Use of low resolution analog to digital converters (ADCs) is an effective way to reduce the high power consumption of millimeter wave (mmWave) receivers. In this paper, a receiver with low resolution ADCs based on adaptive thresholds is considered in downlink mmWave communications in which the channel state information is not known a-priori and acquired through channel estimation. A performance comparison of low-complexity algorithms for power and ADC allocation among transmit and receive terminals, respectively, is provided. Through simulation of practical mmWave cellular networks, it is shown that the use of low resolution ADCs does not significantly degrade the system throughput (as compared to a conventional fully digital high resolution receiver) when using the adaptive threshold receiver in conjunction with simple power and ADC allocation strategies.
This paper focuses on channel estimation in single-user and multi-user MIMO systems with multi-antenna base stations equipped with 1-bit spatial sigma-delta analog-to-digital converters (ADCs). A careful selection of the quantization voltage level and phase shift used in the feedback loop of 1-bit sigma-delta ADCs is critical to improve its effective resolution. We first develop a quantization noise model for 1-bit spatial sigma-delta ADCs. Using the developed noise model, we then present a two-step channel estimation algorithm to estimate a multipath channel parameterized by the gains, angles…
In this article, we investigate channel estimation for wideband millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) under hybrid architecture with lowprecision analog-to-digital converters (ADCs). To design channel estimation for the hybrid structure, both analog processing components and frequency-selective digital combiners need to be optimized. The proposed channel estimator follows the typical linear-minimum-mean-square-error (LMMSE) structure and applies for an arbitrary channel model. Moreover, for sparsity channels as in mmWave, the proposed estimator performs more ef…
Advances in analog-to-digital converter (ADC) technology have opened up the possibility to directly digitize wideband radio frequency (RF) signals, avoiding the need for analog down-conversion. In this work, we consider an orthogonal frequency-division multiplexing (OFDM)-based massive multi-user (MU) multiple-input multiple-output (MIMO) uplink system that relies on direct RF-sampling at the base station and digitizes the received RF signals with 1-bit ADCs. Using Bussgang's theorem, we provide an analytical expression for the error-vector magnitude (EVM) achieved by digital down-conversion a…
Analog to Digital Converters (ADCs) are a major contributor to the energy consumption on the receiver side of millimeter-wave multiple-input multiple-output (MIMO) systems with large antenna arrays. Consequently, there has been significant interest in using low-resolution ADCs along with hybrid beam-forming at MIMO receivers for energy efficiency. However, decreasing the ADC resolution results in performance loss -- in terms of achievable rates -- due to increased quantization error. In this work, we study the application of practically implementable nonlinear analog operations, prior to sampl…
This paper considers the channel estimation problem for massive multiple-input multiple-output (MIMO) systems that use one-bit analog-to-digital converters (ADCs). Previous channel estimation techniques for massive MIMO using one-bit ADCs are all based on single-shot estimation without exploiting the inherent temporal correlation in wireless channels. In this paper, we propose an adaptive channel estimation technique taking the spatial and temporal correlations into account for massive MIMO with one-bit ADCs. We first use the Bussgang decomposition to linearize the one-bit quantized received s…
In this article, deep learning is applied to estimate the uplink channels for mixed analog-to-digital converters (ADCs) massive multiple-input multiple-output (MIMO) systems, where a portion of antennas are equipped with high-resolution ADCs while others employ low-resolution ones at the base station. A direct-input deep neural network (DI-DNN) is first proposed to estimate channels by using the received signals of all antennas. To eliminate the adverse impact of the coarsely quantized signals, a selective-input prediction DNN (SIP-DNN) is developed, where only the signals received by the high…
Millimeter wave (mmWave) massive multiple-input multiple-output (massive MIMO) is one of the most promising technologies for the fifth generation and beyond wireless communication system. However, a large number of antennas incur high power consumption and hardware costs, and high-frequency communications place a heavy burden on the analog-to-digital converters (ADCs) at the base station (BS). Furthermore, it is too costly to equipping each antenna with a high-precision ADC in a large antenna array system. It is promising to adopt low-resolution ADCs to address this problem. In this paper, we …
This paper proposes the Newtonized fully corrective forward greedy selection-cross validation-based (NFCFGS-CV-based) channel estimator for millimeter (mmWave) hybrid massive multiple-input multiple-output (MIMO) systems with low-resolution analog-to-digital converters (ADCs). The proposed NFCFGS algorithm is a gridless compressed sensing (CS) technique that combines the FCFGS and Newtonized orthogonal matching pursuit (NOMP) algorithms. In particular, NFCFGS performs single path estimation over the continuum at each iteration based on the previously estimated paths. The CV technique is adopte…
This paper considers a multiple-input multiple-output (MIMO) system with low-resolution analog-to-digital converters (ADCs). In this system, the paper presents a new MIMO detection approach using coding theory. The principal idea of the proposed approach is to transform a non-linear MIMO channel to a linear MIMO channel by leveraging both a $p$-level quantizer and a lattice code where $p\geq 2$. After transforming to the linear MIMO channel with the sets of finite input and output elements, efficient MIMO detection methods are proposed to attain both diversity and multiplexing gains by using a…
In this paper, the fully corrective forward greedy selection-cross validation-based (FCFGS-CV-based) channel estimator is proposed for wideband millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems with low-resolution analog-to-digital converters (ADCs). The sparse nature of the mmWave virtual channel in the angular and delay domains is exploited to convert the maximum a posteriori (MAP) channel estimation problem to an optimization problem with a concave objective function and sparsity constraint. The FCFGS algorithm, which is the generalized orthogonal matching pursu…
The low-resolution analog-to-digital convertor (ADC) is a promising solution to significantly reduce the power consumption of radio frequency circuits in massive multiple-input multiple-output (MIMO) systems. In this letter, we investigate the uplink spectral efficiency (SE) of massive MIMO systems with low-resolution ADCs over Rician fading channels, where both perfect and imperfect channel state information are considered. By modeling the quantization noise of low-resolution ADCs as an additive quantization noise, we derive tractable and exact approximation expressions of the uplink SE of ma…
The combination of orthogonal frequency modulation (OFDM) and multiple-input multiple-output (MIMO) systems plays an important role in modern communication systems. In order to meet the growing throughput demands, future MIMO-OFDM receivers are expected to utilize a massive number of antennas, operate in dynamic environments, and explore high frequency bands, while satisfying strict constraints in terms of cost, power, and size. An emerging technology to realize massive MIMO receivers of reduced cost and power consumption is based on dynamic metasurface antennas (DMAs), which inherently implem…
The use of low-resolution analog-to-digital converters (ADCs) is considered to be an effective technique to reduce the power consumption and hardware complexity of wireless transceivers. However, in systems with low-resolution ADCs, obtaining channel state information (CSI) is difficult due to significant distortions in the received signals. The primary motivation of this paper is to show that learning techniques can mitigate the impact of CSI unavailability. We study the blind detection problem in multiple-input-multiple-output (MIMO) systems with low-resolution ADCs using learning approaches…
High hardware cost and high power consumption of massive multiple-input and multiple output (MIMO) are two challenges for the future wireless communications including beyond fifth generation (B5G) and sixth generation (6G). Adopting the low-resolution analog-to-digital converter (ADC) is viewed as a promising solution. Additionally, the direction of arrival (DOA) estimation is an indispensable technology for beam alignment and tracking in massive MIMO systems. Thus, in this paper, the performance of DOA estimation with mixed-ADC structure is firstly investigated. The Cramer-Rao lower bound (CR…
Analog-to-digital converters (ADCs) stand for a significant part of the total power consumption in a massive MIMO base station. One-bit ADCs are one way to reduce power consumption. This paper presents an analysis of the spectral efficiency of single-carrier and OFDM transmission in massive MIMO systems that use one-bit ADCs. A closed-form achievable rate, i.e., a lower bound on capacity, is derived for a wideband system with a large number of channel taps that employs low-complexity linear channel estimation and symbol detection. Quantization results in two types of error in the symbol detect…
One way to reduce the power consumption in large-scale multiple-input multiple-output (MIMO) systems is to employ low-resolution analog-to-digital converters (ADCs). In this paper, we investigate antenna selection for large-scale MIMO receivers with low-resolution ADCs, thereby providing more flexibility in resolution and number of ADCs. To incorporate quantization effects, we generalize an existing objective function for a greedy capacity-maximization antenna selection approach. The derived objective function offers an opportunity to select an antenna with the best tradeoff between the additi…
We consider channel estimation for an uplink massive multiple-input multiple-output (MIMO) system where the base station (BS) uses an array with low-resolution (1-2 bit) analog-to-digital converters and a spatial Sigma-Delta ($ΣΔ$) architecture to shape the quantization noise away from users in some angular sector. We develop a linear minimum mean squared error (LMMSE) channel estimator based on the Bussgang decomposition that reformulates the nonlinear quantizer model using an equivalent linear model plus quantization noise. We also analyze the uplink achievable rate with maximal ratio combin…
In this paper, we present a successive-cancellation-soft-output (SCSO) detector for an uplink multiuser multiple-input-multiple-output (MU-MIMO) system with one-bit analog-to-digital converters (ADCs). The proposed detector produces soft outputs (e.g., log-likelihood ratios (LLRs)) from one-bit quantized observations in a successive way: each user k's message is sequentially decoded from a channel decoder $k$ for $k=1,...,K$ in that order, and the previously decoded messages are exploited to improve the reliabilities of LLRs. Furthermore, we develop an efficient greedy algorithm to optimize a …
Nowadays, millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems is a favorable candidate for the fifth generation (5G) cellular systems. However, a key challenge is the high power consumption imposed by its numerous radio frequency (RF) chains, which may be mitigated by opting for low-resolution analog-to-digital converters (ADCs), whilst tolerating a moderate performance loss. In this article, we discuss several important issues based on the most recent research on mmWave massive MIMO systems relying on low-resolution ADCs. We discuss the key transceiver design challe…
This paper considers uplink massive MIMO systems with 1-bit analog-to-digital converters (ADCs) and develops a deep-learning based channel estimation framework. In this framework, the prior channel estimation observations and deep neural network models are leveraged to learn the non-trivial mapping from quantized received measurements to channels. For that, we derive the sufficient length and structure of the pilot sequence to guarantee the existence of this mapping function. This leads to the interesting, and \textit{counter-intuitive}, observation that when more antennas are employed by the …
Employing low-resolution analog-to-digital converters (ADCs) for millimeter wave receivers with large antenna arrays provides opportunity to efficiently reduce power consumption of the receiver. Reducing ADC resolution, however, results in performance degradation due to non-negligible quantization error. In addition, the large number of radio frequency (RF) chains is still not desirable. Accordingly, conventional low-resolution ADC systems require more efficient designs to minimize the cost and complexity while maximizing performance. In this article, we discuss advanced low-resolution ADC rec…
This letter considers the architecture of distributed antenna system, which is made up of a massive number of single-antenna remote radio heads (RRHs), some with full-resolution but others with low-resolution analog-to-digital converter (ADC) receivers. This architecture is greatly motivated by its high energy efficiency and low-cost implementation. We derive the worst-case uplink spectral efficiency (SE) of the system assuming a frequency-flat channel and maximum-ratio combining (MRC), and reveal that the SE increases as the number of quantization bits for the low-resolution ADCs increases, a…
In this paper, a channel estimator for wideband millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems with hybrid architectures and low-resolution analog-to-digital converters (ADCs) is proposed. To account for the propagation delay across the antenna array, which cannot be neglected in wideband mmWave massive MIMO systems, the discrete time channel that models the spatial wideband effect is developed. Also, the training signal design that addresses inter-frame, inter-user, and inter-symbol interferences is investigated when the spatial wideband effect is not negligibl…
A potential tremendous spectrum resource makes millimeter wave (mmWave) communications a promising technology. High power consumption due to a large number of antennas and analog-to-digital converters (ADCs) for beamforming to overcome the large propagation losses is problematic in practice. As a hybrid beamforming architecture and low-resolution ADCs are considered to reduce power consumption, estimation of mmWave channels becomes challenging. We evaluate several channel estimation algorithms for wideband mmWave systems with hybrid beamforming and low-resolution ADCs. Through simulation, we s…
We present an analytical framework for the channel estimation and the data detection in massive multiple-input multiple-output uplink systems with 1-bit analog-to-digital converters (ADCs) and i.i.d. Rayleigh fading. First, we provide closed-form expressions of the mean squared error (MSE) of the channel estimation considering the state-of-the-art linear minimum MSE estimator and the class of scaled least-squares estimators. For the data detection, we provide closed-form expressions of the expected value and the variance of the estimated symbols when maximum ratio combining is adopted, which c…
In this paper, channel estimation for millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems with one-bit analog-to-digital converters (ADCs) is considered. In the mmWave band, the number of propagation paths is small, which results in sparse virtual channels. To estimate sparse virtual channels based on the maximum a posteriori (MAP) criterion, sparsity-constrained optimization comes into play. In general, optimizing objective functions with sparsity constraints is NP-hard because of their combinatorial complexity. Furthermore, the coarse quantization of one-bit ADCs m…
In this paper, we derive a closed-form expression for the combiner of a multiple-input-multiple-output (MIMO) receiver equipped with a minimum-mean-square-error (MMSE) estimator. We propose using variable-bit-resolution analog-to- digital converters (ADC) across radio frequency (RF) paths. The combiner designed is a function of the quantization errors across each RF path. Using very low bit resolution ADCs (1-2bits) is a popular approach with massive MIMO receiver architectures to mitigate large power demands. We show that for certain channel conditions, adopting unequal bit resolution ADCs (e…
We develop a broadband channel estimation algorithm for millimeter wave (mmWave) multiple input multiple output (MIMO) systems with few-bit analog-to-digital converters (ADCs). Our methodology exploits the joint sparsity of the mmWave MIMO channel in the angle and delay domains. We formulate the estimation problem as a noisy quantized compressed-sensing problem and solve it using efficient approximate message passing (AMP) algorithms. In particular, we model the angle-delay coefficients using a Bernoulli-Gaussian-mixture distribution with unknown parameters and use the expectation-maximization…
High resolution analog to digital converters (ADCs) are conventionally used at the receiver terminals to store an accurate digital representation of the received signal, thereby allowing for reliable decoding of transmitted messages. However, in a wide range of applications, such as communication over millimeter wave and massive multiple-input multiple-output (MIMO) systems, the use of high resolution ADCs is not feasible due to power budget limitations. In the conventional fully digital receiver design, where each receiver antenna is connected to a distinct ADC, reducing the ADC resolution le…
In millimeter wave (mmWave) systems, we investigate uplink user scheduling when a basestation employs low-resolution analog-to-digital converters (ADCs) with a large number of antennas. To reduce power consumption in the receiver, low-resolution ADCs can be a potential solution for mmWave systems in which many antennas are likely to be deployed to compensate for the large path loss. Due to quantization error, we show that the channel structure in the beamspace, in addition to the channel magnitude and beamspace orthogonality, plays a key role in maximizing the achievable rates of scheduled use…
The fundamental limits of communication over multiple-input multiple-output (MIMO) networks are considered when a limited number of one-bit analog to digital converters (ADC) are used at the receiver terminals. Prior works have mainly focused on point-to-point communications, where receiver architectures consisting of a concatenation of an analog processing module, a limited number of one-bit ADCs with non-adaptive thresholds, and a digital processing module are considered. In this work, a new receiver architecture is proposed which utilizes adaptive threshold one-bit ADCs - where the ADC thre…
We derive an expression for the capacity of massive multiple-input multiple-output Millimeter wave (mmWave) channel where the receiver is equipped with a variable-resolution Analog to Digital Converter (ADC) and a hybrid combiner. The capacity is shown to be a function of Cramer-Rao Lower Bound (CRLB) for a given bit-allocation matrix and hybrid combiner. The condition for optimal ADC bit-allocation under a receiver power constraint is derived. This is derived based on the maximization of capacity with respect to bit-allocation matrix for a given channel, hybrid precoder, and hybrid combiner. …
This paper considers a multiple-input multiple-output (MIMO) receiver with very low-precision analog-to-digital convertors (ADCs) with the goal of developing massive MIMO antenna systems that require minimal cost and power. Previous studies demonstrated that the training duration should be {\em relatively long} to obtain acceptable channel state information. To address this requirement, we adopt a joint channel-and-data (JCD) estimation method based on Bayes-optimal inference. This method yields minimal mean square errors with respect to the channels and payload data. We develop a Bayes-optima…
We develop a method to jointly estimate the carrier frequency offset (CFO) and the narrowband channel in millimeter wave (mmWave) MIMO systems operating with one-bit analog-to-digital converters (ADCs). We assume perfect timing synchronization and transform the underlying CFO-channel optimization problem to a higher dimensional space using lifting techniques. Exploiting the sparsity of mmWave MIMO channels in the angle domain, we perform joint estimation by solving a noisy quantized compressed sensing problem of the lifted version, using generalized approximate message passing. Simulation resu…
We investigate the uplink throughput achievable by a multiple-user (MU) massive multiple-input multiple-output (MIMO) system in which the base station is equipped with a large number of low-resolution analog-to-digital converters (ADCs). Our focus is on the case where neither the transmitter nor the receiver have any a priori channel state information. This implies that the fading realizations have to be learned through pilot transmission followed by channel estimation at the receiver, based on coarsely quantized observations. We propose a novel channel estimator, based on Bussgang's decomposi…
In this paper, we investigate a multi-cell millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) network with low-precision analog-to-digital converters (ADCs) at the base station (BS). Each cell serves multiple users and each user is equipped with multiple antennas but driven by a single RF chain. We first introduce a channel estimation strategy for the mmWave massive MIMO network and analyze the achievable rate with imperfect channel state information. Then, we derive an insightful lower bound for the achievable rate, which becomes tight with a growing number of users. The b…
In order to reduce hardware complexity and power consumption, massive multiple-input multiple-output (MIMO) systems employ low-resolution analog-to-digital converters (ADCs) to acquire quantized measurements $\boldsymbol y$. This poses new challenges to the channel estimation problem, and the sparse prior on the channel coefficient vector $\boldsymbol x$ in the angle domain is often used to compensate for the information lost during quantization. By interpreting the sparse prior from a probabilistic perspective, we can assume $\boldsymbol x$ follows certain sparse prior distribution and recove…
The use of low precision (e.g., 1-3 bits) analog-to-digital convenors (ADCs) in very large multiple-input multiple-output (MIMO) systems is a technique to reduce cost and power consumption. In this context, nevertheless, it has been shown that the training duration is required to be {\em very large} just to obtain an acceptable channel state information (CSI) at the receiver. A possible solution to the quantized MIMO systems is joint channel-and-data (JCD) estimation. This paper first develops an analytical framework for studying the quantized MIMO system using JCD estimation. In particular, w…
In this paper, we present a new scenario of direction of arrival (DOA) estimation using massive multiple-input multiple-output (MIMO) receive array with low-resolution analog-to-digital convertors (ADCs), which can strike a good balance between performance and circuit cost. Based on the linear additive quantization noise model (AQNM), the effect of low-resolution ADCs on the methods, such as Root-MUSIC method, is analyzed. Also, the closed-form expression of Cramer-Rao lower bound (CRLB) is derived to evaluate the performance loss caused by the low-resolution ADCs. The simulation results show …
This paper investigated the uplink of multi-user massive multi-input multi-output (MIMO) systems with a mixed analog-to-digital converter (ADC) receiver architecture, in which some antennas are equipped with costly full-resolution ADCs and others with less expensive low-resolution ADCs. A closed-form approximation of the achievable spectral efficiency (SE) with the maximum-ratio combining (MRC) detector is derived. Based on this approximated result, the effects of the number of base station antennas, the transmit power, the proportion of full-resolution ADCs in the mixed-ADC structure, and the…
Communication systems with low-resolution analog-to-digital-converters (ADCs) can exploit channel state information at the transmitter and receiver. This paper presents codebook designs and performance analyses for limited feedback MIMO systems with finite-bit ADCs. A point-to-point single-user channel is firstly considered. When the received signal is sliced by 1-bit ADCs, the absolute phase at the receiver is important to align the phase of the received signals. A new codebook design for beamforming, which separately quantizes the channel direction and the residual phase, is therefore propos…
The use of low-precision analog-to-digital converters (ADCs) is a low-cost and power-efficient solution for a millimeter wave (mmWave) multiple-input multiple-output (MIMO) system operating at sampling rates higher than a few Gsample/sec. This solution, however, can make significant frame-error-rates (FERs) degradation due to inter-subcarrier interference when applying conventional frequency-domain equalization techniques. In this paper, we propose computationally-efficient yet near-optimal soft-output detection methods for the coded mmWave MIMO systems with low-precision ADCs. The underlying …
We study an uplink multiuser multiple-input multiple-output (MU-MIMO) system with one-bit analog-to-digital converters (ADCs). For such system, a supervised-learning (SL) detector has been recently proposed by modeling a non-linear end-to-end system function into a parameterized Bernoulli-like model. Despite its attractive performance, the SL detector requires a large amount of labeled data (i.e., pilot signals) to estimate the parameters of the underlying model accurately. This is because the amount of the parameters grows exponentially with the number of users. To overcome this drawback, we …
In millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems, one-bit analog-to-digital converters (ADCs) are employed to reduce the impractically high power consumption, which is incurred by the wide bandwidth and large arrays. In practice, the mmWave band consists of a small number of paths, thereby rendering sparse virtual channels. Then, the resulting maximum a posteriori (MAP) channel estimation problem is a sparsity-constrained optimization problem, which is NP-hard to solve. In this paper, iterative approximate MAP channel estimators for mmWave massive MIMO systems …
This paper considers uplink massive multiple-input multiple-output (MIMO) systems with lowresolution analog-to-digital converters (ADCs) over Rician fading channels. Maximum-ratio-combining (MRC) and zero-forcing (ZF) receivers are considered under the assumption of perfect and imperfect channel state information (CSI). Low-resolution ADCs are considered for both data detection and channel estimation, and the resulting performance is analyzed. Asymptotic approximations of the spectrum efficiency (SE) for large systems are derived based on random matrix theory. With these results, we can provid…
Institut National de la Recherche Scientifique (INRS-EMT)（加拿大魁北克大学国家科学研究院（电磁与电信研究所））
In this paper, we propose a multi-layer artificial neural network (ANN) that is trained with the Levenberg-Marquardt algorithm for use in signal detection over multiple-input multiple-output orthogonal frequency-division multiplexing (MIMO-OFDM) systems, particularly those with low-resolution analog-to-digital converters (LR-ADCs). We consider a blind detection scheme where data symbol estimation is carried out without knowing the channel state information at the receiver (CSIR)---in contrast to classical algorithms. The main power of the proposed ANN-based detector (ANND) lies in its versatil…
In this paper, we investigate the massive MIMO relay system, where the relay station (RS) forwards the signals from multiple remote users to the base station (BS). Large-scale antenna arrays in conjunction with low-resolution analog-to-digital converters (ADCs) are equipped at the RS and the BS to guarantee the high spectral efficiency with low cost. Considering the ever-present spatial correlation at both the RS and the BS, we first study the canonical channel estimation process, from which a tractable equivalent form of the channel estimate is extracted for further analysis. Under these tran…
In this paper, we investigate the capacity of massive multiple-input multiple-output (MIMO) systems corrupted by complex-valued additive white Gaussian noise (AWGN) when both the transmitter and the receiver employ 1-bit digital-to-analog converters (DACs) and 1-bit analog-to-digital-converters (ADCs). As a result of 1-bit DACs and ADCs, the transmitted and received symbols, as well as the transmit- and receive-side channel state information (CSI), are assumed to be quantized to 1-bit of information. The derived results show that the capacity of the considered massive MIMO system is $2N$ and $…
This paper considers channel estimation and uplink achievable rate of the coarsely quantized massive multiple-input multiple-output (MIMO) system with radio frequency (RF) impairments. We utilize additive quantization noise model (AQNM) and extended error vector magnitude (EEVM) model to analyze the impacts of low-resolution analog-to-digital converters (ADCs) and RF impairments respectively. We show that hardware impairments cause a nonzero floor on the channel estimation error, which contraries to the conventional case with ideal hardware. The maximal-ratio combining (MRC) technique is then …
This paper considers a multipair amplify-and-forward massive MIMO relaying system with low-resolution ADCs at both the relay and destinations. The channel state information (CSI) at the relay is obtained via pilot training, which is then utilized to perform simple maximum-ratio combining/maximum-ratio transmission processing by the relay. Also, it is assumed that the destinations use statistical CSI to decode the transmitted signals. Exact and approximated closed-form expressions for the achievable sum rate are presented, which enable the efficient evaluation of the impact of key system parame…
Achieving high channel estimation accuracy and reducing hardware cost as well as power dissipation constitute substantial challenges in the design of massive multiple-input multiple-output (MIMO) systems. To resolve these difficulties, sophisticated pilot designs have been conceived for the family of energy-efficient hybrid analog-digital (HAD) beamforming architecture relying on adaptive-resolution analog-to-digital converters (RADCs). In this paper, we jointly optimize the pilot sequences, the number of RADC quantization bits and the hybrid receiver combiner in the uplink of multiuser massiv…
