We report the fabrication of hexagonal-boron-nitride (hBN) encapsulated multi-terminal WSe$_2$ Hall bars with 2D/2D low-temperature Ohmic contacts as a platform for investigating the two-dimensional (2D) metal-insulator transition. We demonstrate that the WSe$_2$ devices exhibit Ohmic behavior down to 0.25 K and at low enough excitation voltages to avoid current-heating effects. Additionally, the high-quality hBN-encapsulated WSe$_2$ devices in ideal Hall-bar geometry enable us to accurately determine the carrier density. Measurements of the temperature ($T$) and density ($n_s$) dependence of the conductivity $σ(T,n_s)$ demonstrate scaling behavior consistent with a metal-insulator quantum phase transition driven by electron-electron interactions, but where disorder-induced local magnetic moments are also present. Our findings pave the way for further studies of the fundamental quantum mechanical properties of 2D transition metal dichalcogenides using the same contact engineering.
We report a new strategy for fabricating 2D/2D low-resistance ohmic contacts for a variety of transition metal dichalcogenides (TMDs) using van der Waals assembly of substitutionally doped TMDs as drain/source contacts and TMDs with no intentional doping as channel materials. We demonstrate that few-layer WSe2 field-effect transistors (FETs) with 2D/2D contacts exhibit low contact resistances of ~ 0.3 k ohm.um, high on/off ratios up to > 109, and high drive currents exceeding 320 uA um-1. These favorable characteristics are combined with a two-terminal field-effect hole mobility ~ 2x102 cm2 V-…
We report the first observation of gate-controlled field emission current from a tungsten diselenide (WSe2) monolayer, synthesized by chemical-vapour deposition on SiO2/Si substrate. Ni contacted WSe2 monolayer back-gated transistors, under high vacuum, exhibit n-type conduction and drain-bias dependent transfer characteristics, which are attributed to oxygen/water desorption and drain induced Schottky barrier lowering, respectively. The gate-tuned n-type conduction enables field emission, i.e. the extraction of electrons by quantum tunnelling, even from the flat part of the WSe2 monolayers. E…
We demonstrate dual-gated $p$-type field-effect transistors (FETs) based on few-layer tungsten diselenide (WSe$_2$) using high work-function platinum source/drain contacts, and a hexagonal boron nitride top-gate dielectric. A device topology with contacts underneath the WSe$_2$ results in $p$-FETs with $I_{ON}$/$I_{OFF}$ ratios exceeding 10$^7$, and contacts that remain Ohmic down to cryogenic temperatures. The output characteristics show current saturation and gate tunable negative differential resistance. The devices show intrinsic hole mobilities around 140 cm$^2$/Vs at room temperature, an…
We report the fabrication of both n-type and p-type WSe2 field effect transistors with hexagonal boron nitride passivated channels and ionic-liquid (IL)-gated graphene contacts. Our transport measurements reveal intrinsic channel properties including a metal-insulator transition at a characteristic conductivity close to the quantum conductance e2/h, a high ON/OFF ratio of >107 at 170 K, and large electron and hole mobility of ~200 cm2V-1s-1 at 160 K. Decreasing the temperature to 77 K increases mobility of electrons to ~330 cm2V-1s-1 and that of holes to ~270 cm2V-1s-1. We attribute our abilit…
Valley degree of freedom in the 2D semiconductor is a promising platform for the next generation optoelectronics. Electrons in different valleys can have opposite Berry curvature, leading to the valley Hall effect (VHE). However, VHE without the plasmonic structure's assistance has only been reported in cryogenic temperature, limiting its practical application. Here, we report the observation of VHE at room temperature in the MoS2/WSe2 heterostructures. We also uncover that both the magnitude and the polarity of the VHE in the 2D heterostructure is gate tunable. We attribute this to the opposi…
For carbon nanotube transistors, as for graphene, the electrical contacts are a key factor limiting device performance. We calculate the device characteristics as a function of nanotube diameter and metal workfunction. Although the on-state current varies continuously, the transfer characteristics reveal a relatively abrupt crossover from Schottky to ohmic contacts. We find that typical high-performance devices fall surprisingly close to the crossover. Surprisingly, tunneling plays an important role even in this regime, so that current fails to saturate with gate voltage as was expected due to…
We report on ultra-wide bandgap (UWBG) Al0.75Ga0.25N channel metal-insulator-semiconductor field-effect transistors (MISFET) with heterostructure engineered low-resistance ohmic contacts. The low intrinsic electron affinity of AlN (0.6 eV) leads to large Schottky barriers at metal-AlGaN interface, resulting in highly resistive ohmic contacts. In this work, we use reverse compositional graded n++ AlGaN contact layer to achieve upward electron affinity grading, leading to a low specific contact resistance of 1.9x10-6 ohm.cm2 to n-Al0.75Ga0.25N channels (bandgap ~ 5.3 eV) with non-alloyed contact…
Proximity orbital and spin-orbit effects of bilayer graphene on monolayer WSe$_2$ are investigated from first-principles. We find that the built-in electric field induces an orbital band gap of about 10 meV in bilayer graphene. Remarkably, the proximity spin-orbit splitting for holes is two orders of magnitude---the spin-orbit splitting of the valence band at K is about 2 meV---more than for electrons. Effectively, holes experience spin-valley locking due to the strong proximity of the lower graphene layer to WSe$_2$. However, applying an external transverse electric field of some 1 V/nm, coun…
We study the effect of polymer coating, pressure and temperature on the electrical characteristics of monolayer WSe2 back-gated transistors with quasi-ohmic Ni/Au contacts. We find that the removal of a layer of poly(methyl methacrylate) or decreasing the pressure change the device conductivity from p to n-type. We study the current-voltage characteristics as a function of the temperature and measure a gate-tunable Schottky barrier at the contacts with a height of 60 meV in flat-band condition. We report and discuss a change in the mobility and the subthreshold slope observed with increasing t…
We report a first principles theoretical investigation of quantum transport in monolayer WSe2 field effect transistor (FET). Due to a strong spin-orbit interaction (SOI) and the atomic structure of the two-dimensional (2D) lattice, monolayer WSe2 has an interesting electronic structure that exhibits Zeeman-like up-down spin texture near the K and K' points of the Brillouin zone. In a FET, the gate electric field induces an extra, externally tunable SOI that re-orients the spins into a Rashba-like texture thereby realizing electric control of the spin. Quantum transport is modulated by the spin…
Here, we present a temperature ($T$) dependent comparison between field-effect and Hall mobilities in field-effect transistors based on few-layered WSe$_2$ exfoliated onto SiO$_2$. Without dielectric engineering and beyond a $T$-dependent threshold gate-voltage, we observe maximum hole mobilities approaching 350 cm$^2$/Vs at $T$=300 K. The hole Hall mobility reaches a maximum value of 650 cm$^2$/Vs as $T$ is lowered below $\sim$ 150 K, indicating that insofar WSe$_2$-based field-effect transistors (FETs) display the largest Hall mobilities among the transition metal dichalcogenides. The gate c…
High performance enhancement mode semiconducting carbon nanotube field-effect transistors (CNTFETs) are obtained by combining ohmic metal-tube contacts, high dielectric constant HfO2 films as gate insulators, and electrostatically doped nanotube segments as source/drain electrodes. The combination of these elements affords high ON currents, subthreshold swings of ~ 70-80 mV/decade, and allows for low OFF currents and suppressed ambipolar conduction. The doped source and drain approach resembles that of MOSFETs and can impart excellent OFF states to nanotube FETs under aggressive vertical scali…
Here, we report the photoconducting response of field-effect transistors based on three atomic layers of chemical vapor transport grown WSe$_2$ crystals mechanically exfoliated onto SiO$_2$. We find that tri-layered WSe$_2$ field-effect transistors, built with the simplest possible architecture, can display high hole mobilities ranging from 350 cm$^2$/Vs at room temperature (saturating at a value of ~500 cm$^2$/Vs below 50 K) displaying a strong photocurrent response which leads to exceptionally high photo responsivities up to 7 A/W under white light illumination of the entire channel for powe…
Two key subjects stand out in the pursuit of semiconductor research: material quality and contact technology. The fledging field of atomically thin transition metal dichalcogenides (TMDCs) faces a number of challenges in both efforts. This work attempts to establish a connection between the two by examining the gate-dependent conductance of few-layer (1-5L) WSe2 field effect devices. Measurements and modeling of the subgap regime reveal Schottky barrier transistor behavior. We show that transmission through the contact barrier is dominated by thermionic field emission (TFE) at room temperature…
1 School of Physics and Astronomy, Monash University, Clayton, Victoria 3800, Australia 2 Australian Research Council Centre of Excellence in Future Low-Energy Electronics Technologies (FLEET), Monash University, Clayton, Victoria 3800, Australia 3 Department of Mechanical Engineering, Columbia University, New York, New York 10027, United States 4 Department of Applied Physics and Applied Mathematics, Columbia University, New York, New York 10027, United States 5 School of Physics, the University of Melbourne, Melbourne, VIC 3010, Australia 6 Research Center for Functional Materials, National …
We report high performance p-type field-effect transistors based on single layered (thickness, ~0.7 nm) WSe2 as the active channel with chemically doped source/drain contacts and high-κ gate dielectrics. The top-gated monolayer transistors exhibit a high effective hole mobility of ~250 cm2/Vs, perfect subthreshold swing of ~60 mV/dec, and ION/IOFF of >10^6 at room temperature. Special attention is given to lowering the contact resistance for hole injection by using high work function Pd contacts along with degenerate surface doping of the contacts by patterned NO2 chemisorption on WSe2. The re…
Nonlinear optical frequency conversion, in which optical fields interact with a nonlinear medium to produce new field frequencies, is ubiquitous in modern photonic systems. However, the nonlinear electric susceptibilities that give rise to such phenomena are often challenging to tune in a given material, and so far, dynamical control of optical nonlinearities remains confined to research labs as a spectroscopic tool. Here, we report a mechanism to electrically control second-order optical nonlinearities in monolayer WSe2, an atomically thin semiconductor. We show that the intensity of second-h…
Achieving good quality Ohmic contacts to van der Waals materials is a challenge, since at the interface between metal and van der Waals material, different conditions can occur, ranging from the presence of a large energy barrier between the two materials to the metallization of the layered material below the contacts. In black phosphorus (bP), a further challenge is its high reactivity to oxygen and moisture, since the presence of uncontrolled oxidation can substantially change the behavior of the contacts. In this study, we investigate the influence of the metal used for the contacts to bP a…
Monolayers of molybdenum and tungsten dichalcogenides are direct bandgap semiconductors, which makes them promising for opto-electronic applications. In particular, van der Waals heterostructures consisting of monolayers of MoS2 sandwiched between atomically thin hexagonal boron nitride (hBN) and graphene electrodes allows one to obtain light emitting quantum wells (LEQWs) with low-temperature external quantum efficiency (EQE) of 1%. However, the EQE of MoS2 and MoSe2-based LEQWs shows behavior common for many other materials: it decreases fast from cryogenic conditions to room temperature, un…
Transconductance as a Probe of Valley Thermodynamics in Multilayer WSe$_2$
Research Center for Materials Nanoarchitectonics (MANA), National Institute for Materials Science (NIMS)（物质·材料纳米结构研究センター（MANA），国立物質研究所（NIMS））；Department of Nanotechnology for Sustainable Energy, Kwansei Gakuin University（关西学院大学持続可能エネルギーナノテクノロジー学科）
Heavy metal-based two-dimensional van der Waals materials have a large, coupled spin and valley Hall effect (SVHE) that has potential use in spintronics and valleytronics. Optical measurements of the SVHE have largely been performed below 30 K and understanding of the SVHE-induced spin/valley polarizations that can be electrically generated is limited. Here, we study the SVHE in monolayer p-type tungsten diselenide (WSe2). Kerr rotation (KR) measurements show the spatial distribution of the SVHE at different temperatures, its persistence up to 160 K, and that it can be electrically modulated v…
To explore the potential of field-effect transistors (FETs) based on monolayers of the two-dimensional semiconducting channel(SC) for spintronics, the two most important issues are to ensure the formation of variable low resistive tunnel ferromagnetic contacts(FC), and to preserve intrinsic properties of the SC during fabrication. Large Schottky barriers lead to the formation of high resistive contacts and methods adopted to control the barriers often alter the intrinsic properties of the SC. This work aims at addressing both issues in fully encapsulated monolayer WSe$_2$ FETs by using bi-laye…
Valley-Landscape Engineering in Bilayer WSe$_2$ Gate-All-Around Transistors
Research Center for Materials Nanoarchitectonics (MANA), National Institute for Materials Science (NIMS)（物质·材料纳米构筑研究中心，日本国立材料研究所）；Kwansei Gakuin University（关西学院大学）
The electrical contact to two-dimensional (2D)-semiconductor materials are decisive to the electronic performance of 2D-semiconductor field-effect devices (FEDs). The presence of a Schottky barrier often leads to a large contact resistance, which seriously limits the channel conductance and carrier mobility measured in a two-terminal geometry. In contrast, ohmic contact is desirable and can be achieved by the presence of a nonrectifying or tunneling barrier. Here, we demonstrate that an nonrectifying barrier can be realized by contacting indium (In), a low work function metal, with layered InS…
A nanoscale device consisting of a metal nanowire, a dielectric, and a gate is proposed. A combination of quantum and thermal stochastic effects enable the device to have multiple functionalities, serving alternately as a transistor, a variable resistor, or a simple resistive element with $I-V$ characteristics that can switch between ohmic and non-ohmic. By manipulating the gate voltage, stochastic transitions between different conducting states of the nanowire can be induced, with a switching time as short as picoseconds. With an appropriate choice of dielectric, the transconductance of the d…
Two-dimensional material-based field effect transistors (2DM-FETs) are playing a revolutionary role in electronic devices. However, after years of development, no device model can match the Pao-Sah model for standard silicon-based transistors in terms of physical accuracy and computational efficiency to support large-scale integrated circuit design. One remaining critical obstacle is the contacts of 2DM-FETs. In order to self-consistently include the contact effect in the current model, it is necessary to perform self-consistent calculations, which is a fatal flaw for applications that priorit…
We have addressed the microscopic transport mechanism at the switching or on-off transition in transition metal dichalcogenide (TMDC) field-effect transistors (FET), which has been a controversial topic in TMDC electronics, especially at room temperature. With simultaneous measurement of channel conductivity and its slow time-dependent fluctuation (or noise) in ultra-thin WSe2 and MoS2 FETs on insulating SiO2 substrates, where noise arises from McWhorter-type carrier number fluctuations, we establish that the switching in conventional backgated TMDC FETs is a classical percolation transition i…
We present, here, advanced DFT-NEGF techniques that we have implemented in our ATOmistic MOdelling Solver, ATOMOS, to explore transport in novel materials and devices and in particular in van-der-Waals heterojunction transistors. We describe our methodologies using plane-wave DFT, followed by a Wannierization step, and linear combination of atomic orbital DFT, that leads to an orthogonal and non-orthogonal NEGF model, respectively. We then describe in detail our non-orthogonal NEGF implementation including the Sancho-Rubio and electron-phonon scattering within a non-orthogonal framework. We al…
Single-layer transition metal dichalcogenide (TMD) WSe2 has recently attracted a lot of attention because it is a 2D semiconductor with a direct band-gap. Due to low doping levels it is intrinsic and shows ambipolar transport. This opens up the possibility to realize devices with the Fermi level located in valence band, where the spin/valley coupling is strong and leads to new and interesting physics. As a consequence of its intrinsically low doping, large Schottky barriers form between WSe2 and metal contacts, which impede the injection of charges at low temperatures. Here, we report on the s…
We fabricate high-mobility p-type few-layer WSe2 field-effect transistors and surprisingly observe a series of quantum Hall (QH) states following an unconventional sequence predominated by odd-integer states under a moderate strength magnetic field. By tilting the magnetic field, we discover Landau level (LL) crossing effects at ultra-low coincident angles, revealing that the Zeeman energy is about three times as large as the cyclotron energy near the valence band top at Γ valley. This result implies the significant roles played by the exchange interactions in p-type few-layer WSe2, in which i…
We have studied metal/organic semiconductor charge injection in poly(3-hexylthiophene) (P3HT) field-effect transistors with Pt and Au electrodes as a function of annealing in vacuum. At low impurity dopant densities, Au/P3HT contact resistances increase and become nonohmic. In contrast, Pt/P3HT contacts remain ohmic even at far lower doping. Ultraviolet photoemission spectroscopy (UPS) reveals that metal/P3HT band alignment shifts dramatically as samples are dedoped, leading to an increased injection barrier for holes, with a greater shift for Au/P3HT. These results demonstrate that doping can…
Current voltage and Kelvin Probe Force Microscopy (KPFM) measurements were performed on single ZnO nanowires. Measurements are shown to be strongly correlated with the contact behavior, either ohmic or Schottky. The ZnO nanowires were obtained by metallo-organic chemical vapor deposition (MOCVD) and contacted using electronic-beam lithography. Depending on the contact geometry, good quality ohmic contacts (linear I V behavior) or non-linear (diode like) Schottky contacts were obtained. Current voltage and KPFM measurements on both types of contacted ZnO nanowires were performed in order to inv…
Low carrier mobility and high electrical contact resistance are two major obstacles prohibiting explorations of quantum transport in TMDCs. Here, we demonstrate an effective method to establish low-temperature Ohmic contacts in boron nitride encapsulated TMDC devices based on selective etching and conventional electron-beam evaporation of metal electrodes. This method works for most extensively studied TMDCs in recent years, including MoS2, MoSe2, WSe2, WS2, and 2H-MoTe2. Low electrical contact resistance is achieved at 2 K. All of the few-layer TMDC devices studied show excellent performance …
We explore solid electrolytes for electrostatic gating using field-effect transistors (FETs) in which thin WSe$_2$ crystals are exfoliated and transferred onto a lithium-ion conducting glass ceramic substrate. For negative gate voltages ($V_G < 0$) the devices work equally well as ionic liquid gated FETs while offering specific advantages, whereas no transistor action is seen for $V_G>0$. For $V_G <0$ the devices can nevertheless be driven into the ambipolar injection regime by applying a large source-drain bias, and strong electroluminescence is observed when direct band-gap WSe$_2$ monolayer…
We use numerical simulations to investigate the effect of electrostatics on the source and drain contacts of carbon nanotube field-effect transistors. We find that unscreened charge on the nanotube at the contact-channel interface leads to a potential barrier that can significantly hamper transport through the device. This effect is largest for intermediate gate voltages and for contacts near the ohmic-Schottky crossover, but can be mitigated with a reduction in the gate oxide thickness. These results help to elucidate the important role that contact geometry plays in the performance of carbon…
This work evaluates the performance of carbon nanotube field effect transistors (CNTFET) using few layer graphene as the contact electrode material. We present the experimental results obtained on the barrier height at CNT graphene junction using temperature dependent IV measurements. The estimated barrier height in our devices for both holes and electrons is close to zero or slightly negative indicating the Ohmic contact of graphene with the valence and conduction bands of CNTs. In addition, we also report that there is no correlation between the barrier height and thickness of graphene.
Selenization of V$_2$O$_5$/WO$_3$ Bilayers for Tuned Optoelectronic Response of WSe$_2$ Films
Morgan State University（摩根州立大学）；DOD Center of Excellence for Advanced Electro-Photonics with 2D Materials, Morgan State University（二维材料先进电光子学国防部卓越中心，摩根州立大学）；DEVCOM Army Research Laboratory（美国陆军研究实验室）
Modulation-doped AlGaAs/GaAs heterostructures are utilized extensively in the study of quantum transport in nanostructures, but charge fluctuations associated with remote ionized dopants often produce deleterious effects. Electric field-induced carrier systems offer an attractive alternative if certain challenges can be overcome. We demonstrate a field-effect transistor in which the active channel is locally devoid of modulation-doping, but silicon dopant atoms are retained in the ohmic contact region to facilitate reliable low-resistance contacts. A high quality two-dimensional electron gas i…
The observed performances of carbon nanotube field effect transistors are examined using first-principles quantum transport calculations. We focus on the nature and role of the electrical contact of Au and Pd electrodes to open-ended semiconducting nanotubes, allowing the chemical contact at the surface to fully develop through large-scale relaxation of the contacting atomic configuration. We present the first direct numerical evidence of Pd contacts exhibiting perfect transparency for hole injection as opposed to that of Au contacts. Their respective Schottky barrier heights, on the other han…
In this article, a novel two-path model is proposed to quantitatively explain sub-threshold characteristics of back-gated Schottky barrier FETs (SB-FETs) from 2D channel materials. The model integrates the 'conventional' model for SB-FETs with the phenomenon of contact gating - an effect that significantly affects the carrier injection from the source electrode in back-gated field effect transistors. The two-path model is validated by a careful comparison with experimental characteristics obtained from a large number of back-gated WSe2 devices with various channel thicknesses. Our findings are…
Pumping characteristics were studied of the hybrid normal-metal/superconductor single-electron transistor embedded in a high-ohmic environment. Two 3 micrometer-long microstrip resistors of CrOx with a sum resistance R=80kOhm were placed adjacent to this hybrid device. Substantial improvement of pumping and reduction of the subgap leakage were observed in the low-MHz range. At higher frequencies 0.1-1GHz, a slowdown of tunneling due to the enhanced damping and electron heating negatively affected the pumping, as compared to the reference bare devices.
We study field effect transistor characteristics in etched single layer MoS2 nanoribbon devices of width 50nm with ohmic contacts. We employ a SF6 dry plasma process to etch MoS2 nanoribbons using low etching (RF) power allowing very good control over etching rate. Transconductance measurements reveal a steep sub-threshold slope of 3.5V/dec using a global backgate. Moreover, we measure a high current density of 38 uA/um resulting in high on/off ratio of the order of 10^5. We observe mobility reaching as high as 50 cm^2/V.s with increasing source-drain bias.
We present temperature dependent $I-V$ measurements of short channel MoS$_2$ field effect devices at high source-drain bias. We find that although the $I-V$ characteristics are Ohmic at low bias, the conduction becomes space charge limited at high $V_{DS}$ and existence of an exponential distribution of trap states was observed. The temperature independent critical drain-source voltage ($V_c$) was also determined. The density of trap states was quantitatively calculated from $V_c$. The possible origin of exponential trap distribution in these devices is also discussed.
Emergent inhomogeneity and non-locality in a graphene field-effect transistor on a near-parallel moire superlattice of transition metal dichalcogenides
Controlling the flow of charge neutral interlayer exciton (IX) quasiparticles can potentially lead to low loss excitonic circuits. Here, we report unidirectional transport of IXs along nanoscale electrostatically defined channels in an MoSe$_2$-WSe$_2$ heterostructure. These results are enabled by a lithographically defined triangular etch in a graphene gate to create a potential energy ''slide''. By performing spatially and temporally resolved photoluminescence measurements, we measure smoothly varying IX energy along the structure and high-speed exciton flow with a drift velocity up to 2 * 1…
Ultralow p-type contact resistance for ultra-nanoscaled 2D-materials transistors
Singapore University of Technology and Design（新加坡科技设计大学）；China Jiliang University（中国计量大学）；Hubei Minzu University（湖北民族大学）；National University of Singapore（新加坡国立大学）
We study magneto-electric properties of single electron traps in metal-oxide-semiconductor field effect transistors. Using a microscopic description of the system based on the single-site Anderson-Holstein model, we derive an effective low energy action for the system. The behavior of the system is characterized by simultaneous polaron tunneling (corresponding to the charging and discharging of the trap) and Kondo screening of the trap spin in the singly occupied state. Hence, the obtained state of the system is a hybrid between the Kondo regime, typically associated with single electron occup…
High performance p- and n-type single-walled carbon nanotube (SWNT) field-effect transistors (FETs) are obtained by using high and low work function metals, Pd and Al as source/drain (S/D) electrodes respectively. Ohmic contacts made to chemically intrinsic SWNTs, with no or small Schottky barriers (SB), afford high ON-state currents up to 20 uA per tube. The lack of significant Fermi-level pinning at the nanotube-metal interfaces allows for fine-tuning of the barrier heights for p-and n-channel conductions by changing the contact metals. The air-stable p- and n-FETs thus obtained can be used …
Two-dimensional transitional metal dichalcogenide (TMD) field-effect transistors (FETs) are promising candidates for future electronic applications, owing to their excellent transport properties and potential for ultimate device scaling. However, it is widely acknowledged that substantial contact resistance associated with the contact-TMD interface has impeded device performance to a large extent. It has been discovered that O2 plasma treatment can convert WSe2 into WO3-x and substantially improve contact resistances of p-type WSe2 devices by strong doping induced thinner depletion width. In t…
