The recent discovery of high thermoelectric performance in Mg$_3$Sb$_2$ has been critically enabled by the success in $n$-type doping of this material, which is achieved under Mg-rich growth conditions, typically with chalcogens (Se, Te) as extrinsic dopants. Using first-principles defect calculations, we previously predicted that higher electron concentrations ($\sim10^{20}$ cm$^{-3}$) can be achieved in Mg$_3$Sb$_2$ by doping with La instead of Se or Te. Subsequent experiments showed that free electron concentration in La-doped Mg$_3$Sb$_{2-x}$Bi$_x$ indeed exceeds those in the Te-doped material. Herein, we further investigate $n$-type doping of Mg$_3$Sb$_2$ and predict that, in addition to La, other group-3 elements (Sc, Y) are also effective as $n$-type dopants; Y is as good as La while Sc slightly less. Overall, we find that doping with any group-3 elements should lead to higher free electron concentrations than doping with chalcogens.
The p-type doping efficiency of 4H silicon carbide (4H-SiC) is rather low due to the large ionization energies of p-type dopants. Such an issue impedes the exploration of the full advantage of 4H-SiC for semiconductor devices. In this letter, we show that co-doping group-IVB elements effectively decreases the ionization energy of the most widely used p-type dopant, i. e., aluminum (Al), through the Coulomb repulsion between the energy levels of group-IVB elements and that of Al in 4H-SiC. Among group-IVB elements Ti has the most prominent effectiveness. Ti decreases the ionization energy of Al…
Despite the lack of reproducible experimental confirmation, group-V elements have been considered as possible sources of p-type doping in ZnO in the form of simple and complex defects. Using ab initio calculations, based on state-of-the-art hybrid exchange-correlation functional, we study a wide range of defects and defect complexes related with N, P, As, and Sb impurities. We show that none of the candidates for p-type doping can be considered a good source of holes in the valence band due to deep acceptor levels and low formation energies of compensating donor defects. In addition, we discus…
A new doping mechanism is described, whereby a doping impurity does not simply transfer charge to the bands of a host semiconductor or semimetal, but rearranges the core energy levels deep in the valence band of the host. This, in turn, leads to a redistribution of all electrons in the host, and, if designed properly, changes the location of the Fermi level EF and the density of conducting charge carriers near EF. The principle is proven experimentally in elemental Bi, whereby group III elements In and Ga dope Bi p-type, in spite of the fact that all three atoms are trivalent in the solid stat…
Thermoelectric performance of SnTe has been found to enhance with isovalent doping of alkaline and transition metal elements where most of these elements have solubility of less than 13%. We propose a strategy of doping rare earth element Yb to enhance the thermoelectric performance of SnTe. With heavy atomic mass and strong spin-orbit coupling, even the mild doping of Yb (~ 5%) is enough to create a degeneracy via band-convergence which enhances the density of states near Fermi level and improve overall performance. Our transport data and first-principles calculations corroborate that nearly …
Our density functional theory calculations for Fe_{13-n}M_{n} for M = Sc, Ti, V, Cr, Mn, Co, Ni, and Cu up to n = 4 show that the icosahedral symmetry of Fe13, albeit minor changes in bond lengths, is robust despite doping and is retained for all homotops of Mn, Co, Ni and Cu. Based on analysis of density of states of the doped cluster, adsorption of carbon atom, and adhesion energies for fragments of single walled carbon nanotubes, we propose a core-shell type structure with a central Mn atom surrounded by Fe surface shell atoms as the most favorable doped nanocatalyst for SWCNT nucleation an…
Topological semimetals (TSs) are promising candidates for low-power spin-orbit torque (SOT) devices due to their large charge-to-spin conversion efficiency. Here, we investigated the charge-to-spin conversion efficiency of amorphous PtSn4 (5 nm)/CoFeB (2.5-12.5 nm) layered structures prepared by a magnetron sputtering method at room temperature. The charge-to-spin ratio of PtSn4/CoFeB bilayers was 0.08, characterized by a spin torque ferromagnetic resonance (ST-FMR) technique. This ratio can further increase to 0.14 by inducing dopants, like Al and CoSi, into PtSn4. The dopants can also decrea…
Historically, the discovery and optimization of doped bulk materials has been predominantly developed through an Edisonian approach. While successful and despite the constant progress in fundamental understanding of detector materials physics, the process has been restricted by its inherent slow pace and low success rate. This poor throughput owes largely to the considerable compositional space that needs to be accounted for to fully comprehend complex material/performance relationship. Here, we present a combinatorial approach where doped bulk scintillator materials can be rapidly optimized f…
We investigated the influence of doping antiferromagnetic MnN in polycrystalline MnN/CoFe exchange bias systems, showing high exchange bias of up to 1800 Oe at room temperature. The thermal stability of those systems is limited by nitrogen diffusion that occurs during annealing processes. In order to improve the thermal stability, defect energies of elements throughout the periodic table substituting Mn were calculated via density functional theory. Elements calculated to have negative defect energies bind nitrogen stronger to the lattice and could be able to prevent diffusion. We prepared exc…
In this paper, structural and electronic properties and stability of (10, 0) born nitride nanotube (BNNT) are considered within density functional theory by doping group IV elements of the periodic table. The HOMO-LUMO gap has been strongly modified and treated a dual manner by choosing B or N sites for dopant atoms. Formation energy calculation shows that B site doping is more stable than N site doping. Results also show that all dopants turn the pristine BNNT into a p-type semiconductor except for carbon-doped BNNT at B site.
We have explored, computationally and experimentally, the magnetic properties of \fecob{} alloys. Calculations provide a good agreement with experiment in terms of the saturation magnetization and the magnetocrystalline anisotropy energy with some difficulty in describing Co$_2$B, for which it is found that both full potential effects and electron correlations treated within dynamical mean field theory are of importance for a correct description. The material exhibits a uniaxial magnetic anisotropy for a range of cobalt concentrations between $x=0.1$ and $x=0.5$. A simple model for the tempera…
New electrode materials for alkaline-ion batteries are a timely topic. Among many promising candidates, V2O5 is one of the most interesting cathode materials. While having very high theoretical capacity, in practice, its performance is hindered by low stability and poor conductivity. As regards theoretical descriptions of V2O5, common DFT-GGA calculations fail to reproduce both the electronic and crystal structure. While the band gap is underestimated, the interlayer spacing is overestimated as weak dispersion interactions are not properly described within GGA. Here we show that the combinatio…
Over the last few years, group IV hexagonal-diamond type crystals have acquired great attention in semiconductor physics thanks to the appearance of novel and very effective growth methods. However, many questions remain unaddressed on their extrinsic doping capability and on how it compares to those of diamond-like structures. This point is here investigated through numerical simulations conducted in the framework of the Density Functional Theory (DFT). The comparative analysis for group III and V dopant atoms shows that: i) in diamond-type crystals the bulk sites symmetry ($T_d$) is preserve…
We have investigated the transport and magnetic properties of group-IV ferromagnetic semiconductor Ge1-xFex films (x = 1.0 and 2.3 %) with and without boron doping grown by molecular beam epitaxy (MBE). In order to accurately measure the transport properties of 100-nm-thick Ge1-xFex films, (001)-oriented silicon-on-insulator (SOI) wafers with an ultra-thin Si body layer (~5 nm) were used as substrates. Owing to the low Fe content, the hole concentration and mobility in the Ge1-xFex films were exactly estimated by Hall measurements because the anomalous Hall effect in these films was found to b…
Single dopings of Mn and Fe in Si are investigated using 8-, 64-, and 216-atom supercells and a first-principles method based on density functional theory. Between the two transition metal elements (TMEs), atom sizes play an essential role in determining the contraction or the expansion of neighboring atoms around the TME dopant at a substitutional site. At a tetrahedral interstitial site, there is only expansion. Magnetic moments/TME at the two sites are calculated. Physical origins for these inter-related properties are discussed. A few suggestions about the growth of these Si-based alloys a…
The power factor of pure p-type ZnSb has been calculated via ab initio simulations assuming that the carrier concentrations are due to the doping effect of intrinsic zinc vacancies. With a vacancy concentration close to the experimental solubility limit we were able to perfectly reproduce the Power Factor measured in polycrystalline ZnSb samples. The methodology has then been successfully extended for predicting the effect of extrinsic doping elements on the thermoelectric properties of ZnSb. Germanium and tin seem to be promising p-type doping elements. In addition, we give, for the first tim…
Due to its unique physical and chemical properties, graphene is being considered as a promising material for energy conversion and storage applications. Introduction of functional groups and dopants on/in graphene is a useful strategy for tuning its properties. In order to fully exploit its potential, atomic-level understanding of its interaction with species of importance for such applications is required. We present a DFT study of the interaction of sodium atoms with epoxy-graphene and analyze how this interaction is affected upon doping with boron and nitrogen. We demonstrate how the dopant…
Stanene is a quantum spin hall insulator and a promising material for electronic and optoelectronic devices. Density functional theory (DFT) calculations are performed to study the band gap opening in stanene by elemental mono- (B, N) and co-doping (B-N). Different patterned B-N co-doping is studied to change the electronic properties in stanene. A patterned B-N co-doping opens the band gap in stanene and the semiconducting nature persists with strain. Molecular dynamics (MD) simulations are performed to confirm the thermal stability of such doped system. The stress-strain study indicates that…
We systematically calculate the structure, formation enthalpy, formation free energy, elastic constants and electronic structure of Ti$_{0.98}$X$_{0.02}$ system by density functional theory (DFT) simulations to explore the effect of transition metal X (X=Ag, Cd, Co, Cr, Cu, Fe, Mn, Mo, Nb, Ni, Pd, Rh, Ru, Tc, and Zn) on the stability mechanism of $β$-titanium. Based on our calculations, the results of formation enthalpy and free energy show that adding trace X is beneficial to the thermodynamic stability of $β$-titanium. This behavior is well explained by the density of state (DOS). However, t…
We investigate the role of transition metal atoms of group V-b (V, Nb, and Ta) and VI-b (Cr, Mo, and W) as n- or p-type dopants in anatase TiO2 using thermodynamic principles and density functional theory with the Heyd-Scuseria-Ernzerhof HSE06 hybrid functional. The HSE06 functional provides a realistic value for the band gap, which ensures a correct classification of dopants as shallow or deep donors or acceptors. Defect formation energies and thermodynamic transition levels are calculated taking into account the constraints imposed by the stability of TiO2 and the solubility limit of the imp…
Motivated by a recent theoretical suggestion that doping electrons into various CaAl$_2$Si$_2$-type Zintl phase compounds may give rise to high thermoelectric performance, we explore the possibility of n-type (electron carrier) doping of CaZn$_2X_2$ ($X$ = As, P) using first principles calculation. We consider n-type doping of CaZn$_2X_2$ with the following two situations: interstitial-site doping of alkaline earth metals $AE$ (= Mg, Ca, Sr, Ba) and group 3 elements $G3$ (= Sc, Y, La), and $G3$ substitutional doping for the Ca site. The evaluation of the formation energy of these defects in va…
Dopability in semiconductors plays a crucial role in device performance. Using the first-principles density-functional theory calculations, we investigate systematically the doping properties of layered MX2 (M= Mo, W; X=S, Te) by replacing M or X with the groups III, V and VII elements. It is found that the defect BM is hard to form in MX2 due to the large formation energy originating from the crystal distortion, while AlM is easy to realize compared to the former. In MoS2, WS2 and MoTe2, Al is the most desirable p-type dopant under anion-rich conditions among the group III components, since A…
We investigate the spin-orbit coupling (SOC) effects on the electronic structures and semi-classic transport coefficients of half-Heusler $\mathrm{ANiB}$ (A=Ti, Hf, Sc, Y; B=Sn, Sb, Bi) by using generalized gradient approximation (GGA). Calculated results show that SOC splits the valence bands at high symmetry $Γ$ point, and modifies the outline of $Γ$-centered valence bands, which has remarkable effects on the electron transport properties. Thermoelectric properties are performed through solving Boltzmann transport equations within the constant scattering time approximation. It is found that …
We report on the on-surface synthesis of 7 armchair graphene nanoribbons (7-AGNRs) substituted with nitrile (CN) functional groups. The CN groups are attached to the GNR backbone by modifying the 7-AGNR precursor. While many of these groups survive the on-surface synthesis, the reaction process causes the cleavage of some CN from the ribbon backbone and the on-surface cycloisomerization of few nitriles onto pyridine rings. Scanning Tunneling Spectroscopy and Density Functional Theory reveal that CN groups behave as very efficient n-dopants, significantly downshifting the bands of the ribbon, a…
Recent theoretical and experimental evaluations demonstrated that KLi6TaO6 is a good Li-ion conductor. In this study, the energetics and detailed mechanism of Li-ion migration, relevant to the point defects of KLi6TaO6, were analyzed by first-principles calculations. Defect formation energy analysis suggested that it has limited chemical potential conditions for attaining Li-excess conditions through doping (substituting tetravalent elements for Ta). The formation of other native defects, such as Li vacancies, hinders the stabilization of the dopant and compensates for the interstitial Li. Whe…
Doping mobile carriers into ordinary semiconductors such as Si, GaAs, and ZnO was the enabling step in the electronic and optoelectronic revolutions. The recent emergence of a class of "Quantum Materials", where uniquely quantum interactions between the components produce specific behaviors such as topological insulation, unusual magnetism, superconductivity, spin-orbit-induced and magnetically-induced spin splitting, polaron formation, and transparency of electrical conductors, pointed attention to a range of doping-related phenomena associated with chemical classes that differ from the tradi…
Structural degeneracies underpin the ferroic behavior of next-generation two-dimensional materials, and lead to peculiar two-dimensional structural transformations under external fields, charge doping and/or temperature. The most direct indicator of the ease of these transformations is an {\em elastic energy barrier}, defined as the energy difference between the (degenerate) structural ground state unit cell, and a unit cell with an increased structural symmetry. Proximity of a two-dimensional material to a bulk substrate can affect the magnitude of the critical fields and/or temperature at wh…
SnSe, a group IV-VI monochalcogenide with layered crystal structure similar to black phosphorus, has recently attracted extensive interests due to its excellent thermoelectric properties and potential device applications. Experimental electronic structure of both the valence and conduction bands is critical for understanding the effects of hole versus electron doping on the thermoelectric properties, and to further reveal possible change of the band gap upon doping. Here, we report the multivalley valence bands with a large effective mass on semiconducting SnSe crystals and reveal single-valle…
Co-doping of Ce-doped LaBr$_3$ with Ba, Ca, or Sr improves the energy resolution that can be achieved by radiation detectors based on these materials. Here, we present a mechanism that rationalizes of this enhancement that on the basis of first principles electronic structure calculations and point defect thermodynamics. It is shown that incorporation of Sr creates neutral $V_\text{Br}$-Sr$_\text{La}$ complexes that can temporarily trap electrons. As a result, Auger quenching of free carriers is reduced, allowing for a more linear, albeit slower, scintillation light yield response. Experimenta…
The mechanisms underlying the enhancement of magnetic anisotropies (MAs) of Sm ions, owing to valence electrons at the Sm site and the screened nuclear charges of ligands, are clarified using a detailed analysis of crystal fields (CF). In order to investigate the finite-temperature magnetic properties, we developed an effective spin model for SmFe$_{12}X$ ($X$=H, B, C, and N) and SmFe$_{11}M$ ($M$=Ti, V, and Co), where the magnetic moments, CF parameters, and exchange fields were determined by first-principle calculations. Using this model, the MA constants and magnetization curves at finite t…
Fluorite CeO$_2$ doped with group IV elements is studied within the DFT and DFT+U framework. Concentration dependent formation energies are calculated for Ce$_{1-x}$Z$_x$O$_2$ (Z= C, Si, Ge, Sn, Pb, Ti, Zr, Hf) with $0\leq x \leq 0.25$ and a roughly decreasing trend with ionic radius is observed. The influence of the valence and near valence electronic configuration is discussed, indicating the importance of filled $d$ and $f$ shells near the Fermi level for all properties investigated. A clearly different behavior of group IVa and IVb dopants is observed: the former are more suitable for surf…
The band gap engineering of group IV semiconductors has not been well explored theoretically and experimentally, except for SiGe. Recently, GeSn has attracted much attention due to the possibility of obtaining a direct band gap in this alloy, thereby making it suitable for light emitters. Other group IV alloys may also potentially exhibit material properties useful for device applications, expanding the space for band gap engineering in group IV. In this work the electronic band structure of all group IV semiconductor alloys is investigated. Twelve possible A:B alloys, where A is a semiconduct…
We report a combined theoretical and experimental search for thermoelectric materials based on semiconducting zinc antimony. Influence of three new doping elements (sodium, potassium and boron) on the electronic properties is investigated as well as the carrier concentration and temperature dependence of the thermoelectric coefficients obtained through density-functional calculations and Boltzmann transport theory. Distortion of the electron arrangement caused by the doping elements is displayed as a deformation charge density around the atoms. Based on the band structures, the density of stat…
In this work, we study the effect of doping the Rutile-type dioxide SnO2 material by the non-metal Sulfur (S) atoms on the electronic properties. In fact, we have used the ab-initio method applied on the basis of the Density Functional Theory (DFT) using the Quantum Espresso code. Through the density of states and the band structure calculations for different concentrations have been deduced. When doping the SnO2 material with 6% of Sulfur (S), we found a perfect symmetry between up and down spin states in the total DOS confirming the non-magnetic behavior of this material doped SnO2 with 6% o…
We study the effect of electron doping on the bonding character and stability of two-dimensional (2D) structures of elemental boron, called borophene, which is known to form many stable allotropes. Our {\em ab initio} calculations for the neutral system reveal previously unknown stable 2D $ε$-B and $ω$-B structures. We find that the chemical bonding characteristic in this and other boron structures is strongly affected by extra charge. Beyond a critical degree of electron doping, the most stable allotrope changes from $ε$-B to a buckled honeycomb structure. Additional electron doping, mimickin…
Two-dimensional (2D) materials may have potential applications in thermoelectric devices. In this work, we systematically investigate the thermoelectric properties of orthorhombic group IV-VI monolayers $\mathrm{AB}$ (A=Ge and Sn; B=S and Se) by the first-principles calculations and semiclassical Boltzmann transport theory. The spin-orbit coupling (SOC) is included to investigate their electronic transport, which produces observable effects on power factor, especially for n-type doping. According to calculated $ZT$, the four monolayers exhibit diverse anisotropic thermoelectric properties, alt…
We study the effect of surface adsorption of 27 different adatoms on the electronic and magnetic properties of monolayer black phosphorus using density functional theory. Choosing a few representative elements from each group, ranging from alkali metals (group I) to halogens (group VII), we calculate the band structure, density of states, magnetic moment and effective mass for the energetically most stable location of the adatom on monolayer phosphorene. We predict that group I metals (Li, Na, K), and group III adatoms (Al, Ga, In) are effective in enhancing the n-type mobile carrier density, …
Doping lithium-ion battery electrode materials LiMO$_2$ (M = Co, Ni, Mn) with impurities has been shown to be an effective way to optimize their electrochemical properties. Here, we report a detailed first-principles study of layered oxides LiCoO$_2$, LiNiO$_2$, and LiMnO$_2$ lightly doped with transition-metal (Fe, Co, Ni, Mn) and non-transition-metal (Mg, Al) impurities using hybrid-density-functional defect calculations. We find that the lattice site preference is dependent on both the dopant's charge and spin states, which are coupled strongly to the local lattice environment and can be af…
Bi$_2$Se$_3$, a layered three dimensional (3D) material, exhibits topological insulating properties due to presence of surface states and a band gap of 0.3 eV in the bulk. We study the effect hydrostatic pressure $P$ and doping with rare earth elements on the topological aspect of this material in bulk from a first principles perspective. Our study shows that under a moderate pressure of P$>$7.9 GPa, the bulk electronic properties show a transition from an insulating to a Weyl semi-metal state due to band inversion. This electronic topological transition may be correlated to a structural chang…
High-speed electrical switching of Ge2Sb2Te5 (GST) remains a challenging task due to the large impedance mismatch between the low-conductivity amorphous state and the high-conductivity crystalline state. In this letter, we demonstrate an effective doping scheme using nickel to reduce the resistivity contrast between the amorphous and crystalline states by nearly three orders of magnitude. Most importantly, our results show that doping produces the desired electrical performance without adversely affecting the film's optical properties. The nickel doping level is approximately 2% and the lattic…
$Li_{2}RuO_{3}$ with a honeycomb structure undergoes a drastic transition from a regular honeycomb lattice with the $C2/m$ space group to a valence bond solid state of the $P2_{1}/m$ space group with an extremely strong dimerization at 550 K. We synthesized $Li_{2}Ru_{1-x}Mn_{x}O_{3}$ with a full solid solution and investigated doping effects on the valence bond solid state as a function of Mn content. The valence bond solid state is found to be stable up to $x = 0.2$, based on our extensive experiments: structural studies, resistivity, and magnetic susceptibility. On the other hand, the exten…
We report the effect of carbon doping in Ti-stabilized nonstoichiometric molybdenum diboride (Mo$_{0.96}$Ti$_{0.04}$)$_{0.8}$B$_{2}$, which exhibits bulk superconductivity below $T_{\rm c}$ = 7.0 K. It is found that (Mo$_{0.96}$Ti$_{0.04}$)$_{0.8}$(B$_{1-x}$C$_{x}$)$_{2}$ maintains the AlB$_{2}$-type phase with a uniform elemental distribution for $x$ = 0.12 and 0.16. The substitution of carbon for boron leads to a slight increase in $a$-axis, a remarkable reduction in $c$-axis, the formation of planar defects along the (100) crystallographic planes, and a shift of the B 1$s$ peaks towards hig…
