Van der Waals (vdW) heterojunctions composed of 2-dimensional (2D) layered materials are emerging as a solid-state materials family that exhibit novel physics phenomena that can power high performance electronic and photonic applications. Here, we present the first demonstration of an important building block in vdW solids: room temperature (RT) Esaki tunnel diodes. The Esaki diodes were realized in vdW heterostructures made of black phosphorus (BP) and tin diselenide (SnSe2), two layered semiconductors that possess a broken-gap energy band offset. The presence of a thin insulating barrier between BP and SnSe2 enabled the observation of a prominent negative differential resistance (NDR) region in the forward-bias current-voltage characteristics, with a peak to valley ratio of 1.8 at 300 K and 2.8 at 80 K. A weak temperature dependence of the NDR indicates electron tunneling being the dominant transport mechanism, and a theoretical model shows excellent agreement with the experimental results. Furthermore, the broken-gap band alignment is confirmed by the junction photoresponse and the phosphorus double planes in a single layer of BP are resolved in transmission electron microscopy (TEM) for the first time. Our results represent a significant advance in the fundamental understanding of vdW heterojunctions, and widen the potential applications base of 2D layered materials.
We demonstrate electrical electron spin injection via interband tunneling in ferromagnetic/nonmagnetic semiconductor Esaki diodes. An interband tunnel junction between ferromagnetic p+-(Ga,Mn)As and nonmagnetic n+-GaAs under reverse-bias allows spin-polarized tunneling of electrons from the valence band of (Ga,Mn)As to the conduction band of n+-GaAs. The spin polarization of tunneled electrons is probed by circular polarization of electroluminescence (EL) from an n-GaAs/InGaAs/p-GaAs light emitting structure integrated with the diode. Clear hysteresis loop with +-6.5% remanence is observed in …
We report on measurements of direct spin Hall effect in a lightly n-doped GaAs channel. As spin detecting contacts we employed highly efficient ferromagnetic Fe/(Ga,Mn)As/GaAs Esaki diode structures. We investigate bias and temperature dependence of the measured spin Hall signal and evaluate the value of total spin Hall conductivity and its dependence on channel conductivity and temperature. From the results we determine skew scattering and side jump contribution to the total spin hall conductivity and compare it with the results of experiments on higher conductive n-GaAs channels[Phys. Rev. L…
We report on a local spin valve effect observed unambiguously in lateral all-semiconductor all-electrical spin injection devices, employing p+-(Ga,Mn)As/n+-GaAs Esaki diode structures as spin aligning contacts. We discuss the observed local spin-valve signal as a result of interplay between spin-transport-related contribution and tunneling anisotropic magnetoresistance of magnetic contacts. The magnitude of the spin-related magnetoresistance change is equal to 30 Ohm which is twice the magnitude of the measured non-local signal.
We report here on anisotropy of spin polarization obtained in lateral all-semiconductor all-electrical spin injection devices, employing $p^{+}-$(Ga,Mn)As/$n^{+}-$GaAs Esaki diode structures as spin aligning contacts, resulting from the dependence of the efficiency of spin tunneling on the orientation of spins with respect to different crystallographic directions. We observed an in-plane anisotropy of $~8%$ in case of spins oriented either along $[1\bar{1}0]$ or $[110]$ directions and $~25%$ anisotropy between in-plane and perpendicular-to-plane orientation of spins.
We investigate the correlation between spin signals measured in three-terminal (3T) geometry by the Hanle effect and the spin accumulation generated in a semiconductor channel in a lateral (Ga,Mn)As/GaAs Esaki diode device. We systematically compare measurements using a 3T configuration, probing spin accumulation directly beneath the injecting contact, with results from nonlocal measurements, where solely spin accumulation in the GaAs channel is probed. We find that the spin signal detected in the 3T configuration is dominated by a bias-dependent spin detection sensitivity, which in turn is st…
The p-n junction diode and field-effect transistor (FET) are the two most ubiquitous building blocks of modern electronics and optoelectronics. In recent years, the emergence of reduced dimensionality materials has suggested that these components can be scaled down to atomic thicknesses. Although high performance field-effect devices have been achieved from monolayered materials and their heterostructures, a p-n heterojunction diode derived from ultrathin materials is notably absent and constrains the fabrication of complex electronic and optoelectronic circuits. Here, we demonstrate a gate-tu…
We report novel graphene nanoribbon (GNR)/semiconductor nanowire (SNW) heterojunction light-emitting diodes (LEDs) for the first time. The GNR and SNW have a face-to-face contact structure, which has the merit of bigger active region. ZnO, CdS, and CdSe NWs were employed in our case. At forward biases, the GNR/SNW heterjunction LEDs could emit light with wavelengths varying from ultraviolet (380 nm) to green (513 nm) to red (705 nm), which were determined by the band-gaps of the involved SNWs. The mechanism of light emitting for the GNR/SNW heterojunction LED was discussed. Our approach can ea…
By the insertion of thin InGaN layers into Nitrogen-polar GaN p-n junctions, polarization-induced Zener tunnel junctions are studied. The reverse-bias interband Zener tunneling current is found to be weakly temperature dependent, as opposed to the strongly temperature-dependent forward bias current. This indicates tunneling as the primary reverse-bias current transport mechanism. The Indium composition in the InGaN layer is systematically varied to demonstrate the increase in the interband tunneling current. Comparing the experimentally measured tunneling currents to a model helps identify the…
Heterojunctions between three-dimensional (3D) semiconductors with different bandgaps are the basis of modern light-emitting diodes, diode lasers, and high-speed transistors. Creating analogous heterojunctions between different two-dimensional (2D) semiconductors would enable band engineering within the 2D plane and open up new realms in materials science, device physics and engineering. Here we demonstrate that seamless high-quality in-plane heterojunctions can be grown between the 2D monolayer semiconductors MoSe2 and WSe2. The junctions, grown by lateral hetero-epitaxy using physical vapor …
The electrical and photodiode characteristics of ensemble and single p-GaN nanowire and n-Si heterojunction devices were studied. Ideality factor of the single nanowire p-GaN/n-Si device was found to be about three times lower compared to that of the ensemble nanowire device. Apart from the deep-level traps in p-GaN nanowires, defect states due to inhomogeneity in Mg dopants in the ensemble nanowire device are attributed to the origin of high ideality factor. Photovoltaic mode of ensemble nanowire device showed an improvement in the fill-factors up to 60 percent over the single nanowire device…
The fabrication, initial structural characterization and diode measurements are reported for the first boron carbide / silicon carbide heterojunction diode. Current-voltage curves obtained for operation at temperatures from 24 C to 388 C. PECVD-deposited undoped boron carbide material is highly crystalline and consists of a variety of polytypes of B-C with crystal sizes as large as 110 nm. Crystal phases are similar to those for PECVD B-C on Si but only partially match known boron and boron-rich B-C phases.
A general self-aligned fabrication scheme is reported here for a diverse class of electronic devices based on van der Waals materials and heterojunctions. In particular, self-alignment enables the fabrication of source-gated transistors in monolayer MoS2 with near-ideal current saturation characteristics and channel lengths down to 135 nm. Furthermore, self-alignment of van der Waals p-n heterojunction diodes achieves complete electrostatic control of both the p-type and n-type constituent semiconductors in a dual-gated geometry, resulting in gate-tunable mean and variance of anti-ambipolar Ga…
$β$-Ga${_2}$O${_3}$ based semiconductor devices are expected to have significantly improved high-power and high-temperature performance due to its ultra-wide bandgap of close to 5 eV. However, the high-temperature operation of these ultra-wide-bandgap devices is usually limited by the relatively low 1-2 eV built-in potential at the Schottky barrier with most high-work-function metals. Here, we report heterojunction p-NiO/n-$β$-Ga${_2}$O${_3}$ diodes fabrication and optimization for high-temperature device applications, demonstrating a current rectification ratio of more than 10${^6}$ at 410°C.…
Electrical and optical characterization of two-dimensional/three-dimensional (2D/3D) p-molybdenum disulfide/n-gallium nitride (p-MoS2/n-GaN) heterojunction diodes are reported. Devices were fabricated on high-quality, large-area p-MoS2 grown by chemical vapor deposition (CVD) on hexagonal sapphire substrates. The processed devices were transferred onto GaN/sapphire substrates, and the transferred films were characterized by X-ray diffraction (XRD) and atomic force microscopy (AFM). On-axis XRD spectra and surface topology obtained from AFM scans were consistent with previously grown high-quali…
Recently demonstrated metal-semiconductor heterojunctions with few-atom thickness show their promise as 2D Schottky contacts for future integrated circuits and nanoelectronics. The theory for 3D Schottky contacts, however, fails on these low-dimensional systems. Here, we propose a new model that yields carrier distribution and potential profile across the 2D metal-semiconductor heterojunction under the equilibrium condition, based on the input from first-principle calculations. Our calculation also suggests that, at the same forward bias, the current density of a stack of 2D graphene-phosphore…
Wide and ultra-wide band gap semiconductors can provide excellent performance due to their high energy band gap, which leads to breakdown electric fields that are more than an order of magnitude higher than conventional silicon electronics. In materials where p-type doping is not available, achieving this high breakdown field in a vertical diode or transistor is very challenging. We propose and demonstrate the use of dielectric heterojunctions that use extreme permittivity materials to achieve high breakdown field in a unipolar device. We demonstrate the integration of a high permittivity mate…
Computational design of NDR tunnel diodes with high peak-to-valley current ratio based on two-dimensional cold metals: The case of NbSi$_2$N$_4$/HfSi$_2$N$_4$/NbSi$_2$N$_4$ lateral heterojunction diode
The growth and electrical characterization of a heterojunction formed between 2D layered p-MoS2 and nitrogen-doped 4H-SiC is reported. Direct growth of p-type MoS2 films on SiC was demonstrated using chemical vapor deposition, and the MoS2 films were found to be crystalline based on x-ray diffraction measurements. The resulting heterojunction was found to display rectification and current-voltage characteristics consistent with a p-n junction diode. Capacitance voltage measurements were used to determine the built-in voltage for the p-MoS2/n-SiC heterojunction p-n diode. The demonstration of h…
Significant efficiency droop is a major concern for light-emitting diodes and laser diodes operating at high current density. Recent study has suggested that heavily Bi-alloyed GaAs can decrease the non-radiative Auger recombination and therefore alleviate the efficiency droop. Using density functional theory, we studied a newly fabricated quaternary alloy, GaAs1-x-yPyBix, which can host significant amounts of Bi, through calculations of its band gap, spin-orbit splitting, and band offsets with GaAs. We found that the band gap changes of GaAs1-x-yPyBix relative to GaAs are determined mainly by…
The changes of defect characteristics induced by accelerated lifetime tests on the heterostructure n-ZnO/i-ZnO/CdS/Cu(In, Ga)(S, Se)$_2$/Mo relevant for photovoltaic energy conversion are investigated. We subject heterojunction and Schottky devices to extended damp heat exposure at 85$^{\circ}$C ambient temperature and 85% relative humidity for various time periods. In order to understand the origin of the pronounced changes of the devices, we apply current--voltage and capacitance--voltage measurements, admittance spectroscopy, and deep-level transient spectroscopy. The fill factor and open-c…
Since the discovery of its photovoltaic properties organometallic salt CH$_3$NH$_3$PbI$_3$ became the subject of vivid interest. The material exhibits high light conversion efficiency, it lases in red color, and it can serve as the basis for light emitting diodes and photodetectors. Here we report another surprising feature of this material family, the photo-tunability of the diode response of a heterojunction made of CH$_3$NH$_3$PbI$_3$ and its close relative, CH$_3$NH$_3$SnI$_3$. In the dark state the device behaves as a diode, with the Sn homologue acting as the "p" side. The junction is ex…
Backward diodes conduct more efficiently in the reverse bias than in the forward bias, providing superior high frequency response, temperature stability, radiation hardness, and 1/f noise performance than a conventional diode conducting in the forward direction. Here we demonstrate a van der Waals material based backward diode by exploiting the giant staggered band offsets of WSe2/SnSe2 vertical heterojunction. The diode exhibits an ultra-high reverse rectification ratio (R) of ~2.1x10^4 and the same is maintained up to an unusually large bias of 1.5 V - outperforming existing backward diode r…
Layered two-dimensional (2-D) semiconductors can be combined with other low-dimensional semiconductors to form non-planar mixed-dimensional van der Waals (vdW) heterojunctions whose charge transport behavior is influenced by the heterojunction geometry, providing a new degree of freedom to engineer device functions. Towards that end, we investigated the photoresponse of Si nanowire/MoS2 heterojunction diodes with scanning photocurrent microscopy and time-resolved photocurrent measurements. Comparison of n-Si/MoS2 isotype heterojunctions with p-Si/MoS2 heterojunction diodes under varying biases…
In this paper we consider the essential electronic excited states in parallel chains of semiconducting polymers that are currently being explored for photovoltaic and light-emitting diode applications. In particular, we focus upon various type II donor-acceptor heterojunctions and explore the relation between the exciton binding energy to the band off-set in determining the device characteristic of a particular type II heterojunction material. As a general rule, when the exciton binding energy is greater than the band off-set at the heterojunction, the exciton will remain the lowest energy exc…
High-Temperature Hydrogen Sensors Based on Gallium Oxide Heterojunction Diodes
Materials Science Center, National Laboratory of the Rockies（国家落基山实验室材料科学中心）；Department of Metallurgical and Materials Engineering, Colorado School of Mines（科罗拉多矿业学院冶金与材料工程系）
We investigate a vertically-stacked hybrid photodiode consisting of a thin n-type molybdenum disulfide (MoS$_{2}$) layer transferred onto p-type silicon. The fabrication is scalable as the MoS$_{2}$ is grown by a controlled and tunable vapor phase sulfurization process. The obtained large-scale p-n heterojunction diodes exhibit notable photoconductivity which can be tuned by modifying the thickness of the MoS$_{2}$ layer. The diodes have a broad spectral response due to direct and indirect band transitions of the nanoscale MoS$_{2}$. Further, we observe a blue-shift of the spectral response in…
van der Waals (vdW) heterojunctions formed by two-dimensional (2D) materials have attracted tremendous attention due to their excellent electrical/optical properties and device applications. However, current 2D heterojunctions are largely limited to atomic crystals, and hybrid organic/inorganic structures are rarely explored. Here, we fabricate hybrid 2D heterostructures with p-type dioctylbenzothienobenzothiophene (C8-BTBT) and n-type MoS2. We find that few-layer C8-BTBT molecular crystals can be grown on monolayer MoS2 by vdW epitaxy, with pristine interface and controllable thickness down t…
Band alignment of grafted diamond/GaN p-n heterojunctions interfaced with ALD Al2O3 and SiNx/Al2O3
University of Wisconsin-Madison（威斯康星大学麦迪逊分校）；Texas A&M University（德克萨斯农工大学）；University at Buffalo, The State University of New York（纽约州立大学布法罗分校）；Fraunhofer USA Inc（弗劳恩霍夫美国公司）；Northrop Grumman Corporation（诺斯罗普·格鲁曼公司）
InAs/GaSb and similar materials systems have generated great interest as a heterojunction for tunnel field effect transistors (TFETs) due to favorable band alignment. However, little is currently understood about how such TFETs are affected by materials defects and nonidealities. We present measurements of the conductance slope for various InAs/GaSb heterojunctions via two-terminal electrical measurements, which removes three-terminal parasitics and enables direct study on the effect of microstructure on tunnelling. Using this, we can predict how subthreshold swings in TFETs can depend on micr…
The recently emerged organohalide perovskites (e.g., CH3NH3PbI3) have drawn intense attention for high efficiency solar cells. However, with a considerable solubility in many solvents, these perovskites are not typically compatible with conventional lithography processes for more complicated device fabrications that are important for both fundamental studies and technological applications. Here we report the creation of novel heterojunction devices based on perovskites and two-dimensional (2D) crystals by taking advantage of the layered characteristic of lead iodide (PbI2) and vapor phase inte…
A ferroelectric junction transistor memory made from switchable van der Waals p-n heterojunctions
Zhejiang University（浙江大学）；King Abdullah University of Science and Technology（阿卜杜拉国王科技大学）；Wenzhou University（温州大学）；Chinese Academy of Sciences（中国科学院）；South China Normal University（华南师范大学）；Xidian University（西安电子科技大学）
We have successfully demonstrated Si/GaAs p-n heterostructures using Al2O3 ultra-thin oxide interfacial layers. The band diagram and band offsets were investigated using X-ray photoelectron spectroscopy and confirm a small discontinuity in the conduction band (0.03 eV) at the interface. The interface defect density (Dit) values of the heterointerface with different ultra-thin oxide (UO) thicknesses ranged from 0.35 nm to 3.5 nm and were also characterized based on a metal-oxide-semiconductor capacitor (MOSCAP) structure using a capacitance-voltage measurement. The results revealed that a thin …
Nanoscaled room-temperature ferroelectricity is ideal for developing advanced non-volatile high-density memories. However, reaching the thin film limit in conventional ferroelectrics is a long-standing challenge due to the possible critical thickness effect. Van der Waals materials, thanks to their stable layered structure, saturate interfacial chemistry and weak interlayer couplings, are promising for exploring ultra-thin two-dimensional (2D) ferroelectrics and device applications. Here, we demonstrate a switchable room-temperature ferroelectric diode built upon a 2D ferroelectric α-In2Se3 la…
Mid-infrared LEDs based on lattice-mismatched hybrid IV-VI/III-V heterojunctions
Stanford University（斯坦福大学）；CREOL, The College of Optics and Photonics, University of Central Florida（中佛罗里达大学光学与光子学学院CREOL）；Department of Materials Science and Engineering, University of Central Florida（中佛罗里达大学材料科学与工程系）
Disentangling Measurement Protocol from Material Physics in Isotypic and Anisotypic SiC/Si Heterojunctions: A Metrology-Driven Study for Betavoltaic Energy Conversion
β-Ga2O3-Based Heterojunctions: Exploring Growth Orientations and Alloying on Electronic Properties
School of Mathematics and Physics, Queen’s University Belfast（贝尔法斯特女王大学数学与物理学院）；Tyndall National Institute, University College Cork（科克大学丁达尔国家研究所）；European Theoretical Spectroscopy Facility（欧洲理论光谱设施）
Large spin splitting in the conduction band (CB) and valence band (VB) of ferromagnetic semiconductors (FMSs), predicted by the influential mean-field Zener model[1,2] and assumed in many spintronic device proposals[3-8], has never been observed in the mainstream p-type Mn-doped FMSs[9-15]. Here using tunnelling spectroscopy in Esaki-diode structures, we report the observation of such a large spontaneous spin-splitting energy (ΔE = 31.7 - 50 meV) in the CB bottom of n-type FMS (In,Fe)As, which is surprising considering the very weak s-d exchange interaction reported in several zinc-blende (ZB)…
The nitride semiconductor materials GaN, AlN, and InN, and their alloys and heterostructures have been investigated extensively in the last 3 decades, leading to several technologically successful photonic and electronic devices. Just over the past few years, a number of new nitride materials have emerged with exciting photonic, electronic, and magnetic properties. Some examples are 2D and layered hBN and the III-V diamond analog cBN, the transition metal nitrides ScN, YN, and their alloys (e.g. ferroelectric ScAlN), piezomagnetic GaMnN, ferrimagnetic Mn4N, and epitaxial superconductor/semicon…
The vertical stacking of van der Waals (vdW) materials introduces a new degree of freedom to the research of two-dimensional (2D) systems. The interlayer coupling strongly influences the band structure of the heterostructures, resulting in novel properties that can be utilized for electronic and optoelectronic applications. Based on microwave microscopy studies, we report quantitative electrical imaging on gated molybdenum disulfide (MoS2)/tungsten diselenide (WSe2) heterostructure devices, which exhibit an intriguing anti-ambipolar effect in the transfer characteristics. Interestingly, in the…
