Accurate channel modeling and simulation are indispensable for millimeter-wave wideband communication systems that employ electrically-steerable and narrow beam antenna arrays. Three important channel modeling components, spatial consistency, human blockage, and outdoor-to-indoor penetration loss, were proposed in the 3rd Generation Partnership Project Release 14 for mmWave communication system design. This paper presents NYUSIM 2.0, an improved channel simulator which can simulate spatially consistent channel realizations based on the existing drop-based channel simulator NYUSIM 1.6.1. A geometry-based approach using multiple reflection surfaces is proposed to generate spatially correlated and time-variant channel coefficients. Using results from 73 GHz pedestrian measurements for human blockage, a four-state Markov model has been implemented in NYUSIM to simulate dynamic human blockage shadowing loss. To model the excess path loss due to penetration into buildings, a parabolic model for outdoor-to-indoor penetration loss has been adopted from the 5G Channel Modeling special interest group and implemented in NYUSIM 2.0. This paper demonstrates how these new modeling capabilities reproduce realistic data when implemented in Monte Carlo fashion using NYUSIM 2.0, making it a valuable measurement-based channel simulator for fifth-generation and beyond mmWave communication system design and evaluation.
Commonly used drop-based channel models cannot satisfy the requirements of spatial consistency for millimeter-wave (mmWave) channel modeling where transient motion or closely-spaced users need to be considered. A channel model having \textit{spatial consistency} can capture the smooth variations of channels, when a user moves, or when multiple users are close to each other in a local area within, say, 10 m in an outdoor scenario. Spatial consistency is needed to support the testing of beamforming and beam tracking for massive multiple-input and multiple-output (MIMO) and multi-user MIMO in fif…
This paper presents details and applications of a novel channel simulation software named NYUSIM, which can be used to generate realistic temporal and spatial channel responses to support realistic physical- and link-layer simulations and design for fifth-generation (5G) cellular communications. NYUSIM is built upon the statistical spatial channel model for broadband millimeter-wave (mmWave) wireless communication systems developed by researchers at New York University (NYU). The simulator is applicable for a wide range of carrier frequencies (500 MHz to 100 GHz), radio frequency (RF) bandwidt…
This paper describes an implementation of spatial consistency in the NYUSIM channel simulation platform. NYUSIM is a millimeter wave (mmWave) channel simulator that realizes measurement-based channel models based on a wide range of multipath channel parameters, including realistic multipath time delays and multipath components that arrive at different 3-D angles in space, and generates life-like samples of channel impulse responses (CIRs) that statistically match those measured in the real world. To properly simulate channel impairments and variations for adaptive antenna algorithms or channel…
Accurate channel modeling and simulation tools are vital for studying sub-THz and millimeter (mmWave) wideband communication system performance. To accurately design future high data rate, low latency wireless modems, the entire protocol stack must be appropriately modeled to understand how the physical layer impacts the end-to-end performance experienced by the end user. This paper presents a full stack end-to-end performance analysis in ns-3 using drop-based NYU channel model (NYUSIM) and 3GPP statistical channel model (SCM) in scenarios, namely urban microcell (UMi), urban macrocell (UMa), …
Line-of-sight link blockages represent a key challenge for the reliability and latency of millimeter wave (mmWave) and terahertz (THz) communication networks. This paper proposes to leverage LiDAR sensory data to provide awareness about the communication environment and proactively predict dynamic link blockages before they happen. This allows the network to make proactive decisions for hand-off/beam switching which enhances its reliability and latency. We formulate the LiDAR-aided blockage prediction problem and present the first real-world demonstration for LiDAR-aided blockage prediction in…
Blocking is one of the most important challenges in exploiting millimeter-wave for fifth-generation (5G) cellular communication systems. Compared to blockages caused by buildings or terrains, human body blockage exhibits a higher complexity due to the mobility and dynamic statistics of humans. To support development of outdoor millimeter-wave cellular systems, in this paper we present a novel 3D physical model of human body blockage. Based on the proposed model, the impact of human body blockage on frame-based data transmission is discussed, with respect to the system specifications and enviro…
Mobility may degrade the performance of next-generation vehicular networks operating at the millimeter-wave spectrum: frequent loss of alignment and blockages require repeated beam training and handover, thus incurring huge overhead. In this paper, an adaptive and joint design of beam training, data transmission and handover is proposed, that exploits the mobility process of mobile users and the dynamics of blockages to optimally trade-off throughput and power consumption. At each time slot, the serving base station decides to perform either beam training, data communication, or handover when …
Millimeter wave (mmWave) and sub-terahertz communication systems rely mainly on line-of-sight (LOS) links between the transmitters and receivers. The sensitivity of these high-frequency LOS links to blockages, however, challenges the reliability and latency requirements of these communication networks. In this paper, we propose to utilize radar sensors to provide sensing information about the surrounding environment and moving objects, and leverage this information to proactively predict future link blockages before they happen. This is motivated by the low cost of the radar sensors, their abi…
This paper investigates a novel research direction that leverages vision to help overcome the critical wireless communication challenges. In particular, this paper considers millimeter wave (mmWave) communication systems, which are principal components of 5G and beyond. These systems face two important challenges: (i) the large training overhead associated with selecting the optimal beam and (ii) the reliability challenge due to the high sensitivity to link blockages. Interestingly, most of the devices that employ mmWave arrays will likely also use cameras, such as 5G phones, self-driving vehi…
Mobility and blockage are two critical challenges in wireless transmission over millimeter-wave (mmWave) and Terahertz (THz) bands. In this paper, we investigate network massive multiple-input multiple-output (MIMO) transmission for mmWave/THz downlink in the presence of mobility and blockage. Considering the mmWave/THz propagation characteristics, we first propose to apply per-beam synchronization for network massive MIMO to mitigate the channel Doppler and delay dispersion effects. Accordingly, we establish a transmission model. We then investigate network massive MIMO downlink transmission …
Mobility may degrade the performance of next-generation vehicular networks operating at the millimeter-wave spectrum: frequent mis-alignment and blockages require repeated beam training and handover, and incur enormous overhead. Nevertheless, mobility induces temporal correlations in the communication beams and in blockage events. In this paper, an adaptive design of beam training, data transmission and handover is proposed, that learns and exploits these temporal correlations to reduce the beam training overhead and optimally trade-off throughput and power consumption. At each time-slot, the …
Blockage by the human hand/body is an important impairment in realizing practical millimeter wave wireless systems. Prior works on blockage modeling are either based on theoretical studies of double knife edge diffraction or its modifications, high-frequency simulations of electromagnetic effects, or measurements with experimental millimeter wave prototypes. While such studies are useful, they do not capture the form-factor constraints of user equipments (UEs). In this work, we study the impact of hand/body blockage with a UE at $28$ GHz built on Qualcomm's millimeter wave modem, antenna modul…
This paper presents 73 GHz human blockage measurements for a point-to-point link with a 5 m transmitter-receiver separation distance in an indoor environment, with a human that walked at a speed of approximately 1 m/s at a perpendicular orientation to the line between the transmitter and receiver, at various distances between them. The experiment measures the shadowing effect of a moving human body when using directional antennas at the transmitter and receiver for millimeter-wave radio communications. The measurements were conducted using a 500 Megachips-per-second wideband correlator channel…
Millimeter-wave (mmWave) offers high data rate and bandwidth for air-to-everything (A2X) communications including air-to-air, air-to-ground, and air-to-tower. MmWave communication in the A2X network is sensitive to buildings blockage effects. In this paper, we propose an analytical framework to define and characterise the connectivity for an aerial access point (AAP) by jointly using stochastic geometry and random shape theory. The buildings are modelled as a Boolean line-segment process with fixed height. The blocking area for an arbitrary building is derived and minimized by optimizing the a…
The densely packed antennas of millimeter-Wave (mmWave) MIMO systems are often blocked by the rain, snow, dust and even by fingers, which will change the channel's characteristics and degrades the system's performance. In order to solve this problem, we propose a cross-entropy inspired antenna array diagnosis detection (CE-AAD) technique by exploiting the correlations of adjacent antennas, when blockages occur at the transmitter. Then, we extend the proposed CE-AAD algorithm to the case, where blockages occur at transmitter and receiver simultaneously. Our simulation results show that the prop…
The radiation pattern of an antenna array depends on the excitation weights and the geometry of the array. Due to wind and atmospheric conditions, outdoor millimeter wave antenna elements are subject to full or partial blockages from a plethora of particles like dirt, salt, ice, and water droplets. Handheld devices are also subject to blockages from random finger placement and/or finger prints. These blockages cause absorption and scattering to the signal incident on the array, and change the array geometry. This distorts the far-field radiation pattern of the array leading to an increase in t…
There has been a growing interest in the commercialization of millimeter wave (mmW) technology as a part of the Fifth-Generation New Radio (5G-NR) wireless standardization efforts. In this direction, many sets of independent measurement campaigns show that wireless propagation at mmW carrier frequencies is only marginally worse than propagation at sub-6 GHz carrier frequencies for small-cell coverage --- one of the most important use-cases for 5G-NR. On the other hand, the biggest determinants of viability of mmW systems in practice are penetration and blockage of mmW signals through different…
The ongoing commercial deployment of millimeter wave systems brings into focus a number of practical issues in form factor user equipment (UE) design. With wavelengths becoming smaller, antenna gain patterns becoming directional, and link budgets critically dependent on beamforming, it becomes imperative to use a number of antenna modules at different locations of the UE for good performance. While more antennas/modules can enhance beamforming array gains, it comes with the tradeoff of higher component cost, power consumption of the associated radio frequency circuitry, and a beam management o…
Rapidly fading channels caused by pedestrians in dense urban environments will have a significant impact on millimeter-wave (mmWave) communications systems that employ electrically-steerable and narrow beamwidth antenna arrays. A peer-to-peer (P2P) measurement campaign was conducted with 7-degree, 15-degree, and 60-degree half-power beamwidth (HPBW) antenna pairs at 73.5 GHz and with 1 GHz of RF null-to-null bandwidth in a heavily populated open square scenario in Brooklyn, New York, to study blockage events caused by typical pedestrian traffic. Antenna beamwidths that range approximately an o…
Millimeter wave (mmWave) communications systems are promising candidate to support extremely high data rate services in future wireless networks. MmWave communications exhibit high penetration loss (blockage) and require directional transmissions to compensate for severe channel attenuations and for high noise powers. When blockage occurs, there are at least two simple prominent options: 1) switching to the conventional microwave frequencies (fallback option) and 2) using an alternative non-blocked path (relay option). However, currently it is not clear under which conditions and network param…
Intelligent reflecting surface (IRS) offers a cost effective solution to link blockage problem in mmWave communications, and the prerequisite of which is the accurate estimation of (1) the optimal beams for base station/access point (BS/AP) and mobile terminal (MT), (2) the optimal reflection patterns for IRSs, and (3) link blockage. In this paper, we carry out beam training design for IRSs assisted mmWave communications to estimate the aforementioned parameters. To acquire the optimal beams and reflection patterns, we firstly perform random beamforming and maximum likelihood estimation to est…
Millimeter-wave (mmWave) and Terahertz (THz) will be used in the sixth-generation (6G) wireless systems, especially for indoor scenarios. This paper presents an indoor three-dimensional (3-D) statistical channel model for mmWave and sub-THz frequencies, which is developed from extensive channel propagation measurements conducted in an office building at 28 GHz and 140 GHz in 2014 and 2019. Over 15,000 power delay profiles (PDPs) were recorded to study channel statistics such as the number of time clusters, cluster delays, and cluster powers. All the parameters required in the channel generatio…
A critical challenge for wireless communications in the millimeter wave (mmWave) bands is blockage. MmWave signals suffer significant penetration losses from many common materials and objects, and small changes in the position of obstacles in the environment can cause large variations in the channel quality. This paper provides a measurement-based study of the effects of human blockage on an end-to-end application over a mmWave cellular link. A phased array system is used to measure the channel in multiple directions almost simultaneously in a realistic indoor scenario. The measurements are in…
Unlocking the full potential of millimeter-wave and sub-terahertz wireless communication networks hinges on realizing unprecedented low-latency and high-reliability requirements. The challenge in meeting those requirements lies partly in the sensitivity of signals in the millimeter-wave and sub-terahertz frequency ranges to blockages. One promising way to tackle that challenge is to help a wireless network develop a sense of its surrounding using machine learning. This paper attempts to do that by utilizing deep learning and computer vision. It proposes a novel solution that proactively predic…
Millimeter wave (mmWave) technologies have the potential to achieve very high data rates, but suffer from intermittent connectivity. In this paper, we provision an architecture to integrate sub-6 GHz and mmWave technologies, where we incorporate the sub-6 GHz interface as a fallback data transfer mechanism to combat blockage and intermittent connectivity of the mmWave communications. To this end, we investigate the problem of scheduling data packets across the mmWave and sub-6 GHz interfaces such that the average delay of system is minimized. This problem can be formulated as Markov Decision P…
Due to its potential to support high data rates at low latency with reasonable interference isolation, millimeter-wave (mmWave) communications has emerged as a promising solution for wireless personal-area networks (WPAN) and an enabler for emerging applications such as high-resolution untethered virtual reality. At mmWave, signals are prone to blockage by objects in the environment, including human bodies. Most mmWave systems utilize directional antennas in order to overcome the significant path loss. In this paper, we consider the effects of blockage and antenna directivity on the performanc…
The sensitivity of millimeter wave (mmWave) signals to blockages is a fundamental challenge for mobile mmWave communication systems. The sudden blockage of the line-of-sight (LOS) link between the base station and the mobile user normally leads to disconnecting the communication session, which highly impacts the system reliability. Further, reconnecting the user to another LOS base station incurs high beam training overhead and critical latency problems. In this paper, we leverage machine learning tools and propose a novel solution for these reliability and latency challenges in mmWave MIMO sy…
Future railway is expected to accommodate both train operation services and passenger broadband services. The millimeter wave (mmWave) communication is a promising technology in providing multi-gigabit data rates to onboard users. However, mmWave communications suffer from severe propagation attenuation and vulnerability to blockage, which can be very challenging in high-speed railway (HSR) scenarios. In this paper, we investigate efficient hybrid beamforming (HBF) design for train-to-ground communications. First, we develop a two-stage HBF algorithm in blockage-free scenarios. In the first st…
In future wireless networks, one of the use-cases of interest is Internet-of-vehicles (IoV). Here, IoV refers to two different functionalities, namely, serving the in-vehicle users and supporting the connected-vehicle functionalities, where both can be well provided by the transceivers installed on top of vehicles. Such dual functionality of on-vehicle transceivers implies strict rate and reliability requirements, for which one may need to communicate at millimeter wave (mmW) frequencies. However, IoV communication at mmW requires up-to-date channel state information (CSI) and blockage avoidan…
Multi-cell wireless systems usually suffer both intra-cell and inter-cell interference, which can be mitigated via coordinated multipoint (CoMP) techniques. Previous works on multi-cell analysis for the microwave band generally consider fully digital beamforming that requires a complete radio-frequency chain behind each antenna, which is less practical for millimeter-wave (mmWave) systems where large amounts of antennas are necessary to provide sufficient beamforming gain and to enable transmission and reception of multiple data streams per user. This paper proposes four analog and digital hyb…
With the explosive growth of mobile data, the demand of high-speed railway (HSR) passengers for broadband wireless access services urgently needs the support of ultra-highspeed scenario broadband wireless communication. Millimeterwave (mmWave) can achieve high data transmission rates, but it is accompanied by high propagation loss and vulnerability to blockage. To address this issue, developments of directional antennas and unmanned aerial vehicles (UAVs) enhance the robustness of the mmWave train-ground communication system. In this paper, we propose a UAV and MRs relay assistance (UMRA) algo…
To support high data rate urgent or ad hoc communications, we consider mmWave UAV cellular networks and the associated challenges and solutions. To enable fast beamforming training and tracking, we first investigate a hierarchical structure of beamforming codebooks and design of hierarchical codebooks with different beam widths via the sub-array techniques. We next examine the Doppler effect as a result of UAV movement and find that the Doppler effect may not be catastrophic when high gain directional transmission is used. We further explore the use of millimeter wave spatial division multiple…
Multiple-input multiple-output (MIMO) systems are well suited for millimeter-wave (mmWave) wireless communications where large antenna arrays can be integrated in small form factors due to tiny wavelengths, thereby providing high array gains while supporting spatial multiplexing, beamforming, or antenna diversity. It has been shown that mmWave channels exhibit sparsity due to the limited number of dominant propagation paths, thus compressed sensing techniques can be leveraged to conduct channel estimation at mmWave frequencies. This paper presents a novel approach of constructing beamforming d…
In this paper, a new mathematical framework to the analysis of millimeter wave cellular networks is introduced. Its peculiarity lies in considering realistic path-loss and blockage models, which are derived from recently reported experimental data. The path-loss model accounts for different distributions of line-of-sight and non-line-of-sight propagation conditions and the blockage model includes an outage state that provides a better representation of the outage possibilities of millimeter wave communications. By modeling the locations of the base stations as points of a Poisson point process…
Predicting the millimeter wave (mmWave) beams and blockages using sub-6GHz channels has the potential of enabling mobility and reliability in scalable mmWave systems. These gains attracted increasing interest in the last few years. Prior work, however, has focused on extracting spatial channel characteristics at the sub-6GHz band first and then use them to reduce the mmWave beam training overhead. This approach has a number of limitations: (i) It still requires a beam search at mmWave, (ii) its performance is sensitive to the error associated with extracting the sub-6GHz channel characteristic…
Many operators have been bullish on the role of millimeter-wave (mmWave) communications in fifth-generation (5G) mobile broadband because of its capability of delivering extreme data speeds and capacity. However, mmWave comes with challenges related to significantly high path loss and susceptibility to blockage. Particularly, when mmWave communication is applied to a mobile terminal device, communication can be frequently broken because of rampant hand blockage. Although a number of mobile phone companies have suggested configuring multiple sets of antenna modules at different locations on a m…
This paper develops a stochastic geometry-based approach for the modeling and analysis of finite millimeter wave (mmWave) wireless networks where a random number of transmitters and receivers are randomly located inside a finite region. We consider a selection strategy to serve a reference receiver by the transmitter providing the maximum average received power among all transmitters. Considering the unique features of mmWave communications such as directional transmit and receive beamforming and having different channels for line-of-sight (LOS) and non-line-of-sight (NLOS) links according to …
In this paper, a new mathematical framework to the analysis of millimeter wave cellular networks is introduced. Its peculiarity lies in considering realistic path-loss and blockage models, which are derived from experimental data recently reported in the literature. The path-loss model accounts for different distributions for line-of-sight and non-line-of-sight propagation conditions and the blockage model includes an outage state that provides a better representation of the outage possibilities of millimeter wave communications. By modeling the locations of the base stations as points of a Po…
Millimeter-wave (mmWave) and sub-Terahertz (THz) frequencies are expected to play a vital role in 6G wireless systems and beyond due to the vast available bandwidth of many tens of GHz. This paper presents an indoor 3-D spatial statistical channel model for mmWave and sub-THz frequencies based on extensive radio propagation measurements at 28 and 140 GHz conducted in an indoor office environment from 2014 to 2020. Omnidirectional and directional path loss models and channel statistics such as the number of time clusters, cluster delays, and cluster powers were derived from over 15,000 measured…
Millimeter-wave (mmWave) communication opens up tens of giga-hertz (GHz) spectrum in the mmWave band for use by next-generation wireless systems, thereby solving the problem of spectrum scarcity. Maintaining connectivity stands out to be a key design challenge for mmWave networks deployed in urban regions due to the blockage effect characterizing mmWave propagation. Specifically, mmWave signals can be blocked by buildings and other large urban objects. In this paper, we set out to investigate the blockage effect on the connectivity of mmWave networks in a Manhattan-type urban region modeled us…
Millimeter wave (mmWave) signals are much more sensitive to blockage, which results in a significant increase of the outage probability, especially for the users at the edge of the cells. In this paper, we exploit the technique of base station (BS) cooperation to improve the performance of the cell-edge users in the downlink transmission of mmWave cellular networks. We design two cooperative schemes, which are referred to as fixed-number BS cooperation (FNC) scheme and fixed-region BS cooperation (FRC) scheme, respectively. In FNC scheme, the cooperative BSs consist of the M nearest BSs around…
Millimeter-wave (mmWave) cellular systems are power-limited and susceptible to blockages. As a result, mmWave connectivity will be likely to be intermittent. One promising approach to increasing mmWave connectivity and range is to use relays. Device-to-device (D2D) communications open the door to the vast opportunities of D2D and device-to-network relaying for mmWave cellular systems. In this correspondence, we study how to select a good relay for a given source-destination pair in a two-hop mmWave cellular system, where the mmWave links are subject to random Bernoulli blockages. In such a sys…
Millimeter wave (mmW) communication is a promising solution for providing high-capacity wireless network access. However, the benefits of mmW are limited by the fact that the channel between a mmW access point and the user equipment can stochastically change due to severe blockage of mmW links by obstacles such as the human body. Thus, one main challenge of mmW network coverage is to enable directional line-of-sight links between access points and mobile devices. In this paper, a novel framework is proposed for optimizing mmW network coverage within hotspots and in-venue regions, while being c…
In this paper, we study the performance of millimeter wave (mmWave) vehicular communications (VCs) using non-orthogonal multiple access scheme (NOMA) at road intersections, since there areas are more prone to accidents. We study the case when the intersection involves two perpendicular lanes, we then extend the study to an intersection with several lanes. The transmission occurs between a source, and two destinations. The transmission experiences interference originated from a set of vehicles that are distributed as a Poisson point process (PPP). Our analysis includes the effects of blockage f…
Millimeter-wave multi-input multi-output (mm-Wave MIMO) systems are one of the candidate schemes for 5G wireless standardization efforts. In this context, the main contributions of this article are three-fold. 1) We describe parallel sets of measurements at identical transmit-receive location pairs with 2.9, 29 and 61 GHz carrier frequencies in indoor office, shopping mall, and outdoor settings. These measurements provide insights on propagation, blockage and material penetration losses, and the key elements necessary in system design to make mm-Wave systems viable in practice. 2) One of these…
The sensitivity of millimeter-wave (mmWave) radio channel to blockage is a fundamental challenge in achieving low-latency and ultra-reliable connectivity. In this paper, we explore the viability of using coordinated multi-point (CoMP) transmission for a delay bounded and reliable mmWave communication. We propose a novel blockage-aware algorithm for the sum-power minimization problem under the user-specific latency requirements in a dynamic mobile access network. We use the Lyapunov optimization framework, and provide a dynamic control algorithm, which efficiently transforms a time-average stoc…
Millimeter wave (mmWave) holds promise as a carrier frequency for fifth generation cellular networks. Because mmWave signals are sensitive to blockage, prior models for cellular networks operated in the ultra high frequency (UHF) band do not apply to analyze mmWave cellular networks directly. Leveraging concepts from stochastic geometry, this paper proposes a general framework to evaluate the coverage and rate performance in mmWave cellular networks. Using a distance-dependent line-of-site (LOS) probability function, the locations of the LOS and non-LOS base stations are modeled as two indepen…
The millimeter wave (mmWave) frequencies are likely to play a significant role in fifth-generation (5G) cellular systems. A key challenge in developing systems in these bands is the potential for rapid channel dynamics: since mmWave signals are blocked by many materials, small changes in the position or orientation of the handset relative to objects in the environment can cause large swings in the channel quality. This paper addresses the issue of tracking the signal to noise ratio (SNR), which is an essential procedure for rate prediction, handover and radio link failure detection. A simple m…
This paper investigates the coexistence between two key enabling technologies for the fifth generation (5G) mobile networks, non-orthogonal multiple access (NOMA) and millimeter-wave (mmWave) communications. Particularly, the application of random beamforming to the addressed mmWave-NOMA scenario is considered in this paper, in order to avoid the requirement that the base station knows all the users' channel state information. Stochastic geometry is used to characterize the performance of the proposed mmWave-NOMA transmission scheme, by using the key features of mmWave systems, e.g., mmWave tr…
The millimeter wave (mmWave) band has the potential to provide high throughput among wearable devices. When mmWave wearable networks are used in crowded environments, such as on a bus or train, antenna directivity and orientation hold the key to achieving Gbps rates. Previous work using stochastic geometry often assumes an infinite number of interfering nodes drawn from a Poisson Point Process (PPP). Since indoor wearable networks will be isolated due to walls, a network with a finite number of nodes may be a more suitable model. In this paper, we characterize the significant sources of interf…
The coverage probability of a user in a mmwave system depends on the availability of line-of-sight paths or reflected paths from any base station. Many prior works modelled blockages using random shape theory and analyzed the SIR distribution with and without interference. While, it is intuitive that the reflected paths do not significantly contribute to the coverage (because of longer path lengths), there are no works which provide a model and study the coverage with reflections. In this paper, we model and analyze the impact of reflectors using stochastic geometry. We observe that the reflec…
Recent researches show that millimeter wave (mmWave) communications can offer orders of magnitude increases in the cellular capacity. However, the secrecy performance of a mmWave cellular network has not been investigated so far. Leveraging the new path-loss and blockage models for mmWave channels, which are significantly different from the conventional microwave channel, this paper comprehensively studies the network-wide physical layer security performance of the downlink transmission in a mmWave cellular network under a stochastic geometry framework. We first study the secure connectivity p…
Millimeter-wave (mmWave) communication systems rely on large-scale antenna arrays to combat large path-loss at mmWave band. Due to hardware characteristics and deployment environments, mmWave large-scale antenna systems are vulnerable to antenna element blockages and failures, which necessitate diagnostic techniques to locate faulty antenna elements for calibration purposes. Current diagnostic techniques require full or partial knowledge of channel state information (CSI), which can be challenging to acquire in the presence of antenna failures. In this letter, we propose a blind diagnostic tec…
Millimetre wave (mm-wave) communication is considered as one of the most important enablers for the fifth generation communication (5G) system to support data rate of Gbps and above. In some scenarios, it is crucial to maintain a line of sight (LOS) link for users enjoying 5G immersive experiences and thus requiring very high data rate. In this paper, we investigate the LOS probability in mm-wave systems. In particular, we study the impact of access point (AP) and blockage height on the LOS probability and propose a solution to effectively enhance the LOS coverage by using high-rise APs on top…
With the severe spectrum shortage in conventional cellular bands, millimeter-wave (mmWave) frequencies have been attracting growing attention for next-generation micro- and picocellular wireless networks. A fundamental and open question is whether mmWave cellular networks are likely to be noise- or interference-limited. Identifying in which regime a network is operating is critical for the design of MAC and physical-layer procedures and to provide insights on how transmissions across cells should be coordinated to cope with interference. This work uses the latest measurement-based statistical …
With the severe spectrum shortage in conventional cellular bands, the millimeter (mmWave) frequencies, roughly above 10~GHz, have been attracting growing attention for next-generation micro- and pico- cellular wireless networks. A fundamental and open question is how these bands should be used by cellular operators. Cellular spectrum has been traditionally allocated following an exclusive ownership model. However, in this paper we argue that the distinct nature of mmWave communication -- the massive bandwidth degrees of freedom, directional isolation and high susceptibility to blockage -- sugg…
