CLIC is a proposed linear $e^+e^-$ collider with center-of-mass energies of up to 3 TeV. Its main objectives are precise top quark, Higgs boson and Beyond Standard Model physics. In addition to spatial resolutions of a few micrometers and a very low material budget, the vertex and tracking detectors also require timing capabilities with a precision of a few nanoseconds to allow suppression of beam-induced background particles. Different technologies using hybrid silicon detectors are explored for the vertex detectors, such as dedicated 65 nm readout ASICs, small-pitch sensors as well as bonding using anisotropic conductive films. Monolithic sensors are the current choice for the tracking detector, and a prototype using a 180 nm high-resistivity CMOS process has been designed and produced, and is currently under evaluation. Different designs using a silicon-on-insulator process are under investigation for both vertex and tracking detector. All prototypes are tested in laboratory and beam tests, and newly developed simulation tools combining Geant4 and TCAD are used to assess and optimize their performance. This contribution gives an overview of the R&D program for the CLIC vertex and tracking detectors, highlighting new results from the prototypes.
We report recent results on the use of charge division to obtain a longitudinal coordinate from silicon strip detectors, and on sources of electronic readout noise for long, thin strips. These results hold promise for the design of Linear Collider charged particle tracking system composed of silicon microstrip sensors.
The hit response of silicon vertex and tracking detectors to muon collider beam background and results of a study of hit reducing techniques are presented. The background caused by decays of the 750 GeV/c m+ and m- beams was simulated using the MARS15 program, which included the infrastructure of the beam line elements near the detector and the 10 degree nozzles that shield the detector from this background. The ILCRoot framework, along with the Geant4 program, was used to simulate the hit response of the silicon vertex and tracker detectors to the muon decay background remaining after the shi…
The anticipated physics program at an high energy e+e- linear collider places special emphasis on the accuracy in extrapolating charged particle tracks to their production vertex to tag heavy quarks and leptons. This paper reviews physics motivations and performance requirements, sensor R&D directions and current results of the studies for a vertex tracker at a future linear collider.
The ALEPH Silicon Vertex Detector for LEP2 featured a laser survey system to monitor its mechanical stability. The analysis of laser system data from 1997 to 2000 showed that VDET suffered a time-dependent displacement. It resulted to be compatible with a deformation of the support structure that made the device to slowly rotate during the data-taking. A maximal local displacement of ~20 microns was observed, corresponding to a rotation of ~10E-4 rad. The implementation of a time-dependent correction on the alignment by using the laser system data led to sizeable improvements on the ALEPH data…
A large-area Silicon Drift Detectors (SDDs) system has been developed by the SIDDHARTA2 collaboration for high precision light kaonic atoms X-ray spectroscopy at the DAΦNE collider of Istituto Nazionale di Fisica Nucleare - Laboratori Nazionali di Frascati. The SDDs geometry and electric field configuration, combined with their read-out electronics, make these devices suitable to perform high precision light kaonic atoms spectroscopy measurements in the high background of the DAΦNE collider. This work presents the spectroscopic response of the SDDs system during the kaonic helium first exotic …
The CDF experiment's Silicon Vertex Trigger is a system of 150 custom 9U VME boards that reconstructs axial tracks in the CDF silicon strip detector in a 15 microsecond pipeline. SVT's 35 micron impact parameter resolution enables CDF's Level 2 trigger to distinguish primary and secondary particles, and hence to collect large samples of hadronic bottom and charm decays. We review some of SVT's key design features. Speed is achieved with custom VLSI pattern recognition, linearized track fitting, pipelining, and parallel processing. Testing and reliability are aided by built-in logic state analy…
The Belle II experiment, which is situated at the interaction point of the SuperKEKB $e^+e^{-}$ collider at KEK, Tsukuba, Japan, is expected to collect data corresponding to an integrated luminosity of 50~ab$^{- 1}$. This data set will be sensitive to beyond-the-standard-model physics via precision measurements and searches for very rare decays. At its heart lies a six-layer vertex detector consisting of two layers of pixel detectors (PXD) and four layers of double-sided silicon microstrip detectors (SVD). Precise vertexing as provided by this device is essential for measurements of time-depen…
The BABAR Silicon Vertex Tracker (SVT) is a five-layer double-sided silicon detector designed to provide precise measurements of the position and direction of primary tracks, and to fully reconstruct low-momentum tracks produced in e+e- collisions at the PEP-II asymmetric collider at Stanford Linear Accelerator Center. This paper describes the design, implementation, performance, and validation of the local alignment procedure used to determine the relative positions and orientations of the 340 SVT wafers. This procedure uses a tuned mix of in-situ experimental data and complementary lab-bench…
The physics program of high energy e+e- linear colliders relies on the accurate identification of fermions to study in details the profile of the Higgs boson, search for new particles and later probe the multi-TeV mass region by direct searches and precision electro-weak measurements. This paper reviews the requirements, conceptual design and sensor R&D for the Vertex Tracker.
The Linear Collider TPC collaboration constructed a Large Prototype TPC (LPTPC) which is now installed at the EUDET facility, in DESY. The SiLC-collaboration (Silicon for the Linear Collider) will install position sensitive silicon strip sensors outside the field cage of the LPTPC, to provide precise tracking information. The data acquisition system (DAQ) is an adapted CMS readout system. The silicon modules are tested and ready to be installed, the mechanical module support and the DAQ system are in preparation.
High precision physics at future colliders requires unprecedented highly granular calorimeters for the application of the Particle Flow (PF) algorithm. The physical proof of concept was given in the previous campaign of beam tests of physic prototypes within the CALICE collaboration. We present here the latest beam and laboratory test results and R&D developments for the Silicon-Tungsten Electromagnetic Calorimeter technological prototype with fully embedded very front-end (VFE) electronics for the International Large Detector at the International Linear Collider project.
The radiation hardness of the AToM chips of the BaBar Silicon Vertex Tracker has been investigated by means of irradiations with photons from a 60Co source and 0.9 GeV electrons. The increase in noise and the decrease in gain of the amplifier have been measured as a function of the applied capacitive load and the absorbed dose. Different beam intensities have been used to study the effect of different dose rates to the AToM radiation damage. The chip digital functionalities have been tested up to a dose of 5.5 Mrads for the 60Co photons and 9 Mrads for the 0.9 GeV electrons. In addition a pede…
Over the past few years we have developed, in collaboration with the SARNOFF Corporation, a design of a Monolithic CMOS Pixel Detector for ILC Vertex Detectors. The unique feature of this design is that each hit is accompanied by a time tag with sufficient precision to assign each hit to a particular bunch crossing of the ILC (thus the name Chronopixel). This reduces the occupancy even in the innermost Vertex Detector layer to negligible levels, allowing a robust Vertex Detector even in the case that the backgrounds in the ILC are higher than presently estimated.
Conformal tracking is an innovative and comprehensive pattern recognition technique using a cellular automaton-based track finding performed in a conformally-mapped space. It is particularly well-suited for light-weight silicon systems with high position resolution, such as the next generation of tracking detectors designed for future electron-positron colliders. The algorithm has been developed and validated with simulated data of the CLICdet tracker. It has demonstrated not only excellent performance in terms of tracking efficiency, fake rate and track parameters resolution but also robustne…
The Belle II experiment at the SuperKEKB collider in Japan is designed to indirectly probe new physics using approximately 50 times the data recorded by its predecessor. An accurate determination of the decay-point position of subatomic particles such as beauty and charm hadrons as well as a precise measurement of low-momentum charged particles will play a key role in this pursuit. These will be accomplished by an inner tracking device comprising two layers of pixelated silicon detector and four layers of silicon vertex detector based on double-sided microstrip sensors. We describe herein the …
A silicon-based fine granularity calorimeter is a potential technology for the future International Linear Collider ILC, the future circular collider CEPC, and is also the chosen technology for the upgraded CMS experiment of the Large Hadron Collider. Active silicon sensing pads are used as MIP counters and the standard calibration of the calorimeter uses weights based on the average energy loss, $dEdx$. In this work, the limitations of the dEdx calibration method in terms of energy linearity, scale and resolution are explored. In the case of a calorimeter with varying passive layer thickness …
For the new hadron collider LHC and some of its updates in luminosity and energy, as SLHC and VLHC, the silicon detectors could represent an important option, especially for the tracking system and calorimetry. The main goal of this paper is to analyse the expected long-time degradation in the bulk of the silicon as material and for silicon detectors, in continuous radiation field, in these hostile conditions. The behaviour of silicon in relation to various scenarios for upgrade in energy and luminosity is discussed in the frame a phenomenological model developed previously by the authors. Dif…
The physics aims at the proposed high-energy $e^+e^-$ collider CLIC pose challenging demands on the performance of the detector system. Precise hit-time tagging, an excellent spatial resolutions, and a low mass are required for the vertex and tracking detectors. To meet these requirements, an all-silicon vertex and tracking detector system is foreseen, for which a broad R&D programme on a variety of novel silicon detector technologies is being pursued. For the ultra-low mass vertex detector, different hybrid technologies with innovative sensor concepts and interconnection techniques are explor…
The SiLC - Silicon for the Linear Collider - collaboration aims to develop silicon detector technology for tracking in the international linear collider experiments. The R & D programme involves a substantial effort in simulation of the response of detector designs. In this contribution, an overview of ongoing efforts in this area is given.
The physics aims at the proposed future high-energy linear $e^+e^-$ collider CLIC pose challenging demands on the performance of the detector system. In particular, the vertex and tracking detectors have to combine a spatial resolution of a few micrometres and a low material budget with a time-stamping accuracy of a few nanoseconds. For the vertex detector, fine-pitch sensors, dedicated 65nm readout ASICs, fine-pitch bonding techniques using solder bumps or anisotropic conductive films as well as monolithic devices based on Silicon-On-Insulator technology are explored. Fully monolithic CMOS se…
The Silicon Vertex Detector of Belle II is a state-of-the-art tracking and vertexing system based on double-sided silicon strip sensors, designed and fabricated by a large international collaboration in the period 2012--2018. Since 2019 it has been in operation providing high quality data with a small number of defective channels (<1%), a large hit-finding efficiency (>99%), a good signal-to-noise ratio (well in excess of 10 for all sensor configurations and tracks). Together with the good control over the alignment, these are all essential factors to achieve good tracking reconstruction and p…
Several future high-energy physics facilities are currently being planned. The proposed projects include high energy $e^+ e^-$ circular and linear colliders, hadron colliders and muon colliders, while the Electron-Ion Collider (EIC) has already been approved for construction at the Brookhaven National Laboratory. Each proposal has its own advantages and disadvantages in term of readiness, cost, schedule and physics reach, and each proposal requires the design and production of specific new detectors. This paper first presents the performances required to the future silicon tracking systems at …
This paper presents a study of vertex tracking with a beam hodoscope consisting of three layers of monolithic pixel sensors in SOI technology on high-resistivity substrate. We study the track extrapolation accuracy, two-track separation and vertex reconstruction accuracy in pion-Cu interactions with 150 and 300 GeV/c pions at the CERN SPS. Results are discussed in the context of vertex tracking at future lepton colliders.
Using the simulation framework of the SiD detector to study the Higgs -> mumu decay channel showed a considerable gain in signal significance could be achieved through an increase in charged particle momentum resolution. However more detailed simulations of theZ -> mumu decay channel demonstrated that significant improvement in the resolution could not be achieved through an increase in tracker granularity. Conversely detector stability studies into missing/dead vertex layers using longer lived particles displayed an increase in track resolution. The existing 9.15 cm x 25 μm silicon strip geom…
The Silicon Vertex Detector (SVD), with its four double-sided silicon strip sensor layers, is one of the two vertex sub-detectors of Belle II operating at SuperKEKB collider (KEK, Japan). Since 2019 and the start of the data taking, the SVD has demonstrated a reliable and highly efficient operation, even running in an environment with harsh beam backgrounds that are induced by the world's highest instantaneous luminosity. In order to provide the best quality track reconstruction with an efficient pattern recognition and track fit, and to correctly propagate the uncertainty on the hit's positio…
The extreme radiation dose received by vertex detectors at the Large Hadron Collider dictates stringent requirements on their cooling systems. To be robust against radiation damage, sensors should be maintained below -20 degree C and at the same time, the considerable heat load generated in the readout chips and the sensors must be removed. Evaporative CO2 cooling using microchannels etched in a silicon plane in thermal contact with the readout chips is an attractive option. In this paper, we present the first results of microchannel prototypes with circulating, two-phase CO2 and compare them …
Silicon radiation detectors are an integral component of current and planned collider experiments in high energy physics. Simulations of these detectors are essential for deciding operational configurations, for performing precise data analysis, and for developing future detectors. In this white paper, we briefly review the existing tools and discuss challenges for the future that will require research and development to be able to cope with the foreseen extreme radiation environments of the High Luminosity runs of the Large Hadron Collider and future hadron colliders like FCC-hh and SPPC.
Thin planar silicon sensors with a pitch of 55um, active edge and various guard ring layouts are investigated, using two-dimensional finite-element T-CAD simulations. The simulation results have been compared to experimental data, and an overall good agreement is observed. It is demonstrated that 50um thin planar silicon sensors with active edge with floating guard ring or without guard ring can be operated fully efficiently up to the physical edge of the sensor. The simulation findings are used to identify suitable sensor designs for application in the high-precision vertex detector of the fu…
Primary vertex finding for collider experiments is studied. The efficiency and precision of finding interaction vertices can be improved by advanced clustering and classification methods, such as agglomerative clustering with fast pairwise nearest neighbor search, followed by Gaussian mixture model or k-means clustering.
The Collider Detector at Fermilab (CDF) pursues a broad physics program at Fermilab's Tevatron collider. Between Run II commissioning in early 2001 and the end of operations in September 2011, the Tevatron delivered 12 fb-1 of integrated luminosity of p-pbar collisions at sqrt(s)=1.96 TeV. Many physics analyses undertaken by CDF require heavy flavor tagging with large charged particle tracking acceptance. To realize these goals, in 2001 CDF installed eight layers of silicon microstrip detectors around its interaction region. These detectors were designed for 2--5 years of operation, radiation …
The successful running of the large area Silicon trackers of ATLAS and CMS at LHC, and the ongoing R&D for the upgrade of these tracking systems, in various stages, over this decade, are a full proof of this technology and of its still impressive potential. The Linear Collider project is waiting for the possible discovery of a light Higgs at LHC maybe by end of 2012. These facts opened a new phase for the R&D on Silicon tracking for the Linear Collider, with enhanced synergy with LHC, Astrophysics and other HEP experiments, thus leading to new perspectives and alternatives.
We report on progress in the development of the LSTFE2 prototype front-end ASIC geared towards the readout of silicon microstrip sensors in a Linear Collider detector. We also discuss progress in the design of the back-end digital architecture for this readout scheme.
The future Electron-Ion Collider (EIC) will utilize a series of high-luminosity high-energy electron+proton ($e+p$) and electron+nucleus ($e+A$) collisions to explore the inner structure of nucleon and nucleus and the matter formation process. Heavy flavor hadron and jet measurements at the EIC will play an essential role in determining the nucleon/nucleus parton distribution function and heavy quark hadronization process in not well constrained kinematic regions. A high granularity and low material budget forward silicon tracker will enable precise forward heavy flavor measurements at the EIC…
An upgraded asymmetric e+e- flavor factory, SuperKEKB, is planned at KEK. It will deliver a luminosity of 8 x 10^35 cm^-2 s^-1, allowing precision measurements in the flavor sector which can probe new physics well beyond the scales accessible to direct observation. The increased luminosity also requires upgrades of the Belle detector. Of critical importance here is a new silicon pixel vertex tracker, which will significantly improve the decay vertex resolution. This new detector will consist of two detector layers close to the interaction point, using DEPFET pixel sensors with 50 um thick sili…
High-Resolution Timing for Vertex-Reconstructed Muon-Spin Spectroscopy Using Plastic Scintillators and MuTRiG
Kirchhoff Institute for Physics, Heidelberg University（海德堡大学基尔霍夫物理研究所）；Institute for Nuclear Physics, Johannes Gutenberg-Universität Mainz（约翰内斯·古腾堡美因茨大学核物理研究所）；PSI Center for Neutron and Muon Sciences（瑞士保罗谢勒研究所中子与μ子科学中心）；Institute for Particle Physics and Astrophysics, ETH Zürich（苏黎世联邦理工学院粒子物理与天体物理研究所）；Physics Institute, Heidelberg University（海德堡大学物理研究所）
Between Run II commissioning in early 2001 and the end of operations in September 2011, the Tevatron collider delivered 12~fb$^{-1}$ of $p\bar{p}$ collisions at $\sqrt{s}=1.96$ TeV to the Collider Detector at Fermilab (CDF). During that time, the CDF silicon vertex detector was subject to radiation doses of up to 12 Mrad. After the end of operations, the silicon detector was annealed for 24 days at $18^{\circ}$C. In this paper, we present a measurement of the change in the bias currents for a subset of sensors during the annealing period. We also introduce a novel method for monitoring the dep…
Silicon pad sensors are proposed as active material in highly granular sampling calorimeters of future collider experiments such as the Compact Linear Collider (CLIC) or the International Linear Collider (ILC). The electromagnetic section of these designs often include O(1000 m$^2$) of silicon pad sensors. For the luminosity measurement, a dedicated forward calorimeter called LumiCal is foreseen. More recently, the CMS experiment has decided to adopt the same concept in its endcap calorimeter upgrade for the HL-LHC. The sensors are typically produced from 6- or 8-inch wafers and consist of a f…
Silicon pad sensors with novel functions of higher timing resolution (LGAD: Low Gain Avalanche Detector) and higher position resolution (PSD: Position Sensitive Detector) are studied for an application to Silicon-Tungsten electromagnetic calorimeter for a detector of the International Linear Collider (ILC). Prototype sensors are fabricated, equipped with dedicated ASICs (Application-Specific Integrated Circuits) and tested with a positron beam as well as a radioisotope. The first results of the measurements of timing resolution with LGADs and position reconstruction with PSDs are reported.
The D0 Run II silicon microstrip tracker (SMT) has 3 square meters of Si area. There are 792,576 channels read out by 6192 SVXIIe chips on 912 read out modules. The SMT provides track and vertex reconstruction capabilities over the full pseudorapidity coverage of the D0 detector. The full detector has been running successfully since April 2002. This presentation covers the experience in commissioning and operating, the recent electronics upgrade which improved stability of the SMT and estimates of the radiation damage.
Since the start of data taking in spring 2019 at the SuperKEKB collider (KEK, Japan) the Belle II Silicon Vertex Detector (SVD) has been operating reliably and with high efficiency, while providing high quality data: high signal-to-noise ratio, greater than 99% hit efficiency, and precise spatial resolution. These attributes, combined with stability over time, result in good tracking efficiency. Currently the occupancy, dominated by beam-background hits, is quite low (about 0.5% in the innermost layer), causing no problems to the SVD data reconstruction. In view of the operation at higher lumi…
In 2019 the Belle II experiment started data taking at the asymmetric SuperKEKB collider (KEK, Japan) operating at the Y(4S) resonance. Belle II will search for new physics beyond the Standard Model by collecting an integrated luminosity of 50~ab$^{-1}$. The silicon vertex detector (SVD), consisting of four layers of double-sided silicon strip sensors, is one of the two vertex sub-detectors. The SVD extrapolates the tracks to the inner pixel detector (PXD) with enough precision to correctly identify hits in the PXD belonging to the track. In addition the SVD has standalone tracking capability …
The CALICE collaboration develops prototypes for highly granular calorimeters for detectors at a future linear electron positron collider. The highly granular electromagnetic calorimeter prototype was tested in particle beams. We present the study of the interactions of hadrons in this prototype.
The LHCb Vertex Locator contains 42 silicon sensor modules. Each module has two silicon sensors. A method for determining the relative alignment of the silicon sensors within each module from data is presented. The software implementation details are discussed. Monte-Carlo simulation studies are described that demonstrate an alignment precision of 1.3 micron is obtained in the sensor plane.
Silicon detectors for the Roman Pots of the large hadron collider TOTEM experiment aim for full sensitivity at the edge where a terminating structure is required for electrical stability. This work provides an innovative approach reducing the conventional width of the terminating structure to less than 100 microns, still using standard planar fabrication technology. The objective of this new development is to decouple the electric behaviour of the surface from the sensitive volume within tens of microns. The explanation of the basic principle of this new approach together with the experimental…
With an active silicon area of more than 200 squaremetres, the silicon strip tracker of the CMS experiment, one of the experiments currently under construction for the future Large Hadron Collider at CERN, will be by far the largest silicon tracker in the world. Efficient mass production and rigid quality control are crucial to finish the detector, comprising of more than 15000 silicon strip modules, in time with optimal quality. After excellent performance of substructures has been proven in various test beam experiments, integration of the active detector elements into the mechanical support…
Letter of intent describing SiD (Silicon Detector) for consideration by the International Linear Collider IDAG panel. This detector concept is founded on the use of silicon detectors for vertexing, tracking, and electromagnetic calorimetry. The detector has been cost-optimized as a general-purpose detector for a 500 GeV electron-positron linear collider.
The Linear Collider Flavour Identification (LCFI) collaboration studies CCD detectors for quark flavour identification in the framework of a future linear e+e- collider. The flavour identification is based on precision reconstruction of charged tracks very close to the interaction point. Therefore, this detector will be exposed to a high level of radiation and thus an important aspect of the vertex detector development are radiation hardness studies. Results of detailed simulations of the charged transport properties of a CCD prototype chip are reported and compared with initial measurements. …
We summarize the R&D activities on a novel semitransparent microstrip sensor to be used on laser-based alignment systems for silicon trackers. The new sensor is used both for particle tracking and laser detection. The aim of this research line is to increase the optical transmittance (T) of Silicon microstrips detectors to infrared light, introducing minor modifications to the sensor design still suitable for its industrial production. The optical simulations used in the sensor design have been experimentally validated against several patterned material samples. This activities have been carri…
The R&D Collaboration SiLC (Silicon tracking for Linear Colliders) is based on generic R&D aiming to develop the next generation of large Silicon tracking systems for the Linear collider experiments; it serves all three ILC detector concepts. There is a strong involvement in ILD, a natural collaboration with SiD and recent 4th concept interest to use Silicon tracking technology as well. Here is a very brief summary of the latest results on sensors, Front End Electronics, Mechanics and Integration issues, test bench and test beam results and where to go from there.
Fine pixel CCD (FPCCD) is one of the candidate sensor technologies for the vertex detector used for experiments at the International Linear Collider (ILC). A vertex detector system for the International Large Detector (ILD) using FPCCD sensors has been designed. We report on the R&D status of FPCCD sensors, as well as the vertex detector design for ILD.
In order to extend the tracking acceptance, to improve the primary and secondary vertex reconstruction and thus enhancing the tagging capabilities for short lived particles, the ZEUS experiment at the HERA Collider at DESY installed a silicon strip vertex detector. The barrel part of the detector is a 63 cm long cylinder with silicon sensors arranged around an elliptical beampipe. The forward part consists of four circular shaped disks. In total just over 200k channels are read out using $2.9 {\rm m^2}$ of silicon. In this report a detailed overview of the design and construction of the detect…
We propose an algorithm, deployable on a highly-parallelized graph computing architecture, to perform rapid reconstruction of charged-particle trajectories in the high energy collisions at the Large Hadron Collider and future colliders. We use software emulation to show that the algorithm can achieve an efficiency in excess of 99.95% for reconstruction with good accuracy. The algorithm can be implemented on silicon-based integrated circuits using field-programmable gate array technology. Our approach can enable a fast trigger for massive charged particles that decay invisibly in the tracking v…
The discovery of a Higgs boson by the experiments at the LHC marks a major breakthrough in particle physics, with far-reaching consequences for our understanding of the fundamental principles of our Universe. To fully explore this unique particle, experiments at high-energy electron-positron colliders are being planned, providing substantial added benefit over the capabilities of the LHC alone, such as model-independent measurements of couplings, constraints on invisible decays and precise measurements of the self-coupling. This contribution summarizes the Higgs physics program at such future …
