There have been recent works on enabling in-band full-duplex operation using millimeter-wave (mmWave) transceivers. These works are based solely on creating sufficient isolation between a transceiver's transmitter and receiver via multiple-input multiple-output (MIMO) precoding and combining. In this work, we propose supplementing these beamforming strategies with analog self-interference cancellation (A-SIC). By leveraging A-SIC, a portion of the self-interference is cancelled without the need for beamforming, allowing for more optimal beamforming strategies to be used in serving users. We use simulation to demonstrate that even with finite resolution A-SIC solutions, there are significant gains to be had in sum spectral efficiency. With a single bit of A-SIC resolution, improvements over a beamforming-only design are present. With 8 bits of A-SIC resolution, our design nearly approaches that of ideal full-duplex operation. To the best of our knowledge, this is the first mmWave full-duplex design that combines both beamforming and A-SIC to achieve simultaneous transmission and reception in-band.
This article provides an overview of research on full-duplex at the University of California, Riverside, in the past decade. This research was initially focused on self-interference (SI) cancellation, then moved to applications of full-duplex to improve network spectral efficiency, and in recent years advanced to discover full-duplex's potentials for wireless network security. The research on SI cancellation has resulted in both hardware-based SI cancellation results and some advanced theoretical architectures which show promises but are yet to be tested via advanced hardware implementations. …
In-band full-duplex systems are able to transmit and receive information simultaneously on the same frequency band. Due to the strong self-interference caused by the transmitter to its own receiver, the use of non-linear digital self-interference cancellation is essential. In this work, we present a hardware architecture for a neural network based non-linear self-interference canceller and we compare it with our own hardware implementation of a conventional polynomial based canceller. We show that, for the same cancellation performance, the neural network canceller has a significantly higher t…
In-band full-duplex systems promise to further increase the throughput of wireless systems, by simultaneously transmitting and receiving on the same frequency band. However, concurrent transmission generates a strong self-interference signal at the receiver, which requires the use of cancellation techniques. A wide range of techniques for analog and digital self-interference cancellation have already been presented in the literature. However, their evaluation focuses on cases where the underlying physical parameters of the full-duplex system do not vary significantly. In this paper, we focus o…
In this paper, we focus on reduced complexity full duplex Multiple-Input Multiple-Output (MIMO) systems and present a joint design of digital transmit and receive beamforming with Analog and Digital (A/D) self-interference cancellation. We capitalize on a recently proposed multi-tap analog canceller architecture, whose number of taps does not scale with the number of transceiver antennas, and consider practical transmitter impairments for the full duplex operation. Particularly, transmitter IQ imbalance and nonlinear power amplification are assumed via relevant realistic models. Aiming at supp…
Reconfigurable intelligent surfaces (RIS) are a key enabler of various new applications in 6G smart radio environments. By utilizing an RIS prototype system, this paper aims to enhance self-interference (SI) cancellation for in-band full-duplex (FD) communication systems. SI suppression is a crucial requirement for FD communication as the SI severely limits the performance of a node by shadowing the received signal from a distant node with its own transmit signal. To this end, we propose to assist SI cancellation by exploiting an RIS to form a suitable cancellation signal in the analog domain.…
Single-antenna full-duplex communication technology has the potential to substantially increase spectral efficiency. However, limited propagation domain cancellation of single-antenna system results in a higher impact of receiver chain nonlinearities on the residual self-interference (SI) signal. In this paper, we offer a comprehensive SI model for single-antenna full-duplex systems based on direct-conversion transceiver structure considering nonlinearities of all the transceiver radio frequency (RF) components, in-phase/quadrature (IQ) imbalances, phase noise effect, and receiver noise figure…
For future wireless communication systems, full duplex is seen as a possible solution to the ever present spectrum shortage. The key aspect to enable In-Band Full Duplex (IBFD) is sufficient cancellation of the unavoidable Self-Interference (SI). In this work we evaluate the performance of a low complexity IBFD transceiver, including the required analog and digital interference cancellation techniques. The Radio Frequency Self- Interference Canceler (RFSIC) is based on the isolation of a circulator in combination with a vector modulator regenerating the interference signal, to destructively co…
In-band full-duplex systems allow for more efficient use of temporal and spectral resources by transmitting and receiving information at the same time and on the same frequency. However, this creates a strong self-interference signal at the receiver, making the use of self-interference cancellation critical. Recently, neural networks have been used to perform digital self-interference with lower computational complexity compared to a traditional polynomial model. In this paper, we examine the use of advanced neural networks, such as recurrent and complex-valued neural networks, and we perform …
In recent years, there has been extensive research on millimeter-wave (mmWave) communication and on in-band full-duplex (FD) communication, but work on the combination of the two is relatively lacking. FD mmWave systems could offer increased spectral efficiency and decreased latency while also suggesting the redesign of existing mmWave applications. While FD technology has been well-explored for sub-6 GHz systems, the developed methods do not translate well to mmWave. This turns us to a method called beamforming cancellation (BFC), where the highly directional mmWave beams are steered to mitig…
We consider a bidirectional in-band full-duplex (FD) multiple-input multiple-output (MIMO) system subject to imperfect channel state information (CSI), hardware distortion, and limited analog cancellation capability as well as the self-interference (SI) power requirement at the receiver analog domain so as to avoid the saturation of low noise amplifier (LNA). A novel minimum mean square error (MMSE)-based joint design of digital precoder and combiner for SI cancellation is offered, which combines the well-known gradient projection method and non-monotonicity considered in recent machine-learni…
Equipping millimeter wave (mmWave) systems with full-duplex capability would accelerate and transform next-generation wireless applications and forge a path for new ones. Full-duplex mmWave transceivers could capitalize on the already attractive features of mmWave communication by supplying spectral efficiency gains and latency improvements while also affording future networks with deployment solutions in the form of interference management and wireless backhaul. Foreseeable challenges and obstacles in making mmWave full-duplex a reality are presented in this article along with noteworthy unkn…
One of the main obstacles in full-duplex radios is analog-to-digital converter (ADC) saturation on a receiver due to the strong self-interference (SI). To solve this issue, researchers have proposed two different types of analog self-interference cancellation (SIC) methods -- i) passive suppression and ii) regeneration-and-subtraction of SI. For the latter case, the tunable RF component, such as a multi-tap circuit, reproduces and subtracts the SI. The resolutions of such RF components constitute the key factor of the analog SIC. Indeed, they are directly related to how well the SI is imitated…
Millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems have been considered as one of the primary candidates for the fifth generation (5G) and beyond 5G wireless communication networks to satisfy the ever-increasing capacity demands. Full-duplex technology can further enhance the advantages of mmWave massive MIMO systems. However, strong self-interference (SI) is the major limiting factor in full-duplex technology. Hence, this paper proposes a novel angular-based joint hybrid precoding/combining (AB-JHPC) technique for the full-duplex mmWave massive-MIMO systems. Our pr…
Full-duplex (FD) systems have the capability to transmit and receive at the same time in the same frequency band. FD systems can reduce congestion and latency and improve coverage and spectral efficiency. As a relay, they can increase range and decrease outages. Full-duplex (FD) wireless systems have been emerging as a practical solution to provide high bandwidth, low latency, and big data processing in millimeter wave and Terahertz systems to support cellular networks, autonomous driving, platooning, advanced driving assistance and other systems. However, FD systems suffer from loopback self-…
The wide bandwidths offered at millimeter-wave (mmWave) frequencies have made them an attractive choice for future wireless communication systems. Recent works have presented beamforming strategies for enabling in-band full-duplex (FD) capability at mmWave even under the constraints of hybrid beamforming, extending the exciting possibilities of next-generation wireless. Existing mmWave FD designs, however, do not consider frequency-selective mmWave channels. Wideband communication at mmWave suggests that frequency-selectivity will likely be of concern since communication channels will be on th…
A photonic approach for radio-frequency (RF) self-interference cancellation (SIC) incorporated in an in-band full-duplex radio-over-fiber system is proposed. A dual-polarization binary phase-shift keying modulator is used for dual-polarization multiplexing at the central office (CO). A local oscillator signal and an intermediate-frequency signal carrying the downlink data are single-sideband modulated on the two polarization directions of the modulator, respectively. The optical signal is then transmitted to the remote unit, where the optical signals in the two polarization directions are spli…
A digitally-assisted photonic analog domain self-interference cancellation (SIC) and frequency downconversion method is proposed for in-band full-duplex multiple-input multiple-output (MIMO) systems using the least square (LS) algorithm with adaptive order. The SIC and frequency downconversion are achieved in the optical domain via a dual-parallel Mach-Zehnder modulator (DP-MZM), while the downconverted signal is processed by the LS algorithm with adaptive order that is used to track the response of the multipath self-interference (SI) channel and reconstruct the reference signal for SIC. The …
Full-duplex systems require very strong self-interference cancellation in order to operate correctly and a significant part of the self-interference signal is due to non-linear effects created by various transceiver impairments. As such, linear cancellation alone is usually not sufficient and sophisticated non-linear cancellation algorithms have been proposed in the literature. In this work, we investigate the use of a neural network as an alternative to the traditional non-linear cancellation method that is based on polynomial basis functions. Measurement results from a full-duplex testbed de…
This paper addresses the performance of a full-duplex (FD) generalized frequency division multiplexing (GFDM) transceiver in the presence of radio frequency (RF) impairments including phase noise, carrier frequency offset (CFO) and in-phase (I) and quadrature (Q) imbalance. We study analog and digital self-interference (SI) cancellation and develop a complementary SI suppression method. Closed-form solutions for the residual SI power and the desired signal power and signal-to-interference ratio (SIR) are provided. Simulation results show that the RF impairments degrade SI cancellation and FD G…
Photonics-assisted analog wideband self-interference cancellation for in-band full-duplex MIMO systems with adaptive digital amplitude and delay pre-matching
Self-interference (SI) is the main obstacle to full-duplex radios. To overcome the SI, researchers have proposed several analog and digital domain self-interference cancellation (SIC) techniques. How well the digital cancellation works depends on the results of analog cancellation. Therefore, to analyze overall SIC performance, one should do so in an integrated manner. In this paper, we build a simulator that can analyze the performance of analog and digital SIC techniques. Through this simulator, we can analyze the overall SIC performance within various system parameters such as the resolutio…
In this letter, we propose a modified version of Fast Independent Component Analysis (FICA) algorithm to solve the self-interference cancellation (SIC) problem in In-band Full Duplex (IBFD) communication systems. The complex mixing problem is mathematically formulated to suit the real-valued blind source separation (BSS) algorithms. In addition, we propose a method to estimate the ambiguity factors associated with ICA lumped together with the channels and residual separation error. Experiments were performed on an FD platform where FICA-based BSS was applied for SIC in the frequency domain. Ex…
Although the hardware complexity of the analog self-interference canceller in full duplex Multiple Input Multiple Output (MIMO) designs does not necessarily scale with the number of transceiver antennas, exploiting the benefits of analog cancellation in massive MIMO systems with hundreds of antenna elements is still quite impractical. Hybrid Analog and Digital (A/D) beamforming architectures have been lately considered as a candidate technology for realizing massive MIMO transceivers with very large number of antenna elements, but with much fewer numbers of Radio Frequency (RF) chains. In this…
Memorial University（纪念大学）；Benha University（本哈大学）；Huawei Technologies Canada Co., Ltd.（华为技术加拿大有限公司）
Self-interference (SI) is considered as a main challenge in full-duplex (FD) systems. Therefore, efficient SI cancelers are required for the influential deployment of FD systems in beyond fifth-generation wireless networks. Existing methods for SI cancellation have mostly considered the polynomial representation of the SI signal at the receiver. These methods are shown to operate well in practice while requiring high computational complexity. Alternatively, neural networks (NNs) are envisioned as promising candidates for modeling the SI signal with reduced computational complexity. Consequentl…
This letter presents a device-to-device (D2D) enabling cellular full-duplex (FD) cooperative protocol using non-orthogonal multiple access (NOMA), where an FD relay assists in relaying NOMA far user's signal and transmits a D2D receiver's signal simultaneously. The ergodic capacity, outage probability, and diversity order of the proposed protocol are theoretically investigated under the realistic assumption of imperfect self and known interference cancellation. The Outcome of the investigation demonstrates the performance gain of the suggested protocol over conventional FD cooperative NOMA sys…
Wireless communication systems can be enhanced at the link level, in medium access, and at the network level when transceivers are equipped with full-duplex capability: the transformative ability to simultaneously transmit and receive over the same frequency spectrum. Effective methods to cancel self-interference are required to facilitate full-duplex operation, which we overview herein in the context of traditional radios, along with those in next-generation wireless networks. We highlight advances in self-interference cancellation that leverage machine learning, and we summarize key consider…
In this paper, we propose a wideband Full Duplex (FD) Multiple-Input Multiple-Output (MIMO) communication system comprising of an FD MIMO node simultaneously communicating with two multi-antenna UpLink (UL) and DownLink (DL) nodes utilizing the same time and frequency resources. To suppress the strong Self-Interference (SI) signal due to simultaneous transmission and reception in FD MIMO systems, we propose a joint design of Analog and Digital (A/D) cancellation as well as transmit and receive beamforming capitalizing on baseband Orthogonal Frequency-Division Multiplexing (OFDM) signal modelin…
In this letter, we study the reconfigurable intelligent surfaces (RIS) aided full-duplex (FD) communication system. By jointly designing the active beamforming of two multi-antenna sources and passive beamforming of RIS, we aim to maximize the energy efficiency of the system, where extra self-interference cancellation power consumption in FD system is also considered. We divide the optimization problem into active and passive beamforming design subproblems, and adopt the alternative optimization framework to solve them iteratively. Dinkelbach's method is used to tackle the fractional objective…
The full-duplex (FD) communication can achieve higher spectrum efficiency than conventional half-duplex (HD) communication; however, self-interference (SI) is the key hurdle. This paper is the first work to propose the intelligent Omni surface (IOS)-assisted FD multi-input single-output (MISO) FD communication systems to mitigate SI, which solves the frequency-selectivity issue. In particular, two types of IOS are proposed, energy splitting (ES)-IOS and mode switching (MS)-IOS. We aim to maximize data rate and minimize SI power by optimizing the beamforming vectors, amplitudes and phase shifts…
Transceivers operating in frequency division duplex experience a transmitter leakage (TxL) signal into the receiver due to the limited duplexer stop-band isolation. This TxL signal in combination with the second-order nonlinearity of the receive mixer may lead to a baseband (BB) second-order intermodulation distortion (IMD2) with twice the transmit signal bandwidth. In direct conversion receivers, this nonlinear IMD2 interference may cause a severe signal-to-interference-plus-noise ratio degradation of the wanted receive signal. This contribution presents a nonlinear Wiener model recursive lea…
In this paper, we study Full Duplex (FD) Multiple-Input Multiple-Output (MIMO) radios for simultaneous data communication and control information exchange. Capitalizing on a recently proposed FD MIMO architecture combining digital transmit and receive beamforming with reduced complexity multi-tap analog Self-Interference (SI) cancellation, we propose a novel transmission scheme exploiting channel reciprocity for joint downlink beamformed information data communication and uplink channel estimation through training data transmission. We adopt a general model for pilot-assisted channel estimatio…
This work develops LoneSTAR, a novel enabler of full-duplex millimeter wave (mmWave) communication systems through the design of analog beamforming codebooks. LoneSTAR codebooks deliver high beamforming gain and broad coverage while simultaneously reducing the self-interference coupled by transmit and receive beams at a full-duplex mmWave transceiver. Our design framework accomplishes this by tolerating some variability in transmit and receive beamforming gain to strategically shape beams that reject self-interference spatially while accounting for digitally-controlled analog beamforming netwo…
The evolution of wireless systems has led to a continuous increase in the demand for radio frequency spectrum. To address this issue, a technology that has received a lot of attention is In-Band Full-Duplex (IBFD). The interest in IBFD systems stems from its capability to simultaneously transmit and receive data in the same frequency. Cancelling the self interference (SI) from the transmitter to the collocated receiver plays a pivotal role in the performance of the system. There are two types of SI cancellation (SIC) approaches, passive and active. In this research, the focus is on active canc…
Interference cancellation is the main driving technology in enhancing the transmission rates over telephone lines above 100 Mbps. Still, crosstalk interference in multi-pair digital subscriber line (DSL) systems at higher frequencies has not been dealt with sufficiently. The upcoming G.(mg) fast DSL system envisions the use of extremely high bandwidth and full-duplex transmissions generating significantly higher crosstalk and self-interference signals. More powerful interference cancellation techniques are required to enable multi-gigabit per second data rate transmission over copper lines. In…
Radio frequency transceivers operating in in-band full-duplex or frequency-division duplex mode experience strong transmitter leakage. Combined with receiver nonlinearities, this causes intermodulation products in the baseband, possibly with higher power than the desired receive signal. In order to restore the receiver signal-to-noise ratio in such scenarios, we propose two novel digital self-interference cancellation approaches based on spline interpolation. Both employ a Wiener structure, thereby matching the baseband model of the intermodulation effect. Unlike most state-of-the-art spline-b…
This paper investigates the downlink transmission of reconfigurable intelligent surface (RIS)-aided cooperative non-orthogonal-multiple-access (C-NOMA), where both half-duplex (HD) and full-duplex (FD) relaying modes are considered. The system model consists of one base station (BS), two users and one RIS. The goal is to minimize the total transmit power at both the BS and at the user-cooperating relay for each relaying mode by jointly optimizing the power allocation coefficients at the BS, the transmit power coefficient at the relay user, and the passive beamforming at the RIS, subject to pow…
In order to support experimentation with full-duplex (FD) wireless, we recently integrated an open-access FD transceiver in the ORBIT testbed. In this report, we present the design and implementation of the FD transceiver and interfaces, and provide examples and guidelines for experimentation. In particular, an ORBIT node with a National Instruments (NI)/Ettus Research Universal Software Radio Peripheral (USRP) N210 software-defined radio (SDR) was equipped with the Columbia FlexICoN Gen-1 customized RF self-interference (SI) canceller box. The RF canceller box includes an RF SI canceller that…
