Millimeter-wave (mmWave) and terahertz (THz) spectrum can support significantly higher data rates compared to lower frequency bands and hence are being actively considered for 5G wireless networks and beyond. These bands have high free-space path loss (FSPL) in line-of-sight (LOS) propagation due to their shorter wavelength. Moreover, in non-line-of-sight (NLOS) scenario, these two bands suffer higher penetration loss than lower frequency bands which could seriously affect the network coverage. It is therefore critical to study the NLOS penetration loss introduced by different building materials at mmWave and THz bands, to help establish link budgets for an accurate performance analysis in indoor environments. In this work, we measured the penetration loss and the attenuation of several common constructional materials at mmWave (28 and 39 GHz) and sub-THz (120 and 144 GHz) bands. Measurements were conducted using a channel sounder based on NI PXI platforms. Results show that the penetration loss changes extensively based on the frequency and the material properties, ranging from 0.401 dB for ceiling tile at 28 GHz, to 16.608 dB for plywood at 144 GHz. Ceiling tile has the lowest measured attenuation at 28 GHz, while clear glass has the highest attenuation of 27.633 dB/cm at 144 GHz. As expected, the penetration loss and attenuation increased with frequency for all the tested materials.
Due to advantages in security and privacy, blockchain is considered a key enabling technology to support 6G communications. Practical Byzantine Fault Tolerance (PBFT) is seen as the most applicable consensus mechanism in blockchain-enabled wireless networks. However, previous studies on PBFT do not consider the channel performance of the physical layer, such as path loss and channel fading, resulting in research results that are far from real networks. Additionally, 6G communications will widely deploy high frequency signals such as millimeter wave (mmWave) and terahertz (THz), while the perfo…
Terahertz (THz) wireless access is considered as a next step towards sixth generation (6G) cellular systems. By utilizing even higher frequency bands than 5G millimeter wave (mmWave) New Radio (NR), they will operate over extreme bandwidth delivering unprecedented rates at the access interface. However, by relying upon pencil-wide beams, these systems will not only inherit mmWave propagation challenges such as blockage phenomenon but introduce their own issues associated with micromobility of user equipment (UE). In this paper, we analyze and compare user association schemes and multi-connecti…
This letter focuses on the secure transmission for an intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) and terahertz (THz) systems, in which a base station (BS) communicates with its destination via an IRS, in the presence of a passive eavesdropper. To maximize the system secrecy rate, the transmit beamforming at the BS and the reflecting matrix at the IRS are jointly optimized with transmit power and discrete phase-shift constraints. It is first proved that the beamforming design is independent of the phase shift design under the rank-one channel assumption. The formulat…
We propose a MIMO channel estimation method for millimeter-wave (mmWave) and terahertz (THz) systems based on frequency-selective atomic norm minimization (FS-ANM). For the strong line-of-sight property of the channel in such high-frequency bands, prior knowledge on the ranges of angles of departure/arrival (AoD/AoA) can be obtained as the prior knowledge, which can be exploited by the proposed channel estimator to improve the estimation accuracy. Simulation results show that the proposed method can achieve considerable performance gain when compared with the existing approaches without incorp…
Millimeter-wave (mmWave) and Terahertz (THz)-band communications exploit the abundant bandwidth to fulfill the increasing data rate demands of 6G wireless communications. To compensate for the high propagation loss with reduced hardware costs, ultra-massive multiple-input multiple-output (UM-MIMO) with a hybrid beamforming structure is a promising technology in the mmWave and THz bands. However, channel estimation (CE) is challenging for hybrid UM-MIMO systems, which requires recovering the high-dimensional channels from severely few channel observations. In this paper, a Pruned Approximate Me…
Intelligent reflecting surface (IRS) has emerged as a competitive solution to address blockage issues in millimeter wave (mmWave) and Terahertz (THz) communications due to its capability of reshaping wireless transmission environments. Nevertheless, obtaining the channel state information of IRS-assisted systems is quite challenging because of the passive characteristics of the IRS. In this paper, we consider the problem of beam training/alignment for IRS-assisted downlink mmWave/THz systems, where a multi-antenna base station (BS) with a hybrid structure serves a single-antenna user aided by …
The convergence of sensing and communication in the millimeter-wave (mmWave) and low terahertz (THz) bands has been envisioned as a promising technology, since it incorporates high-rate data transmission of hundreds of Gbps and mm-level radar sensing in a spectrum- and cost-efficient manner, by sharing both the frequency and hardware resources. However, the joint radar sensing and communication (JRC) system faces considerable challenges in the mmWave and low-THz scale, due to the peculiarities of the propagation channel and radio-frequency (RF) front ends. To this end, the waveform design for …
6G operators may use millimeter wave (mmWave) and sub-terahertz (sub-THz) bands to meet the ever-increasing demand for wireless access. Sub-THz communication comes with many existing challenges of mmWave communication and adds new challenges associated with the wider bandwidths, more antennas, and harsher propagations. Notably, the frequency- and spatial-wideband (dual-wideband) effects are significant at sub-THz. This paper presents a compressed training framework to estimate the time-varying sub-THz MIMO-OFDM channels. A set of frequency-dependent array response matrices are constructed, ena…
Vision-aided wireless communication is motivated by the recent advances in deep learning and computer vision as well as the increasing dependence on line-of-sight links in millimeter wave (mmWave) and terahertz systems. By leveraging vision, this new research direction enables an interesting set of new capabilities such as vision-aided mmWave beam and blockage prediction, proactive hand-off, and resource allocation among others. These capabilities have the potential of reliably supporting highly-mobile applications such as vehicular/drone communications and wireless virtual/augmented reality i…
Millimeter wave (mmWave) communication is one of the most promising technologies in fifth generation (5G) mobile networks due to its access to a large amount of available spectrum resources. Despite the theoretical potential of a high data rate, there are still several key technical challenges with using mmWave in mobile networks, such as severe pathloss, high penetration loss, narrow beamwidth, etc. Hence, accurate and reliable knowledge of mmWave channel propagation characteristics is essential for developing 5G wireless communication systems. In this article, the fundamental characteristics…
Mobility and blockage are two critical challenges in wireless transmission over millimeter-wave (mmWave) and Terahertz (THz) bands. In this paper, we investigate network massive multiple-input multiple-output (MIMO) transmission for mmWave/THz downlink in the presence of mobility and blockage. Considering the mmWave/THz propagation characteristics, we first propose to apply per-beam synchronization for network massive MIMO to mitigate the channel Doppler and delay dispersion effects. Accordingly, we establish a transmission model. We then investigate network massive MIMO downlink transmission …
In order to achieve terabits-per-second (Tbps) data rates in the sixth-generation (6G) mobile system, wireless communications are required to exploit the abundant spectrum in the millimeter-wave (mmWave) and terahertz (THz) bands. However, high-frequency transmission heavily relies on high beamforming gain to compensate for severe propagation loss. A beam-based system faces a barrier in the process of initial access, where a base station must broadcast synchronization signals and system information to all users within its coverage. Hence, this paper proposes a novel omnidirectional broadcastin…
DiffPace: Diffusion-based Plug-and-play Augmented Channel Estimation in mmWave and Terahertz Ultra-Massive MIMO Systems
Terahertz Wireless Communications (TWC) Laboratory, Shanghai Jiao Tong University（太赫兹无线通信实验室，上海交通大学）；Cooperative Medianet Innovation Center (CMIC), School of Information Science and Electronic Engineering, Shanghai Jiao Tong University（协作中位网创新中心（CMIC），信息科学与电子工程学院，上海交通大学）；Institute for Digital Communications, Friedrich-Alexander-Universität Erlangen-Nürnberg (FAU)（数字通信研究所，弗赖堡-亚历山大-大学埃尔朗根-纽伦堡（FAU））
Base station (BS) placement in mobile networks is critical to the efficient use of resources in any communication system and one of the main factors that determines the quality of communication. Although there is ample literature on the optimum placement of BSs for sub-6 GHz bands, channel propagation characteristics, such as penetration loss, are notably different in millimeter-wave (mmWave) bands than in sub-6 GHz bands. Therefore, designated solutions are needed for mmWave systems to have reliable quality of service (QoS) assessment. This article proposes a multi-armed bandit (MAB) learning…
In this paper, we present millimeter-wave (mmWave) penetration loss measurements and analysis at E-bands-73 GHz and 81 GHz. Penetration loss was measured for common building materials such as clear glass, metal, tinted glass, wood, and drywall on the campus of Boise State University in the city of Boise. A horn antenna with a gain of 24 dBi was used at the transmitter and receiver at both bands, and both antennas were boresight-aligned with respect to the test material. A total of twelve locations were selected to test five materials. We tested two indoor materials (clear glass and wood) in at…
Millimeter-wave (mmWave) and Terahertz (THz) will be used in the sixth-generation (6G) wireless systems, especially for indoor scenarios. This paper presents an indoor three-dimensional (3-D) statistical channel model for mmWave and sub-THz frequencies, which is developed from extensive channel propagation measurements conducted in an office building at 28 GHz and 140 GHz in 2014 and 2019. Over 15,000 power delay profiles (PDPs) were recorded to study channel statistics such as the number of time clusters, cluster delays, and cluster powers. All the parameters required in the channel generatio…
In the upcoming 5G communication, the millimeter-wave (mmWave) technology will play an important role due to its large bandwidth and high data rate. However, mmWave frequencies have higher free-space path loss (FSPL) in line-of-sight (LOS) propagation compared to the currently used sub-6 GHz frequencies. What is more, in non-line-of-sight (NLOS) propagation, the attenuation of mmWave is larger compared to the lower frequencies, which can seriously degrade the performance. It is therefore necessary to investigate mmWave propagation characteristics for a given deployment scenario to understand c…
With the increasing adoption of millimeter-waves (mmWave) over cellular networks, outdoor-to-indoor (O2I) communication has been one of the challenging research problems due to high penetration loss of buildings. To address this, we investigate the practicability of utilizing reconfigurable intelligent surfaces (RISs) for assisting such O2I communication. We propose a new notion of prefabricated RIS-empowered wall consisting of a large number of chipless radio frequency identification (RFID) sensors. Each sensor maintains its own bank of delay lines. These sensors which are built within the bu…
Millimeter-wave (mmWave) communication systems require narrow beams to increase communication range. If the dominant communication direction is blocked by an obstacle, an alternative and reliable spatial communication path should be quickly identified to maintain connectivity. In this paper, we introduce a new metric to quantify the effective multipath richness (EMR) of a directional communication channel by considering the strength and spatial diversity of the resolved paths, while also taking into account beamwidth and blockage characteristics. The metric is defined as a weighted sum of the …
The low hardware cost makes ultra-large (XL) reconfigurable intelligent surface (RIS) an attractive solution for the performance enhancement of localization and communication systems, but it results in near-field propagation channels, especially for the high-frequency communication systems, e.g. mmWave and sub-terahertz (subTHz) systems. This makes localization and channel estimation in the near field of the RIS-aided subTHz system more challenging. In this paper, we consider the spherical wavefront propagation in the near field of the subTHz system with the assistance of a RIS. A near-field c…
Employing large antenna arrays is a key characteristic of millimeter wave (mmWave) and terahertz communication systems. Due to the hardware constraints and the lack of channel knowledge, codebook based beamforming/combining is normally adopted to achieve the desired array gain. However, most of the existing codebooks focus only on improving the gain of their target user, without taking interference into account. This can incur critical performance degradation in dense networks. In this paper, we propose a sample-efficient online reinforcement learning based beam pattern design algorithm that l…
Accurate channel modeling and simulation are indispensable for millimeter-wave wideband communication systems that employ electrically-steerable and narrow beam antenna arrays. Three important channel modeling components, spatial consistency, human blockage, and outdoor-to-indoor penetration loss, were proposed in the 3rd Generation Partnership Project Release 14 for mmWave communication system design. This paper presents NYUSIM 2.0, an improved channel simulator which can simulate spatially consistent channel realizations based on the existing drop-based channel simulator NYUSIM 1.6.1. A geom…
This paper focuses on providing an analytical framework for the quantification and evaluation of the pointing error for a general case at high-frequency millimeter wave (mmWave) and terahertz (THz) communication links. For this aim, we first derive the the probability density function (PDF) and cumulative distribution functions (CDF) of the pointing error between an unstable transmitter (Tx) and receiver (Rx), that have different antenna patterns and for which the vibrations are not similar in the Yaw and Pitch directions. The special case where the Tx and Rx are both equipped with uniform lin…
Outdoor-to-indoor communications in millimeter-wave (mmWave) cellular networks have been one challenging research problem due to the severe attenuation and the high penetration loss caused by the propagation characteristics of mmWave signals. We propose a viable solution to implement the outdoor-to-indoor mmWave communication system with the aid of an active intelligent transmitting surface (active-ITS), where the active-ITS allows the incoming signal from an outdoor base station (BS) to pass through the surface and be received by the indoor user-equipments (UEs) after shifting its phase and m…
The University of Oxford（牛津大学）；Bogazici University（博阿齐奇大学）
Robust indoor ego-motion estimation has attracted significant interest in the last decades due to the fast-growing demand for location-based services in indoor environments. Among various solutions, frequency-modulated continuous-wave (FMCW) radar sensors in millimeter-wave (MMWave) spectrum are gaining more prominence due to their intrinsic advantages such as penetration capability and high accuracy. Single-chip low-cost MMWave radar as an emerging technology provides an alternative and complementary solution for robust ego-motion estimation, making it feasible in resource-constrained platfor…
Based on the vision on the 6G wireless communication network, i.e., global coverage, all spectrums and all applications, we comprehensively survey 6G related wireless channel measurements, channel characteristics, and channel models for all frequency bands and all scenarios. Millimeter wave (mmWave), terahertz (THz), optical band, satellite, unmanned aerial vehicle (UAV), maritime, underwater acoustic, high-speed train (HST), vehicle-to-vehicle (V2V), massive/ ultra-massive multiple-input multiple-output (MIMO), orbital angular momentum (OAM), and industry Internet of things (IoT) communicatio…
This paper provides an analysis of radio wave scattering for frequencies ranging from the microwave to the Terahertz band (e.g., 1 GHz - 1 THz), by studying the scattering power reradiated from various types of materials with different surface roughnesses. First, fundamentals of scattering and reflection are developed and explained for use in wireless mobile radio, and the effect of scattering on the reflection coefficient for rough surfaces is investigated. Received power is derived using two popular scattering models - the directive scattering (DS) model and the radar cross section (RCS) mod…
University of Trento（特伦托大学）；Lund University（隆德大学）；University of Padova（帕多瓦大学）
The commercial availability of low-cost millimeter wave (mmWave) communication and radar devices is starting to improve the penetration of such technologies in consumer markets, paving the way for large-scale and dense deployments in fifth-generation (5G)-and-beyond as well as 6G networks. At the same time, pervasive mmWave access will enable device localization and device-free sensing with unprecedented accuracy, especially with respect to sub-6 GHz commercial-grade devices. This paper surveys the state of the art in device-based localization and device-free sensing using mmWave communication…
The objective of the Enhanced Mobile Broadband use case in 5G networks is to deliver high capacity access to densely populated areas, like city centres, transportation hubs or convention centres. Millimetre-wave communications are the go-to technology to realise that objective, yet due to weak outdoor-to-indoor penetration, outdoor deployments will not suffice and dedicated indoor deployments will be necessary. In this article, we study dense deployments of millimetre-wave access points mounted on the ceiling, with directional antennas pointing downwards to illuminate selected spots on the gro…
Wireless communications over Terahertz (THz)-band frequencies are vital enablers of ultra-high rate applications and services in sixth-generation (6G) networks. However, THz communications suffer from poor coverage because of inherent THz features such as high penetration losses, severe path loss, and significant molecular absorption. To surmount these critical challenges and fully exploit the THz band, we explore a coexisting radio frequency (RF) and THz finite indoor network in which THz small cells are deployed to provide high data rates, and RF macrocells are deployed to satisfy coverage r…
In the US, people spend 87% of their time indoors and have an average of four connected devices per person (in 2020). As such, providing indoor coverage has always been a challenge but becomes even more difficult as carrier frequencies increase to mmWave and beyond. This paper investigates the outdoor and outdoor-indoor coverage of an urban network comparing globally standardized building penetration models and implementing models to corresponding scenarios. The glass used in windows of buildings in the grid plays a pivotal role in determining the outdoor-to-indoor propagation loss. For 28 GHz…
One of the critical challenges of operating with the terahertz or millimeter-wave wireless networks is the necessity of at least a strong non-line-of-sight (NLoS) reflected path to form a stable link. Recent studies have shown that an economical way of enhancing/improving these NLoS links is by using passive metallic reflectors that provide strong reflections. However, despite its inherent radio advantage, metals can dramatically influence the landscape's appearance - especially the indoor environment. A conceptual view of escaping this is by using transparent reflectors. In this work, for the…
Line-of-sight link blockages represent a key challenge for the reliability and latency of millimeter wave (mmWave) and terahertz (THz) communication networks. To address this challenge, this paper leverages mmWave and LiDAR sensory data to provide awareness about the communication environment and proactively predict dynamic link blockages before they occur. This allows the network to make proactive decisions for hand-off/beam switching, enhancing the network reliability and latency. More specifically, this paper addresses the following key questions: (i) Can we predict a line-of-sight link blo…
Remote Detection of Applications for Improved Beam Tracking in mmWave/sub-THz 5G/6G Systems
HSE University（高等经济大学）；Moscow Pedagogical State University（莫斯科国立师范大学）；Peoples’ Friendship University of Russia (RUDN University)（俄罗斯人民友谊大学（RUDN大学））；Russian Quantum Center（俄罗斯量子中心）
The next generations of wireless networks will work in frequency bands ranging from sub-6 GHz up to 100 GHz. Radio signal propagation differs here in several critical aspects from the behaviour in the microwave frequencies currently used. With wavelengths in the millimeter range (mmWave), both penetration loss and free-space path loss increase, while specular reflection will dominate over diffraction as an important propagation channel. Thus, current channel model protocols used for the generation of mobile networks and based on statistical parameter distributions obtained from measurements be…
