Massive multiple-input multiple-out (MIMO) technology is vital in millimeter-wave (mmWave) bands to obtain large array gains. However, there are practical challenges, such as high hardware cost and power consumption in such systems. A promising solution to these problems is to adopt a hybrid beamforming architecture. This architecture has a much lower number of transceiver (TRx) chains than the total antenna number, resulting in cost- and energy-efficient systems. In this paper, we present a real-time mmWave (28 GHz) massive MIMO testbed with hybrid beamforming. This testbed has a 64-antenna/16-TRx unit for beam-selection, which can be expanded to larger array sizes in a modular way. For testing everything from baseband processing algorithms to scheduling and beam-selection in real propagation environments, we extend the capability of an existing 100-antenna/100-TRx massive MIMO testbed (below 6 GHz), built upon software-defined radio technology, to a flexible mmWave massive MIMO system.
To meet the demand of supreme data rates in terabits-per-second, the next-generation mobile system needs to exploit the abundant spectrum in the millimeter-wave and terahertz bands. However, high-frequency transmission heavily relies on large-scale antenna arrays to reap high beamforming gain, used to compensate for severe propagation loss. It raises a problem of omni-directional beamforming during the phase of initial access, where a base station is required to broadcast synchronization signals and system information to all users within its coverage. This paper proposes a novel initial beamfo…
Millimeter-wave (mm-wave) communication is a key technology for future wireless networks. To combat significant path loss and exploit the abundant mm-wave spectrum, effective beamforming is crucial. Nevertheless, conventional fully digital beamforming techniques are inapplicable, as they demand a separate radio frequency (RF) chain for each antenna element, which is costly and consumes too much energy. Hybrid beamforming is a cost-effective alternative, which can significantly reduce the hardware cost and power consumption by employing a small number of RF chains. This paper presents a holisti…
Full Duplex (FD) communication can revolutionize wireless communications as it avoids using independent channels for bi-directional communications. This work generalizes the point-to-point FD communication in millimeter wave (mmWave) band consisting of K-pairs of massive MIMO FD nodes operating simultaneously. We present a novel joint hybrid beamforming (HYBF) and combining scheme for weighted sum-rate (WSR) maximization to enable the coexistence of massive MIMO FD links cost-efficiently. The proposed algorithm relies on alternative optimization based on the minorization-maximization method. M…
To develop a low-complexity multicast beamforming method for millimeter wave communications, we first propose a channel gain estimation method in this article. We use the beam sweeping to find the best codeword and its two neighboring codewords to form a composite beam. We then estimate the channel gain based on the composite beam, which is computed off-line by minimizing the variance of beam gain within beam coverage. With the estimated channel gain, we propose a multicast beamforming design method under the max-min fair (MMF) criterion. To reduce the computational complexity, we divide the l…
In order to achieve terabits-per-second (Tbps) data rates in the sixth-generation (6G) mobile system, wireless communications are required to exploit the abundant spectrum in the millimeter-wave (mmWave) and terahertz (THz) bands. However, high-frequency transmission heavily relies on high beamforming gain to compensate for severe propagation loss. A beam-based system faces a barrier in the process of initial access, where a base station must broadcast synchronization signals and system information to all users within its coverage. Hence, this paper proposes a novel omnidirectional broadcastin…
Beamforming structures with fixed beam codebooks provide economical solutions for millimeter wave (mmWave) communications due to the low hardware cost. However, the training overhead to search for the optimal beamforming configuration is proportional to the codebook size. To improve the efficiency of beam tracking, we propose a beam tracking scheme based on the channel fingerprint database, which comprises mappings between statistical beamforming gains and user locations. The scheme tracks user movement by utilizing the trained beam configurations and estimating the gains of beam configuration…
This paper presents a comparative study on millimeter wave (mmWave) location-based analog beamforming (BF) techniques based on channel estimation. Localization and compressive sensing (CS) effectively reduces mmWave BF complexity and enhance the performance of mmWave system comparable to the conventional mmWave analog BF techniques. BF techniques based on channel state information (CSI) has high complexity in constructing mmWave channel sensing matrix using CS. Location services based techniques highly reduce this complexity by defining the area within which the user equipment (UE) mostly prob…
As communication systems that employ millimeter wave (mmWave) frequency bands must use large antenna arrays to overcome the severe propagation loss of mmWave signals, hybrid beamforming has been considered as an integral component of mmWave communications. Recently, intelligent reflecting surface (IRS) has been proposed as an innovative technology that can significantly improve the performance of mmWave communication systems through the use of low-cost passive reflecting elements. In this paper, we study IRS-aided mmWave multiple-input multiple-output (MIMO) systems with hybrid beamforming arc…
The premise of massive multiple-input multiple-output (MIMO) is based around coherent transmission and detection. Majority of the vast literature on massive MIMO presents performance evaluations over simplified statistical propagation models. All such models are drop-based and do not ensure continuity of channel parameters. In this paper, we quantify the impact of spatially consistent (SC) models on beamforming for massive MIMO systems. We focus on the downlink of a 28GHz multiuser urban microcellular scenario. Using the recently standardized Third Generation Partnership Project 38.901 SC-I pr…
In this letter, we consider hybrid beamforming for millimeter wave (mmWave) MIMO integrated sensing and communications (ISAC). We design the transmit beam of a dual-functional radar-communication (DFRC) base station (BS), aiming at approaching the objective radar beam pattern, subject to the constraints of the signal to interference-plus-noise ratio (SINR) of communication users and total transmission power of the DFRC BS. To provide additional degree of freedom for the beam design problem, we introduce a phase vector to the objective beam pattern and propose an alternating minimization method…
Millimeter wave (mmWave) communication links for 5G cellular technology require high beamforming gain to overcome channel impairments and achieve high throughput. While much work has focused on estimating mmWave channels and designing beamforming schemes, the time dynamic nature of mmWave channels quickly renders estimates stale and increases sounding overhead. We model the underlying time dynamic state space of mmWave channels and design sounding beamformers suitable for tracking in a Kalman filtering framework. Given an initial channel estimate, filtering efficiently leads to refined estimat…
This paper presents an evaluation of distortion and interference sources, namely, the harmonic distortion and antenna crosstalk, originating within a 2 x 2 millimeter-wave (mm-wave) multiple-input-multiple-output (MIMO) testbed. The experience gained through the insight into the built testbed could be fed into the design of future mm-wave massive MIMO testbeds.
In this paper, over-the-air experiments with external and internal interferences were performed using Chalmers millimeter-wave multiple-input-multiple-output testbed MATE. The resulting SINR for both interference experiments are compared and discussed.
We present a beamforming algorithm for multiuser wideband millimeter wave (mmWave) communication systems where one access point uses hybrid analog/digital beamforming while multiple user stations have phased-arrays with a single RF chain. The algorithm operates in a more general mode than others available in literature and has lower computational complexity and training overhead. Throughout the paper, we describe: i) the construction of novel beamformer sets (codebooks) with wide sector beams and narrow beams based on the orthogonality property of beamformer vectors, ii) a beamforming algorith…
Reconfigurable intelligent surface (RIS) is considered to be an energy-efficient approach to reshape the wireless environment for improved throughput. Its passive feature greatly reduces the energy consumption, which makes RIS a promising technique for enabling the future smart city. Existing beamforming designs for RIS mainly focus on optimizing the spectral efficiency for single carrier systems. To avoid the complicated bit allocation on different spatial domain subchannels in MIMO systems, in this paper, we propose a geometric mean decomposition-based beamforming for RIS-assisted millimeter…
Integrated Sensing and Communication (ISAC) has attracted substantial attraction in recent years for spectral efficiency improvement, enabling hardware and spectrum sharing for simultaneous sensing and signaling operations. In-band Full Duplex (FD) is being considered as a key enabling technology for ISAC applications due to its simultaneous transmission and reception capability. In this paper, we present an FD-based ISAC system operating at millimeter Wave (mmWave) frequencies, where a massive Multiple-Input Multiple-Output (MIMO) Base Station (BS) node employing hybrid Analog and Digital (A/…
Intelligent reflecting surface (IRS) technology offers more feasible propagation paths for millimeter-wave (mmWave) communication systems to overcome blockage than existing technologies. In this paper, we consider a downlink wireless system with the IRS and formulate a joint power allocation and beamforming design problem to maximize the weighted sum-rate, which is a multi-variable optimization problem. To solve the problem, we propose a novel alternating manifold optimization based beamforming algorithm. Simulation results show that our proposed optimization algorithm outperforms existing alg…
In this paper, a downlink intelligent reflecting surface (IRS) enhanced millimeter-wave (mmWave) non-orthogonal multiple access (NOMA) system is considered. A joint optimization problem over active beamforming, passive beamforming and power allocation is formulated. Due to the highly coupled variables, the formulated optimization problem is non-convex. To solve this problem, an alternative optimization and successive convex approximation based iterative algorithm is proposed. Numerical results illustrate that: 1) the proposed scheme offers significant sum-rate gains, which confirms the effecti…
This paper presents a 2 x 2 millimeter wave (mm-wave) multiple-input-multiple-output (MIMO) testbed that operates at around 30 GHz. The link assessment of the system operating at 26.25 GHz was carried out on a test bench, with a short communication distance between the transmitting and receiving antennas. A user-programmable, reconfigurable and real-time signal processing field-programmable gate arrays (FPGAs)-based software defined radio (SDR) system was employed as part of the testbed to validate the system-level performance for a downlink time division long-term evolution (TD-LTE) duplex sc…
Intelligent reflecting surface (IRS) is a cost-efficient technique to improve power efficiency and spectral efficiency. However, IRS-aided multi-antenna transmission needs to jointly optimize the passive and active beamforming, imposing a high computational burden and high latency due to its iterative optimization process. Making use of hybrid analog-digital beamforming in high-frequency transmission systems, a novel technique, coined dual-beam IRS, is proposed in this paper. The key idea is to form a pair of beams towards the IRS and user, respectively. Then, the optimization of passive and a…
Cell-free massive MIMO systems consist of many distributed access points with simple components that jointly serve the users. In millimeter wave bands, only a limited set of predetermined beams can be supported. In a network that consolidates these technologies, downlink analog beam selection stands as a challenging task for the network sum-rate maximization. Low-cost digital filters can improve the network sum-rate further. In this work, we propose low-cost joint designs of analog beam selection and digital filters. The proposed joint designs achieve significantly higher sum-rates than the di…
In this paper, we consider an edge cache-assisted millimeter wave cloud radio access network (C-RAN). Each remote radio head (RRH) in the C-RAN has a local cache, which can pre-fetch and store the files requested by the actuators. Multiple RRHs form a cluster to cooperatively serve the actuators, which acquire their required files either from the local caches or from the central processor via multicast fronthaul links. For such a scenario, we formulate a beamforming design problem to minimize the secure transmission delay under transmit power constraint of each RRH. Due to the difficulty of di…
In this letter, we investigate the millimeter wave (mmWave) downlink multiuser multiple-input multiple-output (MU-MIMO) system, adopting the dynamic subarray architecture at the base station and considering the multi-stream communication for each user. Aiming at maximizing the system spectral efficiency, we propose a novel hybrid beamforming design. First, assuming no inter-user interference (IUI), we easily get the optimal fully-digital beamformers and combiners using the singular value decomposition of each user channel and the waterfilling algorithm. Then, based on the obtained fullydigital…
Full Duplex (FD) radio has emerged as a promising solution to increase the data rates by up to a factor of two via simultaneous transmission and reception in the same frequency band. This paper studies a novel hybrid beamforming (HYBF) design to maximize the weighted sum-rate (WSR) in a single-cell millimeter wave (mmWave) massive multiple-input-multiple-output (mMIMO) FD system. Motivated by practical considerations, we assume that the multi-antenna users and hybrid FD base station (BS) suffer from the limited dynamic range (LDR) noise due to non-ideal hardware and an impairment aware HYBF ap…
This paper investigates the problem of increasing the security at the physical layer of a Millimeter Wave (mmWave) network equipped with several Intelligent Reflecting Surfaces (IRSs). In this network, multiple IRSs help the Base Station (BS) to reach the signal to the desired user and at the same time maintain the security of the network i.e. securing the signal from receiving by the unallowable eavesdropper. The target of the proposed scheme is to maximize the secrecy rate by jointly optimizing the active beamforming at the BS and passive beamforming at the IRSs. This leads to a non-convex o…
This paper investigates the application of non-orthogonal multiple access in millimeter-Wave communications (mmWave-NOMA). Particularly, we consider downlink transmission with a hybrid beamforming structure. A user grouping algorithm is first proposed according to the channel correlations of the users. Whereafter, a joint hybrid beamforming and power allocation problem is formulated to maximize the achievable sum rate, subject to a minimum rate constraint for each user. To solve this non-convex problem with high-dimensional variables, we first obtain the solution of power allocation under arbi…
This paper presents LuMaMi28, a real-time 28 GHz massive multiple-input multiple-output (MIMO) testbed. In this testbed, the base station has 16 transceiver chains with a fully-digital beamforming architecture (with different pre-coding algorithms) and simultaneously supports multiple user equipments (UEs) with spatial multiplexing. The UEs are equipped with a beam-switchable antenna array for real-time antenna selection where the one with the highest channel magnitude, out of four pre-defined beams, is selected. For the beam-switchable antenna array, we consider two kinds of UE antennas, with…
This paper develops a novel methodology for designing analog beamforming codebooks for full-duplex millimeter wave (mmWave) transceivers, the first such codebooks to the best of our knowledge. Our design reduces the self-interference coupled by transmit-receive beam pairs and simultaneously delivers high beamforming gain over desired coverage regions, allowing mmWave full-duplex systems to support beam alignment while minimizing self-interference. To do so, our methodology allows some variability in beamforming gain to strategically shape beams that reject self-interference while still having …
The wide bandwidths offered at millimeter-wave (mmWave) frequencies have made them an attractive choice for future wireless communication systems. Recent works have presented beamforming strategies for enabling in-band full-duplex (FD) capability at mmWave even under the constraints of hybrid beamforming, extending the exciting possibilities of next-generation wireless. Existing mmWave FD designs, however, do not consider frequency-selective mmWave channels. Wideband communication at mmWave suggests that frequency-selectivity will likely be of concern since communication channels will be on th…
This paper summarizes an investigation around millimeter-wave (mmWave) multimode circular antenna array based beamformer capable of specially encoded data transmission in a wide coverage area. The circular antenna array is capable of an entire 360 deg. azimuth sector coverage where broadcast, uni-cast and multi-cast radio transmissions are possible. Orbital angular momentum (OAM) mode transmission along the elevation axis, i.e., perpendicular to the azimuth plane, can also be achieved. These two types of spatially encoded beamforming makes coverage in almost an entire hemisphere possible. The …
Millimeter-wave self-backhauled small cells are a key component of next-generation wireless networks. Their dense deployment will increase data rates, reduce latency, and enable efficient data transport between the access and backhaul networks, providing greater flexibility not previously possible with optical fiber. Despite their high potential, operating dense self-backhauled networks optimally is an open challenge, particularly for radio resource management (RRM). This paper presents, RadiOrchestra, a holistic RRM framework that models and optimizes beamforming, rate selection as well as us…
In this paper, we consider channel estimation for intelligent reflecting surface (IRS)-assisted millimeter wave (mmWave) systems, where an IRS is deployed to assist the data transmission from the base station (BS) to a user. It is shown that for the purpose of joint active and passive beamforming, the knowledge of a large-size cascade channel matrix needs to be acquired. To reduce the training overhead, the inherent sparsity in mmWave channels is exploited. By utilizing properties of Katri-Rao and Kronecker products, we find a sparse representation of the cascade channel and convert cascade ch…
This work develops LoneSTAR, a novel enabler of full-duplex millimeter wave (mmWave) communication systems through the design of analog beamforming codebooks. LoneSTAR codebooks deliver high beamforming gain and broad coverage while simultaneously reducing the self-interference coupled by transmit and receive beams at a full-duplex mmWave transceiver. Our design framework accomplishes this by tolerating some variability in transmit and receive beamforming gain to strategically shape beams that reject self-interference spatially while accounting for digitally-controlled analog beamforming netwo…
In recent years, there has been extensive research on millimeter-wave (mmWave) communication and on in-band full-duplex (FD) communication, but work on the combination of the two is relatively lacking. FD mmWave systems could offer increased spectral efficiency and decreased latency while also suggesting the redesign of existing mmWave applications. While FD technology has been well-explored for sub-6 GHz systems, the developed methods do not translate well to mmWave. This turns us to a method called beamforming cancellation (BFC), where the highly directional mmWave beams are steered to mitig…
A novel location-aware beamforming scheme for millimeter wave communication is proposed for line of sight (LOS) and low mobility scenarios, in which computer vision is introduced to derive the required position or spatial angular information from the image or video captured by camera(s) co-located with mmWave antenna array at base stations. A wireless coverage model is built to investigate the coverage performance and influence of positioning accuracy achieved by convolutional neural network (CNN) for image processing. In addition, videos could be intentionally blurred, or even low-resolution …
In this letter, we investigate the hybrid beamforming for millimeter wave massive multiple-input multiple-output (MIMO) system based on deep reinforcement learning (DRL). Imperfect channel state information (CSI) is assumed to be available at the base station (BS). To achieve high spectral efficiency with low time consumption, we propose a novel DRL-based method called PrecoderNet to design the digital precoder and analog combiner. The DRL agent takes the digital beamformer and analog combiner of the previous learning iteration as state, and these matrices of current learning iteration as acti…
Hybrid beamforming (HBF) design is a crucial stage in millimeter wave (mmWave) multi-user multi-input multi-output (MU-MIMO) systems. However, conventional HBF methods are still with high complexity and strongly rely on the quality of channel state information. We propose an extreme learning machine (ELM) framework to jointly optimize transmitting and receiving beamformers. Specifically, to provide accurate labels for training, we first propose an factional-programming and majorization-minimization based HBF method (FP-MM-HBF). Then, an ELM based HBF (ELM-HBF) framework is proposed to increase…
An intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) massive multiple input multiple output (MIMO) system with transmit antenna selection (TAS) using orthogonal space-time block codes (OSTBC) scheme is proposed in this paper. This system combines TAS and IRS with hybrid analog-digital beamforming (HBF) for 60 GHz mmWave communications in order to exploit the benefits of TAS, OSTBC, analog beamforming (ABF), and transmit digital precoding techniques. The proposed system, however, benefits from the transmit diversity gain of OSTBC scheme as well as from the signal-to-noise r…
Hybrid beamforming (HB) has emerged as a promising technology to support ultra high transmission capacity and with low complexity for Millimeter Wave (mmWave) multiple-input and multiple-output (MIMO) system. However, the design of digital and analog beamformer is a challenge task with non-convex optimization, especially for the multi-user scenario. Recently, the blooming of deep learning research provides a new vision for the signal processing of communication system. In this work, we propose a deep neural network based HB for the multi-User mmWave massive MIMO system, referred as DNHB. The H…
We consider the problem of spatial channel covariance matrix (CCM) estimation for intelligent reflecting surface (IRS)-assisted millimeter wave (mmWave) communication systems. Spatial CCM is essential for two-timescale beamforming in IRS-assisted systems; however, estimating the spatial CCM is challenging due to the passive nature of reflecting elements and the large size of the CCM resulting from massive reflecting elements of the IRS. In this paper, we propose a CCM estimation method by exploiting the low-rankness as well as the positive semi-definite (PSD) 3-level Toeplitz structure of the …
Beamforming technique realized by the multiple-input-multiple-output (MIMO) antenna arrays has been widely used to compensate for the severe path loss in the millimeter wave (mmWave) bands. In 5G NR system, the beam sweeping and beam refinement are employed to find out the best beam codeword aligned to the mobile. Due to the complicated handshaking and finite resolution of the codebook, today's 5G-based beam management strategy is ineffective in various scenarios in terms of the data rate, energy consumption, and also processing latency. An aim of this article is to introduce a new type of bea…
Unmanned aerial vehicles (UAVs) have found widespread commercial, civilian, and military applications. Wireless communication has always been one of the core technologies for UAV. However, the communication capacity is becoming a bottleneck for UAV to support more challenging application scenarios. The heavily-occupied sub-6 GHz frequency band is not sufficient to meet the ultra high-data-traffic requirements. The utilization of the millimeter-wave (mmWave) frequency bands is a promising direction for UAV communications, where large antenna arrays can be packed in a small area on the UAV to pe…
A fundamental challenge for millimeter wave (mmWave) communications lies in its sensitivity to the presence of blockages, which impact the connectivity of the communication links and ultimately the reliability of the entire network. In this paper, we analyze a reconfigurable intelligent surface (RIS)-aided mmWave communication system for enhancing the network reliability and connectivity in the presence of random blockages. To enhance the robustness of hybrid analog-digital beamforming in the presence of random blockages, we formulate a stochastic optimization problem based on the minimization…
There have been recent works on enabling in-band full-duplex operation using millimeter-wave (mmWave) transceivers. These works are based solely on creating sufficient isolation between a transceiver's transmitter and receiver via multiple-input multiple-output (MIMO) precoding and combining. In this work, we propose supplementing these beamforming strategies with analog self-interference cancellation (A-SIC). By leveraging A-SIC, a portion of the self-interference is cancelled without the need for beamforming, allowing for more optimal beamforming strategies to be used in serving users. We us…
We consider the problem of channel estimation and joint active and passive beamforming for reconfigurable intelligent surface (RIS) assisted millimeter wave (mmWave) multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) systems. We show that, with a well-designed frame-based training protocol, the received pilot signal can be organized into a low-rank third-order tensor that admits a canonical polyadic decomposition (CPD). Based on this observation, we propose two CPD-based methods for estimating the cascade channels associated with different subcarriers. The …
In time-division duplexing (TDD) millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems, the reciprocity mismatch severely degrades the performance of the hybrid beamforming (HBF). In this work, to mitigate the detrimental effect of the reciprocity mismatch, we investigate reciprocity calibration for the mmWave-HBF system with a fully-connected phase shifter network. To reduce the overhead and computational complexity of reciprocity calibration, we first decouple digital radio frequency (RF) chains and analog RF chains with beamforming design. Then, the entire calibrati…
Millimeter wave (mmWave) communications are evolving as a promising technology to meet the ever increasing data rate requirements. However, high directivity and severe path loss make it vulnerable to blockages, which could be frequent in indoor or urban environments. To address this issue, intelligent reflecting surfaces (IRSs) are introduced to provide additional adjustable reflected paths. Most prior works assume that elements of IRSs have an infinite phase resolution, which is difficult to be realized in practical systems. In this paper, IRSs with low-resolution phase shifters are considere…
