Channel estimation in reconfigurable intelligent surface (RIS) assisted multiple input multiple output (MIMO) communication systems is challenging as pilots cannot be decoded at or transmitted from a RIS with only passive elements. We assume an angular model for the line-of-sight channel between the user equipment (UE) and the RIS and between the RIS and the base station (BS) with no direct path between the UE and BS. In this letter, assuming that we can compute the RIS-BS channel (up to a complex path gain) from their known locations, we first discuss the ambiguity involved in estimating the UE-RIS channel. We propose a multiple channel sounding procedure in which we observe the channel through different RIS phase shifts and present an algorithm for channel estimation to resolve this ambiguity. Through simulations, we show that the proposed method is comparable to an oracle estimator, which perfectly knows the BS, UE, and RIS locations.
Full Duplex (FD) communication can revolutionize wireless communications as it avoids using independent channels for bi-directional communications. This work generalizes the point-to-point FD communication in millimeter wave (mmWave) band consisting of K-pairs of massive MIMO FD nodes operating simultaneously. We present a novel joint hybrid beamforming (HYBF) and combining scheme for weighted sum-rate (WSR) maximization to enable the coexistence of massive MIMO FD links cost-efficiently. The proposed algorithm relies on alternative optimization based on the minorization-maximization method. M…
The densely packed antennas of millimeter-Wave (mmWave) MIMO systems are often blocked by the rain, snow, dust and even by fingers, which will change the channel's characteristics and degrades the system's performance. In order to solve this problem, we propose a cross-entropy inspired antenna array diagnosis detection (CE-AAD) technique by exploiting the correlations of adjacent antennas, when blockages occur at the transmitter. Then, we extend the proposed CE-AAD algorithm to the case, where blockages occur at transmitter and receiver simultaneously. Our simulation results show that the prop…
Wireless backhaul is considered to be the key part of the future wireless network with dense small cell traffic and high capacity demand. In this paper, we focus on the design of a high spectral efficiency line-of-sight (LoS) multiple-input multiple-output (MIMO) system for millimeter wave (mmWave) backhaul using dual-polarized frequency division duplex (FDD). High spectral efficiency is very challenging to achieve for the system due to various physical impairments such as phase noise (PHN), timing offset (TO) as well as the poor condition number of the LoS MIMO. In this paper, we propose a ho…
Beam training based on hierarchical codebook for millimeter wave (mmWave) massive MIMO is investigated. Unlike the existing work using the same hierarchical codebook to estimate different multi-path components (MPCs), dynamic hierarchical codebooks which are updated according to the estimated MPCs are adopted. Firstly, a generalized hierarchical codebook design method is proposed. Then based on this method, a beam training method which dynamically updates the hierarchical codebook by removing the contribution of the estimated MPCs from the codebook is proposed. Simulation results verify the ef…
We analyze the diversity gain for a distributed antenna subarray employing orthogonal frequency-division multiplexing (OFDM) in millimeter-wave (mm-Wave) massive multiple-input multiple-output (MIMO) systems. We show that the diversity gain depends on the number of transmitted data streams, the number of remote antenna units, and the number of propagation paths between RAUs. Furthermore, we show that by using bit-interleaved coded multiple beamforming (BICMB), one can achieve the maximum diversity gain in a distributed antenna subarray system. The assumption in both scenarios is that the numbe…
Measurement results for millimeter wave LOS MIMO systems are presented with a focus on time variation and multipath propagation. Different system setups are used, including 2x2 and 3x3 MIMO, and involving different synchronization procedures and front-ends. Furthermore, different propagation scenarios are evaluated, covering a wide area of applications. The results show that the LOS component carries significantly more power than the NLOS components, and that frequency selectivity from front-ends should be taken into account when designing these high bandwidth systems. Frequency offsets and ot…
Massive multiple-input multiple-out (MIMO) technology is vital in millimeter-wave (mmWave) bands to obtain large array gains. However, there are practical challenges, such as high hardware cost and power consumption in such systems. A promising solution to these problems is to adopt a hybrid beamforming architecture. This architecture has a much lower number of transceiver (TRx) chains than the total antenna number, resulting in cost- and energy-efficient systems. In this paper, we present a real-time mmWave (28 GHz) massive MIMO testbed with hybrid beamforming. This testbed has a 64-antenna/1…
Millimeter-wave (mmWave) channels, which occupy frequency ranges much higher than those being used in previous wireless communications systems, are utilized to meet the increased throughput requirements that come with 5G communications. The high levels of attenuation experienced by electromagnetic waves in these frequencies causes MIMO channels to have high spatial correlation. To attain desirable error performances, systems require knowledge about the channel correlations. In this thesis, a deep neural network aided method is proposed for the parametric estimation of the channel covariance ma…
Millimeter-wave (mmWave) multiple-input multiple-output (MIMO) system for the fifth generation (5G) cellular communications can also enable single-anchor positioning and object tracking due to its large bandwidth and inherently high angular resolution. In this paper, we introduce the newly invented concept, large intelligent surface (LIS), to mmWave positioning systems, study the theoretical performance bounds (i.e., Cramér-Rao lower bounds) for positioning, and evaluate the impact of the number of LIS elements and the value of phase shifters on the position estimation accuracy compared to the…
In this paper, a framework of beamspace channel estimation in millimeter wave (mmWave) massive MIMO system is proposed. The framework includes the design of hybrid precoding and combining matrix as well as the search method for the largest entry of over-sampled beamspace receiving matrix. Then based on the framework, three channel estimation schemes including identity matrix approximation (IA)-based scheme, scattered zero off-diagonal (SZO)-based scheme and concentrated zero off-diagonal (CZO)-based scheme are proposed. These schemes together with the existing channel estimation schemes are co…
Intelligent reflecting surfaces (IRSs) are regarded as promising enablers for future millimeter wave (mmWave) wireless communication, due to their ability to create favorable line-of-sight (LoS) propagation environments. In this paper, we investigate channel estimation in downlink IRS-assisted mmWave multiple-input multiple-output (MIMO) systems. By leveraging the sparsity of mmWave channels, we formulate the channel estimation problem as a fixed-rank constrained non-convex optimization problem. To tackle the non-convexity, an efficient algorithm is proposed by capitalizing on alternating mini…
This paper presents LuMaMi28, a real-time 28 GHz massive multiple-input multiple-output (MIMO) testbed. In this testbed, the base station has 16 transceiver chains with a fully-digital beamforming architecture (with different pre-coding algorithms) and simultaneously supports multiple user equipments (UEs) with spatial multiplexing. The UEs are equipped with a beam-switchable antenna array for real-time antenna selection where the one with the highest channel magnitude, out of four pre-defined beams, is selected. For the beam-switchable antenna array, we consider two kinds of UE antennas, with…
Aiming at maximizing the achievable sum-rate of wideband multiuser mmWave massive MIMO systems, the hybrid precoding is studied. Since each computation of the achievable sum-rate can be performed only after the analog precoder and digital precoder are both determined, the maximization of the achievable sum-rate has intractable computational complexity. By introducing the interference free (IF) achievable sum-rate, the design of the analog and digital precoders can be decoupled. To avoid the beam conflict and maximize the IF achievable sum-rate, a Hungarian-based codeword selection algorithm is…
Using out-of-band (OOB) side-information has recently been shown to accelerate beam selection in single-user millimeter wave (mmWave) massive MIMO communications. In this paper, we propose a novel OOB-aided beam selection framework for a mmWave uplink multi-user system. In particular, we exploit spatial information extracted from lower (sub-6 GHz) bands in order to assist with an inter-user coordination scheme at mmWave bands. To enforce coordination, we propose an exchange protocol exploiting device-to-device communications, where low-rate beam-related information is exchanged between the mob…
In this letter, we consider hybrid beamforming for millimeter wave (mmWave) MIMO integrated sensing and communications (ISAC). We design the transmit beam of a dual-functional radar-communication (DFRC) base station (BS), aiming at approaching the objective radar beam pattern, subject to the constraints of the signal to interference-plus-noise ratio (SINR) of communication users and total transmission power of the DFRC BS. To provide additional degree of freedom for the beam design problem, we introduce a phase vector to the objective beam pattern and propose an alternating minimization method…
As communication systems that employ millimeter wave (mmWave) frequency bands must use large antenna arrays to overcome the severe propagation loss of mmWave signals, hybrid beamforming has been considered as an integral component of mmWave communications. Recently, intelligent reflecting surface (IRS) has been proposed as an innovative technology that can significantly improve the performance of mmWave communication systems through the use of low-cost passive reflecting elements. In this paper, we study IRS-aided mmWave multiple-input multiple-output (MIMO) systems with hybrid beamforming arc…
Delay alignment modulation (DAM) is a novel wideband communication technique, which exploits the high spatial resolution and multi-path sparsity of millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems to mitigate inter-symbol interference (ISI), without relying on conventional techniques like channel equalization or multi-carrier transmission. In this paper, we extend the DAM technique to multi-user mmWave massive MIMO communication systems. We first provide asymptotic analysis by showing that when the number of base station (BS) antennas is much larger than the total…
This paper focuses on channel estimation for mmWave MIMO systems with 1-bit spatial sigma-delta analog-to-digital converters (ADCs). The channel estimation performance with 1-bit spatial sigma-delta ADCs depends on the quantization noise modeling. Therefore, we present a new method for modeling the quantization noise by leveraging the deterministic input-output relation of the 1-bit spatial sigma-delta ADC. Using this new noise model, we propose an algorithm for channel estimation for a narrowband single-user mmWave line-of-sight MIMO system by determining the unknown angles and path attenuati…
Use of low resolution analog to digital converters (ADCs) is an effective way to reduce the high power consumption of millimeter wave (mmWave) receivers. In this paper, a receiver with low resolution ADCs based on adaptive thresholds is considered in downlink mmWave communications in which the channel state information is not known a-priori and acquired through channel estimation. A performance comparison of low-complexity algorithms for power and ADC allocation among transmit and receive terminals, respectively, is provided. Through simulation of practical mmWave cellular networks, it is show…
A hybrid architecture for millimeter wave (mmW) massive MIMO systems is considered practically implementable due to low power consumption and high energy efficiency. However, due to the limited number of RF chains, user selection becomes necessary for such architecture. Traditional user selection algorithms suffer from high computational complexity and, therefore, may not be scalable in 5G and beyond wireless mobile communications. To address this issue, in this letter we propose a low complexity CNN framework for user selection. The proposed CNN accepts as input the channel matrix and gives a…
The high energy consumption of massive multi-input multi-out (MIMO) system has become a prominent problem in the millimeter wave(mm-Wave) communication scenario. The hybrid precoding technology greatly reduces the number of radio frequency(RF) chains by handing over part of the coding work to the phase shifting network, which can effectively improve energy efficiency. However, conventional hybrid precoding algorithms based on mathematical means often suffer from performance loss and high computational complexity. In this paper, a novel BP-neural-network-enabled hybrid precoding algorithm is pr…
We address the problem of analyzing and classifying in groups the downlink channel environment in a millimeter-wavelength cell, accounting for path loss, multipath fading, and User Equipment (UE) blocking, by employing a hybrid propagation and multipath fading model, thus using accurate inter-group interference modeling. The base station (BS) employs a large Uniform Planar Array (UPA) to facilitate massive Multiple-Input, Multiple-Output (MIMO) communications with high efficiency. UEs are equipped with a single antenna and are distributed uniformly within the cell. The key problem is analyzing…
Recent applications of the Full Duplex (FD) technology focus on enabling simultaneous control communication and data transmission to reduce the control information exchange overhead, which impacts end-to-end latency and spectral efficiency. In this paper, we present a simultaneous direction estimation and data transmission scheme for millimeter Wave (mmWave) massive Multiple-Input Multiple-Output (MIMO) systems, enabled by a recent FD MIMO technology with reduced hardware complexity Self-Interference (SI) cancellation. We apply the proposed framework in the mmWave analog beam management proble…
Mobility and blockage are two critical challenges in wireless transmission over millimeter-wave (mmWave) and Terahertz (THz) bands. In this paper, we investigate network massive multiple-input multiple-output (MIMO) transmission for mmWave/THz downlink in the presence of mobility and blockage. Considering the mmWave/THz propagation characteristics, we first propose to apply per-beam synchronization for network massive MIMO to mitigate the channel Doppler and delay dispersion effects. Accordingly, we establish a transmission model. We then investigate network massive MIMO downlink transmission …
Millimeter wave (mmWave) band, or high frequencies such as THz, has large undeveloped band of spectrum. However, wireless channels over the mmWave band usually have one or two paths only due to the severe attenuation. The channel property restricts its development in the multiple-input multiple-output (MIMO) system, which can improve throughput by increasing the spectral efficiency. Recent development in reconfigurable intelligent surface (RIS) provides new opportunities to mmWave communications. In this study, we propose a mmWave system, which used low-precision analog-to-digital converters (…
Reconfigurable intelligent surface (RIS) is considered to be an energy-efficient approach to reshape the wireless environment for improved throughput. Its passive feature greatly reduces the energy consumption, which makes RIS a promising technique for enabling the future smart city. Existing beamforming designs for RIS mainly focus on optimizing the spectral efficiency for single carrier systems. To avoid the complicated bit allocation on different spatial domain subchannels in MIMO systems, in this paper, we propose a geometric mean decomposition-based beamforming for RIS-assisted millimeter…
Millimeter wave (mmWave) and terahertz MIMO systems rely on pre-defined beamforming codebooks for both initial access and data transmission. However, most of the existing codebooks adopt pre-defined beams that focus mainly on improving the gain of their target users, without taking interference into account, which could incur critical performance degradation in dense networks. To address this problem, in this paper, we propose a sample-efficient digital twin-assisted beam pattern design framework that learns how to form the beam pattern to reject the signals from the interfering directions. Th…
In this work, the uplink channel estimation problem is considered for a millimeter wave (mmWave) multi-input multi-output (MIMO) system. It is well known that pilot overhead and computation complexity in estimating the channel increases with the number of antennas and the bandwidth. To overcome this, the proposed approach allows the channel estimation at the base station to be aided by the sensing information. The sensing information contains an estimate of scatterers locations in an environment. A simultaneous weighting orthogonal matching pursuit (SWOMP) - sparse Bayesian learning (SBL) algo…
This paper presents an evaluation of distortion and interference sources, namely, the harmonic distortion and antenna crosstalk, originating within a 2 x 2 millimeter-wave (mm-wave) multiple-input-multiple-output (MIMO) testbed. The experience gained through the insight into the built testbed could be fed into the design of future mm-wave massive MIMO testbeds.
Millimeter wave offers high bandwidth for air-to-air (A2A) communication. In this paper, we evaluate the rate performance of a multiuser MIMO (MU-MIMO) configuration where several aircraft communicate with a central hub. We consider a hybrid subarray architecture, single path channels, and realistic atmospheric attenuation effects. We propose a mathematical framework for the analysis of millimeter wave (mmWave) MU-MIMO networks. Via Monte Carlo simulation, we demonstrate that mmWave is a promising technology for delivering gigabit connectivity in next-generation aerial networks.
Machine learning tools are finding interesting applications in millimeter wave (mmWave) and massive MIMO systems. This is mainly thanks to their powerful capabilities in learning unknown models and tackling hard optimization problems. To advance the machine learning research in mmWave/massive MIMO, however, there is a need for a common dataset. This dataset can be used to evaluate the developed algorithms, reproduce the results, set benchmarks, and compare the different solutions. In this work, we introduce the DeepMIMO dataset, which is a generic dataset for mmWave/massive MIMO channels. The …
In this paper, over-the-air experiments with external and internal interferences were performed using Chalmers millimeter-wave multiple-input-multiple-output testbed MATE. The resulting SINR for both interference experiments are compared and discussed.
We investigate beam training and allocation for multiuser millimeter wave massive MIMO systems. An orthogonal pilot based beam training scheme is first developed to reduce the number of training times, where all users can simultaneously perform the beam training with the base station (BS). As the number of users increases, the same beam from the BS may point to different users, leading to beam conflict and multiuser interference. Therefore, a quality-of-service (QoS) constrained (QC) beam allocation scheme is proposed to maximize the equivalent channel gain of the QoS-satisfied users, under th…
Cell-free massive MIMO systems consist of many distributed access points with simple components that jointly serve the users. In millimeter wave bands, only a limited set of predetermined beams can be supported. In a network that consolidates these technologies, downlink analog beam selection stands as a challenging task for the network sum-rate maximization. Low-cost digital filters can improve the network sum-rate further. In this work, we propose low-cost joint designs of analog beam selection and digital filters. The proposed joint designs achieve significantly higher sum-rates than the di…
An intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) massive multiple input multiple output (MIMO) system with transmit antenna selection (TAS) using orthogonal space-time block codes (OSTBC) scheme is proposed in this paper. This system combines TAS and IRS with hybrid analog-digital beamforming (HBF) for 60 GHz mmWave communications in order to exploit the benefits of TAS, OSTBC, analog beamforming (ABF), and transmit digital precoding techniques. The proposed system, however, benefits from the transmit diversity gain of OSTBC scheme as well as from the signal-to-noise r…
In a cell-free massive MIMO architecture a very large number of distributed access points simultaneously and jointly serves a much smaller number of mobile stations; a variant of the cell-free technique is the user-centric approach, wherein each access point just serves a reduced set of mobile stations. This paper introduces and analyzes the cell-free and user-centric architectures at millimeter wave frequencies, considering a training-based channel estimation phase, and the downlink and uplink data transmission phases. First of all, a multiuser clustered millimeter wave channel model is intro…
Millimeter-wave massive multiple-input multiple-output (MIMO) can use a lens antenna array to considerably reduce the number of radio frequency (RF) chains, but channel estimation is challenging due to the number of RF chains is much smaller than that of antennas. By exploiting the sparsity of beamspace channels, the beamspace channel estimation can be formulated as a sparse signal recovery problem, which can be solved by the classical iterative algorithm named approximate message passing (AMP), and its corresponding version learned AMP (LAMP) realized by a deep neural network (DNN). However, …
A fully-digital wideband joint communication-radar (JCR) with a multiple-input-multiple-output (MIMO) architecture at the millimeter-wave (mmWave) band will enable high joint communication and radar performance with enhanced design flexibility. A quantized receiver with few-bit analog-to-digital converters (ADCs) will enable a practical JCR solution with reduced power consumption for futuristic portable devices and autonomous vehicles. In this paper, we present a joint communication-radar proof-of-concept platform, named JCR70, to evaluate and demonstrate the performance of these JCR systems u…
While mmWave bands provide a large bandwidth for mobile broadband services, they suffer from severe path loss and shadowing. Multiple-antenna techniques such as beamforming (BF) can be applied to compensate the signal attenuation. We consider a special case of hybrid BF called per-stream hybrid BF (PSHBF) which is easier to implement than the general hybrid BF because it circumvents the need for joint analog-digital beamformer optimization. Employing BF at the base station enables the transmission of multiple data streams to several users in the same resource block. In this paper, we provide a…
Duzce University（杜兹切大学）；University of Hertfordshire（赫特福德大学）；University of Luxembourg（卢森堡大学）
In multi-user millimeter wave (mmWave) multiple-input-multiple-output (MIMO) systems, hybrid precoding is a crucial task to lower the complexity and cost while achieving a sufficient sum-rate. Previous works on hybrid precoding were usually based on optimization or greedy approaches. These methods either provide higher complexity or have sub-optimum performance. Moreover, the performance of these methods mostly relies on the quality of the channel data. In this work, we propose a deep learning (DL) framework to improve the performance and provide less computation time as compared to convention…
In this paper, we present a novel real-time multiple-input-multiple-output (MIMO) channel sounder for the 28 GHz band. Until now, most investigations of the directional characteristics of millimeter-wave channels have used mechanically rotating horn antennas. In contrast, the sounder presented here is capable of performing horizontal and vertical beam steering with the help of phased arrays. Due to its fast beam-switching capability, the proposed sounder can perform measurements that are directionally resolved both at the transmitter(TX) and receiver (RX) in 1.44 milliseconds compared to the m…
Using millimeter-wave (mmWave) bands is expected to provide high data rates through large licensed and unlicensed spectrum. Due to large path loss and sparse scattering propagation properties, proper beam alignment is important in mmWave systems. Small carrier wavelengths at mmWave bands let wireless communication systems use large antenna arrays to provide sufficient beamforming gain with highly directional beams. Hence, high resolution channel angle-of-departure (AoD) and angle-of-arrival (AoA) estimation is crucial for beam alignment to get the advantages of large beamforming gain. Using la…
The UFMC modulation is among the most considered solutions for the realization of beyond-OFDM air interfaces for future wireless networks. This paper focuses on the design and analysis of an UFMC transceiver equipped with multiple antennas and operating at millimeter wave carrier frequencies. The paper provides the full mathematical model of a MIMO-UFMC transceiver, taking into account the presence of hybrid analog/digital beamformers at both ends of the communication links. Then, several detection structures are proposed, both for the case of single-packet isolated transmission, and for the c…
Millimeter-wave (mmWave) multiple-input multiple-out (MIMO) systems relying on lens antenna arrays are capable of achieving a high antenna-gain at a considerably reduced number of radio frequency (RF) chains via beam selection. However, the traditional beam selection network suffers from significant performance loss in wideband systems due to the effect of beam squint. In this paper, we propose a phase shifter-aided beam selection network, which enables a single RF chain to support multiple focused-energy beams, for mitigating the beam squint in wideband mmWave MIMO systems. Based on this arch…
Millimeter-wave (MMW) imaging has a wide prospect in application of concealed weapons detection. We propose a circular-arc multiple-input multiple-output (MIMO) array scheme with uniformly spaced transmit and receive antennas along the horizontal-arc direction, while scanning along the vertical direction. The antenna beams of the circular-arc MIMO array can provide more uniform coverage of the imaging scene than those of the linear or planar MIMO arrays. Further, a near-field three-dimensional (3-D) imaging algorithm, based on the spatial frequency domain processing, is presented with analysis…
Channel estimation (CE) for millimeter-wave (mmWave) lens-array suffers from prohibitive training overhead, whereas the state-of-the-art solutions require an extra complicated radio frequency phase shift network. By contrast, lens-array using antenna switching network (ASN) simplifies the hardware, but the associated CE is a challenging task due to the constraint imposed by ASN. This paper proposes a compressive sensing (CS)-based CE solution for full-dimensional (FD) lens-array, where the mmWave channel sparsity is exploited. Specifically, we first propose an approach of pilot training under …
Millimeter wave multiple-input multiple-output (MIMO) communication systems must operate over sparse wireless links and will require large antenna arrays to provide high throughput. To achieve sufficient array gains, these systems must learn and adapt to the channel state conditions. However, conventional MIMO channel estimation can not be directly extended to millimeter wave due to the constraints on cost-effective millimeter wave operation imposed on the number of available RF chains. Sparse subspace scanning techniques that search for the best subspace sample from the sounded subspace sampl…
Due to their ability to create favorable line-of-sight (LoS) propagation environments, intelligent reflecting surfaces (IRSs) are regarded as promising enablers for future millimeter-wave (mm-wave) wireless communication. In this paper, we investigate channel estimation for IRS-assisted mm-wave multiple-input multiple-output (MIMO) {\color{black}wireles}s systems. By leveraging the sparsity of mm-wave channels in the angular domain, we formulate the channel estimation problem as an $\ell_1$-norm regularized optimization problem with fixed-rank constraints. To tackle the non-convexity of the fo…
Employing large antenna arrays is a key characteristic of millimeter wave (mmWave) and terahertz communication systems. Due to the hardware constraints and the lack of channel knowledge, codebook based beamforming/combining is normally adopted to achieve the desired array gain. However, most of the existing codebooks focus only on improving the gain of their target user, without taking interference into account. This can incur critical performance degradation in dense networks. In this paper, we propose a sample-efficient online reinforcement learning based beam pattern design algorithm that l…
Hybrid analog-digital precoding is challenging for broadband millimeter-wave (mmWave) massive MIMO systems, since the analog precoder is frequency-flat but the mmWave channels are frequency-selective. In this paper, we propose a principal component analysis (PCA)-based broadband hybrid precoder/combiner design, where both the fully-connected array and partially-connected subarray (including the fixed and adaptive subarrays) are investigated. Specifically, we first design the hybrid precoder/combiner for fully-connected array and fixed subarray based on PCA, whereby a low-dimensional frequency-…
Employing large antenna arrays is a key characteristic of millimeter wave (mmWave) and terahertz communication systems. However, due to the adoption of fully analog or hybrid analog/digital architectures, as well as non-ideal hardware or arbitrary/unknown array geometries, the accurate channel state information becomes hard to acquire. This impedes the design of beamforming/combining vectors that are crucial to fully exploit the potential of large-scale antenna arrays in providing sufficient receive signal power. In this paper, we develop a novel framework that leverages deep reinforcement lea…
Herein, an atomic norm based method for accurately estimating the location and orientation of a target from millimeter-wave multi-input-multi-output (MIMO) orthogonal frequency-division multiplexing (OFDM) signals is presented. A novel virtual channel matrix is introduced and an algorithm to extract localization-relevant channel parameters from its atomic norm decomposition is designed. Then, based on the extended invariance principle, a weighted least squares problem is proposed to accurately recover the location and orientation using both line-of-sight and non-line-of-sight channel informati…
This paper considers the problem of estimating the sparse mmWave massive multiple input - multiple output (MIMO) OFDM channel from one-bit quantized measurements. Unlike previous grid-based one-bit compressive sensing approaches, we present a gridless convex method to recover sparse channel form one-bit measurements via Binary Atomic Norm Minimization (BiANM) and Reweighted Binary Atomic Norm Minimization (ReBiANM). Simulation results verify the accuracy of the binary and reweighted binary atomic norm minimization techniques.
We consider the channel estimation problem in point-to-point reconfigurable intelligent surface (RIS)-aided millimeter-wave (mmWave) MIMO systems. By exploiting the low-rank nature of mmWave channels in the angular domains, we propose a non-iterative Two-stage RIS-aided Channel Estimation (TRICE) framework, where every stage is formulated as a multidimensional direction-of-arrival (DOA) estimation problem. As a result, our TRICE framework is very general in the sense that any efficient multidimensional DOA estimation solution can be readily used in every stage to estimate the associated channe…
Beamspace multi-input multi-output (MIMO) relying on lens antenna arrays can significantly reduce the number of radio-frequency chains in millimeter-wave (mmWave) communication systems through beam selection. However, the beamforming gain is actually frequency-dependent in wideband mmWave MIMO systems. This phenomenon is called beam squint, which will deteriorate the system's performance when traditional beam selection methods are used. To solve this problem, we propose a wideband beam selection method for mmWave MIMO systems relying on lens antenna arrays. Firstly, we select one beam with the…
