Significant progress has been made to develop silicon pixel technologies for use in the vertex and tracker regions of the proposed Compact Linear Collider (CLIC) detector design. The electron-positron collisions generated by this linear accelerator provide a clean, low-radiation environment for the inner detectors. However, physics-driven performance targets, the CLIC beam structure, and occupancies from beam-induced backgrounds place challenging requirements on detector technologies for this region. A pixel pitch down to 25 x 25$μ$m$^{-2}$, material budget $\leq$ 0.2-2$\%X_0$ per layer, average power dissipation of down to 50mWcm$^{-2}$, position resolution of 3-7$μ$m, and timing resolution as low as 5ns are called for in the vertex and tracking detectors. To this aim, a comprehensive R&D programme is ongoing to design and test silicon pixel detectors to fulfil these specifications, including both monolithic and hybrid devices. These studies involve Allpix$^2$ Monte Carlo and TCAD simulations, advanced 65nm ASIC and sensor design, laboratory testing, and beam tests of individual modules to determine the required performance parameters. The characterisation and simulation modelling of these devices has also lead to the development of a set of tools and software within the CLIC detector and physics (CLICdp) collaboration. This publication will present recent results from the technologies being developed and tested in view of the CLIC vertex and tracking detector requirements, such as various monolithic CMOS sensors, and fine pitch hybrid assemblies with planar sensors.
The physics aims at the proposed high-energy $e^+e^-$ collider CLIC pose challenging demands on the performance of the detector system. Precise hit-time tagging, an excellent spatial resolutions, and a low mass are required for the vertex and tracking detectors. To meet these requirements, an all-silicon vertex and tracking detector system is foreseen, for which a broad R&D programme on a variety of novel silicon detector technologies is being pursued. For the ultra-low mass vertex detector, different hybrid technologies with innovative sensor concepts and interconnection techniques are explor…
Thin planar silicon sensors with a pitch of 55um, active edge and various guard ring layouts are investigated, using two-dimensional finite-element T-CAD simulations. The simulation results have been compared to experimental data, and an overall good agreement is observed. It is demonstrated that 50um thin planar silicon sensors with active edge with floating guard ring or without guard ring can be operated fully efficiently up to the physical edge of the sensor. The simulation findings are used to identify suitable sensor designs for application in the high-precision vertex detector of the fu…
The concept of capacitive coupling between sensors and readout chips is under study for the vertex detector at the proposed high-energy CLIC electron positron collider. The CLICpix Capacitively Coupled Pixel Detector (C3PD) is an active High-Voltage CMOS sensor, designed to be capacitively coupled to the CLICpix2 readout chip. The chip is implemented in a commercial $180$ nm HV-CMOS process and contains a matrix of $128\times128$ square pixels with $25$ $μ$m pitch. First prototypes have been produced with a standard resistivity of $\sim20$ $Ω$cm for the substrate and tested in standalone mode.…
Conformal tracking is an innovative track finding strategy adopted for the detector at the Compact Linear Collider (CLIC), a proposed future electron-positron collider. It features a pattern recognition in a conformal-mapped plane using the cellular automaton algorithm to reconstruct the trajectory of charged particles in a magnetic field. The efficiency and robustness of the algorithm are validated using full-simulation studies in the challenging beam-induced background conditions expected for the 3 TeV stage of the CLIC collider. The tracking performance requirements, set by the ambitious CL…
The physics aims at the proposed future high-energy linear $e^+e^-$ collider CLIC pose challenging demands on the performance of the detector system. In particular, the vertex and tracking detectors have to combine a spatial resolution of a few micrometres and a low material budget with a time-stamping accuracy of a few nanoseconds. For the vertex detector, fine-pitch sensors, dedicated 65nm readout ASICs, fine-pitch bonding techniques using solder bumps or anisotropic conductive films as well as monolithic devices based on Silicon-On-Insulator technology are explored. Fully monolithic CMOS se…
A detector concept based on hybrid planar pixel-detector technology is under development for the CLIC vertex detector. It comprises fast, low-power and small-pitch readout ASICs implemented in 65 nm CMOS technology (CLICpix) coupled to ultra-thin sensors via low-mass interconnects. The power dissipation of the readout chips is reduced by means of power pulsing, allowing for a cooling system based on forced gas flow. In this paper the CLIC vertex-detector requirements are reviewed and the current status of R&D on sensors, readout and detector integration is presented.
The dense beams used at CLIC to achieve a high luminosity will cause a large amount of background particles through beam-beam interactions. Generator level studies with GuineaPig and full detector simulation studies with an ILD based CLIC detector have been performed to evaluate the amount of beam-beam background hitting the vertex detector.
CLIC is a proposed linear $e^{+}e^{-}$ collider with center-of-mass energies of up to $3\,\textrm{TeV}$. Its main objectives are precise top quark and Higgs boson measurements, as well as searches for Beyond Standard Model physics. To meet the physics goals, the vertex and tracking detectors require not only a spatial resolution of a few micrometers and a very low material budget, but also timing capabilities with a precision of a few nanoseconds to allow suppression of beam-induced backgrounds. Different technologies using hybrid silicon detectors are explored for the vertex detectors, such a…
CLIC is a proposed linear e+e- collider designed to provide particle collisions at center-of-mass energies of up to 3 TeV. Precise measurements of the properties of the top quark and the Higgs boson, as well as searches for Beyond the Standard Model physics require a highly performant CLIC detector. In particular the vertex detector must provide a single point resolution of only a few micrometers while not exceeding the envisaged material budget of around 0.2% X0 per layer. Beam-beam interactions and beamstrahlung processes impose an additional requirement on the timestamping capabilities of t…
In order to achieve the challenging requirements on the CLIC vertex detector, a range of technology options have been considered in recent years. One prominent idea is the use of active sensors implemented in a commercial high-voltage CMOS process, capacitively coupled to hybrid pixel readout chips. Recent results have shown the approach to be feasible, though more detailed studies of the performance of such devices, including simulation, are required. The CLICdp collaboration has developed a number of ASICs as part of its vertex detector R&D programme, and here we present results on the perfo…
Several algorithms for tracking and for primary and secondary vertex reconstruction have been developed by the ATLAS collaboration following different approaches. This has allowed a thorough cross-check of the performances of the algorithms and of the reconstruction software. The results of the most recent studies on this topic are discussed and compared.
CLIC is a proposed linear $e^+e^-$ collider with center-of-mass energies of up to 3 TeV. Its main objectives are precise top quark, Higgs boson and Beyond Standard Model physics. In addition to spatial resolutions of a few micrometers and a very low material budget, the vertex and tracking detectors also require timing capabilities with a precision of a few nanoseconds to allow suppression of beam-induced background particles. Different technologies using hybrid silicon detectors are explored for the vertex detectors, such as dedicated 65 nm readout ASICs, small-pitch sensors as well as bondin…
The anticipated physics program at an high energy e+e- linear collider places special emphasis on the accuracy in extrapolating charged particle tracks to their production vertex to tag heavy quarks and leptons. This paper reviews physics motivations and performance requirements, sensor R&D directions and current results of the studies for a vertex tracker at a future linear collider.
One of the major physics goals at the ILC is the precise measurement of the Higgs coupling constants to b-quarks and c-quarks. To achieve this measurement, we need a high-performance vertex detector leading to precise flavor tagging. For this purpose, we are developing the Fine Pixel CCD (FPCCD) vertex detector. In this paper, we will report on the development status of FPCCDTrackFinder, a new track finder improving tracking efficiency, especially in the low $p_t$ region, and an evaluation result of the flavor tagging performance with FPCCDTrackFinder in the FPCCD vertex detector.
This report reviews current trends in the R&D of semiconductor pixellated sensors for vertex tracking and radiation imaging. It identifies requirements of future HEP experiments at colliders, needed technological breakthroughs and highlights the relation to radiation detection and imaging applications in other fields of science.
The harsh machine background at the Compact Linear Collider (CLIC) forms a strong constraint on the design of the innermost part of the tracker. For the CLIC Conceptual Design Report, the detector concepts developed for the International Linear Collider (ILC) were adapted to the CLIC environment. We present the new layout for the Vertex Detector and the Forward Tracking Disks of the CLIC detector concepts, as well as the background levels in these detectors. We also study the dependence of the background rates on technology parameters like thickness of the active layer and detection threshold.
The Compact Linear Collider CLIC is designed to deliver e+e- collisions at a center of mass energy of up to 3 TeV. The detector systems at this collider have to provide highly efficient tracking and excellent jet energy resolution and hermeticity for multi-TeV final states with multiple jets and leptons. In addition, the detector systems have to be capable of distinguishing physics events from large beam-induced background at a crossing frequency of 2 GHz. Like for the detector concepts at the ILC, CLIC detectors are based on event reconstruction using particle flow algorithms. The two detecto…
We present results of a study of charged particle track and vertex reconstruction with a beam telescope made of four layers of 50 micron-thin CMOS monolithic pixel sensors using the 120 GeV protons at the FNAL Meson Test Beam Facility. We compare our results to the performance requirements of a future e+e- linear collider in terms of particle track extrapolation and vertex reconstruction accuracies.
The CLIC Tracker Detector (CLICTD) is a monolithic pixelated sensor chip produced in a $180$ nm imaging CMOS process built on a high-resistivity epitaxial layer. The chip, designed in the context of the CLIC tracking detector study, comprises a matrix of ${16\times128}$ elongated pixels, each measuring ${300\times30}$ $μ$m$^2$. To ensure prompt charge collection, every elongated pixel is segmented in eight sub-pixels, each containing a collection diode and a separate analog front-end. A simultaneous $8$-bit time measurement with $10$ ns time bins and $5$-bit energy measurement with programmabl…
The physics aims at the proposed future CLIC high-energy linear $e^+ e^-$ collider pose challenging demands on the performance of the detector system. In particular the vertex and tracking detectors have to combine precision measurements with robustness against the expected high rates of beam-induced backgrounds. A spatial resolution of a few microns and a material budget down to 0.2\% of a radiation length per vertex-detector layer have to be achieved together with a few nanoseconds time stamping accuracy. These requirements are addressed with innovative technologies in an ambitious detector …
CLICTD is a monolithic silicon pixel sensor fabricated in a modified 180 nm CMOS imaging process with a small collection electrode design and a high-resistivity epitaxial layer. It features an innovative sub-pixel segmentation scheme and is optimised for fast charge collection and high spatial resolution. The sensor was developed to target the requirements for the tracking detector of the proposed future Compact Linear Collider (CLIC). Most notably, a temporal resolution of a few nanoseconds and a spatial resolution below 7 microns are demanded. In this contribution, the sensor performance mea…
The CLIC Tracker Detector (CLICTD) is a monolithic pixel sensor. It is fabricated in a 180 nm CMOS imaging process, modified with an additional deep low-dose n-type implant to obtain full lateral depletion. The sensor features a small collection diode, which is essential for achieving a low input capacitance. The CLICTD sensor was designed as a technology demonstrator in the context of the tracking detector studies for the Compact Linear Collider (CLIC). Its design characteristics are of broad interest beyond CLIC, for HL-LHC tracking detector upgrades. It is produced in two different pixel fl…
The Compact Linear Collider (CLIC) is a concept for a future linear collider that would provide e$^+$e$^-$ collisions at up to 3 TeV. The physics aims require a detector system with excellent jet energy and track momentum resolution, highly efficient flavour tagging and lepton identification capabilities, full geometrical coverage extending to low polar angles, and timing information of the order of nanoseconds to reject beam-induced background. To deal with these requirements, an extensive R&D programme is in place to overcome current technological limits. The CLIC detector concept includes a…
In this report the test beam requirements for the vertex detector and the tracking detector for ILC are discussed. It focuses on the infrastructure needs of the different subsystems. In the second part of this summary the ideas about future infrastructure above the immediate needs are summarised.
This paper presents a study of vertex tracking with a beam hodoscope consisting of three layers of monolithic pixel sensors in SOI technology on high-resistivity substrate. We study the track extrapolation accuracy, two-track separation and vertex reconstruction accuracy in pion-Cu interactions with 150 and 300 GeV/c pions at the CERN SPS. Results are discussed in the context of vertex tracking at future lepton colliders.
Belle II is a $B$ factory experiment aiming to start physics data taking in 2017. It is currently being set up at the SuperKEKB accelerator at the KEK facility in Tsukuba (Japan), an asymmetric $e^+e^-$ collider which aims to achieve an unprecedented instantaneous luminosity of $8\cdot10^{35} \textrm{Hz}/\textrm{cm}^2$. This forty-fold increase over predecessor experiments is achieved by employing a novel nano-beam scheme. Originally developed for the now-defunct SuperB experiment, this scheme allows a significant increase in luminosity at only modest increases of beam currents. Challenges for…
Pixel vertex detectors are THE instrument of choice for the tracking of charged particles close to the interaction point at the LHC. Hybrid pixel detectors, in which sensor and read-out IC are separate entities, constitute the present state of the art in detector technology. Three of the LHC detectors use vertex detectors based on this technology. A development period of almost 10 years has resulted in pixel detector modules which can stand the extreme rate and timing requirements as well as the very harsh radiation environment at the LHC for its full life time and without severe compromises i…
The BABAR Silicon Vertex Tracker (SVT) is a five-layer double-sided silicon detector designed to provide precise measurements of the position and direction of primary tracks, and to fully reconstruct low-momentum tracks produced in e+e- collisions at the PEP-II asymmetric collider at Stanford Linear Accelerator Center. This paper describes the design, implementation, performance, and validation of the local alignment procedure used to determine the relative positions and orientations of the 340 SVT wafers. This procedure uses a tuned mix of in-situ experimental data and complementary lab-bench…
The ALICE apparatus includes an Inner Tracking System for high-precision vertexing and tracking at midrapidity. Thanks to this detector, remarkable results were obtained with Run 2 data in all collision systems studied at the LHC. In this contribution, the role of the ITS in the event, track and secondary vertex reconstruction is highlighted, and the comparison of the resolution on the track impact parameter to the collision point in data and Monte Carlo simulations is reported. Finally, some of the main physics results obtained in pp and Pb--Pb collisions relying on the excellent ALICE vertex…
The Compact Linear Collider (CLIC) is a high-energy high-luminosity linear electron-positron collider under development. It is foreseen to be built and operated in three stages, at centre-of-mass energies of 380 GeV, 1.5 TeV and 3 TeV, respectively. It offers a rich physics program including direct searches as well as the probing of new physics through a broad set of precision measurements of Standard Model processes, particularly in the Higgs-boson and top-quark sectors. The precision required for such measurements and the specific conditions imposed by the beam dimensions and time structure …
This is part of a document, which is devoted to the developments of pixel detectors in the context of the International Linear Collider. From the early developments of the MIMOSAs to the proposed DotPix I recall some of the major progresses. The need for very precise vertex reconstruction is the reason for the Research and Development of new pixel detectors, first derived from the CMOS sensors and in further steps with new semiconductors structures. The problem of radiation effects was investigated and this is the case for the noise level with emphasis of the benefits of downscaling. Specific …
The Compact Linear Collider (CLIC) is a concept for a future $e^{+}e^{-}$ linear collider with a center-of-mass energy of up to 3 TeV. The design of a CLIC experiment is driven by the requirements related to the physics goals, as well as by the experimental conditions. For example, the short time between two bunch crossings of 0.5 ns and the backgrounds due to beamstrahlung have direct impact on the design of a CLIC experiment. The Silicon Detector (SiD) is one of the concepts currently being discussed as a possible detector for the International Linear Collider (ILC). In this thesis we develo…
The architecture of the ZEUS Micro Vertex Detector data acquisition system and the implementation of its second level trigger, the ZEUS Global Track Trigger are described. Data from the vertex detectors HELIX read-out chips, corresponding to 200k channels, are digitized by 3 crates of ADCs which perform noise and pedestal subtraction, and data suppression and compaction. PowerPC VME board computers push cluster data for second level trigger processing and strip data for event building via Fast and Gigabit Ethernet network connections. Additional tracking information from the central tracking c…
The combined vertexing and tracking performance of the innermost part of the FCC-ee experiments must deliver outstanding precision for measurement of the track momentum together with an impact parameter resolution exceeding by at least a factor five that typically achieved at LHC experiments. Furthermore, precision measurements require stability and fiducial accuracy at a level which is unprecedented in collider experiments. For the innermost vertex layers these goals translate into a target hit resolution of approximately 3 $μ$m together with a material budget of around 0.2\% of a radiation l…
The Compact Linear Collider (CLIC) is a TeV-scale high-luminosity linear e$^+$e$^-$ collider under development by international collaborations hosted by CERN. This document provides an overview of the design, technology, and implementation aspects of the CLIC accelerator and the detector. For an optimal exploitation of its physics potential, CLIC is foreseen to be built and operated in stages, at centre-of-mass energies of 380 GeV, 1.5 TeV and 3 TeV, for a site length ranging between 11 km and 50 km. CLIC uses a two-beam acceleration scheme, in which normal-conducting high-gradient 12 GHz acce…
Conformal tracking is an innovative and comprehensive pattern recognition technique using a cellular automaton-based track finding performed in a conformally-mapped space. It is particularly well-suited for light-weight silicon systems with high position resolution, such as the next generation of tracking detectors designed for future electron-positron colliders. The algorithm has been developed and validated with simulated data of the CLICdet tracker. It has demonstrated not only excellent performance in terms of tracking efficiency, fake rate and track parameters resolution but also robustne…
The Pixel Detector is the innermost detector of the tracking system of the Compact Muon Solenoid (CMS) experiment at CERN Large Hadron Collider (LHC). It precisely determines the interaction point (primary vertex) of the events and the possible secondary vertexes due to heavy flavours ($b$ and $c$ quarks); it is part of the overall tracking system that allows reconstructing the tracks of the charged particles in the events and combined with the magnetic field to measure their impulsion. The pixel detector allows measuring the tracks in the region closest to the interaction point. The Level-1 (…
CMOS pixel sensors (CPS) represent a novel technological approach to building charged particle detectors. CMOS processes allow to integrate a sensing volume and readout electronics in a single silicon die allowing to build sensors with a small pixel pitch ($\sim 20 μm$) and low material budget ($\sim 0.2-0.3\% X_0$) per layer. These characteristics make CPS an attractive option for vertexing and tracking systems of high energy physics experiments. Moreover, thanks to the mass production industrial CMOS processes used for the manufacturing of CPS the fabrication construction cost can be signifi…
CMOS Pixel Sensors tend to become relevant for a growing spectrum of charged particle detection instruments. This comes mainly from their high granularity and low material budget. However, several potential applications require a higher read-out speed and radiation tolerance than those achieved with available devices based on a 0.35 micrometers feature size technology. This paper shows preliminary test results of new prototype sensors manufactured in a 0.18 micrometers process based on a high resistivity epitaxial layer of sizeable thickness. Grounded on these observed performances, we discuss…
The hit response of silicon vertex and tracking detectors to muon collider beam background and results of a study of hit reducing techniques are presented. The background caused by decays of the 750 GeV/c m+ and m- beams was simulated using the MARS15 program, which included the infrastructure of the beam line elements near the detector and the 10 degree nozzles that shield the detector from this background. The ILCRoot framework, along with the Geant4 program, was used to simulate the hit response of the silicon vertex and tracker detectors to the muon decay background remaining after the shi…
Calorimeter-assisted track finding algorithm takes advantage of the finely segmented electromagnetic calorimeter proposed for the SiD detector concept by looking for "MIP stubs" produced by charged particles in the calorimeter, and using them as seeds for pattern recognition in the tracker. The algorithm allows for efficient reconstruction of tracks that cannot be found using seeds provided by the vertex detector, even if standalone pattern recognition in the outer tracker is difficult. The algorithm has been implemented as a package in the org.lcsim framework. Current status of the package an…
The High Luminosity upgrade of the CERN Large Hadron Collider will be able to reach a peak instantaneous luminosity of 5E34/cm2 s. The innermost detectors of the CMS and ATLAS experiments will have to cope with unprecedented requirements on radiation hardness. At the end of the operation period, radiation levels are expected to reach values above 2.6E16 neq/cm2. Sensors based on 3D pixel technology, with intrinsic radiation tolerance, are the baseline option for the innermost layers of the vertex detectors of several HL-LHC experiments. This article gives an overview of the ongoing characteriz…
The Silicon Vertex Detector of Belle II is a state-of-the-art tracking and vertexing system based on double-sided silicon strip sensors, designed and fabricated by a large international collaboration in the period 2012--2018. Since 2019 it has been in operation providing high quality data with a small number of defective channels (<1%), a large hit-finding efficiency (>99%), a good signal-to-noise ratio (well in excess of 10 for all sensor configurations and tracks). Together with the good control over the alignment, these are all essential factors to achieve good tracking reconstruction and p…
The CMS-TOTEM Precision Proton Spectrometer (CT-PPS) is an approved project to add tracking and timing information at approximately $\pm$210~m from the interaction point around the CMS detector. It is designed to operate at high luminosity with up to 50 interactions per 25~ns bunch crossing to perform measurements of e.g. the quartic gauge couplings and search for rare exclusive processes. During 2016, CT-PPS took data in normal high-luminosity proton-proton LHC collisions. In the coming years, high radiation doses and large multiple-vertex interactions will represent difficult challenges that…
This paper presents an investigation of the use of interest point detection algorithms from image processing applied to reconstruction of interactions in high granularity tracking detectors. Their purpose is to extract keypoints from the data as input to higher level reconstruction algorithms, replacing the role of human operators in event selection and reconstruction guidance. Simulations of nu_mu charged current events in a small liquid argon time projection chamber are used as a concrete example of a modern high granularity tracking detector. Data from the simulations are used to characteri…
Development and demonstration of the Korea ALICE Telescope using electron beams at KEK PF-AR
Inha University（仁荷大学）；Pusan National University（釜山国立大学）；University of Tsukuba（筑波大学）；University of Tokyo（东京大学）；Yonsei University（延世大学）；Hiroshima University（广岛大学）
The ALICE detector was designed to track and identify particles in a wide transverse momentum range, from more than 100 GeV/c down to ~100 MeV/c. The innermost barrel-like detector, the Inner Tracking System (ITS), is dedicated to precise tracking and to primary and secondary vertices reconstruction. In this proceeding we present the ITS performance for tracking, primary vertex reconstruction and particle identification capability. The current understanding of the detector response is the result of an extensive phase of commissioning started with 2008 cosmic-ray run and finalized with data fro…
A description is provided of the software algorithms developed for the CMS tracker both for reconstructing charged-particle trajectories in proton-proton interactions and for using the resulting tracks to estimate the positions of the LHC luminous region and individual primary-interaction vertices. Despite the very hostile environment at the LHC, the performance obtained with these algorithms is found to be excellent. For ttbar events under typical 2011 pileup conditions, the average track-reconstruction efficiency for promptly-produced charged particles with transverse momenta of pt > 0.9 GeV…
The ATLASpix high-voltage monolithic active pixel sensor (HV-MAPS) was designed as a technology demonstrator for the ATLAS ITk Upgrade and the CLIC tracking detector. In this contribution new results from laboratory-based energy calibration measurements using fluorescence X-rays are presented for the ATLASpix Simple matrix. These findings are complemented by new results from test-beam studies with inclined tracks, in which the active charge collection depth is determined.
The contribution gives an overview of the LCFIVertex package, providing software tools for high-level event reconstruction at the International Linear Collider using vertex-detector information. The package was validated using a fast Monte Carlo simulation. Performance obtained with a more realistic GEANT4-based detector simulation and realistic tracking code is presented. The influence of hadronic interactions on flavour tagging is discussed.
The use of CMOS Pixel Sensors (CPS) for high resolution and low material vertex detectors has been validated with the 2014 and 2015 physics runs of the STAR-PXL detector at RHIC/BNL. This opens the door to the use of CPS for inner tracking devices, with 10-100 times larger sensitive area, which require therefore a sensor design privileging power saving, response uniformity and robustness. The 350 nm CMOS technology used for the STAR-PXL sensors was considered as too poorly suited to upcoming applications like the upgraded ALICE Inner Tracking System (ITS), which requires sensors with one order…
We present the second in a series of studies into the forward tracking system for a future linear $ e^+ e^- $ collider with a center-of-mass energy in the range from 250 GeV to 3 TeV. In this note a number of specific challenges are investigated, that have caused a degradation of the tracking and vertexing performance in the forward region in previous experiments. We perform a quantitative analysis of the dependence of the tracking performance on detector design parameters and identify several ways to mitigate the performance loss for charged particles emitted at shallow angle.
The ATLAS Inner Detector is responsible for particle tracking in ATLAS experiment at CERN Large Hadron Collider (LHC) and comprises silicon and gas based detectors. The combination of both silicon and gas based detectors provides high precision impact parameter and momentum measurement of charged particles, with high efficiency and small fake rate. The ID has been used to exploit fully the physics potential of the LHC since the first proton-proton collisions at 7 TeV were delivered in 2009. The performance of track and vertex reconstruction is presented, as well as the operation aspects of the…
Since the start of data taking in spring 2019 at the SuperKEKB collider (KEK, Japan) the Belle II Silicon Vertex Detector (SVD) has been operating reliably and with high efficiency, while providing high quality data: high signal-to-noise ratio, greater than 99% hit efficiency, and precise spatial resolution. These attributes, combined with stability over time, result in good tracking efficiency. Currently the occupancy, dominated by beam-background hits, is quite low (about 0.5% in the innermost layer), causing no problems to the SVD data reconstruction. In view of the operation at higher lumi…
Five contemporary technologies are discussed in the context of their potential roles in particle tracking for future high energy physics applications. These include sensors of the 3D configuration, in both diamond and silicon, submicron-dimension pixels, thin film detectors, and scintillating quantum dots in gallium arsenide. Drivers of the technologies include radiation hardness, excellent position, vertex, and timing resolution, simplified integration, and optimized power, cost, and material.
