We report on the observation of puzzling nonuniform, but ordered, frequency combs in erbium-doped fiber lasers at low temperatures, between 3 K and 14 K. At ~14 K the combs disappear. The combs contain ~240 lines and have nonuniform frequency spacings that starts from ~25 GHz at ~1540.5 nm and decreases, almost monotonically, to ~100 MHz within (1.8-2) nm. We discuss possibilities that they result from enlarged regular mode-comb spacings, from prime numbers-based solitary waves free of four-wave mixing or result from gain gratings. However, we think that the combs originate from multi-lasing lines allowed in inhomogeneous gain broadening, dominant at low temperatures, together with a small power dependent homogeneous broadening part, responsible for the spacing between the lines.
We demonstrated the observation of Rb two-photon absorption directly excided by an optical frequency comb at fiber communication bands. A chain of comb spectral control is elaborately implemented to increase the power of the second harmonic optical frequency comb generation and the two-photon transition strength. A two-photon transition spectrum is obtained with clearly resolved transition lines. It provides a potential approach to realize the optical frequency comb or optical clock at ~1.5μm with high stability and accuracy.
We demonstrate an optical frequency comb based on an erbium-doped-fiber femtosecond laser with the nonlinear polarization evolution scheme. The repetition rate of the laser is about 209 MHz. By controlling an intra-cavity electro-optic modulator and a piezo-transducer, the repetition rate can be stabilized with high servo bandwidth in a range of 3 kHz, enabling long-term repetition rate phase-locking. The in-loop frequency stability of repetition rate is about 1.6E-13 at 1 second integration time, limited by the measurement system; and it is inversely proportional to integration time in short …
Optical fiber tapers are used to collect photoluminescence emission at ~1.5 um from photonic crystal cavities fabricated in erbium doped silicon nitride on silicon. Photoluminescence collection via fiber taper is enhanced 2.5 times relative to free space, with a total taper collection efficiency of 53%. By varying the fiber taper offset from the cavity, a broad tuning range of coupling strength is obtained. This material system combined with fiber taper collection is promising for building on-chip optical amplifiers.
A tunable and switchable multi-wavelength erbium-doped fiber ring laser based on a new type tunable comb filter is proposed and demonstrated. By adjusting the polarization controllers, dual-function operation of the channel spacing tunability and the wavelength switching (interleaving) can be readily achieved. Up to 29 stable lasing lines with 0.4 nm spacing and 14 lasing wavelengths with 0.8 nm spacing in 3 dB bandwidth were obtained at room temperature. In addition, the lasing output, including the number of the lasing lines, the lasing evenness and the lasing locations, can also be flexibly…
A compact and robust coherent laser light source that provides spectral coverage from the ultraviolet to infrared is desirable for numerous applications, including heterodyne super resolution imaging[1], broadband infrared microscopy[2], protein structure determination[3], and standoff atmospheric trace-gas detection[4]. Addressing these demanding measurement problems, laser frequency combs[5] combine user-defined spectral resolution with sub-femtosecond timing and waveform control to enable new modalities of high-resolution, high-speed, and broadband spectroscopy[6-9]. In this Letter we intro…
We present a laser frequency comb based upon a 250 MHz mode-locked erbium-doped fiber laser that spans more than 300 terahertz of bandwidth, from 660 nm to 2000 nm. The system generates 1.2 nJ, 70 fs pulses at 1050 nm by amplifying the 1580 nm laser light in Er:fiber, followed by nonlinear broadening to 1050 nm and amplification in Yb:fiber. Extension of the frequency comb into the visible is achieved by supercontinuum generation from the 1050 nm light. Comb coherence is verified with cascaded f-2f interferometry and comparison to a frequency stabilized laser.
Space-division multiplexing (SDM), whereby multiple spatial channels in multimode and multicore optical fibers are used to increase the total transmission capacity per fiber, is being investigated to avert a data capacity crunch and reduce the cost per transmitted bit. With the number of channels employed in SDM transmission experiments continuing to rise, there is a requirement for integrated SDM components that are scalable. Here, we demonstrate a cladding-pumped SDM erbium-doped fiber amplifier (EDFA) that consists of six uncoupled multimode erbium-doped cores. Each core supports three spat…
We proposed a narrow spectral bandwidth Erbium-doped fiber (EDF) laser Q-switched by a homemade saturable dynamic induced grating (SDIG) which is introduced via reforming the structure of a fiber saturable absorbers FSA with a piece of EDF and a fiber Bragg grating. The SDIG integrates both saturable absorption and spectral filtering effect simultaneously, which was confirmed through theoretical analysis and experimental results for the first time, to the best of our knowledge. Further study verified that the spectral width of the Q-switched emissions is decided by the length of the SDIG and t…
Lithium niobate on insulator (LNOI), regarded as an important candidate platform for optical integration due to its excellent nonlinear, electro-optic and other physical properties, has become a research hotspot. Light source, as an essential component for integrated optical system, is urgently needed. In this paper, we reported the realization of 1550-nm band on-chip LNOI microlasers based on erbium-doped LNOI ring cavities with loaded quality factors higher than one million, which were fabricated by using electron beam lithography and inductively coupled plasma reactive ion etching processes…
We use two femtosecond Erbium-doped fiber lasers with slightly different repetition rates to perform a modern type of Fourier transform spectroscopy without moving parts. The measurements are done in real time, and it takes less than 50 microseconds. We work with somewhat different spectral outputs from two Erbium-doped fiber lasers and employ spectral filtering based on a 2f-2f grating setup to select the common spectral region of interest, thereby increasing the signal-to-noise ratio. The interferogram is taken with a 20 cm long gas cell, containing a mixture of acetylene and air at atmosphe…
A high-performance S-band single-longitudinal-mode (SLM) erbium-doped fiber (EDF) ring cavity laser based on a depressed cladding EDF is investigated and experimentally demonstrated. We combine a double-ring passive resonator (DR-PR) and a length of unpumped polarization maintaining (PM) EDF in the laser cavity to achieve the SLM lasing without mode hopping. The DR-PR, composed of two efficient dual-coupler fiber rings, is utilized to expand the free spectral range of the EDF ring cavity laser and to eliminate the dense longitudinal modes greatly. The PM EDF, insusceptible to random change ind…
For erbium-doped amorphous oxides, such as those that are used in compact lightwave devices interfaced with silicon, values of the refractive indices are commonly obtained empirically. This work, combining experimental and theoretical studies, examines silica as the exemplary host and the influence of erbium doping on the refractive index. Analysis of data is presented for the spectral refractive index in the ultraviolet to near infrared wavelength range of heavily erbium-doped silica thin films prepared by spin coating a sol-gel precursor on silicon and subsequent vacuum annealing. Effective …
Upconversion of infrared photons is a promising possibility to enhance solar cell efficiency by producing electricity from otherwise unused sub-band-gap photons. We present a rate equation model, and the relevant processes, in order to describe upconversion of near-infrared photons. The model considers stimulated and spontaneous processes, multi-phonon relaxation and energy transfer between neighboring ions. The input parameters for the model are experimentally determined for the material system β-NaEr0.2Y0.8F4. The determination of the transition probabilities, also known as the Einstein coef…
The influence of low temperatures on the performance of a high-power single-frequency fiber laser amplifier is evaluated with a numerical simulation. Cooling the fiber can allow to take advantage of both higher damping of the acoustic waves in the silica glass, and higher laser efficiency. We first report on the measurement of the stimulated Brillouin scattering (SBS) threshold in a silica fiber as a function of the temperature from 300~K down to 77~K. We then present the measurements of small-signal absorption and gain spectra of an erbium doped alumino-phosphosilicate fiber, at room temperat…
High-efficiency integrated laser on erbium-doped lithium niobate-on-insulator
MOE Key Laboratory of Weak-Light Nonlinear Photonics, School of Physics and TEDA Institute of Applied Physics, Nankai University（南开大学物理学院与泰达应用物理研究院弱光非线性光子学教育部重点实验室）
Laser frequency combs based on erbium-doped fiber mode-locked lasers have shown great potential for compact, robust and efficient optical clock comparisons. However, to simultaneously compare multiple optical clock species, fiber laser frequency combs typically require multiple amplifiers and fiber optic paths that reduce the achievable frequency stability near 1 part in $10^{16}$ at 1s. In this paper we describe an erbium-fiber laser frequency comb that overcomes these conventional challenges and supports optical frequency synthesis at the millihertz level, or fractionally $3 x 10^{-18}$ $tau…
Combining the quantum optical properties of single-photon emitters with the strong near-field interactions available in nanophotonic and plasmonic systems is a powerful way of creating quantum manipulation and metrological functionalities. The ability to actively and dynamically modulate emitter-environment interactions is of particular interest in this regard. While thermal, mechanical and optical modulation have been demonstrated, electrical modulation has remained an outstanding challenge. Here we realize fast, all-electrical modulation of the near-field interactions between a nanolayer of …
Magneto-Optic Photonic Crystals (MOPC) used in low dimension lasers whereby acting as Faraday rotators capable of 45o rotation where insertion loos is compensated by photoluminescence effect are of significant interest. In low dimension sensors MOPCs act as optical filters to selectively detect only lights at certain wavelengths. Combined with the photoluminescence effect, sensors may be designed capable of detecting signals with extremely low intensity, thus high quantum efficiency. In this work, MOPC with various Erbium dopant concentrations, acting as photoluminescence center, were modelled…
Ultrasensitive detection of methane, isotopic carbon dioxide, carbon monoxide, formaldehyde, acetylene and ethylene is performed in the spectral range 2.5 - 5 μm using intracavity spectroscopy in broadband optical parametric oscillators (OPOs). The OPOs were operated near degeneracy and synchronously pumped either by a mode-locked erbium (1560 nm) or thulium (2050 nm) fiber laser. A large instantaneous bandwidth of up to 800 cm$^{-1}$ allows for simultaneous detection of several gases. We observe an effective path length enhancement due to coherent interaction inside the OPO cavity and achieve…
Dual-comb microscopy (DCM), based on a combination of dual-comb spectroscopy (DCS) with two-dimensional spectral encoding (2D-SE), is a promising method for scan-less confocal laser microscopy giving an amplitude and phase image contrast with the confocality. However, signal loss in a 2D-SE optical system hampers increase in image acquisition rate due to decreased signa-to-noise ratio. In this article, we demonstrated optical image amplification in DCM with an erbium-doped fiber amplifier (EDFA). Combined use of image-encoded DCS interferogram and EDFA benefits from not only the batch amplific…
In this letter, we report on all-optical fiber approach to the generation of ultra-low noise microwave signals. We make use of two erbium fiber mode-locked lasers phase locked to a common ultra-stable laser source to generate an 11.55 GHz signal with an unprecedented relative phase noise of -111 dBc/Hz at 1 Hz from the carrier.The residual frequency instability of the microwave signals derived from the two optical frequency combs is below 2.3 10^(-16) at 1s and about 4 10^(-19) at 6.5 10^(4)s (in 5 Hz bandwidth, three days continuous operation).
We investigate the generation of optical frequency combs through a cascade of four-wave mixing processes in nonlinear fibres with optimised parameters. The initial optical field consists of two continuous-wave lasers with frequency separation larger than 40 GHz (312.7 pm at 1531 nm). It propagates through three nonlinear fibres. The first fibre serves to pulse shape the initial sinusoidal-square pulse, while a strong pulse compression down to sub-100 fs takes place in the second fibre which is an amplifying erbium-doped fibre. The last stage is a low-dispersion highly nonlinear fibre where the…
We demonstrate phase locking of a 729 nm diode laser to a 1542 nm master laser via an erbium-doped-fiber frequency comb, using a transfer-oscillator feedforward scheme which suppresses the effect of comb noise in an unprecedented 1.8 MHz bandwidth. We illustrate its performance by carrying out coherent manipulations of a trapped calcium ion with 99 % fidelity even at few-microsecond timescales. We thus demonstrate that transfer-oscillator locking can provide sufficient phase stability for high-fidelity quantum logic manipulation even without pre-stabilization of the slave diode laser.
The emerging microresonator-based frequency combs revolutionize a broad range of applications from optical communications to astronomical calibration. Despite of their significant merits, low energy efficiency and the lack of all-optical dynamical control severely hinder the transfer of microcomb system to real-world applications. Here, by introducing active lasing medium into the soliton microcomb, for the first time, we experimentally achieve the chiral soliton with agile on-off switch and tunable dual-comb generation in a packaged microresonator. It is found that such a microresonator enabl…
Time-resolved spectroscopic temperature measurements of a sealed carbon dioxide sample cell were realized with an optical frequency comb combined with a two-dimensional dispersive spectrometer. A supercontinuum laser source based on an erbium fiber mode-locked laser was employed to generate coherent light around 2000 nm (5000 cm-1). The laser was passed through a 12-cm long cell containing CO2, and the transmitted light was analyzed in a virtually imaged phased array- (VIPA-) based spectrometer. Broadband spectra spanning more than 100 cm-1 with a spectral resolution of roughly 0.075 cm-1 (2.2…
Mid-infrared optical frequency combs are of significant interest for molecular spectroscopy due to the large absorption of molecular vibrational modes on one hand, and the ability to implement superior comb-based spectroscopic modalities with increased speed, sensitivity and precision on the other hand. Substantial advances in mid-infrared frequency comb generation have been made in recent years based on nonlinear frequency conversion, microresonator Kerr frequency combs, quantum cascade lasers and mode locking regimes. Here we demonstrate a simple, yet effective method for the direct generati…
Fiber-based multi-wavelength lasers have a variety of important applications in telecommunication and meteorology. We experimentally study a fiber loop laser with an integrated Erbium doped fiber (EDF). The output optical spectrum is measured as a function of the EDF temperature. We find that below a critical temperature of about $10\unit{% K}$ the measured optical spectrum exhibits a sequence of narrow and unequally-spaced peaks. An intriguing connection between the peaks' wavelengths and the sequence of prime numbers is discussed. An hypothesis, which attributes the comb formation to intermo…
We describe and characterize a 25 GHz laser frequency comb based on a cavity-filtered erbium fiber mode-locked laser. The comb provides a uniform array of optical frequencies spanning 1450 nm to 1700 nm, and is stabilized by use of a global positioning system referenced atomic clock. This comb was deployed at the 9.2 m Hobby-Eberly telescope at the McDonald Observatory where it was used as a radial velocity calibration source for the fiber-fed Pathfinder near-infrared spectrograph. Stellar targets were observed in three echelle orders over four nights, and radial velocity precision of \sim10 m…
We report the construction and characterization of a narrow-linewidth laser system to interrogate the E2 clock transitions at 436 nm of ytterbium ions trapped in end-cap traps. The 871 nm seed laser at the fundamental frequency is referenced to a 10 cm long notched ULE cavity. The output of the laser system is delivered to a narrow-linewidth femtosecond fiber comb, which has been referenced to an ultrastable 698 nm laser, with a phase noise-canceled fiber link. The beat between the laser and the comb shows a sub-Hz linewidth, and with a stability better than 2E-15@1~100 s. The performance of t…
Non-perturbative and phase-sensitive light-matter interactions have led to the generation of attosecond pulses of light and the control electrical currents on the same timescale. Traditionally, probing these effects via high harmonic generation has involved complicated lasers and apparatuses to generate the few-cycle and high peak power pulses needed to obtain and measure spectra that are sensitive to the phase of the light wave. Instead, we show that nonlinear effects dependent on the carrier-envelope phase can be accessed in solid state crystals with simple low-energy frequency combs that we…
Tunable low-phase-noise terahertz synthesis using a fiber-interferometer-referenced optical frequency comb and an EDFA-integrated Vernier cavity
Graduate School of Sciences and Technology for Innovation, Tokushima University（德岛大学科学技术创新研究生院）；Department of Physics, Toho University（东海大学物理系）；Institute of Post-LED Photonics (pLED), Tokushima University（德岛大学后LED光子学研究所）；Institute of Photonics and Human Health Frontier (IPHF), Tokushima University（德岛大学光子学与人类健康前沿研究所）；Sevensix Inc.（Sevensix公司）
We present a hybrid fiber/waveguide design for a 100-MHz frequency comb that is fully self-referenced and temperature controlled with less than 5 W of electrical power. Self-referencing is achieved by supercontinuum generation in a silicon nitride waveguide, which requires much lower pulse energies (~200 pJ) than with highly nonlinear fiber. These low-energy pulses are achieved with an erbium fiber oscillator/amplifier pumped by two 250-mW passively-cooled pump diodes that consume less than 5 W of electrical power. The temperature tuning of the oscillator, necessary to stabilize the repetition…
We study the properties of a soliton crystal, an bound state of several optical pulses that propagate with a fixed temporal separation through the optical fibres of the proposed approach for generation of optical frequency combs (OFC) for astronomical spectrograph calibration. This approach - also being suitable for subpicosecond pulse generation for other applications - consists of a conventional single-mode fibre and a suitably pumped Erbium-doped fibre. Two continuous-wave lasers are used as light source. The soliton crystal arises out of the initial deeply modulated laser field at low inpu…
We have specifically investigated the free-space mode locking dynamics of erbium-doped fiber (EDF) mode-locked ultrafast lasers via nonlinear polarization rotation (NPR) in the normal dispersion regime. To do so, we built a passively mode-locked fiber laser based on NPR with a repetition rate of 89 MHz producing an octave-spanning spectrum due to supercontinuum (SC) generation in highly nonlinear fiber (HNLF). Most significantly, we have achieved highly stable self-starting NPR mode-locked femtosecond fiber laser based frequency comb which has been running mode locked for the past one year wit…
The effect of magnetron power on the room temperature 1.54 $μ$m infra-red photoluminescence intensity of erbium doped AlN films grown by r. f. magnetron sputtering, has been studied. The AlN:Er thin films were deposited on (001) Silicon substrates. The study presents relative photoluminescence intensities of nanocrystallized samples prepared with identical sputtering parameters for two erbium doping levels (0.5 and 1.5 atomic %). The structural evolution of the crystallites as a function of the power is followed by transmission electron microscopy. Copyright line will be provided by the publis…
Shot-noise-limited few-cycle mid-infrared frequency comb with attosecond phase stability
Wrocław University of Science and Technology（弗罗茨瓦夫理工大学）；University of Warsaw（华沙大学）；Center for Molecular Fingerprinting Research（分子指纹研究中心）；Max-Planck-Institute of Quantum Optics（马克斯·普朗克量子光学研究所）
A fully integrated dispersion-managed femtosecond mode-locked laser
Institute of Physics, Swiss Federal Institute of Technology Lausanne (EPFL)（洛桑联邦理工学院物理研究所）；Institute of Electrical and Micro Engineering, Swiss Federal Institute of Technology Lausanne (EPFL)（洛桑联邦理工学院电气与微工程学院）；EDWATEC SA（EDWATEC公司）；Helmholtz-Zentrum Dresden-Rossendorf (HZDR)（德累斯顿-罗森多夫亥姆霍兹中心）
We propose and demonstrate a high performance four-wavelength erbium-doped fiber laser (EDFL), enabled by a figure-8 compound-ring-cavity (F8-CRC) filter for single-longitudinal-mode (SLM) selection and a polarization-managed four-channel filter (PM-FCF) for defining four lasing wavelengths. We introduce a novel methodology utilizing signal-flow graph combined with Mason's rule to analyze a CRC filter in general and apply it to obtain the important design parameters for the F8-CRC filter used in this paper. By combining the functions of the F8-CRC filter and the PM-FCF filter assisted by the e…
