Test-beam characterisation of the CLICTD technology demonstrator - a small collection electrode High-Resistivity CMOS pixel sensor with simultaneous time and energy measurement
R. Ballabriga, E. Buschmann, M. Campbell, D. Dannheim, K. Dort, N. Egidos, L. Huth, I. Kremastiotis, J. Kröger, L. Linssen, X. Llopart, M. Munker, A. Nürnberg, … 展开作者
R. Ballabriga, E. Buschmann, M. Campbell, D. Dannheim, K. Dort, N. Egidos, L. Huth, I. Kremastiotis, J. Kröger, L. Linssen, X. Llopart, M. Munker, A. Nürnberg, W. Snoeys, S. Spannagel, T. Vanat, M. Vicente, M. Williams
The CLIC Tracker Detector (CLICTD) is a monolithic pixel sensor. It is fabricated in a 180 nm CMOS imaging process, modified with an additional deep low-dose n-type implant to obtain full lateral depletion. The sensor features a small collection diode, which is essential for achieving a low input capacitance. The CLICTD sensor was designed as a technology demonstrator in the context of the tracking detector studies for the Compact Linear Collider (CLIC). Its design characteristics are of broad interest beyond CLIC, for HL-LHC tracking detector upgrades. It is produced in two different pixel flavours: one with a continuous deep n-type implant, and one with a segmented n-type implant to ensure fast charge collection. The pixel matrix consists of $16\times128$ detection channels measuring $300 \times 30$ microns. Each detection channel is segmented into eight sub-pixels to reduce the amount of digital circuity while maintaining a small collection electrode pitch. This paper presents the characterisation results of the CLICTD sendor in a particle beam. The different pixel flavours are compared in detail by using the simultaneous time-over-threshold and time-of-arrival measurement functionalities. Most notably, a time resolution down to $(5.8 \pm 0.1)$ ns and a spatial resolution down to $(4.6 \pm 0.2)$ microns are measured. The hit detection efficiency is found to be well above 99.7% for thresholds of the order of several hundred electrons.
The CLIC Tracker Detector (CLICTD) is a monolithic pixel sensor featuring pixels of 30um x 37.5um and a small collection diode. The sensor is fabricated in a 180 nm CMOS imaging process, using two different pixel flavours: the first with a continuous n-type implant for full lateral depletion, and the second with a segmentation in the n-type implant for accelerated charge collection. Moreover, CLICTD features an innovative sub-pixel segmentation scheme that allows the digital footprint to be reduced while maintaining a small sub-pixel pitch. In this contribution, test-beam measurements for the …
CLICTD is a monolithic silicon pixel sensor fabricated in a modified 180 nm CMOS imaging process with a small collection electrode design and a high-resistivity epitaxial layer. It features an innovative sub-pixel segmentation scheme and is optimised for fast charge collection and high spatial resolution. The sensor was developed to target the requirements for the tracking detector of the proposed future Compact Linear Collider (CLIC). Most notably, a temporal resolution of a few nanoseconds and a spatial resolution below 7 microns are demanded. In this contribution, the sensor performance mea…
The CLIC Tracker Detector (CLICTD) is a monolithic pixelated sensor chip produced in a $180$ nm imaging CMOS process built on a high-resistivity epitaxial layer. The chip, designed in the context of the CLIC tracking detector study, comprises a matrix of ${16\times128}$ elongated pixels, each measuring ${300\times30}$ $μ$m$^2$. To ensure prompt charge collection, every elongated pixel is segmented in eight sub-pixels, each containing a collection diode and a separate analog front-end. A simultaneous $8$-bit time measurement with $10$ ns time bins and $5$-bit energy measurement with programmabl…
Small collection-electrode monolithic CMOS sensors profit from a high signal-to-noise ratio and a small power consumption, but have a limited active sensor volume due to the fabrication process based on thin high-resistivity epitaxial layers. In this paper, the active sensor depth is investigated in the monolithic small collection-electrode technology demonstrator CLICTD. Charged particle beams are used to study the charge-collection properties and the performance of devices with different thicknesses both for perpendicular and inclined particle incidence. In CMOS sensors with a high-resistivi…
The Belle II barrel region is instrumented with the Time of Propagation (TOP) particle identification system based on sixteen fused-silica bars arranged around the interaction point acting as Cherenkov radiator. Due to the mechanical design of the TOP system these quartz bars do not overlap, but leave a gap of around 2cm between them. This leads to around 6% of all tracks in the nominal TOP acceptance region to escape without traversing any of the quartz bars and thus not giving any usable particle identification information from the TOP system and an additional 3% of tracks being degraded due…
Within the EUDET consortium a high resolution pixel beam telescope is being developed. The telescope consists of up to six planes of monolithic active pixel sensors. A flexible data acquisition environment is available for the telescope and the system is equipped with all the required infrastructure. Since the first installation of a demonstrator telescope in 2007, it has been extensively tested and used by various detector R&D groups. The results of test beam measurements are described here, demonstrating the telescope performance.
High Energy Particle Physics experiments at the LHC use hybrid silicon detectors, in both pixel and strip geometry, for their inner trackers. These detectors have proven to be very reliable and performant. Nevertheless, there is great interest in the development of depleted CMOS silicon detectors, which could achieve similar performances at lower cost of production and complexity. We present recent developments of this technology in the framework of the ATLAS CMOS demonstrator project. In particular, studies of two active sensors from LFoundry, CCPD_LF and LFCPIX, and the first fully monolithi…
Deep sub micron HV-CMOS processes offer the opportunity for sensors built by industry standard techniques while being HV tolerant, making them good candidates for drift-based, fast collecting, thus radiation-hard pixel detectors. For the upgrade of the ATLAS Pixel Detector towards the HL-LHC requirements, active pixel sensors in HV-CMOS technology were investigated. These implement amplifier and discriminator stages directly in insulating deep n-wells, which also act as collecting electrodes. The deep n-wells allow for bias voltages up to 150V leading to a depletion depth of several 10um. Prot…
An upgrade of the ATLAS experiment for the High Luminosity phase of LHC is planned for 2024 and foresees the replacement of the present Inner Detector (ID) with a new Inner Tracker (ITk) completely made of silicon devices. Depleted active pixel sensors built with the High Voltage CMOS (HV-CMOS) technology are investigated as an option to cover large areas in the outermost layers of the pixel detector and are especially interesting for the development of monolithic devices which will reduce the production costs and the material budget with respect to the present hybrid assemblies. For this purp…
Time-of-flight measurement is an important advancement in PET scanners to improve image reconstruction with a lower delivered radiation dose. This article describes the monolithic ASIC for the TT-PET project, a novel idea for a high-precision PET scanner for small animals. The chip uses a SiGe Bi-CMOS process for timing measurements, integrating a fully-depleted pixel matrix with a low-power BJT-based front-end per channel, integrated on the same 100 $μ m$ thick die. The target timing resolution is 30 ps RMS for electrons from the conversion of 511 keV photons. A novel synchronization scheme u…
Monolithic active pixel sensors produced in High Voltage CMOS (HV-CMOS) technology are being considered for High Energy Physics applications due to the ease of production and the reduced costs. Such technology is especially appealing when large areas to be covered and material budget are concerned. This is the case of the outermost pixel layers of the future ATLAS tracking detector for the HL-LHC. For experiments at hadron colliders, radiation hardness is a key requirement which is not fulfilled by standard CMOS sensor designs that collect charge by diffusion. This issue has been addressed by …
The physics aims at the proposed high-energy $e^+e^-$ collider CLIC pose challenging demands on the performance of the detector system. Precise hit-time tagging, an excellent spatial resolutions, and a low mass are required for the vertex and tracking detectors. To meet these requirements, an all-silicon vertex and tracking detector system is foreseen, for which a broad R&D programme on a variety of novel silicon detector technologies is being pursued. For the ultra-low mass vertex detector, different hybrid technologies with innovative sensor concepts and interconnection techniques are explor…
In the context of the studies of the ATLAS High Luminosity LHC programme, radiation tolerant pixel detectors in CMOS technologies are investigated. To evaluate the effects of substrate resistivity on CMOS sensor performance, the H35DEMO demonstrator, containing different diode and amplifier designs, was produced in ams H35 HV-CMOS technology using four different substrate resistivities spanning from $\mathrm{80}$ to $\mathrm{1000~Ω\cdot cm}$. A glueing process using a high-precision flip-chip machine was developed in order to capacitively couple the sensors to FE-I4 Readout ASIC using a thin l…
In September 2008 the Slim5 collaboration submitted a low material budget silicon demonstrator to test with 12 GeV/c protons, at the PS-T9 test-beam at CERN. Inside the reference telescope, two different detectors were placed as device under test (DUT). The first was a 4k-Pixel Matrix of Deep N Well MAPS, developed in a 130 nm CMOS Technology, providing digital sparsified readout. The other one was a high resistivity double sided silicon detector, with short strips at 45-degree angle to the detector's edge, read out by the FSSR2 chip. The FSSR2 is a 128 channel data-driven fast readout chip de…
The CYGNO experiment: a gaseous TPC with optical readout for rare events searches
University of Coimbra（科英布拉大学）；Gran Sasso Science Institute（格兰萨索科学研究所）；Laboratori Nazionali del Gran Sasso（格兰萨索国家实验室）；Laboratori Nazionali di Frascati（弗拉斯卡蒂国家实验室）；University of Sheffield（谢菲尔德大学）
The MALTA family of Depleted Monolithic Active Pixel Sensor (DMAPS) produced in Tower 180 nm CMOS technology targets radiation hard applications for the HL-LHC and beyond. Several process modifications and front-end improvements have resulted in radiation hardness up to $2 \times 10^{15}~1~\text{MeV}~\text{n}_{eq}/\text{cm}^2$ and time resolution below 2 ns, with uniform charge collection efficiency across the Pixel of size $36.4 \times 36.4~μ\text{m}^2$ with a $3~μ\text{m}^2$ electrode size. The MALTA2 demonstrator produced in 2021 on high-resistivity epitaxial silicon and on Czochralski subs…
