In-band full-duplex systems promise to further increase the throughput of wireless systems, by simultaneously transmitting and receiving on the same frequency band. However, concurrent transmission generates a strong self-interference signal at the receiver, which requires the use of cancellation techniques. A wide range of techniques for analog and digital self-interference cancellation have already been presented in the literature. However, their evaluation focuses on cases where the underlying physical parameters of the full-duplex system do not vary significantly. In this paper, we focus on adaptive digital cancellation, motivated by the fact that physical systems change over time. We examine some of the different cancellation methods in terms of their performance and implementation complexity, considering the cost of both cancellation and training. We then present a comparative analysis of all these methods to determine which perform better under different system performance requirements. We demonstrate that with a neural network approach, the reduction in arithmetic complexity for the same cancellation performance relative to a state-of-the-art polynomial model is several orders of magnitude.
This article provides an overview of research on full-duplex at the University of California, Riverside, in the past decade. This research was initially focused on self-interference (SI) cancellation, then moved to applications of full-duplex to improve network spectral efficiency, and in recent years advanced to discover full-duplex's potentials for wireless network security. The research on SI cancellation has resulted in both hardware-based SI cancellation results and some advanced theoretical architectures which show promises but are yet to be tested via advanced hardware implementations. …
In-band full-duplex systems are able to transmit and receive information simultaneously on the same frequency band. Due to the strong self-interference caused by the transmitter to its own receiver, the use of non-linear digital self-interference cancellation is essential. In this work, we present a hardware architecture for a neural network based non-linear self-interference canceller and we compare it with our own hardware implementation of a conventional polynomial based canceller. We show that, for the same cancellation performance, the neural network canceller has a significantly higher t…
In this paper, we focus on reduced complexity full duplex Multiple-Input Multiple-Output (MIMO) systems and present a joint design of digital transmit and receive beamforming with Analog and Digital (A/D) self-interference cancellation. We capitalize on a recently proposed multi-tap analog canceller architecture, whose number of taps does not scale with the number of transceiver antennas, and consider practical transmitter impairments for the full duplex operation. Particularly, transmitter IQ imbalance and nonlinear power amplification are assumed via relevant realistic models. Aiming at supp…
Reconfigurable intelligent surfaces (RIS) are a key enabler of various new applications in 6G smart radio environments. By utilizing an RIS prototype system, this paper aims to enhance self-interference (SI) cancellation for in-band full-duplex (FD) communication systems. SI suppression is a crucial requirement for FD communication as the SI severely limits the performance of a node by shadowing the received signal from a distant node with its own transmit signal. To this end, we propose to assist SI cancellation by exploiting an RIS to form a suitable cancellation signal in the analog domain.…
There have been recent works on enabling in-band full-duplex operation using millimeter-wave (mmWave) transceivers. These works are based solely on creating sufficient isolation between a transceiver's transmitter and receiver via multiple-input multiple-output (MIMO) precoding and combining. In this work, we propose supplementing these beamforming strategies with analog self-interference cancellation (A-SIC). By leveraging A-SIC, a portion of the self-interference is cancelled without the need for beamforming, allowing for more optimal beamforming strategies to be used in serving users. We us…
Single-antenna full-duplex communication technology has the potential to substantially increase spectral efficiency. However, limited propagation domain cancellation of single-antenna system results in a higher impact of receiver chain nonlinearities on the residual self-interference (SI) signal. In this paper, we offer a comprehensive SI model for single-antenna full-duplex systems based on direct-conversion transceiver structure considering nonlinearities of all the transceiver radio frequency (RF) components, in-phase/quadrature (IQ) imbalances, phase noise effect, and receiver noise figure…
For future wireless communication systems, full duplex is seen as a possible solution to the ever present spectrum shortage. The key aspect to enable In-Band Full Duplex (IBFD) is sufficient cancellation of the unavoidable Self-Interference (SI). In this work we evaluate the performance of a low complexity IBFD transceiver, including the required analog and digital interference cancellation techniques. The Radio Frequency Self- Interference Canceler (RFSIC) is based on the isolation of a circulator in combination with a vector modulator regenerating the interference signal, to destructively co…
In-band full-duplex systems allow for more efficient use of temporal and spectral resources by transmitting and receiving information at the same time and on the same frequency. However, this creates a strong self-interference signal at the receiver, making the use of self-interference cancellation critical. Recently, neural networks have been used to perform digital self-interference with lower computational complexity compared to a traditional polynomial model. In this paper, we examine the use of advanced neural networks, such as recurrent and complex-valued neural networks, and we perform …
In recent years, there has been extensive research on millimeter-wave (mmWave) communication and on in-band full-duplex (FD) communication, but work on the combination of the two is relatively lacking. FD mmWave systems could offer increased spectral efficiency and decreased latency while also suggesting the redesign of existing mmWave applications. While FD technology has been well-explored for sub-6 GHz systems, the developed methods do not translate well to mmWave. This turns us to a method called beamforming cancellation (BFC), where the highly directional mmWave beams are steered to mitig…
We consider a bidirectional in-band full-duplex (FD) multiple-input multiple-output (MIMO) system subject to imperfect channel state information (CSI), hardware distortion, and limited analog cancellation capability as well as the self-interference (SI) power requirement at the receiver analog domain so as to avoid the saturation of low noise amplifier (LNA). A novel minimum mean square error (MMSE)-based joint design of digital precoder and combiner for SI cancellation is offered, which combines the well-known gradient projection method and non-monotonicity considered in recent machine-learni…
One of the main obstacles in full-duplex radios is analog-to-digital converter (ADC) saturation on a receiver due to the strong self-interference (SI). To solve this issue, researchers have proposed two different types of analog self-interference cancellation (SIC) methods -- i) passive suppression and ii) regeneration-and-subtraction of SI. For the latter case, the tunable RF component, such as a multi-tap circuit, reproduces and subtracts the SI. The resolutions of such RF components constitute the key factor of the analog SIC. Indeed, they are directly related to how well the SI is imitated…
Millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems have been considered as one of the primary candidates for the fifth generation (5G) and beyond 5G wireless communication networks to satisfy the ever-increasing capacity demands. Full-duplex technology can further enhance the advantages of mmWave massive MIMO systems. However, strong self-interference (SI) is the major limiting factor in full-duplex technology. Hence, this paper proposes a novel angular-based joint hybrid precoding/combining (AB-JHPC) technique for the full-duplex mmWave massive-MIMO systems. Our pr…
Full-duplex (FD) systems have the capability to transmit and receive at the same time in the same frequency band. FD systems can reduce congestion and latency and improve coverage and spectral efficiency. As a relay, they can increase range and decrease outages. Full-duplex (FD) wireless systems have been emerging as a practical solution to provide high bandwidth, low latency, and big data processing in millimeter wave and Terahertz systems to support cellular networks, autonomous driving, platooning, advanced driving assistance and other systems. However, FD systems suffer from loopback self-…
The wide bandwidths offered at millimeter-wave (mmWave) frequencies have made them an attractive choice for future wireless communication systems. Recent works have presented beamforming strategies for enabling in-band full-duplex (FD) capability at mmWave even under the constraints of hybrid beamforming, extending the exciting possibilities of next-generation wireless. Existing mmWave FD designs, however, do not consider frequency-selective mmWave channels. Wideband communication at mmWave suggests that frequency-selectivity will likely be of concern since communication channels will be on th…
A photonic approach for radio-frequency (RF) self-interference cancellation (SIC) incorporated in an in-band full-duplex radio-over-fiber system is proposed. A dual-polarization binary phase-shift keying modulator is used for dual-polarization multiplexing at the central office (CO). A local oscillator signal and an intermediate-frequency signal carrying the downlink data are single-sideband modulated on the two polarization directions of the modulator, respectively. The optical signal is then transmitted to the remote unit, where the optical signals in the two polarization directions are spli…
A digitally-assisted photonic analog domain self-interference cancellation (SIC) and frequency downconversion method is proposed for in-band full-duplex multiple-input multiple-output (MIMO) systems using the least square (LS) algorithm with adaptive order. The SIC and frequency downconversion are achieved in the optical domain via a dual-parallel Mach-Zehnder modulator (DP-MZM), while the downconverted signal is processed by the LS algorithm with adaptive order that is used to track the response of the multipath self-interference (SI) channel and reconstruct the reference signal for SIC. The …
Full-duplex systems require very strong self-interference cancellation in order to operate correctly and a significant part of the self-interference signal is due to non-linear effects created by various transceiver impairments. As such, linear cancellation alone is usually not sufficient and sophisticated non-linear cancellation algorithms have been proposed in the literature. In this work, we investigate the use of a neural network as an alternative to the traditional non-linear cancellation method that is based on polynomial basis functions. Measurement results from a full-duplex testbed de…
This work develops LoneSTAR, a novel enabler of full-duplex millimeter wave (mmWave) communication systems through the design of analog beamforming codebooks. LoneSTAR codebooks deliver high beamforming gain and broad coverage while simultaneously reducing the self-interference coupled by transmit and receive beams at a full-duplex mmWave transceiver. Our design framework accomplishes this by tolerating some variability in transmit and receive beamforming gain to strategically shape beams that reject self-interference spatially while accounting for digitally-controlled analog beamforming netwo…
This paper addresses the performance of a full-duplex (FD) generalized frequency division multiplexing (GFDM) transceiver in the presence of radio frequency (RF) impairments including phase noise, carrier frequency offset (CFO) and in-phase (I) and quadrature (Q) imbalance. We study analog and digital self-interference (SI) cancellation and develop a complementary SI suppression method. Closed-form solutions for the residual SI power and the desired signal power and signal-to-interference ratio (SIR) are provided. Simulation results show that the RF impairments degrade SI cancellation and FD G…
Photonics-assisted analog wideband self-interference cancellation for in-band full-duplex MIMO systems with adaptive digital amplitude and delay pre-matching
Self-interference (SI) is the main obstacle to full-duplex radios. To overcome the SI, researchers have proposed several analog and digital domain self-interference cancellation (SIC) techniques. How well the digital cancellation works depends on the results of analog cancellation. Therefore, to analyze overall SIC performance, one should do so in an integrated manner. In this paper, we build a simulator that can analyze the performance of analog and digital SIC techniques. Through this simulator, we can analyze the overall SIC performance within various system parameters such as the resolutio…
The wireless in-band full-duplex (IBFD) technology can in theory double the system capacity over the conventional frequency division duplex (FDD) or time-division duplex (TDD) alternatives. But the strong self-interference of the IBFD can cause excessive quantization noise in the analog-to-digital converters (ADC), which represents the hurdle for its real implementation. In this paper, we consider employing a reconfigurable intelligent surface (RIS) for IBFD communications. While the BS transmits and receives the signals to and from the users simultaneously on the same frequency band, it can a…
In this letter, we propose a modified version of Fast Independent Component Analysis (FICA) algorithm to solve the self-interference cancellation (SIC) problem in In-band Full Duplex (IBFD) communication systems. The complex mixing problem is mathematically formulated to suit the real-valued blind source separation (BSS) algorithms. In addition, we propose a method to estimate the ambiguity factors associated with ICA lumped together with the channels and residual separation error. Experiments were performed on an FD platform where FICA-based BSS was applied for SIC in the frequency domain. Ex…
Although the hardware complexity of the analog self-interference canceller in full duplex Multiple Input Multiple Output (MIMO) designs does not necessarily scale with the number of transceiver antennas, exploiting the benefits of analog cancellation in massive MIMO systems with hundreds of antenna elements is still quite impractical. Hybrid Analog and Digital (A/D) beamforming architectures have been lately considered as a candidate technology for realizing massive MIMO transceivers with very large number of antenna elements, but with much fewer numbers of Radio Frequency (RF) chains. In this…
Modern millimeter wave (mmWave) communication systems rely on beam alignment to deliver sufficient beamforming gain to close the link between devices. We present a novel beam selection methodology for multi-panel, full-duplex mmWave systems, which we call STEER, that delivers high beamforming gain while significantly reducing the full-duplex self-interference coupled between the transmit and receive beams. STEER does not necessitate changes to conventional beam alignment methodologies nor additional over-the-air feedback, making it compatible with existing cellular standards. Instead, STEER us…
Memorial University（纪念大学）；Benha University（本哈大学）；Huawei Technologies Canada Co., Ltd.（华为技术加拿大有限公司）
Self-interference (SI) is considered as a main challenge in full-duplex (FD) systems. Therefore, efficient SI cancelers are required for the influential deployment of FD systems in beyond fifth-generation wireless networks. Existing methods for SI cancellation have mostly considered the polynomial representation of the SI signal at the receiver. These methods are shown to operate well in practice while requiring high computational complexity. Alternatively, neural networks (NNs) are envisioned as promising candidates for modeling the SI signal with reduced computational complexity. Consequentl…
Non-orthogonal multiple access (NOMA) is an interesting concept to provide higher capacity for future wireless communications. In this article, we consider the feasibility and benefits of combining full-duplex operation with NOMA for modern communication systems. Specifically, we provide a comprehensive overview on application of full-duplex NOMA in cellular networks, cooperative and cognitive radio networks, and characterize gains possible due to full-duplex operation. Accordingly, we discuss challenges, particularly the self-interference and inter-user interference and provide potential solu…
We present measurements of the 28 GHz self-interference channel for full-duplex sectorized multi-panel millimeter wave (mmWave) systems, such as integrated access and backhaul. We measure the isolation between the input of a transmitting phased array panel and the output of a co-located receiving phased array panel, each of which is electronically steered across a number of directions in azimuth and elevation. In total, nearly 6.5 million measurements were taken in an anechoic chamber to densely inspect the directional nature of the coupling between 256-element phased arrays. We observe that h…
Channel estimation and optimal training sequence design for full-duplex one-way relays are investigated. We propose a training scheme to estimate the residual self-interference (RSI) channel and the channels between nodes simultaneously. A maximum likelihood estimator is implemented with Broyden-Fletcher-Goldfarb-Shanno (BFGS) algorithm. In the presence of RSI, the overall source-to-destination channel becomes an inter-symbol-interference (ISI) channel. With the help of estimates of the RSI channel, the destination is able to cancel the ISI through equalization. We derive and analyze the Crame…
In this paper, we provide an analytical framework for full-duplex (FD) massive multiple-input multiple-output (MIMO) cellular networks with low resolution analog-to-digital and digital-to-analog converters (ADCs and DACs). Matched filters are employed at the FD base stations (BSs) at the transmit and receive sides. For both reverse and forward links, our contributions are (1) derivations of the signal-to-quantization-plus-interference-and-noise ratio (SQINR) for general and special cases; (2) derivations of spectral efficiency for asymptotic cases as well as for power scaling laws; and (3) qua…
This letter presents a device-to-device (D2D) enabling cellular full-duplex (FD) cooperative protocol using non-orthogonal multiple access (NOMA), where an FD relay assists in relaying NOMA far user's signal and transmits a D2D receiver's signal simultaneously. The ergodic capacity, outage probability, and diversity order of the proposed protocol are theoretically investigated under the realistic assumption of imperfect self and known interference cancellation. The Outcome of the investigation demonstrates the performance gain of the suggested protocol over conventional FD cooperative NOMA sys…
Equipping millimeter wave (mmWave) systems with full-duplex capability would accelerate and transform next-generation wireless applications and forge a path for new ones. Full-duplex mmWave transceivers could capitalize on the already attractive features of mmWave communication by supplying spectral efficiency gains and latency improvements while also affording future networks with deployment solutions in the form of interference management and wireless backhaul. Foreseeable challenges and obstacles in making mmWave full-duplex a reality are presented in this article along with noteworthy unkn…
Wireless communication systems can be enhanced at the link level, in medium access, and at the network level when transceivers are equipped with full-duplex capability: the transformative ability to simultaneously transmit and receive over the same frequency spectrum. Effective methods to cancel self-interference are required to facilitate full-duplex operation, which we overview herein in the context of traditional radios, along with those in next-generation wireless networks. We highlight advances in self-interference cancellation that leverage machine learning, and we summarize key consider…
Interference cancellation is the main driving technology in enhancing the transmission rates over telephone lines above 100 Mbps. Still, crosstalk interference in multi-pair digital subscriber line (DSL) systems at higher frequencies has not been dealt with sufficiently. The upcoming G.(mg) fast DSL system envisions the use of extremely high bandwidth and full-duplex transmissions generating significantly higher crosstalk and self-interference signals. More powerful interference cancellation techniques are required to enable multi-gigabit per second data rate transmission over copper lines. In…
Full-duplex (FD) communication is a promising candidate to address the data rate limitations in underwater acoustic (UWA) channels. Because of transmission at the same time and on the same frequency band, the signal from the local transmitter creates self-interference (SI) that contaminates the signal from the remote transmitter. At the local receiver, channel state information for both the SI and remote channels is required to remove the SI and equalize the SI-free signal, respectively. However, because of the rapid time-variations of the UWA environment, real-time tracking of the channels is…
In this paper, we propose a wideband Full Duplex (FD) Multiple-Input Multiple-Output (MIMO) communication system comprising of an FD MIMO node simultaneously communicating with two multi-antenna UpLink (UL) and DownLink (DL) nodes utilizing the same time and frequency resources. To suppress the strong Self-Interference (SI) signal due to simultaneous transmission and reception in FD MIMO systems, we propose a joint design of Analog and Digital (A/D) cancellation as well as transmit and receive beamforming capitalizing on baseband Orthogonal Frequency-Division Multiplexing (OFDM) signal modelin…
The full-duplex (FD) communication can achieve higher spectrum efficiency than conventional half-duplex (HD) communication; however, self-interference (SI) is the key hurdle. This paper is the first work to propose the intelligent Omni surface (IOS)-assisted FD multi-input single-output (MISO) FD communication systems to mitigate SI, which solves the frequency-selectivity issue. In particular, two types of IOS are proposed, energy splitting (ES)-IOS and mode switching (MS)-IOS. We aim to maximize data rate and minimize SI power by optimizing the beamforming vectors, amplitudes and phase shifts…
In this paper, we study Full Duplex (FD) Multiple-Input Multiple-Output (MIMO) radios for simultaneous data communication and control information exchange. Capitalizing on a recently proposed FD MIMO architecture combining digital transmit and receive beamforming with reduced complexity multi-tap analog Self-Interference (SI) cancellation, we propose a novel transmission scheme exploiting channel reciprocity for joint downlink beamformed information data communication and uplink channel estimation through training data transmission. We adopt a general model for pilot-assisted channel estimatio…
