There has been a growing interest in the commercialization of millimeter wave (mmW) technology as a part of the Fifth-Generation New Radio (5G-NR) wireless standardization efforts. In this direction, many sets of independent measurement campaigns show that wireless propagation at mmW carrier frequencies is only marginally worse than propagation at sub-6 GHz carrier frequencies for small-cell coverage --- one of the most important use-cases for 5G-NR. On the other hand, the biggest determinants of viability of mmW systems in practice are penetration and blockage of mmW signals through different materials in the scattering environment. With this background, the focus of this paper is on understanding the impact of blockage of mmW signals and reduced spatial coverage due to penetration through the human hand, body, vehicles, etc. Leveraging measurements with a 28 GHz mmW experimental prototype and electromagnetic simulation studies, we first propose statistical blockage models to capture the impact of the hand, human body and vehicles. We then study the time-scales at which mmW signals are disrupted by blockage (hand and human body). Our results show that these events can be attributed to physical movements and the time-scales corresponding to blockage are hence on the order of a few 100 ms or more. Building on this fundamental understanding, we finally consider the broader question of robustness of mmW beamforming to handle blockage. Network densification, subarray switching in a user equipment (UE) designed with multiple subarrays, fall back mechanisms such as codebook enhancements and switching to legacy carriers in non-standalone deployments, etc. can address blockage before it leads to a deleterious impact on the mmW link margin.
Blocking is one of the most important challenges in exploiting millimeter-wave for fifth-generation (5G) cellular communication systems. Compared to blockages caused by buildings or terrains, human body blockage exhibits a higher complexity due to the mobility and dynamic statistics of humans. To support development of outdoor millimeter-wave cellular systems, in this paper we present a novel 3D physical model of human body blockage. Based on the proposed model, the impact of human body blockage on frame-based data transmission is discussed, with respect to the system specifications and enviro…
Hand blockage leads to significant performance impairments at millimeter wave carrier frequencies. A number of prior works have characterized the loss in signal strength with the hand using studies with horn antennas and form-factor user equipments (UEs). However, the impact of the hand on the effective phase response seen by the antenna elements has not been studied so far. Towards this goal, we consider a measurement framework that uses a hand phantom holding the UE in relaxed positions reflective of talk mode, watching videos, and playing games. We first study the impact of blockage on a di…
This paper presents 73 GHz human blockage measurements for a point-to-point link with a 5 m transmitter-receiver separation distance in an indoor environment, with a human that walked at a speed of approximately 1 m/s at a perpendicular orientation to the line between the transmitter and receiver, at various distances between them. The experiment measures the shadowing effect of a moving human body when using directional antennas at the transmitter and receiver for millimeter-wave radio communications. The measurements were conducted using a 500 Megachips-per-second wideband correlator channel…
Future railway is expected to accommodate both train operation services and passenger broadband services. The millimeter wave (mmWave) communication is a promising technology in providing multi-gigabit data rates to onboard users. However, mmWave communications suffer from severe propagation attenuation and vulnerability to blockage, which can be very challenging in high-speed railway (HSR) scenarios. In this paper, we investigate efficient hybrid beamforming (HBF) design for train-to-ground communications. First, we develop a two-stage HBF algorithm in blockage-free scenarios. In the first st…
Millimeter-wave (mmWave) offers high data rate and bandwidth for air-to-everything (A2X) communications including air-to-air, air-to-ground, and air-to-tower. MmWave communication in the A2X network is sensitive to buildings blockage effects. In this paper, we propose an analytical framework to define and characterise the connectivity for an aerial access point (AAP) by jointly using stochastic geometry and random shape theory. The buildings are modelled as a Boolean line-segment process with fixed height. The blocking area for an arbitrary building is derived and minimized by optimizing the a…
The radiation pattern of an antenna array depends on the excitation weights and the geometry of the array. Due to wind and atmospheric conditions, outdoor millimeter wave antenna elements are subject to full or partial blockages from a plethora of particles like dirt, salt, ice, and water droplets. Handheld devices are also subject to blockages from random finger placement and/or finger prints. These blockages cause absorption and scattering to the signal incident on the array, and change the array geometry. This distorts the far-field radiation pattern of the array leading to an increase in t…
Line-of-sight link blockages represent a key challenge for the reliability and latency of millimeter wave (mmWave) and terahertz (THz) communication networks. This paper proposes to leverage LiDAR sensory data to provide awareness about the communication environment and proactively predict dynamic link blockages before they happen. This allows the network to make proactive decisions for hand-off/beam switching which enhances its reliability and latency. We formulate the LiDAR-aided blockage prediction problem and present the first real-world demonstration for LiDAR-aided blockage prediction in…
The ongoing commercial deployment of millimeter wave systems brings into focus a number of practical issues in form factor user equipment (UE) design. With wavelengths becoming smaller, antenna gain patterns becoming directional, and link budgets critically dependent on beamforming, it becomes imperative to use a number of antenna modules at different locations of the UE for good performance. While more antennas/modules can enhance beamforming array gains, it comes with the tradeoff of higher component cost, power consumption of the associated radio frequency circuitry, and a beam management o…
Rapidly fading channels caused by pedestrians in dense urban environments will have a significant impact on millimeter-wave (mmWave) communications systems that employ electrically-steerable and narrow beamwidth antenna arrays. A peer-to-peer (P2P) measurement campaign was conducted with 7-degree, 15-degree, and 60-degree half-power beamwidth (HPBW) antenna pairs at 73.5 GHz and with 1 GHz of RF null-to-null bandwidth in a heavily populated open square scenario in Brooklyn, New York, to study blockage events caused by typical pedestrian traffic. Antenna beamwidths that range approximately an o…
Mobility may degrade the performance of next-generation vehicular networks operating at the millimeter-wave spectrum: frequent loss of alignment and blockages require repeated beam training and handover, thus incurring huge overhead. In this paper, an adaptive and joint design of beam training, data transmission and handover is proposed, that exploits the mobility process of mobile users and the dynamics of blockages to optimally trade-off throughput and power consumption. At each time slot, the serving base station decides to perform either beam training, data communication, or handover when …
Millimeter wave (mmWave) communications systems are promising candidate to support extremely high data rate services in future wireless networks. MmWave communications exhibit high penetration loss (blockage) and require directional transmissions to compensate for severe channel attenuations and for high noise powers. When blockage occurs, there are at least two simple prominent options: 1) switching to the conventional microwave frequencies (fallback option) and 2) using an alternative non-blocked path (relay option). However, currently it is not clear under which conditions and network param…
Millimeter wave (mmWave) and sub-terahertz communication systems rely mainly on line-of-sight (LOS) links between the transmitters and receivers. The sensitivity of these high-frequency LOS links to blockages, however, challenges the reliability and latency requirements of these communication networks. In this paper, we propose to utilize radar sensors to provide sensing information about the surrounding environment and moving objects, and leverage this information to proactively predict future link blockages before they happen. This is motivated by the low cost of the radar sensors, their abi…
A critical challenge for wireless communications in the millimeter wave (mmWave) bands is blockage. MmWave signals suffer significant penetration losses from many common materials and objects, and small changes in the position of obstacles in the environment can cause large variations in the channel quality. This paper provides a measurement-based study of the effects of human blockage on an end-to-end application over a mmWave cellular link. A phased array system is used to measure the channel in multiple directions almost simultaneously in a realistic indoor scenario. The measurements are in…
This paper investigates a novel research direction that leverages vision to help overcome the critical wireless communication challenges. In particular, this paper considers millimeter wave (mmWave) communication systems, which are principal components of 5G and beyond. These systems face two important challenges: (i) the large training overhead associated with selecting the optimal beam and (ii) the reliability challenge due to the high sensitivity to link blockages. Interestingly, most of the devices that employ mmWave arrays will likely also use cameras, such as 5G phones, self-driving vehi…
Accurate channel modeling and simulation are indispensable for millimeter-wave wideband communication systems that employ electrically-steerable and narrow beam antenna arrays. Three important channel modeling components, spatial consistency, human blockage, and outdoor-to-indoor penetration loss, were proposed in the 3rd Generation Partnership Project Release 14 for mmWave communication system design. This paper presents NYUSIM 2.0, an improved channel simulator which can simulate spatially consistent channel realizations based on the existing drop-based channel simulator NYUSIM 1.6.1. A geom…
Beamforming is indispensable in the operation of 60-GHz millimeter-wave directional multi-gigabit Wi-Fi. Simple power method and its extensions enable the transmitting and receiving antenna arrays to form a beam for single spatial stream. To further improve the spectral efficiency in future 60-GHz directional Wi-Fi, alternating least square (ALS) algorithm can form multiple beams between the transmitter and receiver for multi-input-multi-output (MIMO) operations. For both shared and split MIMO architecture, the ALS beamforming algorithm can be operated in both frequency-flat and frequency-sele…
Due to its potential to support high data rates at low latency with reasonable interference isolation, millimeter-wave (mmWave) communications has emerged as a promising solution for wireless personal-area networks (WPAN) and an enabler for emerging applications such as high-resolution untethered virtual reality. At mmWave, signals are prone to blockage by objects in the environment, including human bodies. Most mmWave systems utilize directional antennas in order to overcome the significant path loss. In this paper, we consider the effects of blockage and antenna directivity on the performanc…
This letter investigates the hybrid analog and digital beamforming (HBF) design for multiuser millimeter wave (mmWave) communication systems based on the minimum mean square error (MMSE) criterion. Using the alternating minimization method, the hybrid precoder of the base station (BS) and the hybrid combiners of the users are alternatively optimized. It is shown that both the optimized digital precoder of the BS and the digital combiners of the users have closed-form expressions, and their corresponding analog ones can be efficiently obtained via generalized eigen-decomposition. Simulation res…
Mobility and blockage are two critical challenges in wireless transmission over millimeter-wave (mmWave) and Terahertz (THz) bands. In this paper, we investigate network massive multiple-input multiple-output (MIMO) transmission for mmWave/THz downlink in the presence of mobility and blockage. Considering the mmWave/THz propagation characteristics, we first propose to apply per-beam synchronization for network massive MIMO to mitigate the channel Doppler and delay dispersion effects. Accordingly, we establish a transmission model. We then investigate network massive MIMO downlink transmission …
Millimeter wave (mmWave) technologies have the potential to achieve very high data rates, but suffer from intermittent connectivity. In this paper, we provision an architecture to integrate sub-6 GHz and mmWave technologies, where we incorporate the sub-6 GHz interface as a fallback data transfer mechanism to combat blockage and intermittent connectivity of the mmWave communications. To this end, we investigate the problem of scheduling data packets across the mmWave and sub-6 GHz interfaces such that the average delay of system is minimized. This problem can be formulated as Markov Decision P…
Mobility may degrade the performance of next-generation vehicular networks operating at the millimeter-wave spectrum: frequent mis-alignment and blockages require repeated beam training and handover, and incur enormous overhead. Nevertheless, mobility induces temporal correlations in the communication beams and in blockage events. In this paper, an adaptive design of beam training, data transmission and handover is proposed, that learns and exploits these temporal correlations to reduce the beam training overhead and optimally trade-off throughput and power consumption. At each time-slot, the …
Blockage by the human hand/body is an important impairment in realizing practical millimeter wave wireless systems. Prior works on blockage modeling are either based on theoretical studies of double knife edge diffraction or its modifications, high-frequency simulations of electromagnetic effects, or measurements with experimental millimeter wave prototypes. While such studies are useful, they do not capture the form-factor constraints of user equipments (UEs). In this work, we study the impact of hand/body blockage with a UE at $28$ GHz built on Qualcomm's millimeter wave modem, antenna modul…
In millimeter-wave communications (MMWC), in order to compensate for high propagation attenuation, phased arrays are favored to achieve array gain by beamforming, where transmitting and receiving antenna arrays need to be jointly trained to obtain appropriate antenna weight vectors (AWVs). Since the amplitude of each element of the AWV is usually constraint constant to simplify the design of phased arrays in MMWC, the existing singular vector based beamforming training scheme cannot be used for such devices. Thus, in this letter, a steering vector based iterative beamforming training scheme, w…
Finite resolution analog beamforming (FRAB) has been recognized as an effective approach to reduce hardware costs in massive multiple-input multiple-output (MIMO) and millimeter-wave networks. However, the use of FRAB means that the beamformers are not perfectly aligned with the users' channels and multiple users may be assigned similar or even identifical beamformers. This letter shows how non-orthogonal multiple access (NOMA) can be used to exploit this feature of FRAB, where a single FRAB based beamformer is shared by multiple users. Both analytical and simulation results are provided to de…
Hybrid beamforming is a promising concept to achieve high data rate transmission at millimeter waves. To implement it in a transceiver, many references optimally adapt to a high-dimensional multi-antenna channel but more or less ignore the complexity of the channel estimation. Realizing that received coupling coefficients of the channel and pairs of possible analog beamforming vectors can be used for analog beam selection, we further propose a low-complexity scheme that exploits the coupling coefficients to implement hybrid beamforming. Essentially, the coupling coefficients can be regarded as…
Demonstrating the feasibility of large antenna array beamforming is essential for realizing mmWave communication systems. This is due to the dependency of these systems on the large array beamforming gains to provide sufficient received signal power. In this paper, the design of a proof-of-concept prototype that demonstrates these gains in practice is explained in detail. We develop a mmWave system with digitally controlled analog front-end. The developed prototype uses 60 GHz phased arrays and universal software radio peripheral (USRP) controllers. The software interface of our design is easi…
This paper proposed new hybrid, analog-digital, beamforming for a multiuser millimeter wave (mm-wave) relay system. For this system, we consider a sum rate maximization problem. The proposed hybrid beamforming is designed indirectly by considering a sum mean square error (MSE) minimization problem while utilizing the solution of digital beamforming. To this end, we assume that the digital beamforming utilizes the well known block diagonalization (BD) approach. Under this assumption, we solve our problem as follows: First, we formulate the sum rate maximization problem as the minimization of th…
Millimeter wave (mmWave) spectrum has drawn attention due to its tremendous available bandwidth. The high propagation losses in the mmWave bands necessitate beamforming with a large number of antennas. Traditionally each antenna is paired with a high-speed analog-to-digital converter (ADC), which results in high power consumption. A hybrid beamforming architecture and one-bit resolution ADCs have been proposed to reduce power consumption. However, analog beamforming and one-bit quantization make channel estimation more challenging. In this paper, we propose a narrowband channel estimation algo…
In this paper, we investigate an intelligent reflecting surface (IRS)-assisted millimeter-wave multiple-input single-output downlink wireless communication system. By jointly calculating the active beamforming at the base station and the passive beamforming at the IRS, we aim to minimize the transmit power under the constraint of each user' signal-to-interference-plus-noise ratio. To solve this problem, we propose a low-complexity machine learning-based cross-entropy (CE) algorithm to alternately optimize the active beamforming and the passive beamforming. Specifically, in the alternative iter…
Multi-cell wireless systems usually suffer both intra-cell and inter-cell interference, which can be mitigated via coordinated multipoint (CoMP) techniques. Previous works on multi-cell analysis for the microwave band generally consider fully digital beamforming that requires a complete radio-frequency chain behind each antenna, which is less practical for millimeter-wave (mmWave) systems where large amounts of antennas are necessary to provide sufficient beamforming gain and to enable transmission and reception of multiple data streams per user. This paper proposes four analog and digital hyb…
For millimeter-wave (mmWave) massive MIMO systems, the codebook-based analog beamforming (including transmit precoding and receive combining) is usually used to compensate the severe attenuation of mmWave signals. However, conventional beamforming schemes involve complicated search among pre-defined codebooks to find out the optimal pair of analog precoder and analog combiner. To solve this problem, by exploring the idea of turbo equalizer together with tabu search (TS) algorithm, we propose a Turbo-like beamforming scheme based on TS, which is called Turbo-TS beamforming in this paper, to ach…
This paper develops a location based analog beamforming (BF) technique using compressive sensing (CS) to be feasible for millimeter wave (mmWave) wireless communication systems. The proposed scheme is based on exploiting the benefits of CS and localization to reduce mmWave beamforming (BF) complexity and enhance its performance compared with conventional mmWave analog BF techniques. CS theory is used to exploit the sparse nature of the mmWave propagation channel to estimate both the angle of departures (AoDs) and the angle of arrivals (AoAs) of the mmWave channel, and knowing the node location…
The densely packed antennas of millimeter-Wave (mmWave) MIMO systems are often blocked by the rain, snow, dust and even by fingers, which will change the channel's characteristics and degrades the system's performance. In order to solve this problem, we propose a cross-entropy inspired antenna array diagnosis detection (CE-AAD) technique by exploiting the correlations of adjacent antennas, when blockages occur at the transmitter. Then, we extend the proposed CE-AAD algorithm to the case, where blockages occur at transmitter and receiver simultaneously. Our simulation results show that the prop…
This paper investigates the coexistence between two key enabling technologies for the fifth generation (5G) mobile networks, non-orthogonal multiple access (NOMA) and millimeter-wave (mmWave) communications. Particularly, the application of random beamforming to the addressed mmWave-NOMA scenario is considered in this paper, in order to avoid the requirement that the base station knows all the users' channel state information. Stochastic geometry is used to characterize the performance of the proposed mmWave-NOMA transmission scheme, by using the key features of mmWave systems, e.g., mmWave tr…
In this paper, randomly-directional beamforming (RDB) is considered for millimeter-wave (mmwave) multi-user (MU) multiple-input single-output (MISO) downlink systems. By using asymptotic techniques, the performance of RDB and the MU gain in mm-wave MISO are analyzed based on the uniform random line-of-sight (UR-LoS) channel model suitable for highly directional mm-wave radio propagation channels. It is shown that there exists a transition point on the number of users relative to the number of antenna elements for non-trivial performance of the RDB scheme, and furthermore sum rate scaling arbit…
In this study, we analyze the codebook design used for analog beamforming. Analog beamforming and combining suffer from a subspace sampling limitation, that is, the receiver cannot directly observe the channel coefficients; instead, the receiver observes a noisy version of their weighted combination. To resolve this, the transmitter and the receiver usually collaborate to determine the best beamformer combiner pair during the beam-sweeping process. This is done by evaluating a limited number of codewords chosen from a pre-defined codebook. In this study, we propose a new framework inspired by …
A potential tremendous spectrum resource makes millimeter wave (mmWave) communications a promising technology. High power consumption due to a large number of antennas and analog-to-digital converters (ADCs) for beamforming to overcome the large propagation losses is problematic in practice. As a hybrid beamforming architecture and low-resolution ADCs are considered to reduce power consumption, estimation of mmWave channels becomes challenging. We evaluate several channel estimation algorithms for wideband mmWave systems with hybrid beamforming and low-resolution ADCs. Through simulation, we s…
In this paper we explore non-orthogonal multiple access (NOMA) in millimeter-wave (mmWave) communications (mmWave-NOMA). In particular, we consider a typical problem, i.e., maximization of the sum rate of a 2-user mmWave-NOMA system. In this problem, we need to find the beamforming vector to steer towards the two users simultaneously subject to an analog beamforming structure, while allocating appropriate power to them. As the problem is non-convex and may not be converted to a convex problem with simple manipulations, we propose a suboptimal solution to this problem. The basic idea is to deco…
With the explosive growth of mobile data, the demand of high-speed railway (HSR) passengers for broadband wireless access services urgently needs the support of ultra-highspeed scenario broadband wireless communication. Millimeterwave (mmWave) can achieve high data transmission rates, but it is accompanied by high propagation loss and vulnerability to blockage. To address this issue, developments of directional antennas and unmanned aerial vehicles (UAVs) enhance the robustness of the mmWave train-ground communication system. In this paper, we propose a UAV and MRs relay assistance (UMRA) algo…
This paper proposes the use of subspace tracking algorithms for performing MIMO channel estimation at millimeter wave (mmWave) frequencies. Using a subspace approach, we develop a protocol enabling the estimation of the right (resp. left) singular vectors at the transmitter (resp. receiver) side; then, we adapt the projection approximation subspace tracking with deflation (PASTd) and the orthogonal Oja (OOJA) algorithms to our framework and obtain two channel estimation algorithms. The hybrid analog/digital nature of the beamformer is also explicitly taken into account at the algorithm design …
The integration of non-orthogonal multiple access in millimeter-Wave communications (mmWave-NOMA) can significantly improve the spectrum efficiency and increase the number of users in the fifth-generation (5G) mobile communication. In this paper we consider a downlink mmWave-NOMA cellular system, where the base station is mounted with an analog beamforming phased array, and multiple users are served in the same time-frequency resource block. To guarantee user fairness, we formulate a joint beamforming and power allocation problem to maximize the minimal achievable rate among the users, i.e., w…
Airy Beamforming for Radiative Near-Field MU-XL-MIMO: Overcoming Half-Space Blockage
Peng Cheng Laboratory（鹏城实验室）；State Key Laboratory of Millimeter Waves, School of Information Science and Engineering, Southeast University（东南大学信息科学与工程学院毫米波国家重点实验室）；Department of Electrical and Computer Engineering, National University of Singapore（新加坡国立大学电气与计算机工程系）；Purple Mountain Laboratories（紫金山实验室）；School of Electrical and Computer Science, Peking University（北京大学电子学与微电子学院）
Hybrid beamforming provides a promising solution to achieve high data rate transmission at millimeter waves. Implementing hybrid beamforming at a transceiver based on available channel state information is a common solution. However, many reference methods ignore the complexity of channel estimation for large antenna arrays or subsequent steps, such as the singular value decomposition of a channel matrix. To this end, we present a low-complexity scheme that exploits implicit channel knowledge to facilitate the design of hybrid beamforming for frequency-selective fading channels. The implicit c…
In this paper, we investigate the combination of non-orthogonal multiple access and millimeter-Wave communications (mmWave-NOMA). A downlink cellular system is considered, where an analog phased array is equipped at both the base station and users. A joint Tx-Rx beamforming and power allocation problem is formulated to maximize the achievable sum rate (ASR) subject to a minimum rate constraint for each user. As the problem is non-convex, we propose a sub-optimal solution with three stages. In the first stage, the optimal power allocation with a closed form is obtained for an arbitrary fixed Tx…
The combination of millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems and index modulation (IM) technique has recently constituted a novel form of mmWave hybrid beamforming. Lots of studies have been conducted to show that such system has the potential to outperform conventional mmWave-MIMOs with respect to spectral efficiency (SE). Most of the current works only focused on designing hybrid beamforming structures to empirically achieve higher SE performance. However, a fundamental question that whether IM technique can truly improve the SE of current mmWave hybrid beamformi…
Multiple-input multiple-output (MIMO) millimeter wave (mmWave) systems are vulnerable to hardware impairments due to operating at high frequencies and employing a large number of radio- frequency (RF) hardware components. In particular, nonlinear power amplifiers (PAs) employed at the transmitter distort the signal when operated close to saturation due to energy efficiency considerations. In this paper, we study the performance of a MIMO mmWave hybrid beamforming scheme in the presence of nonlinear PAs. First, we develop a statistical model for the transmitted signal in such systems and show t…
In this paper, we investigate the combination of two key enabling technologies for the fifth generation (5G) wireless mobile communication, namely millimeter-wave (mmWave) communications and non-orthogonal multiple access (NOMA). In particular, we consider a typical 2-user uplink mmWave-NOMA system, where the base station (BS) equips an analog beamforming structure with a single RF chain and serves 2 NOMA users. An optimization problem is formulated to maximize the achievable sum rate of the 2 users while ensuring a minimal rate constraint for each user. The problem turns to be a joint power c…
To support high data rate urgent or ad hoc communications, we consider mmWave UAV cellular networks and the associated challenges and solutions. To enable fast beamforming training and tracking, we first investigate a hierarchical structure of beamforming codebooks and design of hierarchical codebooks with different beam widths via the sub-array techniques. We next examine the Doppler effect as a result of UAV movement and find that the Doppler effect may not be catastrophic when high gain directional transmission is used. We further explore the use of millimeter wave spatial division multiple…
We investigate Tx/Rx joint beamforming in millimeter-wave communications (MMWC). As the multipath components (MPCs) have different steering angles and independent fadings, beamforming aims at achieving array gain as well as diversity gain in this scenario. A sub-optimal beamforming scheme is proposed to find the antenna weight vectors (AWVs) at Tx/Rx via iterative eigenvalue decomposition (EVD), provided that full channel state information (CSI) is available at both the transmitter and receiver. To make this scheme practically feasible in MMWC, a corresponding training approach is suggested to…
In millimeter wave (mmWave) systems, it is challenging to ensure the reliable connectivity of communications due to its sensitivity to the presence of blockages. In order to improve the robustness of the mmWave system under the presence of the random blockages, multiple reconfigurable intelligent surfaces (RISs) are deployed to enhance the spatial diversity gain, and robust beamforming is then designed based on a stochastic optimization for minimizing the maximum outage probability among multiple users to ensure the fairness. Under the stochastic optimization framework, we adopt the stochastic…
Millimeter-wave (mm-wave) is a promising technique to enhance the network capacity and coverage of next-generation (5G) based on utilizing a great number of available spectrum resources in mobile communication. Improving the 5G network requires enhancing and employing mm-wave beamforming channel propagation characteristics. To achieve high data rates, system performance remains a challenge given the impact of propagation channels in mm-wave that is insufficient in both path loss, delay spread, and penetration loss. Additional challenges arise due to high cost and energy consumption, which requ…
The use of the millimeter (mm) wave spectrum for next generation (5G) mobile communication has gained significant attention recently. The small carrier wavelengths at mmwave frequencies enable synthesis of compact antenna arrays, providing beamforming gains that compensate the increased propagation losses. In this work, we investigate the feasibility of employing multiple antenna arrays to obtain diversity/multiplexing gains in mmwave systems, where each of the arrays is capable of beamforming independently. Considering a codebook based beamforming system (e.g., to facilitate limited feedback)…
Unlocking the full potential of millimeter-wave and sub-terahertz wireless communication networks hinges on realizing unprecedented low-latency and high-reliability requirements. The challenge in meeting those requirements lies partly in the sensitivity of signals in the millimeter-wave and sub-terahertz frequency ranges to blockages. One promising way to tackle that challenge is to help a wireless network develop a sense of its surrounding using machine learning. This paper attempts to do that by utilizing deep learning and computer vision. It proposes a novel solution that proactively predic…
In this paper, a new mathematical framework to the analysis of millimeter wave cellular networks is introduced. Its peculiarity lies in considering realistic path-loss and blockage models, which are derived from recently reported experimental data. The path-loss model accounts for different distributions of line-of-sight and non-line-of-sight propagation conditions and the blockage model includes an outage state that provides a better representation of the outage possibilities of millimeter wave communications. By modeling the locations of the base stations as points of a Poisson point process…
The focus of this paper is on beamforming in a millimeter-wave (mmW) multi-input multi-output (MIMO) setup that has gained increasing traction in meeting the high data-rate requirements of next-generation wireless systems. For a given MIMO channel matrix, the optimality of beamforming with the dominant right-singular vector (RSV) at the transmit end and with the matched filter to the RSV at the receive end has been well-understood. When the channel matrix can be accurately captured by a physical (geometric) scattering model across multiple clusters/paths as is the case in mmW MIMO systems, we …
To meet the demand of supreme data rates in terabits-per-second, the next-generation mobile system needs to exploit the abundant spectrum in the millimeter-wave and terahertz bands. However, high-frequency transmission heavily relies on large-scale antenna arrays to reap high beamforming gain, used to compensate for severe propagation loss. It raises a problem of omni-directional beamforming during the phase of initial access, where a base station is required to broadcast synchronization signals and system information to all users within its coverage. This paper proposes a novel initial beamfo…
As more and more people choose high-speed rail (HSR) as a means of transportation for short trips, there is ever growing demand of high quality of multimedia services. With its rich spectrum resources, millimeter wave (mm-wave) communications can satisfy the high network capacity requirements for HSR. Also, it is possible for receivers (RXs) to be equipped with antenna arrays in mm-wave communication systems due to its short wavelength. However, as HSRs run with high speed, the received signal power (RSP) varies rapidly over a cell and it is the lowest at the edge of the cell compared to other…
Hybrid beamforming (HBF) includes analog beamforming with phase shifted array in RF domain and digital beamforming in baseband domain. Phase shifted array is usually made up with a large amount of phase shifters. Limited to the manufacturing techniques, phase shifters are unavoidable to have phaseshifting error and gain error. In the paper we study the influence of imperfect phase shifters upon the performance of multiuser mmWave massive MIMO systems1 with the wireless channel modeled by Rice fading. We derive the upper bound of the achievable sum rate with imperfect phase shifters, which can …
In this work, we investigate hybrid analog-digital beamforming (HBF) architectures for uplink cell-free (CF) millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems. {We first propose two HBF schemes, namely, decentralized HBF (D-HBF) and semi-centralized HBF (SC-HBF). In the former, both the digital and analog beamformers are generated independently at each AP based on the local channel state information (CSI). In contrast, in the latter, only the digital beamformer is obtained locally at the AP, whereas the analog beamforming matrix is generated at the central processi…
