Full Duplex Hybrid A/D Beamforming with Reduced Complexity Multi-Tap Analog Cancellation
George C. Alexandropoulos, Md Atiqul Islam, Besma Smida
备注：
5 pages, 2 figures, To appear in the Proceedings of the IEEE International Workshop on Signal Processing Advances in Wireless Communications (SPAWC), 26-29 May 2020, Atlanta, USA
Although the hardware complexity of the analog self-interference canceller in full duplex Multiple Input Multiple Output (MIMO) designs does not necessarily scale with the number of transceiver antennas, exploiting the benefits of analog cancellation in massive MIMO systems with hundreds of antenna elements is still quite impractical. Hybrid Analog and Digital (A/D) beamforming architectures have been lately considered as a candidate technology for realizing massive MIMO transceivers with very large number of antenna elements, but with much fewer numbers of Radio Frequency (RF) chains. In this paper, we present a novel architecture for full duplex hybrid A/D beamforming transceivers including multi-tap analog cancellation with reduced number of taps and simple multiplexers for efficient signal routing among the transceiver RF chains. Capitalizing on the proposed transceiver architecture, we present a joint design of analog cancellation and A/D beamforming with the objective to maximize the achievable full duplex rate performance. Representative millimeter wave simulation results demonstrate the effectiveness of the proposed architecture and algorithmic framework for enabling simultaneous uplink and downlink communications with reduced complexity analog self-interference cancellation.
We study the beamforming optimization for an intelligent reflecting surface (IRS)-aided full-duplex (FD) communication system in this letter. Specifically, we maximize the sum rate of bi-directional transmissions by jointly optimizing the transmit beamforming and the beamforming of the IRS reflection. A fast converging alternating algorithm is developed to tackle this problem. In each iteration of the proposed algorithm, the solutions to the transmit beamforming and the IRS reflect beamforming are obtained in a semi-closed form and a closed form, respectively. Compared to an existing method ba…
Full Duplex (FD) communication can revolutionize wireless communications as it avoids using independent channels for bi-directional communications. This work generalizes the point-to-point FD communication in millimeter wave (mmWave) band consisting of K-pairs of massive MIMO FD nodes operating simultaneously. We present a novel joint hybrid beamforming (HYBF) and combining scheme for weighted sum-rate (WSR) maximization to enable the coexistence of massive MIMO FD links cost-efficiently. The proposed algorithm relies on alternative optimization based on the minorization-maximization method. M…
In this paper, we propose a full-duplex relay (FDR) based on a zero-forcing beamforming (ZFBF) for a multiuser MIMO relay system. The ZFBF is employed at the base station to suppress both the self-interference of the relay and the multiuser interference at the same time. Numerical results show that the proposed FDR can enhance the sum rate performance as compared to the half-duplex relay (HDR), if sufficient isolation between the transmit and receive antennas is ensured at the relay.
Beamforming design has been widely investigated for integrated sensing and communication (ISAC) systems with full-duplex (FD) sensing and half-duplex (HD) communication. To achieve higher spectral efficiency, in this paper, we extend existing ISAC beamforming design by considering the FD capability for both radar and communication. Specifically, we consider an ISAC system, where the base station (BS) performs target detection and communicates with multiple downlink users and uplink users reusing the same time and frequency resources. We jointly optimize the downlink dual-functional transmit si…
In this paper, a novel full-duplex non-coherent (FD-NC) transmission scheme is developed for massive multiple-input multiple-output (mMIMO) systems using analog beamforming (ABF). We propose to use a structured Grassmannian constellation for the non-coherent communications that does not require channel estimation. Then, we design the transmit and receive ABF via the slow time-varying angle-of-departure (AoD) and angle-of-arrival (AoA) information, respectively. The ABF design targets maximizing the intended signal power while suppressing the strong self-interference (SI) occurred in the FD tra…
In this paper, full-duplex radios are used to continuously update the channel state information at the transmitter, which is required to compute the downlink precoding matrix in MIMO broadcast channels. The full-duplex operation allows leveraging channel reciprocity for open-loop uplink training to estimate the downlink channels. However, the uplink transmission of training creates interference at the downlink receiving mobile nodes. We characterize the optimal training resource allocation and its associated spectral efficiency, in the proposed open-loop training based full-duplex system. We a…
Incorporating full duplex operation in Multiple Input Multiple Output (MIMO) systems provides the potential of boosting throughput performance. However, the hardware complexity of the analog self-interference canceller scales with the number of transmit and receive antennas, thus exploiting the benefits of analog cancellation becomes impractical for full duplex MIMO transceivers. In this paper, we present a novel architecture for the analog canceller comprising of reduced number of taps (tap refers to a line of fixed delay and variable phase shifter and attenuator) and simple multiplexers for …
We identify phase noise as a bottleneck for the performance of digital self-interference cancellers that utilize a single auxiliary receiver---single-tap digital cancellers---and operate in multipath propagation environments. Our analysis demonstrates that the degradation due to phase noise is caused by a mismatch between the analog delay of the auxiliary receiver and the different delays of the multipath components of the self-interference signal. We propose a novel multi-tap digital self-interference canceller architecture that is based on multiple auxiliary receivers and a customized Normal…
In this paper we explore the use of full-duplex radio to improve the spectrum efficiency in a two-way relay channel where two sources exchange information through an multi-antenna relay, and all nodes work in the full-duplex mode. The full-duplex operation can reduce the overall communication to only one phase but suffers from the self-interference. Instead of purely suppressing the self-interference, we aim to maximize the end-to-end performance by jointly optimizing the beamforming matrix at the relay which uses the amplify-and-forward protocol as well as the power control at the sources. To…
A full-duplex two-way relay channel with multiple antennas is considered. For this three-node network, the beamforming design needs to suppress self-interference. While a traditional way is to apply zero-forcing for self-interference mitigation, it may harm the desired signals. In this paper, a design which reserves a fraction of self-interference is proposed by solving a quality-of-service constrained beamforming design problem. Since the problem is challenging due to the loop self-interference, a convergence-guaranteed alternating optimization algorithm is proposed to jointly design the rela…
In this paper, we deal with the performance analysis of full-duplex relaying in decode-&-forward cooperative networks with multiple-antenna terminals. More specifically, by analyzing the end-to-end statistics, we derive the accurate closed-form expressions of the end-to-end outage probability for both transmit and receive ZFBF scheme over Rayleigh fading environments. Some selected results show some interesting observations useful for system designers. Specifically, we observe that the outage performance can be improved by adopting the joint ZF-based precoding with different antenna configurat…
In this paper, we studied the joint sparse beamforming and power control for network-assisted full duplex (NAFD) in large-scale distributed antenna system (L-DAS), where the remote antenna units either be operating in half-duplex mode or full-duplex mode are all connected to the central processing unit (CPU) via high-speed backhaul links. With joint processing at CPU, NAFD could achieve truly flexible duplex, including flexible half-duplex and full-duplex. Cross-link interference and the finite-capacity backhaul are the main problems of NAFD in L-DAS. To solve these problems, we aim to maximiz…
We consider the full-duplex (FD) two-way amplify-and-forward relay system with imperfect cancelation of loopback self-interference (SI) and investigate joint design of relay and receive beamforming for minimizing the mean square error under a relay transmit power constraint. Due to loopback channel estimation error and limitation of analog-to-digital converter, the loopback SI cannot be completely canceled. Multiple antennas at the relay can help loopback SI suppression but beamforming is required to balance between the residual SI suppression and the desired signal transmission. Moreover, the…
In this paper, we investigate the problem of two-way relay beamforming optimization to maximize the achievable sum-rate of a simultaneous wireless information and power transfer (SWIPT) system with a full-duplex (FD) multiple-input multiple-output (MIMO) amplify-and-forward (AF) relay. In particular, we address the optimal joint design of the receiver power splitting (PS) ratio and the beamforming matrix at the relay node given the channel state information (CSI). Our contribution is an iterative algorithm based on difference of convex (DC) programming and one-dimensional searching to achieve …
Multiple transmitting antennas can considerably increase the downlink spectral efficiency by beamforming to multiple users at the same time. However, multiuser beamforming requires channel state information (CSI) at the transmitter, which leads to training overhead and reduces overall achievable spectral efficiency. In this paper, we propose and analyze a sequential beamforming strategy that utilizes full-duplex base station to implement downlink data transmission concurrently with CSI acquisition via in-band closed or open loop training. Our results demonstrate that full-duplex capability can…
This paper studies intelligent reflecting surface (IRS)-aided full-duplex (FD) wireless-powered communication network (WPCN), where a hybrid access point (HAP) broadcasts energy signals to multiple devices for their energy harvesting in the downlink (DL) and meanwhile receives information signals in the uplink (UL) with the help of IRS. Particularly, we propose three types of IRS beamforming configurations to strike a balance between the system performance and signaling overhead as well as implementation complexity. We first propose the fully dynamic IRS beamforming, where the IRS phase-shift …
In this paper, we present and study a digital-controlled method, called SoftNull, to enable full-duplex in many-antenna systems. Unlike most designs that rely on analog cancelers to suppress self-interference, SoftNull relies on digital transmit beamforming to reduce self-interference. SoftNull does not attempt to perfectly null self-interference, but instead seeks to reduce self-interference sufficiently to prevent swamping the receiver's dynamic range. Residual self-interference is then cancelled digitally by the receiver. We evaluate the performance of SoftNull using measurements from a 72-…
This letter considers the secure communication in a reconfigurable intelligent surface (RIS) aided full duplex (FD) system. An FD base station (BS) serves an uplink (UL) user and a downlink (DL) user simultaneously over the same time-frequency dimension assisted by a RIS in the presence of an eavesdropper. In addition, the artificial noise (AN) is also applied to interfere the eavesdropper's channel. We aim to maximize the sum secrecy rate of UL and DL users by jointly optimizing the transmit beamforming, receive beamforming and AN covariance matrix at the BS, and passive beamforming at the RI…
We model the self-interference in a multiple input single output (MISO) full-duplex two-way channel and evaluate the achievable rate region. We formulate the boundary of the achievable rate region termed as the Pareto boundary by a family of coupled, non-convex optimization problems. Our main contribution is decoupling and reformulating the original non-convex optimization problems to a family of convex semidefinite programming problems. For a MISO full-duplex two-way channel, we prove that beamforming is an optimal transmission strategy which can achieve any point on the Pareto boundary. Furt…
Millimeter wave (mmWave) full-duplex (FD) is a promising technique for improving capacity by maximizing the utilization of both time and the rich mmWave frequency resources. Still, it has restrictions due to FD self-interference (SI) and mmWave's limited coverage. Therefore, this study dives into FD mmWave MIMO with the assistance of reconfigurable intelligent surfaces (RIS) for capacity improvement. First, we demonstrate the angular-domain reciprocity of FD antenna arrays under the far-field planar wavefront assumption. Accordingly, a strategy for joint downlink-uplink (DL-UL) channel estimat…
We derive the optimal signaling for a multiple input multiple output (MIMO) full-duplex two-way channel under the imperfect transmit front-end chain. We characterize the two-way rates of the channel by using a game-theoretical approach, where we focus on the Pareto boundary of the achievable rate region and Nash equilibia (NE). For a MISO full-duplex two-way channel, we prove that beamforming is an optimal transmission strategy which can achieve any point on the Pareto boundary. Furthermore, we present a closed-form expression for the optimal beamforming weights. In our numerical examples we q…
This paper investigates the passive beamforming and deployment design for an intelligent reflecting surface (IRS) aided full-duplex (FD) wireless system, where an FD access point (AP) communicates with an uplink (UL) user and a downlink (DL) user simultaneously over the same time-frequency dimension with the help of IRS. Under this setup, we consider three deployment cases: 1) two distributed IRSs placed near the UL user and DL user, respectively; 2) one centralized IRS placed near the DL user; 3) one centralized IRS placed near the UL user. In each case, we aim to minimize the weighted sum tr…
We solve a sum rate maximization problem of full-duplex (FD) multiuser multiple-input multiple-output (MU-MIMO) systems. Since additional self-interference (SI) in the uplink channel and co-channel interference (CCI) in the downlink channel are coupled in FD communication, the downlink and uplink multiuser beamforming vectors are required to be jointly designed. However, the joint optimization problem is non-convex and hard to solve due to the coupled effect. To properly address the coupled design issue, we reformulate the problem into an equivalent uplink channel problem, using the uplink and…
Full Duplex (FD) radio has emerged as a promising solution to increase the data rates by up to a factor of two via simultaneous transmission and reception in the same frequency band. This paper studies a novel hybrid beamforming (HYBF) design to maximize the weighted sum-rate (WSR) in a single-cell millimeter wave (mmWave) massive multiple-input-multiple-output (mMIMO) FD system. Motivated by practical considerations, we assume that the multi-antenna users and hybrid FD base station (BS) suffer from the limited dynamic range (LDR) noise due to non-ideal hardware and an impairment aware HYBF ap…
Integrated Sensing and Communication (ISAC) has attracted substantial attraction in recent years for spectral efficiency improvement, enabling hardware and spectrum sharing for simultaneous sensing and signaling operations. In-band Full Duplex (FD) is being considered as a key enabling technology for ISAC applications due to its simultaneous transmission and reception capability. In this paper, we present an FD-based ISAC system operating at millimeter Wave (mmWave) frequencies, where a massive Multiple-Input Multiple-Output (MIMO) Base Station (BS) node employing hybrid Analog and Digital (A/…
Security is a critical issue in full duplex (FD) communication systems due to the broadcast nature of wireless channels. In this paper, joint design of information and artificial noise beamforming vectors is proposed for the FD simultaneous wireless information and power transferring (FD-SWIPT) systems with loopback self-interference cancellation. To guarantee high security and energy harvesting performance of the FD-SWIPT system, the proposed design is formulated as a secrecy rate maximization problem under energy transfer rate constraints. Although the secrecy rate maximization problem is no…
This paper studies the joint optimization problem of two-way relay beamforming, the receiver power splitting (PS) ratio as well as the transmit power at the sources to maximize the achievable sum-rate of a simultaneous wireless information and power transfer (SWIPT) system with a full-duplex (FD) multiple-input multiple-output (MIMO) amplify and forward (AF) relay, assuming perfect channel state information (CSI). In particular, our contribution is an iterative algorithm based on the difference of convex programming (DC) and one dimensional searching to achieve the joint solution. Simulation r…
We propose techniques for optimizing transmit beamforming in a full-duplex multiple-input-multiple-output (MIMO) wireless-powered communication system, which consists of two phases. In the first phase, the wireless-powered mobile station (MS) harvests energy using signals from the base station (BS), whereas in the second phase, both MS and BS communicate to each other in a full-duplex mode. When complete instantaneous channel state information (CSI) is available, the BS beamformer and the time-splitting (TS) parameter of energy harvesting are jointly optimized in order to obtain the BS-MS rate…
Consider a two-way communication scenario where two single-antenna nodes, operating under full-duplex mode, exchange information to one another through the aid of a (full-duplex) multi-antenna relay, and there is another single-antenna node who intends to eavesdrop. The relay employs artificial noise (AN) to interfere the eavesdropper's channel, and amplify-forward (AF) Alamouti-based rank-two beamforming to establish the two-way communication links of the legitimate nodes. Our problem is to optimize the rank-two beamformer and AN covariance for sum secrecy rate maximization (SSRM). This SSRM …
In this paper, we consider a non-orthogonal multiple access cognitive radio network, where a full-duplex multi-antenna relay assists transmission from a base station (BS) to a cognitive far user, whereas, at the same time, the BS transmits to a cognitive near user. Our objective is to enlarge the far-near user rate region by maximizing the rate of the near user under a constraint that the rate of the far user is above a certain threshold. To this end, a non-convex joint optimization problem of relay beamforming and the transmit powers at the BS and cognitive relay is solved as a semi-definite …
Physical layer security is a key issue in the full duplex (FD) communication systems due to the broadcast nature of wireless channels. In this paper, the joint design of information and artificial noise beamforming vectors is proposed for the FD simultaneous wireless information and power transferring (FD-SWIPT) systems. To guarantee high security and energy harvesting performance of the FD-SWIPT system, the proposed design is formulated as a sum information transmission rate (SITR) maximization problem under information-leakage and energy constraints. In addition, we consider the fairness iss…
In this paper, we investigate a reconfigurable intelligent surface (RIS)-aided multiuser full-duplex secure communication system with hardware impairments at transceivers and RIS, where multiple eavesdroppers overhear the two-way transmitted signals simultaneously, and an RIS is applied to enhance the secrecy performance. Aiming at maximizing the sum secrecy rate (SSR), a joint optimization problem of the transmit beamforming at the base station (BS) and the reflecting beamforming at the RIS is formulated under the transmit power constraint of the BS and the unit modulus constraint of the phas…
Reconfigurable intelligent surfaces (RIS) have drawn considerable attention recently due to their controllable scattering elements that are able to direct electromagnetic waves into desirable directions. Although RISs share some similarities with relays, the two have fundamental differences impacting their performance. To harness the benefits of both relaying and RISs, a multi-user communication system is proposed in this paper wherein a relay and an RIS cooperate to improve performance in terms of energy efficiency. Using singular value decomposition (SVD), semidefinite programming (SDP), and…
In this paper, we propose a joint transceiver beamforming design to simultaneously mitigate self-interference (SI) and partial inter-node interference for full-duplex multiple-input and multiple-output ad-hoc network, and then derive the transmission capacity upper bound (TC-UB) for the corresponding network. Condition on a specified transceiver antenna's configuration, we allow the SI effect to be cancelled at transmitter side, and offer an additional degree-of-freedom at receiver side for more inter-node interference cancellation. In addition, due to the proposed beamforming design and imper…
In this paper, we investigate the physical layer security of a full-duplex base station (BS) aided system in the worst case, where an uplink transmitter (UT) and a downlink receiver (DR) are both equipped with a single antenna, while a powerful eavesdropper is equipped with multiple antennas. For securing the confidentiality of signals transmitted from the BS and UT, an artificial noise (AN) aided secrecy beamforming scheme is proposed, which is robust to the realistic imperfect state information of both the eavesdropping channel and the residual self-interference channel. Our objective functi…
This paper investigates a multiuser multiple-input single-output (MISO) full-duplex (FD) system for simultaneous wireless information and power transfer (SWIPT), in which a multi-antenna base station (BS) simultaneously sends wirelessly information and power to a set of single-antenna mobile stations (MSs) using power splitters (PSs) in the downlink and receives information in the uplink in FD mode. In particular, we address the joint design of the receive PS ratio and the transmit power at the MSs, and the beamforming matrix at the BS under signal-to-interference-plus-noise ratio (SINR) and t…
In this paper, we present a novel scenario for directional modulation (DM) networks with a full-duplex (FD) malicious attacker (Mallory), where Mallory can eavesdrop the confidential message from Alice to Bob and simultaneously interfere Bob by sending a jamming signal. Considering that the jamming plus noise at Bob is colored, an enhanced receive beamforming (RBF), whitening-filter-based maximum ratio combining (MRC) (WFMRC), is proposed. Subsequently, two RBFs of maximizing the secrecy rate (Max-SR) and minimum mean square error (MMSE) are presented to show the same performance as WFMRC. To …
This paper considers a cloud radio access network (C-RAN) where spatially distributed remote radio heads (RRHs) communicate with a full-duplex user. In order to reflect a realistic scenario, the uplink (UL) and downlink (DL) RRHs are assumed to be equipped with multiple antennas and distributed according to a Poisson point process. We consider all participate and nearest RRH association schemes with distributed beamforming in the form of maximum ratio combining/maximal ratio transmission (MRC/MRT) and zero-forcing/MRT(ZF/MRT) processing. We derive analytical expressions useful to compare the a…
Incorporating full duplex operation in Multiple Input Multiple Output (MIMO) systems provides the potential of boosting throughput performance. However, the hardware complexity of the analog self-interference canceller in emerging full duplex MIMO designs mostly scales with the number of transmit and receive antennas, thus exploiting the benefits of analog cancellation becomes impractical for full duplex MIMO transceivers, even for moderate number of antennas. In this paper, we present two novel architectures for the analog canceller comprising of reduced number of cancellation elements, compa…
Full-duplex self-backhauling is promising to provide cost-effective and flexible backhaul connectivity for ultra-dense wireless networks, but also poses a great challenge to resource management between the access and backhaul links. In this paper, we propose a user-centric joint access-backhaul transmission framework for full-duplex self-backhauled wireless networks. In the access link, user-centric clustering is adopted so that each user is cooperatively served by multiple small base stations (SBSs). In the backhaul link, user-centric multicast transmission is proposed so that each user's mes…
In this paper, we propose a wideband Full Duplex (FD) Multiple-Input Multiple-Output (MIMO) communication system comprising of an FD MIMO node simultaneously communicating with two multi-antenna UpLink (UL) and DownLink (DL) nodes utilizing the same time and frequency resources. To suppress the strong Self-Interference (SI) signal due to simultaneous transmission and reception in FD MIMO systems, we propose a joint design of Analog and Digital (A/D) cancellation as well as transmit and receive beamforming capitalizing on baseband Orthogonal Frequency-Division Multiplexing (OFDM) signal modelin…
For a self-sustaining wireless communication system in Internet-of-Things (IoT) networks, energy harvesting (EH) can be implemented at each user node as a constant renewable power supply source. Hence, an investigation into the use of wireless powered communication network (WPCN) protocols to facilitate communication between an access point (AP) and multiple mobile users (MUs) is presented in this paper. The AP has multiple antennas and operates in the full-duplex (FD) mode. The MUs, on the other hand, have single antennas and works in the half-duplex (HD) mode. Each MU communicating with the …
The full-duplex (FD) communication can achieve higher spectrum efficiency than conventional half-duplex (HD) communication; however, self-interference (SI) is the key hurdle. This paper is the first work to propose the intelligent Omni surface (IOS)-assisted FD multi-input single-output (MISO) FD communication systems to mitigate SI, which solves the frequency-selectivity issue. In particular, two types of IOS are proposed, energy splitting (ES)-IOS and mode switching (MS)-IOS. We aim to maximize data rate and minimize SI power by optimizing the beamforming vectors, amplitudes and phase shifts…
In massive multiple-input multiple-output (MIMO) systems, hybrid analog-digital beamforming is an essential technique for exploiting the potential array gain without using a dedicated radio frequency chain for each antenna. However, due to the large number of antennas, the conventional channel estimation and hybrid beamforming algorithms generally require high computational complexity and signaling overhead. In this work, we propose an end-to-end deep-unfolding neural network (NN) joint channel estimation and hybrid beamforming (JCEHB) algorithm to maximize the system sum rate in time-division…
Full-duplex (FD) systems have emerged as an es- sential enabling technology to further increase the data rate of wireless communication systems. The key idea of FD is to serve multiple users over the same bandwidth with a base station (BS) that can simultaneously transmit and receive the signals. The most challenging issue in designing an FD system is to address both the harmful effects of residual self-interference caused by the transmit-to-receive antennas at the BS as well as the co- channel interference from an uplink user (ULU) to a downlink user (DLU). An efficient solution to these prob…
