shells proved difficult due to the tendency for the formation of axial rather than core-shell structures. To circumvent this issue, Al$_x$In$_{1-x}$As or Al$_x$In$_{1-x}$P shells with nominal Al composition fraction of x = 0.20, 0.36, or 0.53 were grown by direct vapour-solid deposition on the sidewalls of the InAs nanowires. Characterization by transmission electron microscopy revealed that the addi…
We study the optical properties of a single core-shell GaAs-AlGaAs nanowire (grown by VLS method) using the technique of micro-photoluminescence and spatially-resolved photoluminescence imaging. We observe large linear polarization anisotropy in emission and excitation of nanowires.
We investigate nanoscale local anodic oxidation (LAO) on hydrogen-intercalated graphene grown by controlled sublimation of silicon carbide (SiC). Scanning probe microscopy (SPM) was used as a lithographic and characterization tool in order to investigate the local properties of the nanofabricated structures. The anomalous thickness observed after the graphene oxidation process is linked to the impact of LAO on the substrate. Micro-Raman spectroscopy was employed to demonstrate the presence of two oxidation regimes depending on the applied bias. We show that partial and total etching of monolay…
Nanowires of Pr_0.57 Ca_0.41 Ba_0.02 MnO_3 (PCBM) (diameter ~ 80-90 nm and length ~ 3.5 mm) were synthesized by a low reaction temperature hydrothermal method. Single-phase nature of the sample was confirmed by XRD experiments. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the morphology and microstructures of the nanowires. While the bulk PCBM is known to exhibit charge order (CO) below 230 K along with a ferromagnetic transition at 110 K, SQUID measurements on the nanowires of PCBM show that the charge order is completely absent and a…
Utilizing sp3d5s* tight-binding band structure and wave functions for electrons and holes we show that acoustic phonon limited hole mobility in [110] grown silicon nanowires (SiNWs) is greater than electron mobility. The room temperature acoustically limited hole mobility for the SiNWs considered can be as high as 2500 cm2/Vs, which is nearly three times larger than the bulk acoustically limited silicon hole mobility. It is also shown that the electron and hole mobility for [110] grown SiNWs exceed that of similar diameter [100] SiNWs, with nearly two orders of magnitude difference for hole mo…
A method of growing mushroom or shell like nanostructured metal convex concave models has been worked out. Silver,copper,nickel,rhodium and Pd-Ni,Pd-Co alloy structures are reproduced as a result of self-assembly of nanowires growing on porous membranes in the course of pulse current electrodeposition. It is shown that the method allows to model not only the shell shape but also the hierarchical structure at the nano, micro and mesolevels. A 1,2 mm sized shell was grown from Pd-Ni alloy. The architecture of the models was studied by fragmentation and chemical etching. The images were obtained …
GaAs nanowires were grown by molecular beam epitaxy on Si(100) substrates covered with 5 nm SiO2. The growth was performed with As4 at low, close to stoichiometric, As4/Ga flux ratio, using Ga nanodroplets as catalyst. The nanowires are found to be in epitaxial relation to the Si substrate due to contact via pinholes through the SiO2 layer. The nanowires are up to 15 micrometers long and have diameters of about 100 nm, the catalyzing Ga nanodroplets are observed at their tops.
We report on the oxidation of self-assembled silicene nanoribbons grown on the Ag(110) surface using Scanning Tunneling Microscopy and High-Resolution Photoemission Spectroscopy. The results show that silicene nanoribbons present a strong resistance towards oxidation using molecular oxygen. This can be overcome by increasing the electric field in the STM tunnel junction above a threshold of +2.6 V to induce oxygen dissociation and reaction. The higher reactivity of the silicene nanoribbons towards atomic oxygen is observed as expected. The HR-PES confirm these observations: Even at high exposu…
We use spatially resolved micro-PL imaging at low temperature to study optical properties of two sets of CdS nanowires grown using 20 nm and 50 nm catalysts. We find that low temperature PL of single nanowires is an ideal technique to gauge the quality of a given growth run, and moreover enables the collection of detailed spatial information on single wire electronic states.
Manipulation of surface architecture of semiconducting nanowires with a control in surface polarity is one of the important objectives for nanowire based electronic and optoelectronic devices for commercialization. We report the growth of exceptionally high structural and optical quality nonpolar GaN nanowires with controlled and uniform surface morphology and size distribution, for large scale production. The role of O contamination (~1-10^5 ppm) in the surface architecture of these nanowires is investigated with the possible mechanism involved. Nonpolar GaN nanowires grown in O rich conditio…
Device applications involving topological insulators (TIs) will require the development of scalable methods for fabricating TI samples with sub-micron dimensions, high quality surfaces, and controlled compositions. Here we use Bi-, Se-, and Te-bearing metalorganic precursors to synthesize TIs in the form of nanowires. Single crystal nanowires can be grown with compositions ranging from Bi2Se3 to Bi2Te3, including the ternary compound Bi2Te2Se. These high quality nanostructured TI compounds are suitable platforms for on-going searches for Majorana Fermions.
