Electrical injection and detection of spin-polarized electrons is demonstrated for the first time in a single wafer, all-semiconductor, GaAs-based lateral spintronic device, employing p+-(Ga,Mn)As/n+-GaAs ferromagnetic Esaki diodes as spin aligning contacts. The conversion of spin-polarized holes into spin-polarized electrons via Esaki tunnelling leaves its mark in a bias dependence of the spin-injection efficiency, which at maximum reaches the relatively high value of 50%.
Electrical injection of spin-polarized electrons into a semiconductor, large spin diffusion length, and an integration friendly platform are desirable ingredients for spin-based devices. Here we demonstrate lateral spin injection and detection in germanium nanowires, by using ferromagnetic metal contacts and tunnel barriers for contact resistance engineering. Using data measured from over 80 samples, we map out the contact resistance window for which lateral spin transport is observed, manifestly showing the conductivity matching required for spin injection. Our analysis, based on the spin dif…
The current-voltage characteristic and ideality factor of III-Nitride quantum well light-emitting diodes (LEDs) grown on bulk GaN substrates are investigated. At operating temperature, these electrical properties exhibit a simple behavior. A model in which only active-region recombinations have a contribution to the LED current is found to account for experimental results. The limit of LED electrical efficiency is discussed based on the model and on thermodynamic arguments, and implications for electroluminescent cooling are examined.
We report the successful extraction of spin polarized current from the organic-based room temperature ferrimagnetic semiconductor V[TCNE]x (x~2, TCNE: tetracyanoethylene; TC ~ 400 K, EG ~ 0.5 eV, s ~ 10-2 S/cm) and its subsequent injection into a GaAs/AlGaAs light-emitting diode (LED). The spin current tracks the magnetization of V[TCNE]x~2, is weakly temperature dependent, and exhibits heavy hole / light hole asymmetry. This result has implications for room temperature spintronics and the use of inorganic materials to probe spin physics in organic and molecular systems.
We report on the unambiguous detection of Auger electrons by electron emission spectroscopy from a cesiated InGaN/GaN light emitting diode (LED) under electrical injection. Electron emission spectra were measured as a function of the current injected in the device. The appearance of high energy electron peaks simultaneously with an observed drop in electroluminescence efficiency shows that hot carriers are being generated in the active region (InGaN quantum wells) by an Auger process. A linear correlation was measured between the high energy emitted electron current and the "droop current" - t…
Epitaxial NbO2 (110) films, 20 nm thick, were grown by pulsed laser deposition on Al2O3 (0001) substrates. The Ar/O2 total pressure during growth was varied to demonstrate the gradual transformation between NbO2 and Nb2O5 phases, which was verified using x-ray diffraction, x-ray photoelectron spectroscopy, and optical absorption measurements. Electric resistance threshold switching characteristics were studied in a lateral geometry using interdigitated Pt top electrodes in order to preserve the epitaxial crystalline quality of the films. Volatile and reversible transitions between high and low…
In this letter, we report on successful electrical spin injection and detection in \textit{n}-type germanium-on-insulator (GOI) using a Co/Py/Al$_{2}$O$_{3}$ spin injector and 3-terminal non-local measurements. We observe an enhanced spin accumulation signal of the order of 1 meV consistent with the sequential tunneling process via interface states in the vicinity of the Al$_{2}$O$_{3}$/Ge interface. This spin signal is further observable up to 220 K. Moreover, the presence of a strong \textit{inverted} Hanle effect points at the influence of random fields arising from interface roughness on t…
An efficient electrical spin injection into an InGaAs/GaAs quantum well light emitting diode is demonstrated thanks to a CoFeB/MgO spin injector. The textured MgO tunnel barrier is fabricated by two different techniques: sputtering and molecular beam epitaxy (MBE). The maximal spin injection efficiency is comparable for both methods. Additionally, the effect of annealing is also investigated for the two types of samples. Both samples show the same trend: an increase of the electroluminescence circular polarization (Pc) with the increase of annealing temperature, followed by a saturation of Pc …
We demonstrate spin polarized tunneling from Fe through a SiO2 tunnel barrier into a Si n-i-p heterostructure. Transport measurements indicate that single step tunneling is the dominant transport mechanism. The circular polarization, Pcirc, of the electroluminescence (EL) shows that the tunneling spin polarization reflects Fe majority spin. Pcirc tracks the Fe magnetization, confirming that the spin-polarized electrons radiatively recombining in the Si originate from the Fe. A rate equation analysis provides a lower bound of 30% for the electron spin polarization in the Si at 5 K.
In this article a detailed characterization of a magnetization motion in a single sub-micrometer and multi-terminal ferromagnetic structure in lateral geometry is performed in a GHz regime using direct DC characterization technique. We have shown applicability of the Stoner-Wohlfarth model to the magnetic nano-structure with large length to with ratio. Applying the model to experimental data we are able to extract relevant magnetization motion parameters and show a correlation between high frequency inductive currents and local magnetization. Additionally, DC voltage generated over the structu…
We demonstrate a large electrical spin injection into GaAs at zero magnetic field thanks to an ultrathin perpendicularly magnetized CoFeB contact of a few atomic planes (1.2 nm). The spin-polarization of electrons injected into GaAs was examined by the circular polarization of electroluminescence from a Spin Light Emitting Diode with embedded InGaAs/GaAs quantum wells. The electroluminescence polarization as a function of the magnetic field closely traces the out-of-plane magnetization of the CoFeB/MgO injector. A circular polarization degree of the emitted light as large as 20% at 25 K is ach…
Non-local carrier injection/detection schemes lie at the very foundation of information manipulation in integrated systems. This paradigm consists in controlling with an external signal the channel where charge carriers flow between a "source" and a well separated "drain". The next generation electronics may operate on the spin of carriers instead of their charge and germanium appears as the best hosting material to develop such a platform for its compatibility with mainstream silicon technology and the long electron spin lifetime at room temperature. Moreover, the energy proximity between the…
The effect of nuclear spins in Fe/GaAs all-electrical spin-injection devices is investigated. At temperatures below 50 K, strong modifications of the non-local spin signal are found that are characteristic for hyperfine coupling between conduction electrons and dynamically polarized nuclear spins. The perpendicular component of the nuclear Overhauser field depolarizes electron spins near zero in-plane external magnetic field, and can suppress such dephasing when antialigned with the external field, leading to satellite peaks in a Hanle measurement. The features observed agree well with a Monte…
We report on a local spin valve effect observed unambiguously in lateral all-semiconductor all-electrical spin injection devices, employing p+-(Ga,Mn)As/n+-GaAs Esaki diode structures as spin aligning contacts. We discuss the observed local spin-valve signal as a result of interplay between spin-transport-related contribution and tunneling anisotropic magnetoresistance of magnetic contacts. The magnitude of the spin-related magnetoresistance change is equal to 30 Ohm which is twice the magnitude of the measured non-local signal.
We have investigated electrical spin injection from Ni81Fe19 into an InAs quantum well through MgO tunneling barrier for potential application to InAs-based spin field effect transistor. Injected spin polarized current were detected in both nonlocal and local spin valve set-ups and the spin diffusion length and spin injection efficiency were analyzed. The spin diffusion length was estimated to be 1.6 μm in nonlocal set-up at 1.4 K. The spin polarization of Ni81Fe19/MgO/InAs as-deposited sample was relealed to be 6.9 %, while increased spin polarization of 8.9 % was observed by additional therm…
We demonstrate the electrical injection and detection of spin-polarized electrons in the Co2FeSi/GaAs hybrid system using lateral transport structures. Spin valve signatures and characteristic Hanle curves are observed both in the nonlocal and the local configuration. The comparatively large magnitude of the local spin valve signal and the high signal-to-noise ratio are attributed to the large spin polarization at the Fermi energy of Co2FeSi in the well-ordered L21 phase.
We report here on anisotropy of spin polarization obtained in lateral all-semiconductor all-electrical spin injection devices, employing $p^{+}-$(Ga,Mn)As/$n^{+}-$GaAs Esaki diode structures as spin aligning contacts, resulting from the dependence of the efficiency of spin tunneling on the orientation of spins with respect to different crystallographic directions. We observed an in-plane anisotropy of $~8%$ in case of spins oriented either along $[1\bar{1}0]$ or $[110]$ directions and $~25%$ anisotropy between in-plane and perpendicular-to-plane orientation of spins.
We observed spin injection into silicon through Fe/MgO tunnel barrier by using non-local magnetoresistance measurement technique. Fe/MgO tunnel barrier contacts with a lateral spin valve structure were fabricated on phosphorous doped silicon-on-insulator substrate. Spin injection signals in the non-local scheme were observed up to 120K, which is the highest value where band transferred spins in Si have ever been reported, and spin diffusion length was estimated to be about 2.25um at 8K. Temperature dependence and injection current dependence of the non-local voltage were also investigated. It …
We use electrical spin injection to probe exchange interactions in phosphorus doped silicon (Si:P). The detection is enabled by a magnetoresistance effect that demonstrates the efficiency of exchange in imprinting spin information from the magnetic lead onto the localized moments in the Si:P region. A unique Lorentzian-shaped signal existing only at low temperatures ($\lesssim 25 K$) is observed experimentally and analyzed theoretically in electrical Hanle effect measurement. It stems from spin-dependent scattering of electrons by neutral impurities in Si:P. The shape of this signal is not dir…
The nonlocal spin resistance is measured as a function of temperature in a Fe/GaAs spin-injection device. For nonannealed samples that show minority-spin injection, the spin resistance is observed up to room temperature and decays exponentially with temperature at a rate of 0.018\,K$^{-1}$. Post-growth annealing at 440\,K increases the spin signal at low temperatures, but the decay rate also increases to 0.030\,K$^{-1}$. From measurements of the diffusion constant and the spin lifetime in the GaAs channel, we conclude that sample annealing modifies the temperature dependence of the spin transf…
We demonstrate electrical injection and detection of spin-polarized electrons in silicon (Si) using epitaxially grown Fe_3Si/Si Schottky-tunnel-barrier contacts. By an insertion of a delta-doped n^+-Si layer (~ 10^19 cm^-3) near the interface between a ferromagnetic Fe_3Si/Si contact and a Si channel (~ 10^15 cm^-3), we achieve a marked enhancement in the tunnel conductance for reverse-bias characteristics of the Fe_3Si/Si Schottky diodes. Using laterally fabricated four-probe geometries with the modified Fe_3Si/Si contacts, we detect nonlocal output signals which originate from the spin accum…
In this paper, SiO2 layers deposited on 4H-SiC and subjected to different post deposition annealing (PDA) in NO and N2O were studied to identify the key factors influencing the channel mobility and threshold voltage stability in 4H-SiC MOSFETs. In particular, PDA in NO gave a higher channel mobility (55 cm2V-1s-1) than PDA in N2O (20 cm2V-1s-1), and the subthreshold behavior of the devices confirmed a lower total amount of interface states for the NO case. This latter could be also deduced from the behavior of the capacitance-voltage characteristics of 4H-SiC MOSFETs measured in gate controlle…
Spin injection and detection in Co60Fe40-based all-metallic lateral spin-valves have been studied at both room and low temperatures. The obtained spin signals amplitudes have been compared to that of identical Ni80Fe20-based devices. The replacement of Ni80Fe20 by CoFe allows increasing the spin signal amplitude by up to one order of magnitude, thus reaching 50 mΩ at room temperature. The spin signal dependence with the distance between the ferromagnetic electrodes has been analyzed using both a 1D spin transport model and finite elements method simulations. The enhancement of the spin signal …
The domain-wall/metal-electrode injection barrier in lithium niobate: Which electrical transport model fits best?
Institute of Applied Physics, Technische Universität Dresden（德累斯顿工业大学应用物理研究所）；Experimental Physics V, Center for Electronic Correlations and Magnetism, University of Augsburg（奥格斯堡大学电子关联与磁学中心实验物理学V）；Würzburg-Dresden Cluster of Excellence (EXC 2147) ctd.qmat – Complexity, Topology, and Dynamics in Quantum Matter（维尔茨堡-德累斯顿卓越集群（EXC 2147）ctd.qmat——量子物质的复杂性、拓扑和动力学）；Institute for Photonic Quantum Systems (PhoQS), Department of Physics, University of Paderborn（帕德博恩大学物理学院光子量子系统研究所）
In a recent publication, we demonstrated electrical spin injection and detection in n-type silicon at temperatures up to 500K using ferromagnetic metal / SiO2 tunnel barrier contacts in a three-terminal geometry (Nature Commun. 2:245 doi:10.1038/ncomms125 (2011)). In comparing our measured spin-voltage signal with the value predicted by theory, we followed the analysis of Tran et al, (Phys. Rev. Lett. 102, 036601 (2009)), and inadvertently propagated an error found therein. As they note in a recent erratum (arXiv:0810.4770v2), the correct expression for the spin resistance area product from th…
Charge carrier recombination in the perovskite solar cells (PSCs) has a deep influence on the electrical performance, such as open circuit voltage, short circuit current, fill factor and ultimately power conversion efficiency. The impacts of injection barrier, recombination channels, doping properties of carrier transport layers and light intensity on the performance of PSCs are theoretically investigated by drift-diffusion model in this work. The results indicate that due to the injection barrier at the interfaces of perovskite and carrier transport layer, the accumulated carriers modify the …
The current research in graphene spintronics strives for achieving a long spin lifetime, and efficient spin injection and detection in graphene. In this article, we review how hexagonal boron nitride (hBN) has evolved as a crucial substrate, as an encapsulation layer, and as a tunnel barrier for manipulation and control of spin lifetimes and spin injection/detection polarizations in graphene spin valve devices. First, we give an overview of the challenges due to conventional SiO$_2$ substrate for spin transport in graphene followed by the progress made in hBN based graphene heterostructures. T…
Electric-field control of spin-dependent properties has become one of the most attractive phenomena in modern materials research due the promise of new device functionalities. One of the paradigms in this approach is to electrically toggle the spin polarization of carriers injected into a semiconductor using ferroelectric polarization as a control parameter. Using first-principles density functional calculations, we explore the effect of ferroelectric polarization of electron-doped BaTiO3 (n-BaTiO3) on the spin-polarized transmission across the SrRuO3/n-BaTiO3 (001) interface. Our study reveal…
We report the successful electrical creation of spin polarization in p-type Si at room temperature by using an epitaxial MgO(001) tunnel barrier and Fe(001) electrode. Reflection high-energy electron diffraction observations revealed that epitaxial Fe/MgO(001) tunnel contacts can be grown on a (2 x 1) reconstructed Si surface whereas tunnel contacts grown on the (1 x 1) Si surface were polycrystalline. Transmission electron microscopy images showed a more flat interface for the epitaxial Fe/MgO/Si compared to that of the polycrystalline structure. For the Fe/MgO/p-Si devices, the Hanle and inv…
We inject spin-polarized electrons from an Fe/MgO tunnel barrier contact into n-type Ge(001) substrates with electron densities 2e16 < n < 8e17 cm-3, and electrically detect the resulting spin accumulation using three-terminal Hanle measurements. We observe significant spin accumulation in the Ge up to room temperature. We observe precessional dephasing of the spin accumulation (the Hanle effect) in an applied magnetic field for both forward and reverse bias (spin extraction and injection), and determine spin lifetimes and corresponding diffusion lengths for temperatures of 225 K to 300 K. The…
We demonstrate electrical spin injection into multilayer graphene (MLG) in a lateral spin valve device from a highly spin-polarized Co2FeSi (CFS) Huesler electrode. Exfoliated MLG was transferred onto pre-patterned epitaxial CFS wires grown on an Si(111) substrate by a polymer-based transfer method. This method enabled us to fabricate multiple single-crystal CFS electrodes in contact with MLG. Electrical spin injection from CFS to MLG was detected through non-local magnetoresistance (MR) measurement. A non-local spin signal of 430 ohm was observed; this is the largest value among all reported …
The effect of applying an external electric field on doping-induced spin-orbit splitting of the lowest conduction-band states in a bismuth-doped zinc oxide nanowire is studied by performing electronic structure calculations within the framework of density functional theory. It is demonstrated that spin splitting in Bi-doped ZnO nanowires could be tuned and enhanced electrically via control of the strength and direction of the applied electric field, thanks to the nonuniform and anisotropic response of the ZnO:Bi nanowire to external electric fields. The results reported here indicate that a si…
Room temperature local magnetoresistance in two-terminal scheme is reported. By employing 1.6 nm-thick MgO tunnel barrier, spin injection efficiency is increased, resulting in large non-local magnetoresistance. The magnitude of the non-local magnetoresistance is estimated to be 0.0057 ohm at room temperature. As a result, a clear rectangle signal is observed in local magnetoresistance measurement even at room temperature. We also investigate the origin of local magnetoresistance by measuring the spin accumulation voltage of each contact separately.
Two dimensional (2D) materials provide a unique platform for spintronics and valleytronics due to the ability to combine vastly different functionalities into one vertically-stacked heterostructure, where the strengths of each of the constituent materials can compensate for the weaknesses of the others. Graphene has been demonstrated to be an exceptional material for spin transport at room temperature, however it lacks a coupling of the spin and optical degrees of freedom. In contrast, spin/valley polarization can be efficiently generated in monolayer transition metal dichalcogenides (TMD) suc…
We performed non-local electrical measurements of a series of Py/Cu lateral spin valve devices with different Cu thicknesses. We show that both the spin diffusion length of Cu and the apparent spin polarization of Py increase with Cu thickness. By fitting the results to a modified spin-diffusion model, we show that the spin diffusion length of Cu is dominated by spin-flip scattering at the surface. In addition, the dependence of spin polarization of Py on Cu thickness is due to a strong spin-flip scattering at the Py/Cu interface.
We show that local injection of pure spin current into an electrically disconnected ferromagnetic - normal-metal sandwich induces electric currents, that run along closed loops inside the device, and are powered by the source of the spin injection. Such electric currents may significantly modify voltage distribution in spin-injection devices and induce long-range tails of spin accumulation.
In this letter, we first show electrical spin injection in the germanium conduction band at room temperature and modulate the spin signal by applying a gate voltage to the channel. The corresponding signal modulation agrees well with the predictions of spin diffusion models. Then by setting a temperature gradient between germanium and the ferromagnet, we create a thermal spin accumulation in germanium without any tunnel charge current. We show that temperature gradients yield larger spin accumulations than pure electrical spin injection but, due to competing microscopic effects, the thermal sp…
We demonstrate that information can be transmitted and processed with pure spin currents in silicon. Fe/Al2O3 tunnel barrier contacts are used to produce significant electron spin polarization in the silicon, generating a spin current which flows outside of the charge current path. The spin orientation of this pure spin current is controlled in one of three ways: (a) by switching the magnetization of the Fe contact, (b) by changing the polarity of the bias on the Fe/Al2O3 (injector) contact, which enables the generation of either majority or minority spin populations in the Si, providing a way…
