We report here on anisotropy of spin polarization obtained in lateral all-semiconductor all-electrical spin injection devices, employing $p^{+}-$(Ga,Mn)As/$n^{+}-$GaAs Esaki diode structures as spin aligning contacts, resulting from the dependence of the efficiency of spin tunneling on the orientation of spins with respect to different crystallographic directions. We observed an in-plane anisotropy of $~8%$ in case of spins oriented either along $[1\bar{1}0]$ or $[110]$ directions and $~25%$ anisotropy between in-plane and perpendicular-to-plane orientation of spins.
We report on a local spin valve effect observed unambiguously in lateral all-semiconductor all-electrical spin injection devices, employing p+-(Ga,Mn)As/n+-GaAs Esaki diode structures as spin aligning contacts. We discuss the observed local spin-valve signal as a result of interplay between spin-transport-related contribution and tunneling anisotropic magnetoresistance of magnetic contacts. The magnitude of the spin-related magnetoresistance change is equal to 30 Ohm which is twice the magnitude of the measured non-local signal.
We investigate the correlation between spin signals measured in three-terminal (3T) geometry by the Hanle effect and the spin accumulation generated in a semiconductor channel in a lateral (Ga,Mn)As/GaAs Esaki diode device. We systematically compare measurements using a 3T configuration, probing spin accumulation directly beneath the injecting contact, with results from nonlocal measurements, where solely spin accumulation in the GaAs channel is probed. We find that the spin signal detected in the 3T configuration is dominated by a bias-dependent spin detection sensitivity, which in turn is st…
We investigated the influence of n+-GaAs thickness and doping density of GaMnAs/n+-GaAs Esaki tunnel junction on the efficiency of the electrical electron spin injection. We prepared seven samples of GaMnAs/n+-GaAs tunnel junctions with different n+-GaAs thickness and doping density grown on identical p-AlGaAs/p-GaAs/n-AlGaAs light emitting diode (LED) structures. Electroluminescence (EL) polarization of the surface emission was measured under the Faraday configuration with external magnetic field. All samples have the bias dependence of the EL polarization, and higher EL polarization is obtai…
We demonstrate electrical electron spin injection via interband tunneling in ferromagnetic/nonmagnetic semiconductor Esaki diodes. An interband tunnel junction between ferromagnetic p+-(Ga,Mn)As and nonmagnetic n+-GaAs under reverse-bias allows spin-polarized tunneling of electrons from the valence band of (Ga,Mn)As to the conduction band of n+-GaAs. The spin polarization of tunneled electrons is probed by circular polarization of electroluminescence (EL) from an n-GaAs/InGaAs/p-GaAs light emitting structure integrated with the diode. Clear hysteresis loop with +-6.5% remanence is observed in …
We report on measurements of direct spin Hall effect in a lightly n-doped GaAs channel. As spin detecting contacts we employed highly efficient ferromagnetic Fe/(Ga,Mn)As/GaAs Esaki diode structures. We investigate bias and temperature dependence of the measured spin Hall signal and evaluate the value of total spin Hall conductivity and its dependence on channel conductivity and temperature. From the results we determine skew scattering and side jump contribution to the total spin hall conductivity and compare it with the results of experiments on higher conductive n-GaAs channels[Phys. Rev. L…
Van der Waals (vdW) heterojunctions composed of 2-dimensional (2D) layered materials are emerging as a solid-state materials family that exhibit novel physics phenomena that can power high performance electronic and photonic applications. Here, we present the first demonstration of an important building block in vdW solids: room temperature (RT) Esaki tunnel diodes. The Esaki diodes were realized in vdW heterostructures made of black phosphorus (BP) and tin diselenide (SnSe2), two layered semiconductors that possess a broken-gap energy band offset. The presence of a thin insulating barrier bet…
Electrical injection and detection of spin-polarized electrons is demonstrated for the first time in a single wafer, all-semiconductor, GaAs-based lateral spintronic device, employing p+-(Ga,Mn)As/n+-GaAs ferromagnetic Esaki diodes as spin aligning contacts. The conversion of spin-polarized holes into spin-polarized electrons via Esaki tunnelling leaves its mark in a bias dependence of the spin-injection efficiency, which at maximum reaches the relatively high value of 50%.
Significant efficiency droop is a major concern for light-emitting diodes and laser diodes operating at high current density. Recent study has suggested that heavily Bi-alloyed GaAs can decrease the non-radiative Auger recombination and therefore alleviate the efficiency droop. Using density functional theory, we studied a newly fabricated quaternary alloy, GaAs1-x-yPyBix, which can host significant amounts of Bi, through calculations of its band gap, spin-orbit splitting, and band offsets with GaAs. We found that the band gap changes of GaAs1-x-yPyBix relative to GaAs are determined mainly by…
We present experimental evidence and physics-based simulations of the lock-on effect in high-voltage GaAs avalanche diodes. The avalanche triggering is initiated by steep voltage ramp applied to the diode and in-series 50 Ohm load. After subnanosecond avalanche switching the reversely biased GaAs diode remains in the conducting state for the whole duration of the applied pulse (dozens of nanoseconds). There is no indication of the p-n junction recovery that is commonly expected to develop on the nanosecond scale due to the drift extraction of non-equilibrium carriers. The diode voltage keeps a…
Passivation of the GaAs surface was attempted using aqueous P2S5-NH4OH,(NH4)2Sx and plasma nitrogenataion and hydrogenation. Results indicate that plasma nitrogenation with pretreatment of plasma hydrogenation produced consistent reduction in reverse leakage current at room-temperature for all p and n type schottky diodes. Some diodes showed an order of magnitude improvement in current density. Aqueous passivation showed similarly an improvement however, additional experimentation is required into long term stability and the arsenic-sulphur covalent bond strength.
We demonstrate the formation of semimetal graphite/semiconductor Schottky barriers where the semiconductor is either silicon (Si), gallium arsenide (GaAs) or 4H-silicon carbide (4H-SiC). Near room temperature, the forward-bias diode characteristics are well described by thermionic emission, and the extracted barrier heights, which are confirmed by capacitance voltage measurements, roughly follow the Schottky-Mott relation. Since the outermost layer of the graphite electrode is a single graphene sheet, we expect that graphene/semiconductor barriers will manifest similar behavior.
We describe a new means for electrically creating spin polarization in semiconductors. In contrast to spin injection of electrons by tunneling through a reverse-biased Schottky barrier, we observe spin accumulation at the metal/semiconductor interface of forward-biased ferromagnetic Schottky diodes, which is consistent with a theory of spin-dependent reflection off the interface. Spatiotemporal Kerr microscopy is used to image the electron spin and the resulting dynamic nuclear polarization that arises from the non equilibrium carrier polarization.
We report on efficient spin injection in p-doped InGaAs/GaAs quantum-dot (QD) spin light emitting diode (spin-LED) under zero applied magnetic field. A high degree of electroluminescence circular polarization (Pc) ~19% is measured in remanence up to 100K. This result is obtained thanks to the combination of a perpendicularly magnetized CoFeB/MgO spin injector allowing efficient spin injection and an appropriate p-doped InGaAs/GaAs QD layer in the active region. By analyzing the bias and temperature dependence of the electroluminescence circular polarization, we have evidenced a two-step spin r…
Cavity polaritons have been shown these last years to exhibit a rich variety of non-linear behaviors which could be used in new polariton based devices. Operation in the strong coupling regime under electrical injection remains a key step toward a practical polariton device. We report here on the realization of a polariton based light emitting diode using a GaAs microcavity with doped Bragg mirrors. Both photocurrent and electroluminescence spectra are governed by cavity polaritons up to 100 K.
We employ optical pump-probe spectroscopy to investigate the voltage dependence of spontaneous electron and nuclear spin polarizations in hybrid MnAs/n-GaAs and Fe/n-GaAs Schottky diodes. Through the hyperfine interaction, nuclear spin polarization that is imprinted by the ferromagnet acts on conduction electron spins as an effective magnetic field. We demonstrate tuning of this nuclear field from <0.05 to 2.4 kG by varying a small bias voltage across the MnAs device. In addition, a connection is observed between the diode turn-on and the onset of imprinted nuclear polarization, while traditio…
We demonstrate highly efficient spin injection at low and room temperature in an AlGaAs/GaAs semiconductor heterostructure from a CoFe/AlOx tunnel spin injector. We use a double-step oxide deposition for the fabrication of a pinhole-free AlOx tunnel barrier. The measurements of the circular polarization of the electroluminescence in the Oblique Hanle Effect geometry reveal injected spin polarizations of at least 24% at 80K and 12% at room temperature.
Planar light-emitting diodes (LEDs) fabricated within a single high-mobility quantum well are demonstrated. Our approach leads to a dramatic reduction of radiative lifetime and junction area with respect to conventional vertical LEDs, promising very high-frequency device operation. Devices were fabricated by UV lithography and wet chemical etching starting from p-type modulation-doped AlGaAs/GaAs heterostructures grown by molecular beam epitaxy. Electrical and optical measurements from room temperature down to 1.8 K show high spectral purity and high external efficiency. Time-resolved measurem…
Electrical spin injection from the Heusler alloy Co_2MnGe into a p-i-n Al_0.1Ga_0.9As/GaAs light emitting diode is demonstrated. A maximum steady-state spin polarization of approximately 13% at 2 K is measured in two types of heterostructures. The injected spin polarization at 2 K is calculated to be 27% based on a calibration of the spin detector using Hanle effect measurements. Although the dependence on electrical bias conditions is qualitatively similar to Fe-based spin injection devices of the same design, the spin polarization injected from Co_2MnGe decays more rapidly with increasing te…
We demonstrate a large electrical spin injection into GaAs at zero magnetic field thanks to an ultrathin perpendicularly magnetized CoFeB contact of a few atomic planes (1.2 nm). The spin-polarization of electrons injected into GaAs was examined by the circular polarization of electroluminescence from a Spin Light Emitting Diode with embedded InGaAs/GaAs quantum wells. The electroluminescence polarization as a function of the magnetic field closely traces the out-of-plane magnetization of the CoFeB/MgO injector. A circular polarization degree of the emitted light as large as 20% at 25 K is ach…
An efficient electrical spin injection into an InGaAs/GaAs quantum well light emitting diode is demonstrated thanks to a CoFeB/MgO spin injector. The textured MgO tunnel barrier is fabricated by two different techniques: sputtering and molecular beam epitaxy (MBE). The maximal spin injection efficiency is comparable for both methods. Additionally, the effect of annealing is also investigated for the two types of samples. Both samples show the same trend: an increase of the electroluminescence circular polarization (Pc) with the increase of annealing temperature, followed by a saturation of Pc …
We report on a process that enables the removal of II-VI semiconductor epilayers from their GaAs growth substrate and their subsequent transfer to arbitrary host environments. The technique combines mechanical lapping and layer selective chemical wet etching and is generally applicable to any II-VI layer stack. We demonstrate the non-invasiveness of the method by transferring an all-II-VI magnetic resonant tunneling diode. High resolution X-ray diffraction proves that the crystal integrity of the heterostructure is preserved. Transport characterization confirms that the functionality of the de…
We explore the nature of the electroluminescence (EL) emission of purely n-doped GaAs/AlGaAs resonant tunneling diodes (RTDs) and the EL evolution with voltage. A singular feature of such a device is unveiled when the electrical output current changes from high to low and the EL on-off ratio is enhanced by 2 orders of magnitude compared to the current on-off ratio. By combining the EL and current properties, we are able to identify two independent impact ionization channels associated with the coherent resonant tunneling current and the incoherent valley current. We also perform the same inves…
We investigate spin-polarized inter-band tunneling through measurement of (Ga,Mn)As based Zener tunnel diode. By placing the diode under reverse bias, electron spin polarization is transferred from the valence band of p-type (Ga,Mn)As to the conduction band of an adjacent n-GaAs layer. The resulting current is monitored by injection into a quantum well light emitting diode whose electroluminescence polarization is found to track the magnetization of the (Ga,Mn)As layer as a function of both temperature and magnetic field.
We study the magneto-transport and magneto-electroluminescence properties of purely n-doped GaAs/Al$_{0.6}$Ga$_{0.4}$As resonant tunneling diodes with an In$_{0.15}$Ga$_{0.85}$As quantum well and emitter prewell. Before the resonant current condition, magneto-transport measurements reveal charge carrier densities comparable for diodes with and without the emitter prewell. The Landau level splitting is observed in the electroluminescence emission from the emitter prewell, enabling the determination of the charge carrier build-up. Our findings show that magneto-electroluminescence spectroscopy t…
The Landauer-Buettiker formalism combined with the tight-binding transfer matrix method is used to describe the results of recent experiments: the high tunneling magnetoresistance (TMR) in (Ga,Mn)As-based trilayers and highly polarized spin injection in p-(Ga,Mn)As/n-GaAs Zener diode. For both TMR and Zener spin current polarization, the calculated values agree well with those observed experimentally. The role played in the spin dependent tunneling by carrier concentration and magnetic ion content is also studied.
Strained coherent heteroepitaxy of III-V semiconductor films such as In$_x$Ga$_{1-x}$As/GaAs has potential for electronic and optoelectronic applications such as high density logic, quantum computing architectures, laser diodes, and other optoelectronic devices. Crystal symmetry can have a large effect on the morphology of these films and their spatial order. Often the formation of group IV strained heterostructures such as Ge deposited on Si is analyzed using analytic models based on the Asaro-Tiller-Grinfeld instability. However, the governing dynamics of III-V 3D heterostructure formation h…
Spintronics has attracted wide attention by promising novel functionalities derived from both the electron charge and spin. While branching into new areas and creating new themes over the past years, the principal goals remain the spin and magnetic control of the electrical properties, essentially the I-V characteristics, and vice versa. There are great challenges ahead to meet these goals. One challenge is to find niche applications for ferromagnetic semiconductors, such as GaMnAs. Another is to develop further the science of hybrid ferromagnetic metal/semiconductor heterostructures, as alter…
Numerous efforts have been devoted to improve the electronic and optical properties of III-V compound materials via reduction of their nonradiative states, aiming at highly-efficient III-V sub-micrometer devices. Despite many advances, there is still a controversial debate on which combination of chemical treatment and capping dielectric layer can best reproducibly protect the crystal surface of III-Vs, while being compatible with readily available plasma deposition methods. This work reports on a systematic experimental study on the role of sulfide ammonium chemical treatment followed by diel…
We report experimental evidence of excitonic spin-splitting, in addition to the conventional Zeeman effect, produced by a combination of the Rashba spin-orbit interaction, Stark shift and charge screening. The electric-field-induced modulation of the spin-splitting are studied during the charging and discharging processes of p-type GaAs/AlAs double barrier resonant tunneling diodes (RTD) under applied bias and magnetic field. The abrupt changes in the photoluminescence, with the applied bias, provide information of the charge accumulation effects on the device.
