Massive multiple-input multiple-output (MIMO) is a key technology for 5G wireless communications with a promise of significant capacity increase. The use of low-resolution data converters is crucial for massive MIMO to make the overall transmission as cost- and energy-efficient as possible. In this work, we consider a downlink millimeter-wave (mmWave) transmission scenario, where multiple users are served simultaneously by massive MIMO with one-bit digital-to-analog (D/A) converters. In particular, we propose a novel precoder design based on signal-to-leakage-plus-noise ratio (SLNR), which minimizes energy leakage into undesired users while taking into account impairments due to nonlinear one-bit quantization. We show that well-known regularized zero-forcing (RZF) precoder is a particular version of the proposed SLNR-based precoder, which is obtained when quantization impairments are totally ignored. Numerical results underscore significant performance improvements along with the proposed SLNR-based precoder as compared to either RZF or zero-forcing (ZF) precoders.
Signal-to-leakage-and-noise ratio (SLNR) is a promising criterion for linear precoder design in multi-user (MU) multiple-input multiple-output (MIMO) systems. It decouples the precoder design problem and makes closed-form solution available. In this letter, we present a new linear precoding scheme by slightly relaxing the SLNR maximization for MU-MIMO systems with multiple data streams per user. The precoding matrices are obtained by a general form of simultaneous diagonalization of two Hermitian matrices. The new scheme reduces the gap between the per-stream effective channel gains, an inhere…
In this paper, we propose an enhanced leakage-based precoding scheme, i.e., layer signal to leakage plus noise ratio (layer SLNR) scheme, for multi-user multi-layer MIMO systems. Specifically, the layer SLNR scheme incorporates the MIMO receiver structure into the precoder design procedure, which makes the formulation of signal power and interference / leakage power more accurate. Besides, the layer SLNR scheme not only takes into account the inter-layer interference from different users, but also takes care of the inter-layer interference from the same user which is usually assumed to be zero…
We consider a downlink multiuser multiple-input multiple output (MIMO) system employing regularized zero-forcing (RZF) precoding. We derive the asymptotic signal-to-leakage-plus-noise ratio (SLNR) as both the number of antennas and the number of users go to infinity at a fixed ratio. Focusing on the symmetric uncorrelated channels, we show that the SLNR is asymptotically equal to signal-to-interference-plus-noise ratio (SINR) which allows us to optimize the user loading for spectral efficiency. The results show that the optimal user loading varies depending on the channel signal-to-noise ratio…
The two-stage precoding has been proposed to reduce the overhead of both the channel training and the channel state information (CSI) feedback for the massive multiple-input multiple-output (MIMO) system. But the overlap of the angle-spreading-ranges (ASR) for different user clusters may seriously degrade the performance of the two-stage precoding. In this letter, we propose one ASR overlap mitigating scheme through the base station (BS) selection. Firstly, the BS selection is formulated as a sum signal-to-interference-plus-noise ratio (SINR) maximization problem. Then, the problem is solved b…
Relay-aided transmission is envisioned as a key strategy to combat severe path loss and link blockages emerging as unique challenges in millimeter-wave (mmWave) communications. This work considers a relay-aided multiuser mmWave communications scenario aiming at maximizing the sum rate through optimal transmit and relay precoder design. We propose a novel joint precoder design strategy, which exploits weighted minimum mean-square error (WMMSE) using its equivalency to sum-rate maximization. We obtain closed form expressions of transmit and relay precoders, and propose to compute them through al…
This paper focuses on the design of low complexity hybrid analog/digital precoding and diversity combining in millimeter wave (mmWave) Internet of things (IoT) systems. Firstly, by exploiting the sparseness property of the mmWave in the angular domain, we propose a spatial lobes division (SLD) to group the total paths of the mmWave channel into several spatial lobes, where the paths in each spatial lobe form a low-rank sub-channel. Secondly, based on the SLD operation, we propose a low complexity hybrid precoding scheme, named HYP-SLD. Specifically, for each low-rank sub-channel, we formulate …
Millimeter wave (mmWave) massive MIMO can achieve orders of magnitude increase in spectral and energy efficiency, and it usually exploits the hybrid analog and digital precoding to overcome the serious signal attenuation induced by mmWave frequencies. However, most of hybrid precoding schemes focus on the full-array structure, which involves a high complexity. In this paper, we propose a near-optimal iterative hybrid precoding scheme based on the more realistic subarray structure with low complexity. We first decompose the complicated capacity optimization problem into a series of ones easier …
Generalized spatial modulation (GenSM) aided millimeter wave (mmWave) multiple-input multiple-output (MIMO) has recently received substantial academic attention. However, due to the insufficient exploitation of the transmitter's knowledge of the channel state information (CSI), the achievable rates of state-of-the-art GenSM-aided mmWave MIMO systems are far from being optimal. Against this background, a novel analog precoding scheme is proposed in this paper to improve the spectral efficiency (SE) of conventional GenSM-aided mmWave MIMOs. More specifically, we firstly manage to lower-bound the…
Large propagation path loss and limited scattering of millimeter wave (mmwave) channels create new challenges for physical layer signal processing. Hence, in this article, we propose a photonic hybrid precoding model for mmwave radio-over-fiber systems that overcomes hardware constraints on radio frequency precoding. With help of silicon photonic integrated circuits (Si-PICs), the photonic precoding strategy combats the large losses of mmwave and mitigates inter-user interference. Simulation results show that the proposed model can offer significant coding gains over conventional precoding sys…
To perform multi-user multiple-input and multiple-output transmission in millimeter-wave(mmWave) cellular systems, the high-dimensional channels need to be estimated for designing the multi-user precoder. Conventional grid-based compressed sensing (CS) methods for mmWave channel estimation suffer from the basis mismatch problem, which prevents accurate channel reconstruction and degrades the precoding performance. This paper formulates mmWave channel estimation as an Atomic Norm Minimization (ANM) problem. In contrast to grid-based CS methods which use discrete dictionaries, ANM uses a continu…
Hybrid precoding is a cost-effective approach to support directional transmissions for millimeter wave (mmWave) communications. While existing works on hybrid precoding mainly focus on single-user single-carrier transmission, in practice multicarrier transmission is needed to combat the much increased bandwidth, and multiuser MIMO can provide additional spatial multiplexing gains. In this paper, we propose a new hybrid precoding structure for multiuser OFDM mmWave systems, which greatly simplifies the hybrid precoder design and is able to approach the performance of the fully digital precoder.…
Millimeter wave (mmWave) signals experience orders-of-magnitude more pathloss than the microwave signals currently used in most wireless applications. MmWave systems must therefore leverage large antenna arrays, made possible by the decrease in wavelength, to combat pathloss with beamforming gain. Beamforming with multiple data streams, known as precoding, can be used to further improve mmWave spectral efficiency. Both beamforming and precoding are done digitally at baseband in traditional multi-antenna systems. The high cost and power consumption of mixed-signal devices in mmWave systems, how…
Hybrid analog/digital precoding offers a compromise between hardware complexity and system performance in millimeter wave (mmWave) systems. This type of precoding allows mmWave systems to leverage large antenna array gains that are necessary for sufficient link margin, while permitting low cost and power consumption hardware. Most prior work has focused on hybrid precoding for narrowband mmWave systems, with perfect or estimated channel knowledge at the transmitter. MmWave systems, however, will likely operate on wideband channels with frequency selectivity. Therefore, this paper considers wid…
Millimeter wave (mmWave) MIMO will likely use hybrid analog and digital precoding, which uses a small number of RF chains to avoid energy consumption associated with mixed signal components like analog-to-digital components not to mention baseband processing complexity. However, most hybrid precoding techniques consider a fully-connected architecture requiring a large number of phase shifters, which is also energyintensive. In this paper, we focus on the more energy-efficient hybrid precoding with sub-connected architecture, and propose a successive interference cancelation (SIC)-based hybrid …
Hybrid analog/digital precoding architectures can address the trade-off between achievable spectral efficiency and power consumption in large-scale MIMO systems. This makes it a promising candidate for millimeter wave systems, which require deploying large antenna arrays at both the transmitter and receiver to guarantee sufficient received signal power. Most prior work on hybrid precoding focused on narrowband channels and assumed fully-connected hybrid architectures. MmWave systems, though, are expected to be wideband with frequency selectivity. In this paper, a closed-form solution for fully…
Millimeter-wave (mmWave) communication is considered as an indispensable technique for the next-generation backhaul/fronthaul network thanks to its large transmission bandwidth. Especially for heterogeneous network (HetNet), the mmWave full-dimension (FD)-MIMO is exploited to establish the backhaul/fronthaul link between phantom-cell base stations (BSs) and macro-cell BSs, where an efficient precoding is prerequisite. Against this background, this paper proposes a principle component analysis (PCA)-based hybrid precoding for wideband mmWave MIMO backhaul/fronthaul channels. We first propose an…
Hybrid precoding design can be challenging for broadband millimeter-wave (mmWave) massive MIMO due to the frequency-flat analog precoder in radio frequency (RF). Prior broadband hybrid precoding work usually focuses on fully-connected array (FCA), while seldom considers the energy-efficient partially-connected subarray (PCS) including the fixed subarray (FS) and dynamic subarray (DS). Against this background, this paper proposes a machine learning based broadband hybrid precoding for mmWave massive MIMO with DS. Specifically, we first propose an optimal hybrid precoder based on principal compo…
The application of hybrid precoding in millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems has been proved effective for reducing the number of radio frequency (RF) chains. However, the maximum number of independent data streams is conventionally restricted by the number of RF chains, which leads to limiting the spatial multiplexing gain. To further improve the achievable spectral efficiency (SE), in this paper we propose a novel generalized spatial modulation (GenSM) aided mmWave MIMO system to convey an extra data stream via the index of the active antennas group, while no…
Hybrid precoding is a promising technique for mmWave massive MIMO systems, as it can considerably reduce the number of required radio-frequency (RF) chains without obvious performance loss. However, most of the existing hybrid precoding schemes require a complicated phase shifter network, which still involves high energy consumption. In this paper, we propose an energy-efficient hybrid precoding architecture, where the analog part is realized by a small number of switches and inverters instead of a large number of high-resolution phase shifters. Our analysis proves that the performance gap bet…
Due to the high cost and low energy efficiency of the dedicated radio frequency (RF) chains, the number of RF chains in a millimeter wave (mmWave) multiple-input multiple-output (MIMO) system is usually limited from a practical point of view. In this case, the maximum number of independent data streams is also restricted by the number of RF chains, which consequently leads to limiting the potentially attainable spatial multiplexing gain. In order to address this issue, in this paper, a novel generalized spatial modulation (GenSM) aided mmWave MIMO system is proposed, which enables the transmis…
Power consumption of multi-user (MU) precoding is a major concern in all-digital massive MU multiple-input multiple-output (MIMO) base-stations with hundreds of antenna elements operating at millimeter-wave (mmWave) frequencies. We propose to replace part of the linear Wiener filter (WF) precoding matrix by a finite-alphabet WF precoding (FAWP) matrix, which enables the use of low-precision hardware that consumes low power and area. To minimize the performance loss of our approach, we present methods that efficiently compute FAWP matrices that best mimic the WF precoder. Our results show that …
Massive multi-user multiple-input multiple-output (MU-MIMO) wireless systems operating at millimeter-wave (mmWave) frequencies enable simultaneous wideband data transmission to a large number of users. In order to reduce the complexity of MU precoding in all-digital basestation architectures, we propose a two-stage precoding architecture that first performs precoding using a sparse matrix in the beamspace domain, followed by an inverse fast Fourier transform that converts the result to the antenna domain. The sparse precoding matrix requires a small number of multipliers and enables regular ha…
Antenna arrays will be an important ingredient in millimeter wave (mmWave) cellular systems. A natural application of antenna arrays is simultaneous transmission to multiple users. Unfortunately, the hardware constraints in mmWave systems make it difficult to apply conventional lower frequency multiuser MIMO precoding techniques at mmWave. This paper develops low complexity hybrid analog/digital precoding for downlink multiuser mmWave systems. Hybrid precoding involves a combination of analog and digital processing that is inspired by the power consumption of complete radio frequency and mixed…
Millimeter wave (mmWave) cellular systems will enable gigabit-per-second data rates thanks to the large bandwidth available at mmWave frequencies. To realize sufficient link margin, mmWave systems will employ directional beamforming with large antenna arrays at both the transmitter and receiver. Due to the high cost and power consumption of gigasample mixed-signal devices, mmWave precoding will likely be divided among the analog and digital domains. The large number of antennas and the presence of analog beamforming requires the development of mmWave-specific channel estimation and precoding a…
Channel estimation is challenging for millimeter-wave (mmWave) massive MIMO with hybrid precoding, since the number of radio frequency (RF) chains is much smaller than that of antennas. Conventional compressive sensing based channel estimation schemes suffer from severe resolution loss due to the channel angle quantization. To improve the channel estimation accuracy, we propose an iterative reweight (IR)-based super-resolution channel estimation scheme in this paper. By optimizing an objective function through the gradient descent method, the proposed scheme can iteratively move the estimated …
In this paper, a combination of Space Time Block Coded Spatial Modulation with Hybrid Analog-Digital Beamforming (STBC-SM-HBF) for Millimeter-wave (mmWave) communications is proposed in order to take advantage of the merits of Spatial Modulation (SM), Space-Time Block Codes (STBC), Analog Beamforming (ABF), and digital precoding techniques while avoiding their drawbacks. This proposed system benefits from the multiplexing gain of SM, from the transmit diversity gain of STBC, and from the Signal-to-Noise Ratio (SNR) gain of the beamformer. The simulation results demonstrate that the Zero Forcin…
Hybrid precoding is a cost-efficient technique for millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) communications. This paper proposes a deep learning approach by using a distributed neural network for hybrid analog-and-digital precoding design with limited feedback. The proposed distributed neural precoding network, called DNet, is committed to achieving two objectives. First, the DNet realizes channel state information (CSI) compression with a distributed architecture of neural networks, which enables practical deployment on multiple users. Specifically, this neural ne…
Hybrid analog/digital precoding allows millimeter wave MIMO systems to leverage large antenna array gains while permitting low cost and power consumption hardware. Most prior work has focused on hybrid precoding for narrow-band mmWave systems. MmWave systems, however, will likely operate on wideband channels with frequency selectivity. Therefore, this paper considers frequency selective hybrid precoding with RF beamforming vectors taken from a quantized codebook. For this system, a low-complexity yet near-optimal greedy algorithm is developed for the design of the hybrid analog/digital precode…
Millimeter wave (mmWave) systems will likely employ large antenna arrays at both the transmitters and receivers. A natural application of antenna arrays is simultaneous transmission to multiple users, which requires multi-user precoding at the transmitter. Hardware constraints, however, make it difficult to apply conventional lower frequency MIMO precoding techniques at mmWave. This paper proposes and analyzes a low complexity hybrid analog/digital beamforming algorithm for downlink multi-user mmWave systems. Hybrid precoding involves a combination of analog and digital processing that is moti…
In this paper, the performance of multi-user Multiple-Input Multiple-Output (MIMO) systems is evaluated in terms of SINR and capacity. We focus on the case of a downlink single-cell scenario where different precoders have been studied. Among the considered precoders, we range from different Grid of Beams (GoB) optimization approaches to linear precoders (e.g., matched filtering and zero forcing). This performance evaluation includes imperfect channel estimation, and is carried out over two realistic mmWave 5G propagation channels, which are simulated following either the measurement campaign d…
The cell-free MIMO concept relying on hybrid precoding constitutes an innovative technique capable of dramatically increasing the network capacity of millimeter-wave (mmWave) communication systems. It dispenses with the cell boundary of conventional multi-cell MIMO systems, while drastically reducing the power consumption by limiting the number of radio frequency (RF) chains at the access points (APs). In this paper, we aim for maximizing the weighted sum rate (WSR) of mmWave cell-free MIMO systems by conceiving a low-complexity hybrid precoding algorithm. We formulate the WSR optimization pro…
User-centric (UC) based cell-free (CF) structures can provide the benefits of coverage enhancement for millimeter wave (mmWave) multiple input multiple output (MIMO) systems, which is regarded as the key technology of the reliable and high-rate services. In this paper, we propose a new beam selection scheme and precoding algorithm for the UC CF mmWave MIMO system, where a weighted sum-rate maximization problem is formulated. Since the joint design of beam selection and precoding is non-convex and tractable with high complexity, this paper designs the beam selection and precoding separately. Pa…
In this paper, we study hierarchical codebook design for channel estimation in millimeter-wave (mmWave) communications with a hybrid precoding structure. Due to the limited saturation power of mmWave power amplifier (PA), we take the per-antenna power constraint (PAPC) into consideration. We first propose a metric, i.e., generalized detection probability (GDP), to evaluate the quality of \emph{an arbitrary codeword}. This metric not only enables an optimization approach for mmWave codebook design, but also can be used to compare the performance of two different codewords/codebooks. To the best…
Hybrid digital analog (HDA) beamforming has attracted considerable attention in practical implementation of millimeter wave (mmWave) multiuser multiple-input multiple-output (MU-MIMO) systems due to its low power consumption with respect to its digital baseband counterpart. The implementation cost, performance, and power efficiency of HDA beamforming depends on the level of connectivity and reconfigurability of the analog beamforming network. In this paper, we investigate the performance of two typical architectures for HDA MU-MIMO, i.e., the fully-connected (FC) architecture where each RF ant…
Millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) with hybrid precoding is a promising technique for the future 5G wireless communications. Due to a large number of antennas but a much smaller number of radio frequency (RF) chains, estimating the high-dimensional mmWave massive MIMO channel will bring the large pilot overhead. To overcome this challenge, this paper proposes a super-resolution channel estimation scheme based on two-dimensional (2D) u- nitary ESPRIT algorithm. By exploiting the angular sparsity of mmWave channels, the continuously distributed angle of arriva…
Millimeter wave (mmWave) communication is a promising solution for coping with the ever-increasing mobile data traffic because of its large bandwidth. To enable a sufficient link margin, a large antenna array employing directional beamforming, which is enabled by the availability of channel state information at the transmitter (CSIT), is required. However, CSIT acquisition for mmWave channels introduces a huge feedback overhead due to the typically large number of transmit and receive antennas. Leveraging properties of mmWave channels, this paper proposes a precoding strategy which enables a f…
With the congestion of the sub-6 GHz spectrum, the interest in massive multiple-input multiple-output (MIMO) systems operating on millimeter wave spectrum grows. In order to reduce the power consumption of such massive MIMO systems, hybrid analog/digital transceivers and application of low-resolution digital-to-analog/analog-to-digital converters have been recently proposed. In this work, we investigate the energy efficiency of quantized hybrid transmitters equipped with a fully/partially-connected phase-shifting network composed of active/passive phase-shifters and compare it to that of quant…
This work investigates the effect of double intelligent reflecting surface (IRS) in improving the spectrum efficient of multi-user multiple-input multiple-output (MIMO) network operating in the millimeter wave (mmWave) band. Specifically, we aim to solve a weighted sum rate maximization problem by jointly optimizing the digital precoding at the transmitter and the analog phase shifters at the IRS, subject to the minimum achievable rate constraint. To facilitate the design of an efficient solution, we first reformulate the original problem into a tractable one by exploiting the majorization-min…
The potential of using millimeter-wave (mmWave) to encounter the current bandwidth shortage has motivated packing more antenna elements in the same physical size which permits the advent of massive multiple-input-multiple-output (MIMO) for mmWave communication. However, with increasing number of antenna elements, the ability of allocating a single RF-chain per antenna becomes infeasible and unaffordable. As a cost-effective alternative, the design of hybrid precoding has been considered where the limited-scattering signals are captured by a high-dimensional RF precoder realized by an analog ph…
As a key enabling technology for 5G wireless, millimeter wave (mmWave) communication motivates the utilization of large-scale antenna arrays for achieving highly directional beamforming. However, the high cost and power consumption of RF chains stands in the way of adoption of the optimal fullydigital precoding in large-array systems. To reduce the number of RF chains while still maintaining the spatial multiplexing gain of large-array, hybrid precoding architecture has been proposed for mmWave systems and received considerable interest in both industry and academia. However, the optimal hybri…
Hybrid analog/digital precoding is a promising technology to cut down hardware cost in massive multi-input multi-output (MIMO) systems at millimeter wave frequencies. In this letter, we propose a joint beam selection scheme for analog domain precoding under discrete lens array. By considering channel correlation among users, the proposed scheme is able to avoid inter-user interference and maximize system sum rate. Moreover, a bio-inspired ant colony optimization-based algorithm is proposed to obtain a near-optimal solution with dramatically reduced computational complexity. Finally, simulation…
Millimeter-wave (mmWave) communications plays an important role for future cellular networks because of the vast amount of spectrum available in the underutilized mmWave frequency bands. To overcome the huge free space omnidirectional path loss in those frequency bands, the deployment of a very large number of antenna elements at the base station is crucial. The complexity, power consumption and costs resulting from the large number of antenna elements can be reduced by limiting the number of RF chains. This leads to hybrid precoding and combining, which, in contrast to the traditional fully d…
Multicast beamforming is known to improve spectral efficiency. However, its benefits and challenges for hybrid precoders design in millimeter-wave (mmWave) systems remain understudied. To this end, this paper investigates the first joint design of hybrid transmit precoders (with an arbitrary number of finite-resolution phase shifts) and receive combiners for mmWave multi-group multicasting. Our proposed design leverages semidefinite relaxation (SDR), alternating optimization and Cholesky matrix factorization to sequentially optimize the digital/analog precoders at the transmitter and the combi…
In millimeter wave (mmWave) systems, antenna architecture limitations make it difficult to apply conventional fully digital precoding techniques but call for low cost analog radio-frequency (RF) and digital baseband hybrid precoding methods. This paper investigates joint RF-baseband hybrid precoding for the downlink of multiuser multi-antenna mmWave systems with a limited number of RF chains. Two performance measures, maximizing the spectral efficiency and the energy efficiency of the system, are considered. We propose a codebook based RF precoding design and obtain the channel state informati…
Non-orthogonal multiple access (NOMA) has been recently considered in millimeter-wave (mmWave) massive MIMO systems to further enhance the spectrum efficiency. In addition, simultaneous wireless information and power transfer (SWIPT) is a promising solution to maximize the energy efficiency. In this paper, for the first time, we investigate the integration of SWIPT in mmWave massive MIMO-NOMA systems. As mmWave massive MIMO will likely use hybrid precoding (HP) to significantly reduce the number of required radio-frequency (RF) chains without an obvious performance loss, where the fully digita…
Hybrid precoding design is challenging for millimeter-wave (mmWave) massive MIMO. Most prior hybrid precoding schemes are designed to maximize the sum spectral efficiency (SSE), while seldom investigate the bit-error-rate (BER). Therefore, we propose an over-sampling codebook (OSC)-based hybrid minimum sum-mean-square-error (min-SMSE) precoding scheme for mmWave multi-user three-dimensional (3D)-MIMO systems to optimize the BER, where multi-user transmission with multiple data streams for each user is considered. Specifically, given the effective baseband channel consisting of the real channel…
Non-orthogonal multiple access (NOMA) and millimeter wave (mmWave) are two key enabling technologies for the fifth-generation (5G) mobile networks and beyond. In this paper, we consider mmWave NOMA systems with max-min fairness constraints. On the one hand, existing beamforming designs aiming at maximizing the spectrum efficiency (SE) are unsuitable for the NOMA systems with fairness in this paper. On the other hand, previous work on about mmWave NOMA mostly depends on full knowledge of channel state information (CSI) which is extremely difficult to obtain accurately in mmWave communication sy…
In this paper, we consider the amplify-and-forward relay networks in mmWave systems and propose a hybrid precoder/combiner design approach. The phase-only RF precoding/combining matrices are first designed to support multi-stream transmission, where we compensate the phase for the eigenmodes of the channel. Then, the baseband precoders/combiners are performed to achieve the maximum mutual information. Based on the data processing inequality for the mutual information, we first jointly design the baseband source and relay nodes to maximize the mutual information before the destination baseband …
A variable-phase-shifter (VPS) architecture with hybrid precoding for mixture use of phase shifters and switches, is proposed for millimeter wave massive multiple-input multiple-output communications. For the VPS architecture, a hybrid precoding design (HPD) scheme, called VPS-HPD, is proposed to optimize the phases according to the channel state information by alternately optimizing the analog precoder and digital precoder. To reduce the computational complexity of the VPS-HPD scheme, a low-complexity HPD scheme for the VPS architecture (VPS-LC-HPD) including alternating optimization in three…
This paper investigates the joint design of hybrid transmit precoder and analog receive combiners for single-group multicasting in millimeter-wave systems. We propose LB-GDM, a low-complexity learning-based approach that leverages gradient descent with momentum and alternating optimization to design (i) the digital and analog constituents of a hybrid transmitter and (ii) the analog combiners of each receiver. In addition, we also extend our proposed approach to design fully-digital precoders. We show through numerical evaluation that, implementing LB-GDM in either hybrid or digital precoders a…
This paper investigates the hybrid precoding design for millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems with finite-alphabet inputs. The mmWave MIMO system employs partially-connected hybrid precoding architecture with dynamic subarrays, where each radio frequency (RF) chain is connected to a dynamic subset of antennas. We consider the design of analog and digital precoders utilizing statistical and/or mixed channel state information (CSI), which involve solving an extremely difficult problem in theory: First, designing the optimal partition of antennas over RF chains is…
This paper investigates dual-layer non-orthogonally superimposed transmissions for industrial internet of things (IoT) millimeter-wave communications. Essentially, the overlayer is a ubiquitous multicast signal devised to serve all the devices in coverage with a common message, i.e., critical control packet. The underlayer is a composite signal that consists of private unicast messages. Due to safety implications, it is critical that all devices can decode the multicast information. To ensure this requirement, we jointly optimize the hybrid precoder, analog combiners, power allocation, and fai…
Outdoor-to-indoor communications in millimeter-wave (mmWave) cellular networks have been one challenging research problem due to the severe attenuation and the high penetration loss caused by the propagation characteristics of mmWave signals. We propose a viable solution to implement the outdoor-to-indoor mmWave communication system with the aid of an active intelligent transmitting surface (active-ITS), where the active-ITS allows the incoming signal from an outdoor base station (BS) to pass through the surface and be received by the indoor user-equipments (UEs) after shifting its phase and m…
In general, the zero-forcing (ZF) precoding suffers from a severe receive signal-to-noise ratio (SNR) degradation in the high interference regime. However, recent evidences from realistic measurements demonstrated that millimeter wave (mmWave) systems are mainly noise-limited as high gain antennas behave as spatial filters to the interference signal. This makes ZF precoding equally attractive as that of other linear precoding counterparts. Considering ZF precoding, this paper aims to derive a lower bound on the sum-rate achieved by a decremental beam selection (BS) algorithm in a beamspace MIM…
The uplink from a very small aperture terminal (VSAT) towards multiple satellites is considered, in this paper. VSATs can be equipped with multiple antennas, allowing parallel transmission to multiple satellites. A low-complexity precoder based on imperfect positional information of the satellites is presented. The probability distribution of the position uncertainty and the statistics of the channel elements are related by the characteristic function of the position uncertainty. This knowledge is included in the precoder design to maximize the mean signal-to-leakage-and-noise ratio (SLNR) at …
In this paper, we develop a low-complexity channel estimation for hybrid millimeter wave (mmWave) systems, where the number of radio frequency (RF) chains is much less than the number of antennas equipped at each transceiver. The proposed mmWave channel estimation algorithm first exploits multiple frequency tones to estimate the strongest angle-of-arrivals (AoAs) at both base station (BS) and user sides for the design of analog beamforming matrices. Then all the users transmit orthogonal pilot symbols to the BS along the directions of the estimated strongest AoAs in order to estimate the chann…
In millimeter-wave (mmWave) MIMO systems, while a hybrid digital/analog precoding structure offers the potential to increase the achievable rate, it also faces the challenge of the need of a low-complexity design. In specific, the hybrid precoding may require matrix operations with a scale of antenna size, which is generally large in mmWave communication. Moreover, the channel estimation is also rather time consuming due to the large number of antennas at both Tx/Rx sides. In this paper, a low-complexity hybrid precoding and channel estimation approach is proposed. In the channel estimation ph…
