Advances in SRF technology over the last 40 years allowed achieving accelerating gradients ~ 50 MV/m corresponding to peak surface magnetic field close to the theoretical limit of niobium. However, the quality factor decreases significantly with increasing accelerating gradient. This decrease is expected since increasing the rf field increases the number of quasiparticles and therefore the rf losses. Recently, a new phenomenon of increase in quality factor with the accelerating gradient has been observed when SRF cavities are doped with certain non-magnetic impurities. In particular, the diffusion of nitrogen into the niobium cavities inner surface has been has been successfully implemented into the commercialization of SRF technology. The quest is still ongoing towards process development to achieve high accelerating gradient SRF structures with high quality factors for future high power accelerators. Here, we present the review of the research and development via nitrogen diffusion, materials analysis and current theoretical understanding in high Q0 SRF cavities.
The PIP-II linac will include thirty-six beta=0.61 and twenty-four beta=0.92 650 MHz 5 cell elliptical SRF cavities. Each cavity will be equipped with a tuning system consisting of a double lever slow tuner for coarse frequency tuning and a piezoelectric actuator for fine frequency tuning. The same tuner will be used for both the beta=0.61 and beta=0.92 cavities. Results of testing the cavity-tuner system for the beta=0.61 will be presented for the first time.
Radio Frequency (RF) power studies are in progress following the cryogenic commissioning of Cryomodule #1 (CM1) at Fermilab's Superconducting Radio Frequency (SRF) Accelerator Test Facility. These studies are complemented by the characterization of thermal acoustic effects on cavity microphonics manifested by apparent noisy boiling of helium involving vapor bubble and liquid vibration. The thermal acoustic measurements also consider pressure and temperature spikes which drive the phenomenon at low and high frequencies.
Nb$_3$Sn has great potential to become the material of choice for fabrication of SRF cavities. The higher critical temperature of Nb$_3$Sn potentially allows for an increased operational temperature in SRF cavities, which could enable tremendous simplification of cryogenic system, leading to significant cost reduction. We present extended characterization of a Nb$_3$Sn coated Nb cavity prepared at Cornell University. Using combination of thermometry during cavity RF measurements, and structural and analytical characterization of the cavity cutouts, we discover Nb$_3$Sn coating flaws responsibl…
We report the finding of new surface treatments that permit to manipulate the niobium resonator nitrogen content in the first few nanometers in a controlled way, and the resonator fundamental Mattis-Bardeen surface resistance and residual resistance accordingly. In particular, we find surface infusion conditions that systematically a) increase the quality factor of these 1.3 GHz superconducting radio frequency (SRF) bulk niobium resonators, up to very high gradients; b) increase the achievable accelerating gradient of the cavity compared to its own baseline with state-of-the-art surface proces…
Cool-down dynamics of superconducting accelerating cavities became particularly important for obtaining very high quality factors in SRF cavities. Previous studies proved that when cavity is cooled fast, the quality factor is higher than when cavity is cooled slowly. This has been discovered to derive from the fact that a fast cool-down allows better magnetic field expulsion during the superconducting transition. In this paper we describe the first experiment where the temperature all around the cavity was mapped during the cavity cool-down through transition temperature, proving the existence…
An increase in the quality factor of superconducting radiofrequency cavities is achieved by minimizing the surface resistance during processing steps. The surface resistance is the sum of temperature independent residual resistance and temperature/material dependent Bardeen-Cooper-Schrieffer (BCS) resistance. High temperature heat treatment usually reduces the impurities concentration from the bulk niobium, lowering the residual resistance. The BCS part can be reduced by selectively doping non-magnetic impurities. The increase in quality factor, termed as Q-rise, was observed in cavities when …
The PIP II linear accelerator includes different types of niobium SRF cavities including 650 MHz elliptical low (0.61) and high (0.92) beta cavities. The elliptical cavity surface is processed with the electropolishing method. The elliptical cavities especially the low-$β$ 650 MHz cavities showed a rough equator surface after the EP was per-formed with the standard EP conditions. This work was focused to study the effect of different EP parameters, including cathode surface area, temperature and voltage, and optimize them to improve the cavity surface.
Nb3Sn superconducting radiofrequency (SRF) cavities have substantial potential for enabling new performance capabilities for particle accelerators for high energy physics (HEP), as well as for RF cavity-based detectors for dark matter, gravitational waves, and other quantum sensing applications. Outside of HEP, Nb3Sn SRF cavities can also benefit accelerators for nuclear physics, basic energy sciences, and the industry. In this contribution to Snowmass 2021, we overview the potential, status, and outlook of Nb3Sn SRF cavities.
Thermal stability is an important parameter for the operation of the superconducting radio frequency (SRF) cavities used in particle accelerators. The rf power dissipated on the inner surface of the cavities is conducted to the helium bath cooling the outer cavity surface and the equilibrium temperature of the inner surface depends on the thermal resistance. In this manuscript, we present the results of direct measurements of thermal resistance on 1.3 GHz single cell SRF cavities made from high purity large grain and fine grain niobium as well as their rf performance for different treatments a…
An apparatus and a method are described for plasma etching of the inner surface of superconducting radio frequency (SRF) cavities. Accelerator SRF cavities are formed into a variable-diameter cylindrical structure made of bulk niobium, for resonant generation of the particle accelerating field. The etch rate non-uniformity due to depletion of the radicals has been overcome by the simultaneous movement of the gas flow inlet and the inner electrode. An effective shape of the inner electrode to reduce the plasma asymmetry for the coaxial cylindrical rf plasma reactor is determined and implemented…
Field emission is one of the key issues in superconducting RF. When present, it limits operating gradient directly or via induced heat load at 2K. In order to minimize particulate contamination of and thus field emission in the CEBAF SRF cavities during assembly, a ceramic RF window was placed very close to the accelerating cavity proper. As an unintended consequence of this, it has been possible to monitor and model field emission in the CEBAF cavities since in-tunnel operation began. The ceramic is charged by field emission to a stable voltage and then discharges. This phenomenon had to be s…
A Temperature mapping (T-map) system for Superconducting Radio Frequency (SRF) cavities consists of a thermometer array positioned precisely on an exterior cavity wall, capable of detecting small increases in temperature; therefore it is a powerful tool for research on the quality factor (Q0) of SRF cavities. A new multi-cell T-mapping system is has been developed at Cornell University. The system has nearly two thousand thermometers to cover 7-cell SRF cavities for Cornell ERL project. A new multiplexing scheme was adopted to reduce number of wires. A 1mK resolution of the temperature increas…
Trapped magnetic flux is known to be a significant contribution to the residual resistance of superconducting radio frequency (SRF) cavities. The additional losses depend strongly if the vortices are depinned by the RF. The depinning is affected by the purity of the material, and the size of the pinning centers, as well as the cavity operation frequency. One may define a depinning frequency, above which significant depinning occurs. This publication presents a derivation of the depinning frequency from experimental data. We find a depinning frequency of 673 MHz for RRR 110 niobium. On this bas…
Buffered Chemical Polishing (BCP) was the most conventional polishing method for superconducting radio frequency (SRF) Niobium (Nb) cavity surface preparation before the discovery of Electropolishing (EP), which is superior to BCP in high gradient performance. The High Field Q-slope (HFQS) is perfectly eliminated by taking the low temperature bake (LTB) post EP, which guarantees high gradient performance in EP'ed cavities. The mechanism of the HFQS is well understood for EP'ed cavities. On the other hand, there is no common consensus on the HFQS with BCP, since even BCP with LTB does not alway…
Titanium and niobium are the main materials used for the fabrication of Superconducting Radio Frequency (SRF) cavities. These two metals are usually joined , using various welding techniques, using a third material in between. This contribution focuses on the development of an innovative electron beam welding technique capable of producing a strong bond between these two different materials. Several samples are produced and tested to assess the mechanical strength at room and cryogenic temperature as well as the composition of the resulting welded joint. Also, the first units of the Single Spo…
The first heavy ion accelerator is being constructed by the rare isotope science project (RISP) launched by the Institute of Basic Science (IBS) in South Korea. Four different types of superconducting cavities were designed, and prototypes were fabricated such as a quarter wave resonator (QWR), a half wave resonator (HWR) and a single spoke resonator (SSR). One of the critical factors determining performances of the superconducting cavities is a residual resistance ratio (RRR). The RRR values essentially represent how much niobium is pure and how fast niobium can transmit heat as well. In gene…
Superconducting radio-frequency (SRF) accelerating cavities are a promising technology for compact, high-power, MeV-scale accelerators, providing continuous beam operation for a wide range of potential applications in industry, medicine, national security, and science. However, SRF cavities have traditionally been cooled using complex and expensive cryogenic infrastructure, which has been a significant obstacle in employing this powerful technology in small-scale systems. With the recent progress on high-performance Nb$_3$Sn-coated SRF cavities and the introduction of cryocoolers, which can pr…
In this letter, we present the frequency dependence of the vortex surface resistance of bulk niobium accelerating cavities as a function of different state-of-the-art surface treatments. Higher flux surface resistance per amount of trapped magnetic field - sensitivity - is observed for higher frequencies, in agreement with our theoretical model. Higher sensitivity is observed for N-doped cavities, which possess an intermediate value of electron mean-free-path, compared to 120 C and EP/BCP cavities. Experimental results from our study showed that the sensitivity has a non-monotonic trend as a f…
We investigate the effect of high temperature treatments followed by only high-pressure water rinse (HPR) of superconducting radio frequency (SRF) niobium cavities. The objective is to provide a cost effective alternative to the typical cavity processing sequence, by eliminating the material removal step post furnace treatment while preserving or improving the RF performance. The studies have been conducted in the temperature range 800-1000C for different conditions of the starting substrate: large grain and fine grain, electro-polished (EP) and centrifugal barrel polished (CBP) to mirror fini…
A new surface treatment technique for niobium (Nb) Superconducting Radio Frequency (SRF) cavities called Buffered Electropolishing (BEP) has been developed at JLab. It was found that BEP could produce the smoothest surface finish on Nb samples ever reported in the literature. Experimental results revealed that the Nb removal rate of BEP could reach as high as 4.09 um/min. This is significantly faster1 than that of the conventional electropolishing technique employing an acid mixture of HF and H2SO4. An investigation is underway to determine the optimum values for all relevant BEP parameters so…
There are many stages in the LLRF and RF system development process for any new accelerator that can take advantage of hardware emulation of the high-power RF system and RF cavities. LLRF development, bench testing, control system development and testing of installed systems must happen well before SRF cavities are available for test. The PIP-II Linac has three frequencies of SRF cavities, 162.5 MHz, 325 MHz and 650 MHz and a simple analog emulator design has been chosen that can meet the cavity bandwidth requirements, provide tuning errors to emulate Lorentz force detuning and microphonics fo…
We suggest a program to establish theoretical performance limits of srf cavities using modern theories of nonequilibrium superconductivity under a strong electromagnetic field. These theories will be used to calculate the main parameter of merit of srf cavities: the quality factor Q and its dependencies on the field amplitude, temperature and frequency, which would allow us to understand how far the srf cavity performance could be pushed from the current state of the art. Given that the quality factor is determined by multiple mechanisms operating on very different length scales, we will addre…
For many new accelerator applications, superconducting radio frequency (SRF) systems are the enabling technology. In particular for CW applications, much effort is being expended to minimize the power dissipation (surface resistance) of niobium cavities. Starting in 2009, we suggested a means of reducing the residual resistance by performing a thermal cycle [1], a procedure of warming up a cavity after initial cooldown to about 20K and cooling it down again. In subsequent studies [2], this technique was used to manipulate the residual resistance by more than a factor of 2. It was postulated th…
We present the results of from DC magnetization and penetration depth measurements of cylindrical bulk large-grain (LG) and fine-grain (FG) niobium samples used for the fabrication of superconducting radio frequency (SRF) cavities. The surface treatment consisted of electropolishing and low temperature baking as they are typically applied to SRF cavities. The magnetization data were fitted using a modified critical state model. The critical current density Jc and pinning force Fp are calculated from the magnetization data and their temperature dependence and field dependence are presented. The…
In this study, we present new insights on the origin of the high-field Q-slope in superconducting radio-frequency cavities. Consequent hydrofluoric acid rinses are used to probe the radio-frequency performance as a function of the material removal of two superconducting bulk niobium cavities prepared with low temperature nitrogen infusion. The study reveals that nitrogen infusion affects only the first few tens of nanometers below the native oxide layer. The typical high-field Q-slope behavior of electropolished cavities is indeed completely recovered after a dozen hydrofluoric acid rinses. Th…
The performance of superconducting radio-frequency (SRF) cavities depends on the niobium surface condition. Recently, various heat-treatment methods have been investigated to achieve unprecedented high quality factor (Q) and high accelerating field (E). We report the influence of a new baking process called furnace baking on the Q-E behavior of 1.3 GHz SRF cavities. Furnace baking is performed as the final step of the cavity surface treatment; the cavities are heated in a vacuum furnace for 3 h, followed by high-pressure rinsing and radio-frequency measurement. This method is simpler and poten…
A comment to the authors' SRF Conference pre-print [1] was submitted by A. Gurevich to the arXiv [2]. In this response, we show that the arguments used in the comment are not valid. [1] arXiv:1309.3239 [2] arXiv:1309.5626
We conduct the first ``light-shining-through-wall" (LSW) search for dark photons using two state-of-the-art high quality-factor superconducting radio frequency (SRF) cavities and report the results of its pathfinder run. Our new experimental setup enables improvements in sensitivity over previous searches and covers new dark photon parameter space. We design delicate calibration and measurement protocols to utilize the high-$Q$ setup at Dark SRF. Using cavities operating at $1.3 \ \text{GHz}$, we establish a new exclusion limit for kinetic mixing as small as {$ε= 1.6\times 10^{-9}$} and provid…
Recent advances in surface treatments of Niobium superconducting radio frequency (SRF) cavities have led to substantially increased Q-factors and maximum surface field. This poses theoretical challenges to identify the mechanisms responsible for such performance enhancements. We report theoretical results for the effects of inhomogeneous surface disorder on the superheating field --- the surface magnetic field above which the Meissner state is globally unstable. We find that inhomogeneous disorder, such as that introduced by infusion of Nitrogen into the surface layers of Niobium SRF cavities,…
Multipacting is seen as a performance limiting phenomenon for the superconducting radio frequency (SRF) cavities. Numerical simulations are essential to pre-empt the experimentally observed multipacting conditions. Readily available codes(e.g. FISHPACT, MULTIPACT,CST etc.) are widely used to simulate the phenomenon of multipacting in such cases. Most of the contemporary two dimensional (2D) codes are unable to detect multipacting in the elliptical cavities because they use a simplistic secondary emission model, where a constant value of emission kinetic energy of secondary electrons is assumed…
This tutorial presents in the first part the requirement for the surface preparation of RF Niobium cavities and its justification in term s of physical origin of limitation (e.g. cleanliness and field emission, influence of the surface treatments, morphology and surface damage, etc.). in the second part we discuss the different models describing the ultimate limits of SRF cavities, and present one of the possible ways to overcome Niobium monopoly toward higher performances.
Vertical test is a commonly used experimental method to qualify Superconducting Radio Frequency (SRF) cavities. Taking the experiences at Jefferson Lab (JLab) in US for example, over thousand of vertical tests have been performed on over 500 different cavities up to now [1]. Most of the tests at JLab followed the method as described in [1], but all the uncertainties of the calculated quality factors as well as the gradients were in-accurate due to the wrong algorithm used. In this paper, a first-principle method was applied to analyze the uncertainty of the data, and the results were compared …
CW magnetrons, developed for industrial heaters, but driven by an injection-locking signal were suggested to power Superconducting RF (SRF) cavities due to higher efficiency and lower cost of generated RF power per Watt than traditionally used RF sources (klystrons, IOTs, solid-state amplifiers). When the magnetrons are intended to feed Room Temperature (RT) cavities, the injected phase or frequency locking signal may provide required phase or frequency stability of the accelerating field. However, when the magnetron RF sources are intended to feed high Q-factor SRF cavities, the sources must …
In niobium superconducting radio frequency (SRF) accelerating cavities a decrease of the quality factor at lower fields - a so called \emph{low field Q slope or LFQS} - has been a long-standing unexplained effect. By extending the high $Q$ measurement techniques to ultralow fields we discover two previously unknown features of the effect: i) saturation at rf fields lower than $E_\mathrm{acc} \sim 0.1$~MV/m; ii) strong degradation enhancement by growing thicker niobium pentoxide. Our findings suggest that the LFQS may be caused by the two level systems in the natural niobium oxide on the inner …
The improvement of the quality factor Q0 of superconducting radio-frequency (SRF) cavities at medium accelerating gradients (20-25 MV/m) is important in order to reduce the cryogenic losses in continuous wave (CW) accelerators used for a variety of applications. In recent years, SRF cavities fabricated from ingot niobium have become a viable alternative to standard high-purity fine-grain Nb for the fabrication of high-performing SRF cavities with the possibility of significant cost reduction. Recent studies demonstrated the improvement of Q0 at medium field in cavities heat treated at 800-1200…
The Superconducting Quantum Materials and Systems center is developing searches for dark photons, axions and ALPs with the goal of improving upon the current state-of-the-art sensitivity. These efforts leverage on Fermi National Accelerator expertise on ultra-high quality factor superconducting radio frequency cavities combined with the center research on quantum technology. Here we focus on multiple axion searches that utilize ~1E10 quality factor superconducting radio frequency cavities and their resonant modes to enhance the production and/or detection of axions in the cavity volume. In add…
The surface resistance of an RF superconductor depends on the surface temperature, the residual resistance and various superconductor parameters, e.g. the energy gap, and the electron mean free path. These parameters can be determined by measuring the quality factor Q0 of a SRF cavity in helium-baths of different temperatures. The surface resistance can be computed from Q0 for any cavity geometry, but it is not trivial to determine the temperature of the surface when only the temperature of the helium bath is known. Traditionally, it was approximated that the surface temperature on the inner s…
A detailed study of the near-surface structure and composition of Nb, the material of choice for Superconducting Radio Frequency accelerator (SRF) cavities, is of great importance in order to understand the effects of different treatments applied during cavity production. By means of surface-sensitive techniques such as grazing incidence diffuse X-ray scattering, X-ray reflectivity and X-ray photoelectron spectroscopy, single-crystalline Nb(100) samples were investigated in and ex-situ during annealing in UHV as well as in nitrogen atmospheres with temperatures and pressures similar to the one…
