Millimeter wave (mmWave) band, or high frequencies such as THz, has large undeveloped band of spectrum. However, wireless channels over the mmWave band usually have one or two paths only due to the severe attenuation. The channel property restricts its development in the multiple-input multiple-output (MIMO) system, which can improve throughput by increasing the spectral efficiency. Recent development in reconfigurable intelligent surface (RIS) provides new opportunities to mmWave communications. In this study, we propose a mmWave system, which used low-precision analog-to-digital converters (ADCs), with the aid of several RIS arrays. Moreover, each RIS array has many reflectors with discrete phase shift. By employing the linear spatial processing, these arrays form a synthetic channel with increased spatial diversity and power gain, which can support MIMO transmission. We develop a MIMO detector according to the characteristics of the synthetic channel. RIS arrays can provide spatial diversity to support MIMO transmission, however, different number, antenna configuration, and deployment of RIS arrays affect the bit error rate (BER) performance. We present state evolution (SE) equations to evaluate the BER of the proposed MIMO detector in the different cases. The BER performance of indoor system is studied extensively through leveraging by the SE equations. We reveal numerous insights about the RIS effects and discuss the appropriate system settings. In addition, our results demonstrate that the low-cost hardware, such as the 3-bit ADCs of the receiver side and the 2-bit uniform discrete phase shift of the RIS arrays, only moderately degenerate the system performance.
Multiple-input multiple-output (MIMO) signaling is one of the key technologies of current mobile communication systems. However, the complex and expensive radio frequency (RF) chains have always limited the increase of MIMO scale. In this paper, we propose a MIMO transmission architecture based on a dual-polarized reconfigurable intelligent surface (RIS), which can directly achieve modulation and transmission of multichannel signals without the need for conventional RF chains. Compared with previous works, the proposed architecture can improve the integration of RIS-based transmission systems.…
Reconfigurable multiple-input multiple-output can provide performance gains over traditional MIMO by reshaping the channels, i.e., introducing more channel realizations. In this paper, we focus on the achievable rate maximization pattern design for reconfigurable MIMO systems. Firstly, we introduce the matrix representation of pattern reconfigurable MIMO (PR-MIMO), based on which a pattern design problem is formulated. To further reveal the effect of the radiation pattern on the wireless channel, we consider pattern design for both the single-pattern case where the optimized radiation pattern …
This paper investigates the maximal achievable rate for a given average error probability and blocklength for the reconfigurable intelligent surface (RIS) assisted multiple-input and multiple-output (MIMO) system. The result consists of a finite blocklength channel coding achievability bound and a converse bound based on the Berry-Esseen theorem, the Mellin transform and the mutual information. Numerical evaluation shows fast speed of convergence to the maximal achievable rate as the blocklength increases and also proves that the channel variance is a sound measurement of the backoff from the …
Reconfigurable intelligent surface (RIS)-based transmission technology offers a promising solution to enhance wireless communication performance cost-effectively through properly adjusting the parameters of a large number of passive reflecting elements. This letter proposes a cosine similarity theorem-based low-complexity algorithm for adapting the phase shifts of an RIS that assists a multiple-input multiple-output (MIMO) transmission system. A semi-analytical probabilistic approach is developed to derive the theoretical average bit error probability (ABEP) of the system. Furthermore, the val…
This paper investigates the performance of reconfigurable intelligent surface (RIS)-aided massive multiple-input multiple-output (MIMO) systems with direct links, and the phase shifts of the RIS are designed based on the statistical channel state information (CSI). We first derive the closed-form expression of the uplink ergodic data rate. Then, based on the derived expression, we use the genetic algorithm (GA) to solve the sum data rate maximization problem. With low-complexity maximal-ratio combination (MRC) and low-overhead statistical CSI-based scheme, we validate that the RIS can still br…
Cell-free systems can effectively eliminate the inter-cell interference by enabling multiple base stations (BSs) to cooperatively serve users without cell boundaries at the expense of high costs of hardware and power sources due to the large-scale deployment of BSs. To tackle this issue, the low-cost reconfigurable intelligent surface (RIS) can serve as a promising technique to improve the energy efficiency of cell-free systems. In this paper, we consider an RIS aided cell-free MIMO system where multiple RISs are deployed around BSs and users to create favorable propagation conditions via reco…
The performance of millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems is limited by the sparse nature of propagation channels and the restricted number of radio frequency (RF) chains at transceivers. The introduction of reconfigurable antennas offers an additional degree of freedom on designing mmWave MIMO systems. This paper provides a theoretical framework for studying the mmWave MIMO with reconfigurable antennas. Based on the virtual channel model, we present an architecture of reconfigurable mmWave MIMO with beamspace hybrid analog-digital beamformers and reconfigurable…
We consider a reconfigurable intelligent surface (RIS)-aided massive multi-user multiple-input multiple-output (MIMO) communication system with transceiver hardware impairments (HWIs) and RIS phase noise. Different from the existing contributions, the phase shifts of the RIS are designed based on the long-term angle informations. Firstly, an approximate analytical expression of the uplink achievable rate is derived. Then, we use genetic algorithm (GA) to maximize the sum rate and the minimum date rate. Finally, we show that it is crucial to take HWIs into account when designing the phase shift…
Massive multiple-input multiple-output (MIMO) and reconfigurable intelligent surface (RIS) are two promising technologies for 5G-and-beyond wireless networks, capable of providing large array gain and multiuser spatial multiplexing. Without requiring additional frequency bands, those technologies offer significant improvements in both spectral and energy efficiency by simultaneously serving many users. The performance analysis of an RIS-assisted Massive MIMO system as a function of the channel statistics relies heavily on fundamental properties including favorable propagation, channel hardenin…
The key obstacle to achieving the full potential of the millimeter wave (mmWave) band has been the poor propagation characteristics of wireless signals in this band. One approach to overcome this issue is to use antennas that can support higher gains while providing beam adaptability and diversity, i.e., reconfigurable antennas. In this article, we present a new architecture for mmWave multiple-input multiple-output (MIMO) communications that uses a new class of reconfigurable antennas. More specifically, the proposed lens-based antennas can support multiple radiation patterns while using a si…
Reconfigurable antennas (RAs) are a promising technology to enhance the capacity and coverage of wireless communication systems. However, RA systems have two major challenges: (i) High computational complexity of mode selection, and (ii) High overhead of channel estimation for all modes. In this paper, we develop a low-complexity iterative mode selection algorithm for data transmission in an RA-MIMO system. Furthermore, we study channel estimation of an RA multi-user MIMO system. However, given the coherence time, it is challenging to estimate channels of all modes. We propose a mode selection…
The K-user multiple-input and multiple-output (MIMO) broadcast channel (BC) with no channel state information at the transmitter (CSIT) is considered, where each receiver is assumed to be equipped with reconfigurable antennas capable of choosing a subset of receiving modes from several preset modes. Under general antenna configurations, the sum linear degrees of freedom (LDoF) of the K-user MIMO BC with reconfigurable antennas is completely characterized, which corresponds to the maximum sum DoF achievable by linear coding strategies. The LDoF region is further characterized for a class of ant…
Full Duplex (FD) communication can revolutionize wireless communications as it avoids using independent channels for bi-directional communications. This work generalizes the point-to-point FD communication in millimeter wave (mmWave) band consisting of K-pairs of massive MIMO FD nodes operating simultaneously. We present a novel joint hybrid beamforming (HYBF) and combining scheme for weighted sum-rate (WSR) maximization to enable the coexistence of massive MIMO FD links cost-efficiently. The proposed algorithm relies on alternative optimization based on the minorization-maximization method. M…
The large spectrum available in the millimeter-Wave (mmWave) band has emerged as a promising solution for meeting the huge capacity requirements of the 5th generation (5G) wireless networks. However, to fully harness the potential of mmWave communications, obstacles such as severe path loss, channel sparsity and hardware complexity should be overcome. In this paper, we introduce a generalized reconfigurable antenna multiple-input multiple-output (MIMO) architecture that takes advantage of lens-based reconfigurable antennas. The considered antennas can support multiple radiation patterns simult…
The densely packed antennas of millimeter-Wave (mmWave) MIMO systems are often blocked by the rain, snow, dust and even by fingers, which will change the channel's characteristics and degrades the system's performance. In order to solve this problem, we propose a cross-entropy inspired antenna array diagnosis detection (CE-AAD) technique by exploiting the correlations of adjacent antennas, when blockages occur at the transmitter. Then, we extend the proposed CE-AAD algorithm to the case, where blockages occur at transmitter and receiver simultaneously. Our simulation results show that the prop…
We propose a space-frequency (SF) block coding scheme for a multiple-input multiple-output (MIMO) orthogonal frequency-division multiplexing (OFDM) system using antennas with reconfigurable radiation patterns. In this system, each element of the antenna array at the transmitter side is assumed to be reconfigurable so that it can independently change the physical characteristics of its radiation pattern. The proposed block code is full rate and benefits from spatial, frequency, and reconfigurable radiation pattern state diversity over frequency-selective fading channels. We provide simulation r…
Wireless backhaul is considered to be the key part of the future wireless network with dense small cell traffic and high capacity demand. In this paper, we focus on the design of a high spectral efficiency line-of-sight (LoS) multiple-input multiple-output (MIMO) system for millimeter wave (mmWave) backhaul using dual-polarized frequency division duplex (FDD). High spectral efficiency is very challenging to achieve for the system due to various physical impairments such as phase noise (PHN), timing offset (TO) as well as the poor condition number of the LoS MIMO. In this paper, we propose a ho…
This article aims to reduce huge pilot overhead when estimating the reconfigurable intelligent surface (RIS) relayed wireless channel. Motivated by the compelling grasp of deep learning in tackling nonlinear mapping problems, the proposed approach only activates a part of RIS elements and utilizes the corresponding cascaded channel estimate to predict another part. Through a synthetic deep neural network (DNN), the direct channel and active cascaded channel are first estimated sequentially, followed by the channel prediction for the inactive RIS elements. A three-stage training strategy is dev…
Beam training based on hierarchical codebook for millimeter wave (mmWave) massive MIMO is investigated. Unlike the existing work using the same hierarchical codebook to estimate different multi-path components (MPCs), dynamic hierarchical codebooks which are updated according to the estimated MPCs are adopted. Firstly, a generalized hierarchical codebook design method is proposed. Then based on this method, a beam training method which dynamically updates the hierarchical codebook by removing the contribution of the estimated MPCs from the codebook is proposed. Simulation results verify the ef…
We investigate a reconfigurable intelligent surface (RIS)-aided multi-user massive multiple-input multi-output (MIMO) system where low-resolution digital-analog converters (DACs) are configured at the base station (BS) in order to reduce the cost and power consumption. An approximate analytical expression for the downlink achievable rate is derived based on maximum ratio transmission (MRT) and additive quantization noise model (AQNM), and the rate maximization problem is solved by particle swarm optimization (PSO) method under both continuous phase shifts (CPSs) and discrete phase shifts (DPSs…
The highly sparse nature of propagation channels and the restricted use of radio frequency (RF) chains at transceivers limit the performance of millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems. Introducing reconfigurable antennas to mmWave can offer an additional degree of freedom on designing mmWave MIMO systems. This paper provides a theoretical framework for studying the mmWave MIMO with reconfigurable antennas. We present an architecture of reconfigurable mmWave MIMO with beamspace hybrid analog-digital beamformers and reconfigurable antennas at both the transmitter a…
Reconfigurable intelligent surfaces (RISs) have emerged as a promising technique to enhance the system spectral efficiency. This paper investigates the ergodic channel capacity (ECC) of an RIS-aided multiple-input multiple-output channel under the assumption that the transmitter-RIS, RIS-receiver, and transmitter-receiver channels contain deterministic line-of-sight paths. Novel expressions are derived to characterize the upper and lower bounds of the ECC. To unveil more system insights, asymptotic analyses are performed to the system ECC in the limit of large signal-to-noise ratio (SNR) and n…
This work discusses the optimal reconfigurable intelligent surface placement in highly-directional millimeter wave links. In particular, we present a novel system model that takes into account the relationship between the transmission beam footprint at the RIS plane and the RIS size. Subsequently, based on the model we derive the end-to-end expression of the received signal power and, furthermore, provide approximate closed-form expressions in the case that the RIS size is either much smaller or at least equal to the transmission beam footprint. Moreover, building upon the expressions, we deri…
Reconfigurable intelligent surface (RIS) is a new paradigm that has great potential to achieve cost-effective, energy-efficient information modulation for wireless transmission, by the ability to change the reflection coefficients of the unit cells of a programmable metasurface. Nevertheless, the electromagnetic responses of the RISs are usually only phase-adjustable, which considerably limits the achievable rate of RIS-based transmitters. In this paper, we propose an RIS architecture to achieve amplitude-and-phase-varying modulation, which facilitates the design of multiple-input multiple-out…
We analyze the diversity gain for a distributed antenna subarray employing orthogonal frequency-division multiplexing (OFDM) in millimeter-wave (mm-Wave) massive multiple-input multiple-output (MIMO) systems. We show that the diversity gain depends on the number of transmitted data streams, the number of remote antenna units, and the number of propagation paths between RAUs. Furthermore, we show that by using bit-interleaved coded multiple beamforming (BICMB), one can achieve the maximum diversity gain in a distributed antenna subarray system. The assumption in both scenarios is that the numbe…
Measurement results for millimeter wave LOS MIMO systems are presented with a focus on time variation and multipath propagation. Different system setups are used, including 2x2 and 3x3 MIMO, and involving different synchronization procedures and front-ends. Furthermore, different propagation scenarios are evaluated, covering a wide area of applications. The results show that the LOS component carries significantly more power than the NLOS components, and that frequency selectivity from front-ends should be taken into account when designing these high bandwidth systems. Frequency offsets and ot…
Millimeter-wave links are of a line-of-sight nature. Hence, multiple-input multiple-output (MIMO) systems operating in the millimeter-wave band may not achieve full spatial diversity or multiplexing. In this paper, we utilize reconfigurable antennas and the high antenna directivity in the millimeter-wave band to propose a rate-two space coding design for 2x2 MIMO systems. The proposed scheme can be decoded with a low complexity maximum-likelihood detector at the receiver and yet it can enhance the bit-error-rate performance of millimeter-wave systems compared to traditional spatial multiplexin…
Massive multiple-input multiple-out (MIMO) technology is vital in millimeter-wave (mmWave) bands to obtain large array gains. However, there are practical challenges, such as high hardware cost and power consumption in such systems. A promising solution to these problems is to adopt a hybrid beamforming architecture. This architecture has a much lower number of transceiver (TRx) chains than the total antenna number, resulting in cost- and energy-efficient systems. In this paper, we present a real-time mmWave (28 GHz) massive MIMO testbed with hybrid beamforming. This testbed has a 64-antenna/1…
This letter investigates the reconfigurable intelligent surface (RIS)-aided massive multiple-input multiple-output (MIMO) systems with a two-timescale design. First, the zero-forcing (ZF) detector is applied at the base station (BS) based on instantaneous aggregated CSI, which is the superposition of the direct channel and the cascaded user-RIS-BS channel. Then, by leveraging the channel statistical property, we derive the closed-form ergodic achievable rate expression. Using a gradient ascent method, we design the RIS passive beamforming only relying on the long-term statistical CSI. We prove…
Millimeter-wave (mmWave) channels, which occupy frequency ranges much higher than those being used in previous wireless communications systems, are utilized to meet the increased throughput requirements that come with 5G communications. The high levels of attenuation experienced by electromagnetic waves in these frequencies causes MIMO channels to have high spatial correlation. To attain desirable error performances, systems require knowledge about the channel correlations. In this thesis, a deep neural network aided method is proposed for the parametric estimation of the channel covariance ma…
Millimeter-wave (mmWave) multiple-input multiple-output (MIMO) system for the fifth generation (5G) cellular communications can also enable single-anchor positioning and object tracking due to its large bandwidth and inherently high angular resolution. In this paper, we introduce the newly invented concept, large intelligent surface (LIS), to mmWave positioning systems, study the theoretical performance bounds (i.e., Cramér-Rao lower bounds) for positioning, and evaluate the impact of the number of LIS elements and the value of phase shifters on the position estimation accuracy compared to the…
Holographic Multiple Input Multiple Output (HMIMO), which integrates massive antenna elements into a compact space to achieve a spatially continuous aperture, plays an important role in future wireless networks. With numerous antenna elements, it is hard to implement the HMIMO via phased arrays due to unacceptable power consumption. To address this issue, reconfigurable refractive surface (RRS) is an energy efficient enabler of HMIMO since the surface is free of expensive phase shifters. Unlike traditional metasurfaces working as passive relays, the RRS is used as transmit antennas, where the …
Reconfigurable intelligent surface (RIS)-assisted communications appear as a promising candidate for future wireless systems due to its attractive advantages in terms of implementation cost and end-to-end system performance. In this paper, two new multiple-input multiple-output (MIMO) system designs using RISs are presented to enhance the performance and boost the spectral efficiency of state-of-the-art MIMO communication systems. Vertical Bell Labs layered space-time (VBLAST) and Alamouti's schemes have been considered in this study and RIS-based simple transceiver architectures are proposed.…
In this paper, a framework of beamspace channel estimation in millimeter wave (mmWave) massive MIMO system is proposed. The framework includes the design of hybrid precoding and combining matrix as well as the search method for the largest entry of over-sampled beamspace receiving matrix. Then based on the framework, three channel estimation schemes including identity matrix approximation (IA)-based scheme, scattered zero off-diagonal (SZO)-based scheme and concentrated zero off-diagonal (CZO)-based scheme are proposed. These schemes together with the existing channel estimation schemes are co…
We consider channel/subspace tracking systems for temporally correlated millimeter wave (e.g., E-band) multiple-input multiple-output (MIMO) channels. Our focus is given to the tracking algorithm in the non-line-of-sight (NLoS) environment, where the transmitter and the receiver are equipped with hybrid analog/digital precoder and combiner, respectively. In the absence of straightforward time-correlated channel model in the millimeter wave MIMO literature, we present a temporal MIMO channel evolution model for NLoS millimeter wave scenarios. Considering that conventional MIMO channel tracking …
Intelligent reflecting surfaces (IRSs) are regarded as promising enablers for future millimeter wave (mmWave) wireless communication, due to their ability to create favorable line-of-sight (LoS) propagation environments. In this paper, we investigate channel estimation in downlink IRS-assisted mmWave multiple-input multiple-output (MIMO) systems. By leveraging the sparsity of mmWave channels, we formulate the channel estimation problem as a fixed-rank constrained non-convex optimization problem. To tackle the non-convexity, an efficient algorithm is proposed by capitalizing on alternating mini…
Reconfigurable intelligent surface (RIS) is considered to be an energy-efficient approach to reshape the wireless environment for improved throughput. Its passive feature greatly reduces the energy consumption, which makes RIS a promising technique for enabling the future smart city. Existing beamforming designs for RIS mainly focus on optimizing the spectral efficiency for single carrier systems. To avoid the complicated bit allocation on different spatial domain subchannels in MIMO systems, in this paper, we propose a geometric mean decomposition-based beamforming for RIS-assisted millimeter…
This paper presents LuMaMi28, a real-time 28 GHz massive multiple-input multiple-output (MIMO) testbed. In this testbed, the base station has 16 transceiver chains with a fully-digital beamforming architecture (with different pre-coding algorithms) and simultaneously supports multiple user equipments (UEs) with spatial multiplexing. The UEs are equipped with a beam-switchable antenna array for real-time antenna selection where the one with the highest channel magnitude, out of four pre-defined beams, is selected. For the beam-switchable antenna array, we consider two kinds of UE antennas, with…
We consider a two--tile reconfigurable intelligent surface (RIS) assisted wireless network with a two-antenna transmitter and receiver over Rayleigh fading. We show that the average received signal-to-noise-ratio (SNR) optimal transmission and combining vectors are given by the left and right singular spaces of the RIS-receiver and transmit-RIS channel matrices, respectively. Moreover, the optimal phases at the two tiles of the RIS are determined by the phases of the elements of the latter spaces. To further study the effect of phase compensation, we statistically characterize the average SNR …
Beamforming is indispensable in the operation of 60-GHz millimeter-wave directional multi-gigabit Wi-Fi. Simple power method and its extensions enable the transmitting and receiving antenna arrays to form a beam for single spatial stream. To further improve the spectral efficiency in future 60-GHz directional Wi-Fi, alternating least square (ALS) algorithm can form multiple beams between the transmitter and receiver for multi-input-multi-output (MIMO) operations. For both shared and split MIMO architecture, the ALS beamforming algorithm can be operated in both frequency-flat and frequency-sele…
Aiming at maximizing the achievable sum-rate of wideband multiuser mmWave massive MIMO systems, the hybrid precoding is studied. Since each computation of the achievable sum-rate can be performed only after the analog precoder and digital precoder are both determined, the maximization of the achievable sum-rate has intractable computational complexity. By introducing the interference free (IF) achievable sum-rate, the design of the analog and digital precoders can be decoupled. To avoid the beam conflict and maximize the IF achievable sum-rate, a Hungarian-based codeword selection algorithm is…
We consider a multiple-input multiple-output (MIMO) channel in the presence of a reconfigurable intelligent surface (RIS). Specifically, our focus is on analyzing the spatial multiplexing gains in line-of-sight and low-scattering MIMO channels in the near field. We prove that the channel capacity is achieved by diagonalizing the end-to-end transmitter-RIS-receiver channel, and applying the water-filling power allocation to the ordered product of the singular values of the transmitter-RIS and RIS-receiver channels. The obtained capacity-achieving solution requires an RIS with a non-diagonal mat…
We propose a holographic version of a reconfigurable intelligent surface (RIS) and investigate its application to terahertz (THz) massive multiple-input multiple-output systems. Capitalizing on the miniaturization of THz electronic components, RISs can be implemented by densely packing sub-wavelength unit cells, so as to realize continuous or quasi-continuous apertures and to enable holographic communications. In this paper, in particular, we derive the beam pattern of a holographic RIS. Our analysis reveals that the beam pattern of an ideal holographic RIS can be well approximated by that of …
Using out-of-band (OOB) side-information has recently been shown to accelerate beam selection in single-user millimeter wave (mmWave) massive MIMO communications. In this paper, we propose a novel OOB-aided beam selection framework for a mmWave uplink multi-user system. In particular, we exploit spatial information extracted from lower (sub-6 GHz) bands in order to assist with an inter-user coordination scheme at mmWave bands. To enforce coordination, we propose an exchange protocol exploiting device-to-device communications, where low-rate beam-related information is exchanged between the mob…
In this letter, we consider hybrid beamforming for millimeter wave (mmWave) MIMO integrated sensing and communications (ISAC). We design the transmit beam of a dual-functional radar-communication (DFRC) base station (BS), aiming at approaching the objective radar beam pattern, subject to the constraints of the signal to interference-plus-noise ratio (SINR) of communication users and total transmission power of the DFRC BS. To provide additional degree of freedom for the beam design problem, we introduce a phase vector to the objective beam pattern and propose an alternating minimization method…
As communication systems that employ millimeter wave (mmWave) frequency bands must use large antenna arrays to overcome the severe propagation loss of mmWave signals, hybrid beamforming has been considered as an integral component of mmWave communications. Recently, intelligent reflecting surface (IRS) has been proposed as an innovative technology that can significantly improve the performance of mmWave communication systems through the use of low-cost passive reflecting elements. In this paper, we study IRS-aided mmWave multiple-input multiple-output (MIMO) systems with hybrid beamforming arc…
In recent years there has been a growing interest in reconfigurable intelligent surfaces (RISs) as enablers for the realization of smart radio propagation environments which can provide performance improvements with low energy consumption in future wireless networks. However, to reap the potential gains of RIS it is crucial to jointly design both the transmit precoder and the phases of the RIS elements. Within this context, in this paper we study the use of multiple RIS panels in a parallel or multi-hop configuration with the aim of assisting a multi-stream multiple-input multiple-output (MIMO…
This paper establishes an upper bound on the capacity of line-of-sight multiantenna channels over all possible antenna arrangements and shows that uniform linear arrays (ULAs) with an SNR-dependent rotation of transmitter or receiver can closely approach such capacity---and in fact achieve it at low and high SNR, and asymptotically in the numbers of antennas. Then, as an alternative to mechanically rotating ULAs, we propose to electronically select among multiple ULAs having a radial disposition at either transmitter or receiver, and we bound the shortfall from capacity as a function of the nu…
In this paper, we propose a full-rate full-diversity space-time block code (STBC) for 2x2 reconfigurable multiple-input multiple-output (MIMO) systems that require a low complexity maximum likelihood (ML) detector. We consider a transmitter equipped with a linear antenna array where each antenna element can be independently configured to create a directive radiation pattern toward a selected direction. This property of transmit antennas allow us to increase the data rate of the system, while reducing the computational complexity of the receiver. The proposed STBC achieves a coding rate of two …
Delay alignment modulation (DAM) is a novel wideband communication technique, which exploits the high spatial resolution and multi-path sparsity of millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems to mitigate inter-symbol interference (ISI), without relying on conventional techniques like channel equalization or multi-carrier transmission. In this paper, we extend the DAM technique to multi-user mmWave massive MIMO communication systems. We first provide asymptotic analysis by showing that when the number of base station (BS) antennas is much larger than the total…
In multiple-input multiple-output (MIMO) device-to-device (D2D) networks, interference and rank-deficient channels are the critical bottlenecks for achieving high degrees of freedom (DoFs). In this paper, we propose a reconfigurable intelligent surface (RIS) assisted interference alignment strategy to simultaneous mitigate the co-channel interference and cope with rank-deficient channels, thereby improving the feasibility of interference alignment conditions and in turn increasing the achievable DoFs. The key enabler is a general low-rank optimization approach that maximizes the achievable DoF…
This paper focuses on channel estimation for mmWave MIMO systems with 1-bit spatial sigma-delta analog-to-digital converters (ADCs). The channel estimation performance with 1-bit spatial sigma-delta ADCs depends on the quantization noise modeling. Therefore, we present a new method for modeling the quantization noise by leveraging the deterministic input-output relation of the 1-bit spatial sigma-delta ADC. Using this new noise model, we propose an algorithm for channel estimation for a narrowband single-user mmWave line-of-sight MIMO system by determining the unknown angles and path attenuati…
