Real-time stress evolution in a graphite-based lithium-ion battery negative-electrode during electrolyte wetting and electrochemical cycling is measured through wafer-curvature method. Upon electrolyte addition, the composite electrode rapidly develops compressive stress of the order of 1-2 MPa due to binder swelling; upon continued exposure, the stress continues to evolve towards an apparent plateau. During electrochemical intercalation at a slow rate, the compressive stress increases with the electrode's state-of-charge, reaching a maximum value of 10 - 12 MPa. There appears to be an approximate correlation between the rate of stress rise and the staging behavior of the lithiated graphite. De-intercalation at a slow rate results in a similar linear decrease in electrode stress. Tensile stress of a few MPa develops at the end of deintercalation in the first few cycles, after which the electrode remains under compressive stress only. Although higher peak stresses are seen at high C-rates, the dependence appears to be relatively weak (up to 5C). These measurements reveal, for the first time, the nature of stress evolution in practical lithium-ion-battery electrodes and provide useful data to quantify the driving force for mechanical damage that accrues in composite electrodes upon repeated cycling. While the reported results can serve as reference for calibrating theoretical and computational models to predict electrode stress and damage evolution, the methodology demonstrated can be used to measure stresses and characterize fatigue damage in any composite lithium-ion-battery electrode as well as optimize its microstructure to mitigate stress-related damage mechanisms.
LixMn2O4 is an important cathode material for the Li ion battery. During battery charging, the stoichiometry x varies continuously from 1 to zero and on discharging it varies from zero to one. The cubic lattice constant a of LixMn2O4 depends on the value of x and the variation of a with x has important consequences for the battery performance. In this paper, we use a Madelung-Buckingham model to study this variation and compare the results with experimental data on LixMn2O4
Li-ion rechargeable batteries have enabled the wireless revolution transforming global communication. Future challenges, however, demands distributed energy supply at a level that is not feasible with the current energy-storage technology. New materials, capable of providing higher energy density are needed. Here we report a new class of lithium-ion batteries based on a graphene ink anode and a lithium iron phosphate cathode. By carefully balancing the cell composition and suppressing the initial irreversible capacity of the anode, we demonstrate an optimal battery performance in terms of spec…
We have studied low-temperature magnetic properties as well as high-temperature lithium ion diffusion in the battery cathode materials LixNi1/3Co1/3Mn1/3O2 by the use of muon spin rotation/relaxation. Our data reveal that the samples enter into a 2D spin-glass state below TSG=12 K. We further show that lithium diffusion channels become active for T>Tdiff=125 K where the Li-ion hopping-rate [nu(T)] starts to increase exponentially. Further, nu(T) is found to fit very well to an Arrhenius type equation and the activation energy for the diffusion process is extracted as Ea=100 meV.
Distributions of potential and lithium content inside lithium ion batteries highly affects their performance and durability. An increased heterogeneity of the lithium distribution is expected in thick electrodes with high energy densities or cycling at high currents. To optimize electrodes and cells designs, it is crucial to probe lithium concentration gradients across the depth of the electrode, but also to predict their occurrence and magnitude as a function of materials properties. Here, we follow the lithium distribution across a $80~μm$ thick porous graphite electrode using a $1~μm$ focus…
In this paper, Al-Cu-Fe quasicrystal alloy was used as anode material of lithium-ion batteries. The first specific discharge capacity of quasicrystal was 204mAh/g. Cyclic voltammetry showed that oxidation peak of Al-Cu-Fe quasicrystal was at about 1.4V. The reduction peak was at 0.3V. Al-Cu-Fe quasicrystal have higher Li-ion diffusion impedance and Warburg in the first cycle. X-ray diffraction analysis demonstrate that Li atom enter into quasicrystal structure can not fully leave quasicrytal during first charge/discharge cycle which induce the irreversible capacity.
Long-term durability is a major obstacle limiting the widespread use of lithium ion batteries (LIBs) in heavy-duty applications and others demanding extended lifetime. As one of the root causes of degradation and failure of battery performance, the electrode failure mechanisms are still unknown. Here, we reveal the fundamental fracture mechanisms of single-crystal silicon electrodes over extended lithiation/delithiation cycles, using electrochemical testing, microstructure characterization, fracture mechanics, and finite element analysis. Anisotropic lithium invasion causes crack initiation pe…
Accurate identification of chemical phases associated with the electrode and solid electrolyte interphase (SEI) is critical for understanding and controlling interfacial degradation mechanisms in lithium containing battery systems. To study these critical battery materials and interfaces X ray photoelectron spectroscopy (XPS) is a widely used technique that provides quantitative chemical insights. However, due to the fact that a majority of chemical phases relevant to battery interfaces are poor electronic conductors, phase identification that relies primarily on absolute XPS core level bindin…
We report the synthesis of a graphene-sulfur composite material by wrapping polyethyleneglycol (PEG) coated submicron sulfur particles with mildly oxidized graphene oxide sheets decorated by carbon black nanoparticles. The PEG and graphene coating layers are important to accommodating volume expansion of the coated sulfur particles during discharge, trapping soluble polysulfide intermediates and rendering the sulfur particles electrically conducting. The resulting graphene-sulfur composite showed high and stable specific capacities up to ~600mAh/g over more than 100 cycles, representing a prom…
The current rechargeable battery technologies have a failure in their performance at high pressure and temperature. In this article, we have brought theoretical insights on using boron nitride flakes as a protecting layer for a lithium-ion battery device and extended its application for a spin-dependent photon emission device. Hence, the electronic properties of pristine and lithium-doped hydrogen-edged boron nitride flakes have been studied by the first principle density functional theory calculations. In this study, we have discussed the stability, adsorption energies, bond lengths, electron…
Electrostatic energy (Madelung energy) is a major constituent of the cohesive energy of ionic crystals. Several physicochemical properties of these materials depend on the response of their electrostatic energy to a variety of applied thermal, electrical and mechanical stresses. In the present study, a method has been developed based on Ewalds technique, to compute the electrostatic energy arising from ion-ion interactions in ionic crystals like LixMn2O4 with variable stoichiometries and mixed valencies. An interesting application of this method in computing the voltages of lithium ion batteri…
Lithium (Li) metal anodes are essential for developing next-generation high-energy-density batteries. However, Li dendrite/whisker formation caused short-circuiting issue and short cycle life have prevented lithium metal from being viably used in rechargeable batteries. Numerous works have been done to study how to regulate the Li growth in electrochemical cycling by using external stacking forces. While it is widely agreed that stack pressure positively affects the lithium plating/stripping process, the optimized pressure range provided by different works varies greatly because of the differe…
Metal fluoride and oxides can store multiple lithium-ions through conversion chemistry to enable high energy-density lithium-ion batteries. However, their practical applications have been hindered by an unusually large voltage hysteresis between charge and discharge voltage-profiles and the consequent low energy efficiency (< 80%). The physical origins of such hysteresis are rarely studied and poorly understood. Here we employ in situ X-ray absorption spectroscopy (XAS), transmission electron microscopy (TEM), density-functional-theory (DFT) calculations, and galvanostatic intermittent titrati…
In this report, future performance demands of batteries for various vehicular applications are modeled. Vehicles ranging in size from electric bikes to heavy trucks are assessed using driving cycle data which allows key performance parameters such as desired range (km), specific energy of the battery (Wh/Kg), cycle life requirement and expected price per unit capacity (Euro/kWh) to be calculated. These projected performance requirements are compared with the outputs for three existing Li-ion batteries (namely (a) Kokam based high specific energy source (b) A123 based high power energy source a…
We review recent ab initio molecular dynamics studies of electrode/electrolyte interfaces in lithium ion batteries. Our goals are to introduce experimentalists to simulation techniques applicable to models which are arguably most faithful to experimental conditions so far, and to emphasize to theorists that the inherently interdisciplinary nature of this subject requires bridging the gap between solid and liquid state perspectives. We consider liquid ethylene carbonate (EC) decomposition on lithium intercalated graphite, lithium metal, oxide-coated graphite, and spinel manganese oxide surfaces…
The biggest challenge for the commercialization of layered structured nickel rich lithium transition metal oxide cathode is the capacity and voltage fading. Resolving this problem over the years follows an incremental progress. In this work, we report our finding of totally a new approach to revolutionize the cycle stability of aggregated cathode particles for lithium ion battery at both room and elevated temperatures. We discover that infusion of a solid electrolyte into the grain boundaries of the cathode secondary particles can dramatically enhance the capacity retention and voltage stabili…
We present an incisive spectroscopic technique for directly probing redox orbitals based on bulk electron momentum density measurements via high-resolution x-ray Compton scattering. Application of our method to spinel LixMn2O4, a lithium ion battery cathode material, is discussed. The orbital involved in the lithium insertion and extraction process is shown to mainly be the oxygen 2p orbital. Moreover, the manganese 3d states are shown to experience spatial delocalization involving 0.16 electrons per Mn site during the battery operation. Our analysis provides a clear understanding of the funda…
Existence of van der Waals gaps renders two-dimensional (2D) materials ideal passages of lithium for being used as anode materials. However, the requirement of good conductivity significantly limits the choice of 2D candidates. So far only graphite is satisfying due to its relatively high conductivity. Recently, a new polymorph of layered germanium selenide (Gamma-GeSe) was proven to be semimetal in its bulk phase with a higher conductivity than graphite while its monolayer behaves semiconducting. In this work, by using first-principles calculations, we examined the possibility of using this n…
Lithium-ion batteries can last many years but sometimes exhibit rapid, nonlinear degradation that severely limits battery lifetime. In this work, we review prior work on "knees" in lithium-ion battery aging trajectories. We first review definitions for knees and three classes of "internal state trajectories" (termed snowball, hidden, and threshold trajectories) that can cause a knee. We then discuss six knee "pathways", including lithium plating, electrode saturation, resistance growth, electrolyte and additive depletion, percolation-limited connectivity, and mechanical deformation -- some of …
Lithium titanium oxide Li$_4$Ti$_5$O$_{12}$ (LTO) is an intriguing anode material promising particularly long lived batteries, due to its remarkable phase stability during (dis)charging of the cell. However, its usage is limited by its low intrinsic electronic conductivity. Introducing oxygen vacancies can be one method to overcome this drawback, possibly by altering the charge carrier transport mechanism. We use Hubbard corrected density-functional theory (DFT+U) to show that polaronic states in combination with a possible hopping mechanism can play a crucial role in the experimentally observ…
Here, we correlate the nanoscale morphology and chemical composition of solid electrolyte interphases (SEI) with the electrochemical property of graphite-based composite electrodes. Using electrochemical strain microscopy (ESM) and X-ray photoelectron spectroscopy (XPS), changes of chemical composition and morphology (Li and F distribution) in SEI layers on the electrodes as a function of solid electrolyte contents are analyzed. As a result, we find a strong correlation between morphological variations on the electrode, Li and F distribution in SEI layer, and Coulomb efficiency. This correlati…
Solid state battery technology has recently garnered considerable interest from companies including Toyota, BMW, Dyson, and others. The primary driver behind the commercialization of solid state batteries (SSBs) is to enable the use of lithium metal as the anode, as opposed to the currently used carbon anode, which would result in ~20% energy density improvement. However, no reported solid state battery to date meets all of the performance metrics of state of the art liquid electrolyte lithium ion batteries (LIBs) and indeed several solid state electrolyte (SSE) technologies may never reach pa…
This report presents some of the key laboratory electrochemical battery testing methods that are used in fuel cell research. Methods such as voltammetry, chronoamperometry, chronopotentiometry, and electrochemical impedance spectroscopy are of major importance. All the electrochemical corrosion tests are performed through a tri-electrode polarization cell setup containing a reference electrode, a counter electrode, and the working electrode (metal sample of interest) in an electrolyte solution. All three electrodes are connected to a potentiostat. Corrosion of metal occurs through an oxidation…
Cycling efficiency and rate capability of porous copper-coated, amorphous silicon thin-film negative electrodes are compared to equivalent silicon thin-film electrodes in lithium-ion batteries. The presence of a copper layer coated on the active material plays a beneficial role in increasing the cycling efficiency and the rate capability of silicon thin-film electrodes. Between 3C and C/8 discharge rates, the available cell energy decreased by 8% and 18% for 40 nm copper-coated silicon and equivalent silicon thin-film electrodes, respectively. Copper-coated silicon thin-film electrodes also sh…
The surface coating of cathodes using insulator films has proven to be a promising method for high-voltage cathode stabilization in Li-ion batteries. However, there is still substantial uncertainty about how these films function, specifically with regard to important coating design principles such as lithium solubility and transport through the films. This study uses Density Functional Theory to examine the diffusivity of interstitial lithium in crystalline α-$AlF_3$, α-$Al_2O_3$, m-$ZrO_2$, c-MgO, and α-quartz $SiO_2$, which provide benchmark cases for further understanding of insulator coati…
The market quest for fast-charging, safe, long-lasting and performant batteries drives the exploration of new energy storage materials, but also promotes fundamental investigations of materials already widely used. Presently, revamped interest in anode materials is observed -- primarily graphite electrodes for lithium-ion batteries. Here, we focus on the upper limit of lithium intercalation in the morphologically quasi-ideal highly oriented pyrolytic graphite (HOPG), with a LiC$_6$ stoichiometry corresponding to 100\% state of charge (SOC). We prepared a sample by immersion in liquid lithium a…
Key to advancing lithium-ion battery technology, and in particular fast charging capabilities, is our ability to follow and understand the dynamic processes occurring in operating materials under realistic conditions, in real time, and on the nano- to meso-scale. Currently, operando imaging of lithium-ion dynamics requires sophisticated synchrotron X-ray or electron microscopy techniques, which do not lend themselves to high-throughput material screening. This limits rapid and rational materials improvements. Here we introduce a simple lab-based, optical interferometric scattering microscope t…
In this work, the mechanism of Li insertion in $η'$-Cu$_6$Sn$_5$ to form Li$_2$CuSn is discussed in detail, based on both theoretical calculations and experimental results. The mechanism is investigated by means of first principles calculations, with the full potential linearized augmented plane wave method, in combination with {\it in situ} X-ray diffraction experiments. The $η'$-Cu$_6$Sn$_5$ structure, as well as its lithiated products, have been optimized and the electronic charge density calculated in order to study the change in bond character on lithiation. The average insertion voltage …
Composite cathode coatings made of a high energy density layered oxide (Li1.2Ni0.15Mn0.55Co0.1O2, theoretical capacity ~377 mAh/g), polyvinylidene fluoride (PVdF) binder, and electron-conduction additives, were bonded to an elastic substrate. An electrochemical cell, built by pairing the cathode with a capacity-matched graphite anode, was electrochemically cycled and the real-time average stress evolution in the cathode coating was measured using a substrate-curvature technique. Features in the stress evolution profile showed correlations with phase changes in the oxide, thus yielding data com…
The prospects of phosphorene as an anode material for high performance Li-ion battery was systematically investigated from the first principle calculations and experimental measurements. The diffusion energy barriers of a Li atom moving along various orientations on phosphorene layer were calculated from the Li adsorption energy landscape. It was found that the diffusion mobility of a Li atom along the zigzag direction in the valley of phosphorene could be about 7 to 11 orders of magnitude faster than that along the other directions, indicating its ultrafast and anisotropic diffusivity. The li…
A thick electrode with high areal capacity has been developed as a strategy for high-energy-density lithium-ion batteries, but thick electrodes have difficulties in manufacturing and limitations in ion transport. Here, we reported a new manufacturing approach for ultra-thick electrode with aligned structure, called structure electrode additive manufacturing or SEAM, which aligns active materials to the through-thicknesses direction of electrodes using shear flow and a designed printing path. The ultra-thick electrodes with high loading of active materials, low tortuous structure, and good stru…
Electrodeposition and stripping are fundamental electrochemical processes for metals and have gained importance in rechargeable Li-ion batteries due to lithium metal electrodes. The electrode kinetics associated with lithium metal electrodeposition and stripping is crucial in determining performance at fast discharge and charge which is important for electric vertical take-off and landing (eVTOL) aircraft and electric vehicles (EV). In this work, we show the use of Marcus-Hush-Chidsey (MHC) kinetics to accurately predict the Tafel curve data from the work of Boyle et al. We discuss the differe…
A safe lithium-sulfur (Li-S) battery employs a composite polymer electrolyte based on a poly(ethylene glycol) dimethyl ether (PEGDME) solid at room temperature. The electrolyte membrane enables a stable and reversible Li-S electrochemical process already at 50°C, with low resistance at the electrode/electrolyte interphase and fast Li+ transport. The relatively low molecular weight of the PEGDME and the optimal membrane composition in terms of salts and ceramic allow a liquid-like Li-S conversion reaction by heating at moderately high temperature, still holding the solid-like polymer state of t…
The decomposition of ethylene carbonate (EC) during the initial growth of solid-electrolyte interphase (SEI) films at the solvent-graphitic anode interface is critical to lithium ion battery operations. Ab initio molecular dynamics simulations of explicit liquid EC/graphite interfaces are conducted to study these electrochemical reactions. We show that carbon edge terminations are crucial at this stage, and that achievable experimental conditions can lead to surprisingly fast EC breakdown mechanisms, yielding decomposition products seen in experiments but not previously predicted.
Electrochemical impedance spectra for battery electrodes are usually interpreted using models that assume isotropic active particles, having uniform current density and symmetric diffusivities. While this can be reasonable for amorphous or polycrystalline materials with randomly oriented grains, modern electrode materials increasingly consist of highly anisotropic, single-crystalline, nanoparticles, with different impedance characteristics. In this paper, analytical expressions are derived for the impedance of anisotropic particles with tensorial diffusivities and orientation-dependent surface…
Here we report fabrication of flexible and stretchable battery composed of strain free LiFePO4 cathode, Li4Ti5O10 anode and a solid poly ethylene oxide (PEO) electrolyte as a separator layer. The battery is developed in a view of smart textile applications. Featuring solid thermoplastic electrolyte as a key enabling element this battery is potentially extrudable or drawable into fibers or thin stripes which are directly compatible with the weaving process used in smart textile fabrication. The paper first details the choice of materials, fabrication and characterisation of electrodes and a sep…
As a new type of self-healing material, room-temperature liquid metal (LM) composed of Ga, In and Sn is a promising anode in lithium-ion batteries (LIBs). It is difficult to directly prepare an electrode slurry with pure LM. Here, the LM electrode slurry was successfully prepared by simple high-speed stirring method. The LM in the slurry was evenly distributed in the form of liquid particles (average size 100 μm) and no aggregation occurred. The initial discharge specific capacity of LM is 1148 mAh g-1, and the stable discharge specific capacity is 350 mAh g-1. Cyclic voltammetry measurements …
Fracture of lithium-ion battery electrodes is found to contribute to capacity fade and reduce the lifespan of a battery. Traditional fracture models for batteries are restricted to consideration of a single, idealised particle; here, advanced X-ray computed tomography (CT) imaging, an electro-chemo-mechanical model and a phase field fracture framework are combined to predict the void-driven fracture in the electrode particles of a realistic battery electrode microstructure. The electrode is shown to exhibit a highly heterogeneous electrochemical and fracture response that depends on the partic…
Lithium (Li) metal anodes are essential for developing next-generation high-energy-density batteries. Numerous concerns on the potential safety hazards of the Li metal have been brought up before its massive application in commercialized battery packs. However, few investigations have been performed to systematically evaluate the reactivity of Li metal anode in full cell level. Here, differential scanning calorimetry (DSC) with in situ Fourier-transform infrared spectroscopy (FTIR) are used to quantitatively investigate the Li metal reactivity. Lithiated graphite (Li-Gr) and lithiated silicon …
A major challenge in the development of new battery materials is understanding their fundamental mechanisms of operation and degradation. Their microscopically inhomogeneous nature calls for characterization tools that provide operando and localized information from individual grains and particles. Here we describe an approach that images the nanoscale distribution of ions during electrochemical charging of a battery in a transmission electron microscope liquid flow cell. We use valence energy-loss spectroscopy to track both solvated and intercalated ions, with electronic structure fingerprint…
The structure of lithium ion battery components, such as electrodes and separators, are commonly characterised in terms of their porosity and tortuosity. The ratio of these values gives the effective transport of lithium ions in the electrolyte-filled pore spaces, which can be used to determine the ionic resistivity and corresponding voltage losses. Here, we show that these microstructural characteristics are not sufficient. Analysis of tomographic data of commercial separators reveals that different polyolefin separators have similar porosity and through-plane tortuosity, which, in the homoge…
The short diffusion lengths in insertion battery nanoparticles render the capacitive behavior of bounded diffusion, which is rarely observable with conventional larger particles, now accessible to impedance measurements. Coupled with improved geometrical characterization, this presents an opportunity to measure solid diffusion more accurately than the traditional approach of fitting Warburg circuit elements, by properly taking into account the particle geometry and size distribution. We revisit bounded diffusion impedance models and incorporate them into an overall impedance model for differen…
Dendrite growth is a long-standing challenge that has limited the applications of rechargeable lithium metal electrodes. Here, we developed a grand potential based nonlinear phase-field model to study the electrodeposition of lithium as relevant for a lithium metal anode, using open-source software package MOOSE. The dynamic morphological evolution under large/small overpotential is studied in 2-dimensions, revealing important dendrite growth/stable deposition patterns. The corresponding temporal-spatial distributions of ion concentration, overpotential and driving force are studied, which dem…
Identifying overpotential components of electrochemical systems enables quantitative analysis of polarization contributions of kinetic processes under practical operating conditions. However, the inherently coupled kinetic processes lead to an enormous challenge in measuring individual overpotentials, particularly in composite electrodes of lithium-ion batteries. Herein, the full decomposition of electrode overpotential is realized by the collaboration of single-layer structured particle electrode (SLPE) constructions and time-resolved potential measurements, explicitly revealing the evolution…
Adding porosity to battery electrodes is believed to be universally useful for adding space to accommodate volumetric expansion, electrolyte access to all active materials, helping to mitigate poor C-rate performance for thicker electrodes and for allowing infilling with other materials. Ordered porous electrode, such as inverse opals that have macroporosity, have been a model system: binder and conductive additive free, interconnected electrically, defined porosity and pore size with thickness, good electrolyte wettability and surprisingly good electrode performance in half cells and Li-batte…
Silicon is viewed as an excellent electrode material for lithium batteries due to its high lithium storage capacity. Various Si nano-structures, such as Si nanowires, have performed well as lithium battery anodes and have opened up exciting opportunities for the use of Si in energy storage devices. The mechanism of lithium insertion and the interaction between Li and the Si electrode must be understood at the atomic level; this understanding can be achieved by first-principles simulation. Here, first-principles computations of lithiation in silicon electrodes are reviewed. The review focuses o…
Battery electrode surfaces are generally coated with electronically insulating solid films of thickness 1-50 nm. Both electrons and Li+ can move at the electrode-surface film interface in response to the voltage, which adds complexity to the "electric double layer" (EDL). We apply Density Functional Theory (DFT) to investigate how the applied voltage is manifested as changes in the EDL at atomic lengthscales, including charge separation and interfacial dipole moments. Illustrating examples include Li(3)PO(4), Li(2)CO(3), and Li(x)Mn(2)O(4) thin-films on Au(111) surfaces under ultrahigh vacuum …
The improvement of Li-ion battery performance requires development of models that capture the essential physics and chemistry in Li-ion battery electrode materials. In this paper a novel electrochemical phase-field model is presented that captures the thermodynamic and kinetic properties of lithium-insertion in TiO$_2$-anatase, a well-known and intensively studied Li-ion battery electrode material. Previous experimental work on lithiated anatase TiO$_2$ provided all parameters necessary for the phase-field simulations, giving the opportunity to gain fundamental insight in the lithiation of ana…
A LiFe0.6Mn0.4PO4 (LFMP) cathode exploiting the olivine structure is herein synthesized and characterized in terms of structure, morphology, and electrochemical features in a lithium cell. The material shows reversibility of the electrochemical process which evolves at 3.5 and 4 V versus Li+/Li due to the Fe+2/Fe+3 and Mn+2/Mn+3 redox couples, respectively, as determined by cyclic voltammetry. The LFMP has a well-defined olivine structure revealed by X-ray diffraction, a morphology consisting of submicron particle aggregated into micrometric clusters as indicated by scanning and transmission e…
