Intelligent reflecting surfaces (IRSs) are regarded as promising enablers for future millimeter wave (mmWave) wireless communication, due to their ability to create favorable line-of-sight (LoS) propagation environments. In this paper, we investigate channel estimation in downlink IRS-assisted mmWave multiple-input multiple-output (MIMO) systems. By leveraging the sparsity of mmWave channels, we formulate the channel estimation problem as a fixed-rank constrained non-convex optimization problem. To tackle the non-convexity, an efficient algorithm is proposed by capitalizing on alternating minimization and manifold optimization (MO), which yields a locally optimal solution. Simulation results show that the proposed MO-based estimation (MO-EST) algorithm significantly outperforms two benchmark schemes and demonstrate the robustness of the MO-EST algorithm with respect to imperfect knowledge of the sparsity level of the channels in practical implementations.
Full Duplex (FD) communication can revolutionize wireless communications as it avoids using independent channels for bi-directional communications. This work generalizes the point-to-point FD communication in millimeter wave (mmWave) band consisting of K-pairs of massive MIMO FD nodes operating simultaneously. We present a novel joint hybrid beamforming (HYBF) and combining scheme for weighted sum-rate (WSR) maximization to enable the coexistence of massive MIMO FD links cost-efficiently. The proposed algorithm relies on alternative optimization based on the minorization-maximization method. M…
The densely packed antennas of millimeter-Wave (mmWave) MIMO systems are often blocked by the rain, snow, dust and even by fingers, which will change the channel's characteristics and degrades the system's performance. In order to solve this problem, we propose a cross-entropy inspired antenna array diagnosis detection (CE-AAD) technique by exploiting the correlations of adjacent antennas, when blockages occur at the transmitter. Then, we extend the proposed CE-AAD algorithm to the case, where blockages occur at transmitter and receiver simultaneously. Our simulation results show that the prop…
Wireless backhaul is considered to be the key part of the future wireless network with dense small cell traffic and high capacity demand. In this paper, we focus on the design of a high spectral efficiency line-of-sight (LoS) multiple-input multiple-output (MIMO) system for millimeter wave (mmWave) backhaul using dual-polarized frequency division duplex (FDD). High spectral efficiency is very challenging to achieve for the system due to various physical impairments such as phase noise (PHN), timing offset (TO) as well as the poor condition number of the LoS MIMO. In this paper, we propose a ho…
Beam training based on hierarchical codebook for millimeter wave (mmWave) massive MIMO is investigated. Unlike the existing work using the same hierarchical codebook to estimate different multi-path components (MPCs), dynamic hierarchical codebooks which are updated according to the estimated MPCs are adopted. Firstly, a generalized hierarchical codebook design method is proposed. Then based on this method, a beam training method which dynamically updates the hierarchical codebook by removing the contribution of the estimated MPCs from the codebook is proposed. Simulation results verify the ef…
In this work, we propose a new single-RF MIMO architecture which enjoys high scalability and energy-efficiency. The transmitter in this proposal consists of a single RF illuminator radiating towards a reflecting surface. Each element on the reflecting surface re-transmits its received signal after applying a phase-shift, such that a desired beamforming pattern is obtained. For this architecture, the problem of beamforming is interpreted as linear regression and a solution is derived via the method of least-squares. Using this formulation, a fast iterative algorithm for tuning of the reflecting…
We analyze the diversity gain for a distributed antenna subarray employing orthogonal frequency-division multiplexing (OFDM) in millimeter-wave (mm-Wave) massive multiple-input multiple-output (MIMO) systems. We show that the diversity gain depends on the number of transmitted data streams, the number of remote antenna units, and the number of propagation paths between RAUs. Furthermore, we show that by using bit-interleaved coded multiple beamforming (BICMB), one can achieve the maximum diversity gain in a distributed antenna subarray system. The assumption in both scenarios is that the numbe…
Measurement results for millimeter wave LOS MIMO systems are presented with a focus on time variation and multipath propagation. Different system setups are used, including 2x2 and 3x3 MIMO, and involving different synchronization procedures and front-ends. Furthermore, different propagation scenarios are evaluated, covering a wide area of applications. The results show that the LOS component carries significantly more power than the NLOS components, and that frequency selectivity from front-ends should be taken into account when designing these high bandwidth systems. Frequency offsets and ot…
Reducing computational complexity is crucial in optimizing the phase shifts of Intelligent Reflecting Surface (IRS) systems since IRS-assisted communication systems are generally deployed with a large number of reflecting elements (REs). This letter proposes a low-complexity algorithm, designated as Dimension-wise Sinusoidal Maximization (DSM), to obtain the optimal IRS phase shifts that maximize the sum capacity of a MIMO network. The algorithm exploits the fact that the objective function for the optimization problem is sinusoidal w.r.t. the phase shift of each RE. The numerical results show…
Massive multiple-input multiple-out (MIMO) technology is vital in millimeter-wave (mmWave) bands to obtain large array gains. However, there are practical challenges, such as high hardware cost and power consumption in such systems. A promising solution to these problems is to adopt a hybrid beamforming architecture. This architecture has a much lower number of transceiver (TRx) chains than the total antenna number, resulting in cost- and energy-efficient systems. In this paper, we present a real-time mmWave (28 GHz) massive MIMO testbed with hybrid beamforming. This testbed has a 64-antenna/1…
Millimeter-wave (mmWave) channels, which occupy frequency ranges much higher than those being used in previous wireless communications systems, are utilized to meet the increased throughput requirements that come with 5G communications. The high levels of attenuation experienced by electromagnetic waves in these frequencies causes MIMO channels to have high spatial correlation. To attain desirable error performances, systems require knowledge about the channel correlations. In this thesis, a deep neural network aided method is proposed for the parametric estimation of the channel covariance ma…
Millimeter-wave (mmWave) multiple-input multiple-output (MIMO) system for the fifth generation (5G) cellular communications can also enable single-anchor positioning and object tracking due to its large bandwidth and inherently high angular resolution. In this paper, we introduce the newly invented concept, large intelligent surface (LIS), to mmWave positioning systems, study the theoretical performance bounds (i.e., Cramér-Rao lower bounds) for positioning, and evaluate the impact of the number of LIS elements and the value of phase shifters on the position estimation accuracy compared to the…
Cell-free massive multiple-input multiple-output (MIMO) and intelligent reflecting surface (IRS) are considered as the prospective multiple antenna technologies for beyond the fifth-generation (5G) networks. Cell-free MIMO systems powered by IRSs, combining both technologies, can further improve the performance of cell-free MIMO systems at low cost and energy consumption. Prior works focused on instantaneous performance metrics and relied on alternating optimization algorithms, which impose huge computational complexity and signaling overhead. To address these challenges, we propose a novel tw…
We consider channel/subspace tracking systems for temporally correlated millimeter wave (e.g., E-band) multiple-input multiple-output (MIMO) channels. Our focus is given to the tracking algorithm in the non-line-of-sight (NLoS) environment, where the transmitter and the receiver are equipped with hybrid analog/digital precoder and combiner, respectively. In the absence of straightforward time-correlated channel model in the millimeter wave MIMO literature, we present a temporal MIMO channel evolution model for NLoS millimeter wave scenarios. Considering that conventional MIMO channel tracking …
In this paper, a downlink intelligent reflecting surface (IRS) enhanced millimeter-wave (mmWave) non-orthogonal multiple access (NOMA) system is considered. A joint optimization problem over active beamforming, passive beamforming and power allocation is formulated. Due to the highly coupled variables, the formulated optimization problem is non-convex. To solve this problem, an alternative optimization and successive convex approximation based iterative algorithm is proposed. Numerical results illustrate that: 1) the proposed scheme offers significant sum-rate gains, which confirms the effecti…
In this paper, a framework of beamspace channel estimation in millimeter wave (mmWave) massive MIMO system is proposed. The framework includes the design of hybrid precoding and combining matrix as well as the search method for the largest entry of over-sampled beamspace receiving matrix. Then based on the framework, three channel estimation schemes including identity matrix approximation (IA)-based scheme, scattered zero off-diagonal (SZO)-based scheme and concentrated zero off-diagonal (CZO)-based scheme are proposed. These schemes together with the existing channel estimation schemes are co…
This work studies the modelling and the optimization of intelligent reflecting surface (IRS) assisted multiple-input multiple-output (MIMO) systems through cascaded line-of-sight (LoS) links. In Part I of this work, we build up a new IRS-aided MIMO channel model, named the cascaded LoS MIMO channel. The proposed channel model consists of a transmitter (Tx) and a receiver (Rx) both equipped with uniform linear arrays, and an IRS is used to enable communications between the transmitter and the receiver through the LoS links seen by the IRS. When modeling the reflection of electromagnetic waves a…
Beamforming is indispensable in the operation of 60-GHz millimeter-wave directional multi-gigabit Wi-Fi. Simple power method and its extensions enable the transmitting and receiving antenna arrays to form a beam for single spatial stream. To further improve the spectral efficiency in future 60-GHz directional Wi-Fi, alternating least square (ALS) algorithm can form multiple beams between the transmitter and receiver for multi-input-multi-output (MIMO) operations. For both shared and split MIMO architecture, the ALS beamforming algorithm can be operated in both frequency-flat and frequency-sele…
Millimeter-wave links are of a line-of-sight nature. Hence, multiple-input multiple-output (MIMO) systems operating in the millimeter-wave band may not achieve full spatial diversity or multiplexing. In this paper, we utilize reconfigurable antennas and the high antenna directivity in the millimeter-wave band to propose a rate-two space coding design for 2x2 MIMO systems. The proposed scheme can be decoded with a low complexity maximum-likelihood detector at the receiver and yet it can enhance the bit-error-rate performance of millimeter-wave systems compared to traditional spatial multiplexin…
This paper presents LuMaMi28, a real-time 28 GHz massive multiple-input multiple-output (MIMO) testbed. In this testbed, the base station has 16 transceiver chains with a fully-digital beamforming architecture (with different pre-coding algorithms) and simultaneously supports multiple user equipments (UEs) with spatial multiplexing. The UEs are equipped with a beam-switchable antenna array for real-time antenna selection where the one with the highest channel magnitude, out of four pre-defined beams, is selected. For the beam-switchable antenna array, we consider two kinds of UE antennas, with…
Aiming at maximizing the achievable sum-rate of wideband multiuser mmWave massive MIMO systems, the hybrid precoding is studied. Since each computation of the achievable sum-rate can be performed only after the analog precoder and digital precoder are both determined, the maximization of the achievable sum-rate has intractable computational complexity. By introducing the interference free (IF) achievable sum-rate, the design of the analog and digital precoders can be decoupled. To avoid the beam conflict and maximize the IF achievable sum-rate, a Hungarian-based codeword selection algorithm is…
As communication systems that employ millimeter wave (mmWave) frequency bands must use large antenna arrays to overcome the severe propagation loss of mmWave signals, hybrid beamforming has been considered as an integral component of mmWave communications. Recently, intelligent reflecting surface (IRS) has been proposed as an innovative technology that can significantly improve the performance of mmWave communication systems through the use of low-cost passive reflecting elements. In this paper, we study IRS-aided mmWave multiple-input multiple-output (MIMO) systems with hybrid beamforming arc…
Using out-of-band (OOB) side-information has recently been shown to accelerate beam selection in single-user millimeter wave (mmWave) massive MIMO communications. In this paper, we propose a novel OOB-aided beam selection framework for a mmWave uplink multi-user system. In particular, we exploit spatial information extracted from lower (sub-6 GHz) bands in order to assist with an inter-user coordination scheme at mmWave bands. To enforce coordination, we propose an exchange protocol exploiting device-to-device communications, where low-rate beam-related information is exchanged between the mob…
In this letter, we consider hybrid beamforming for millimeter wave (mmWave) MIMO integrated sensing and communications (ISAC). We design the transmit beam of a dual-functional radar-communication (DFRC) base station (BS), aiming at approaching the objective radar beam pattern, subject to the constraints of the signal to interference-plus-noise ratio (SINR) of communication users and total transmission power of the DFRC BS. To provide additional degree of freedom for the beam design problem, we introduce a phase vector to the objective beam pattern and propose an alternating minimization method…
Delay alignment modulation (DAM) is a novel wideband communication technique, which exploits the high spatial resolution and multi-path sparsity of millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems to mitigate inter-symbol interference (ISI), without relying on conventional techniques like channel equalization or multi-carrier transmission. In this paper, we extend the DAM technique to multi-user mmWave massive MIMO communication systems. We first provide asymptotic analysis by showing that when the number of base station (BS) antennas is much larger than the total…
This paper focuses on channel estimation for mmWave MIMO systems with 1-bit spatial sigma-delta analog-to-digital converters (ADCs). The channel estimation performance with 1-bit spatial sigma-delta ADCs depends on the quantization noise modeling. Therefore, we present a new method for modeling the quantization noise by leveraging the deterministic input-output relation of the 1-bit spatial sigma-delta ADC. Using this new noise model, we propose an algorithm for channel estimation for a narrowband single-user mmWave line-of-sight MIMO system by determining the unknown angles and path attenuati…
Use of low resolution analog to digital converters (ADCs) is an effective way to reduce the high power consumption of millimeter wave (mmWave) receivers. In this paper, a receiver with low resolution ADCs based on adaptive thresholds is considered in downlink mmWave communications in which the channel state information is not known a-priori and acquired through channel estimation. A performance comparison of low-complexity algorithms for power and ADC allocation among transmit and receive terminals, respectively, is provided. Through simulation of practical mmWave cellular networks, it is show…
Millimeter Wave (mmWave) band provides a large spectrum to meet the high-demand capacity by the 5th generation (5G) wireless networks. However, to fully exploit the available spectrum, obstacles such as high path loss, channel sparsity, and hardware complexity should be overcome. To this end, the present paper aims to design a new multiple-input multiple-output (MIMO) system using lens-based multi-beam reconfigurable antennas. The proposed MIMO system uses complete lens at the transmitter and incomplete lens at the receiver. To reduce hardware complexity, we utilize an optimal beam selection t…
In this paper we present measurement results for pure line-of-sight MIMO links operating in the millimeter wave range. We show that the estimated condition numbers and capacities of the measured channels are in good agreement with the theory for various transmission distances and antenna setups. Furthermore, the results show that orthogonal channel vectors can be observed if the spacing criterion is fulfilled, thus facilitating spatial multiplexing and achieving high spectral efficiencies even over fairly long distances. Spacings generating ill-conditioned channel matrices show on the other ha…
Intelligent reflecting surface (IRS) is a promising solution to enhance the wireless communication capacity both cost-effectively and energy-efficiently, by properly altering the signal propagation via tuning a large number of passive reflecting units. In this paper, we aim to characterize the fundamental capacity limit of IRS-aided point-to-point multiple-input multiple-output (MIMO) communication systems with multi-antenna transmitter and receiver in general, by jointly optimizing the IRS reflection coefficients and the MIMO transmit covariance matrix. First, we consider narrowband transmiss…
A hybrid architecture for millimeter wave (mmW) massive MIMO systems is considered practically implementable due to low power consumption and high energy efficiency. However, due to the limited number of RF chains, user selection becomes necessary for such architecture. Traditional user selection algorithms suffer from high computational complexity and, therefore, may not be scalable in 5G and beyond wireless mobile communications. To address this issue, in this letter we propose a low complexity CNN framework for user selection. The proposed CNN accepts as input the channel matrix and gives a…
The high energy consumption of massive multi-input multi-out (MIMO) system has become a prominent problem in the millimeter wave(mm-Wave) communication scenario. The hybrid precoding technology greatly reduces the number of radio frequency(RF) chains by handing over part of the coding work to the phase shifting network, which can effectively improve energy efficiency. However, conventional hybrid precoding algorithms based on mathematical means often suffer from performance loss and high computational complexity. In this paper, a novel BP-neural-network-enabled hybrid precoding algorithm is pr…
We address the problem of analyzing and classifying in groups the downlink channel environment in a millimeter-wavelength cell, accounting for path loss, multipath fading, and User Equipment (UE) blocking, by employing a hybrid propagation and multipath fading model, thus using accurate inter-group interference modeling. The base station (BS) employs a large Uniform Planar Array (UPA) to facilitate massive Multiple-Input, Multiple-Output (MIMO) communications with high efficiency. UEs are equipped with a single antenna and are distributed uniformly within the cell. The key problem is analyzing…
In this paper, channel estimation techniques and phase shift design for intelligent reflecting surface (IRS)-empowered single-user multiple-input multiple-output (SU-MIMO) systems are proposed. Among four channel estimation techniques developed in the paper, the two novel ones, single-path approximated channel (SPAC) and selective emphasis on rank-one matrices (SEROM), have low training overhead to enable practical IRS-empowered SU-MIMO systems. SPAC is mainly based on parameter estimation by approximating IRS-related channels as dominant single-path channels. SEROM exploits IRS phase shifts a…
Recent applications of the Full Duplex (FD) technology focus on enabling simultaneous control communication and data transmission to reduce the control information exchange overhead, which impacts end-to-end latency and spectral efficiency. In this paper, we present a simultaneous direction estimation and data transmission scheme for millimeter Wave (mmWave) massive Multiple-Input Multiple-Output (MIMO) systems, enabled by a recent FD MIMO technology with reduced hardware complexity Self-Interference (SI) cancellation. We apply the proposed framework in the mmWave analog beam management proble…
Mobility and blockage are two critical challenges in wireless transmission over millimeter-wave (mmWave) and Terahertz (THz) bands. In this paper, we investigate network massive multiple-input multiple-output (MIMO) transmission for mmWave/THz downlink in the presence of mobility and blockage. Considering the mmWave/THz propagation characteristics, we first propose to apply per-beam synchronization for network massive MIMO to mitigate the channel Doppler and delay dispersion effects. Accordingly, we establish a transmission model. We then investigate network massive MIMO downlink transmission …
Millimeter wave (mmWave) band, or high frequencies such as THz, has large undeveloped band of spectrum. However, wireless channels over the mmWave band usually have one or two paths only due to the severe attenuation. The channel property restricts its development in the multiple-input multiple-output (MIMO) system, which can improve throughput by increasing the spectral efficiency. Recent development in reconfigurable intelligent surface (RIS) provides new opportunities to mmWave communications. In this study, we propose a mmWave system, which used low-precision analog-to-digital converters (…
Finite resolution analog beamforming (FRAB) has been recognized as an effective approach to reduce hardware costs in massive multiple-input multiple-output (MIMO) and millimeter-wave networks. However, the use of FRAB means that the beamformers are not perfectly aligned with the users' channels and multiple users may be assigned similar or even identifical beamformers. This letter shows how non-orthogonal multiple access (NOMA) can be used to exploit this feature of FRAB, where a single FRAB based beamformer is shared by multiple users. Both analytical and simulation results are provided to de…
An intelligent reflecting surface (IRS), consisting of reconfigurable metamaterials, can be used to partially control the radio environment and thereby bring new features to wireless communications. Previous works on IRS have particularly studied the range extension use case and under what circumstances the new technology can beat relays. In this paper, we study another use case that might have a larger impact on the channel capacity: rank improvement. One of the classical bottlenecks of point-to-point MIMO communications is that the capacity gains provided by spatial multiplexing are only lar…
Nowadays, millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems is a favorable candidate for the fifth generation (5G) cellular systems. However, a key challenge is the high power consumption imposed by its numerous radio frequency (RF) chains, which may be mitigated by opting for low-resolution analog-to-digital converters (ADCs), whilst tolerating a moderate performance loss. In this article, we discuss several important issues based on the most recent research on mmWave massive MIMO systems relying on low-resolution ADCs. We discuss the key transceiver design challe…
Reconfigurable intelligent surface (RIS) is considered to be an energy-efficient approach to reshape the wireless environment for improved throughput. Its passive feature greatly reduces the energy consumption, which makes RIS a promising technique for enabling the future smart city. Existing beamforming designs for RIS mainly focus on optimizing the spectral efficiency for single carrier systems. To avoid the complicated bit allocation on different spatial domain subchannels in MIMO systems, in this paper, we propose a geometric mean decomposition-based beamforming for RIS-assisted millimeter…
Channel estimation in reconfigurable intelligent surface (RIS) assisted multiple input multiple output (MIMO) communication systems is challenging as pilots cannot be decoded at or transmitted from a RIS with only passive elements. We assume an angular model for the line-of-sight channel between the user equipment (UE) and the RIS and between the RIS and the base station (BS) with no direct path between the UE and BS. In this letter, assuming that we can compute the RIS-BS channel (up to a complex path gain) from their known locations, we first discuss the ambiguity involved in estimating the …
The performance of millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems is limited by the sparse nature of propagation channels and the restricted number of radio frequency (RF) chains at transceivers. The introduction of reconfigurable antennas offers an additional degree of freedom on designing mmWave MIMO systems. This paper provides a theoretical framework for studying the mmWave MIMO with reconfigurable antennas. Based on the virtual channel model, we present an architecture of reconfigurable mmWave MIMO with beamspace hybrid analog-digital beamformers and reconfigurable…
Millimeter wave (mmWave) and terahertz MIMO systems rely on pre-defined beamforming codebooks for both initial access and data transmission. However, most of the existing codebooks adopt pre-defined beams that focus mainly on improving the gain of their target users, without taking interference into account, which could incur critical performance degradation in dense networks. To address this problem, in this paper, we propose a sample-efficient digital twin-assisted beam pattern design framework that learns how to form the beam pattern to reject the signals from the interfering directions. Th…
In a practical massive MIMO (multiple-input multiple-output) system, the number of antennas at a base station (BS) is constrained by the space and cost factors, which limits the throughput gain promised by theoretical analysis. This paper thus studies the feasibility of adopting the intelligent reflecting surface (IRS) to further improve the beamforming gain of the uplink communications in a massive MIMO system. Under such a novel system, the central question lies in whether the IRS is able to enhance the network throughput as expected, if the channel estimation overhead is taken into account.…
In this letter, we investigate the energy efficiency (EE) problem in a millimeter wave (mmWave) massive MIMO (mMIMO) system with non-orthogonal multiple access (NOMA). Multiple two-user clusters are formulated according to their channel correlation and gain difference. Following this, we propose a hybrid analog/digital precoding scheme for the low radio frequency (RF) chains structure at the base station (BS). On this basis, we formulate a power allocation problem aiming to maximize the EE under users' quality of service (QoS) requirements and per-cluster power constraint. An iterative algorit…
In this work, the uplink channel estimation problem is considered for a millimeter wave (mmWave) multi-input multi-output (MIMO) system. It is well known that pilot overhead and computation complexity in estimating the channel increases with the number of antennas and the bandwidth. To overcome this, the proposed approach allows the channel estimation at the base station to be aided by the sensing information. The sensing information contains an estimate of scatterers locations in an environment. A simultaneous weighting orthogonal matching pursuit (SWOMP) - sparse Bayesian learning (SBL) algo…
In this letter, the achievable rate maximization problem is considered for intelligent reflecting surface (IRS) assisted multiple-input multiple-output (MIMO) systems in an underlay spectrum sharing scenario, subject to interference power constraints at the primary users. The formulated non-convex optimization problem is challenging to solve due to its non-convexity as well as coupling design variables in the constraints. Different from existing works that are mostly based on alternating optimization (AO), we propose a penalty dual decomposition based gradient projection (PDDGP) algorithm to s…
With the capability of reconfiguring the wireless electromagnetic environment, intelligent reflecting surface (IRS) is a new paradigm for designing future wireless communication systems. In this paper, we consider optical IRS for improving the performance of visible light communication (VLC) under a multiple-input and multiple-output (MIMO) setting. Specifically, we focus on the downlink communication of an indoor MIMO VLC system and aim to minimize the mean square error (MSE) of demodulated signals at the receiver. To this end, the MIMO channel gain of the IRS-aided VLC is first derived under…
This work is devoted to solve the problem of estimating the carrier frequency offset, phase offset, amplitude, and SNR between two mmWave transceivers. The Cramér-Rao Lower Bound (CRLB) for the different parameters is provided first, as well as the condition for the CRLB to exist, known as Regularity Condition. Thereafter, the problem of finding suitable estimators for the parameters is adressed, for which the proposed solution is the Maximum Likelihood estimator (ML).
This paper proposes the use of subspace tracking algorithms for performing MIMO channel estimation at millimeter wave (mmWave) frequencies. Using a subspace approach, we develop a protocol enabling the estimation of the right (resp. left) singular vectors at the transmitter (resp. receiver) side; then, we adapt the projection approximation subspace tracking with deflation (PASTd) and the orthogonal Oja (OOJA) algorithms to our framework and obtain two channel estimation algorithms. The hybrid analog/digital nature of the beamformer is also explicitly taken into account at the algorithm design …
Intelligent reflecting surface (IRS) is a cost-efficient technique to improve power efficiency and spectral efficiency. However, IRS-aided multi-antenna transmission needs to jointly optimize the passive and active beamforming, imposing a high computational burden and high latency due to its iterative optimization process. Making use of hybrid analog-digital beamforming in high-frequency transmission systems, a novel technique, coined dual-beam IRS, is proposed in this paper. The key idea is to form a pair of beams towards the IRS and user, respectively. Then, the optimization of passive and a…
In this paper, we study the problem of joint active and passive beamforming for intelligent reflecting surface (IRS)-assisted massive MIMO systems, where multiple IRSs equipped with a large number of passive elements are deployed to assist a base station (BS) to simultaneously serve a small number of single-antenna users in the same time-frequency resource. Our objective is to maximize the minimum signal to interference plus noise (SINR) at users by jointly optimizing the transmit precoding vector at the BS and phase shift parameters at IRSs. We show that an interesting automatic interference …
Hybrid analog/digital precoding allows millimeter wave MIMO systems to leverage large antenna array gains while permitting low cost and power consumption hardware. Most prior work has focused on hybrid precoding for narrow-band mmWave systems. MmWave systems, however, will likely operate on wideband channels with frequency selectivity. Therefore, this paper considers frequency selective hybrid precoding with RF beamforming vectors taken from a quantized codebook. For this system, a low-complexity yet near-optimal greedy algorithm is developed for the design of the hybrid analog/digital precode…
In this paper, we investigate a multi-cell millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) network with low-precision analog-to-digital converters (ADCs) at the base station (BS). Each cell serves multiple users and each user is equipped with multiple antennas but driven by a single RF chain. We first introduce a channel estimation strategy for the mmWave massive MIMO network and analyze the achievable rate with imperfect channel state information. Then, we derive an insightful lower bound for the achievable rate, which becomes tight with a growing number of users. The b…
Millimeter wave offers high bandwidth for air-to-air (A2A) communication. In this paper, we evaluate the rate performance of a multiuser MIMO (MU-MIMO) configuration where several aircraft communicate with a central hub. We consider a hybrid subarray architecture, single path channels, and realistic atmospheric attenuation effects. We propose a mathematical framework for the analysis of millimeter wave (mmWave) MU-MIMO networks. Via Monte Carlo simulation, we demonstrate that mmWave is a promising technology for delivering gigabit connectivity in next-generation aerial networks.
Machine learning tools are finding interesting applications in millimeter wave (mmWave) and massive MIMO systems. This is mainly thanks to their powerful capabilities in learning unknown models and tackling hard optimization problems. To advance the machine learning research in mmWave/massive MIMO, however, there is a need for a common dataset. This dataset can be used to evaluate the developed algorithms, reproduce the results, set benchmarks, and compare the different solutions. In this work, we introduce the DeepMIMO dataset, which is a generic dataset for mmWave/massive MIMO channels. The …
In this paper, adaptive pilot beam sequence design for channel estimation in large millimeter-wave (mmWave) MIMO systems is considered. By exploiting the sparsity of mmWave MIMO channels with the virtual channel representation and imposing a Markovian random walk assumption on the physical movement of the line-of-sight (LOS) and reflection clusters, it is shown that the sparse channel estimation problem in large mmWave MIMO systems reduces to a sequential detection problem that finds the locations and values of the non-zero-valued bins in a two-dimensional rectangular grid, and the optimal ada…
We investigate beam training and allocation for multiuser millimeter wave massive MIMO systems. An orthogonal pilot based beam training scheme is first developed to reduce the number of training times, where all users can simultaneously perform the beam training with the base station (BS). As the number of users increases, the same beam from the BS may point to different users, leading to beam conflict and multiuser interference. Therefore, a quality-of-service (QoS) constrained (QC) beam allocation scheme is proposed to maximize the equivalent channel gain of the QoS-satisfied users, under th…
