The synthesis of one-dimensional van der Waals heterostructures was realized recently, which opens up new possibilities for prospective applications in electronics and optoelectronics. The even reduced dimension will enable novel properties and further miniaturization beyond the capabilities of its two-dimensional counterparts have revealed. The natural doping results in p-type electrical characteristics for semiconducting single-walled carbon nanotubes, while n-type for molybdenum disulfide with conventional noble metal contacts. Therefore, we demonstrate here a one-dimensional heterostructure nanotube of 11-nm-wide, with the coaxial assembly of semiconducting single-walled carbon nanotube, insulating boron nitride nanotube, and semiconducting molybdenum disulfide nanotube which induces a radial semiconductor-insulator-semiconductor heterojunction. When opposite potential polarity was applied on semiconducting single-walled carbon nanotube and molybdenum disulfide nanotube, respectively, the rectifying effect was materialized.
The p-n diodes represent the most fundamental device building block for diverse optoelectronic functions, but are difficult to achieve in atomically thin transition metal dichalcogenides (TMDs) due to the inability to selectively dope them into p- or n-type semiconductors. Here we report the first demonstration of an atomically thin and atomically sharp heterojunction p-n diode by vertically stacking p-type monolayer tungsten diselenide (WSe2) and n-type few-layer molybdenum disulfide (MoS2). Electrical measurement demonstrates excellent diode characteristics with well-defined current rectific…
Metal-semiconductor interfaces, known as Schottky junctions, have long been hindered by defects and impurities. Such imperfections dominate the electrical characteristics of the junction by pinning the metal Fermi energy. We report measurements on a boron nitride encapsulated graphene-tungsten diselenide (WSe$_2$) Schottky junction which exhibits ideal diode characteristics and a complete lack of Fermi-level pinning. The Schottky barrier height of the device is rigidly tuned by electrostatic gating of the WSe$_2$, enabling experimental verification of the Schottky-Mott limit in a single device…
Due to their wide band gaps, III-N materials can exhibit behaviors ranging from the semiconductor class to the dielectric class. Through an analogy between a Metal/AlGaN/AlN/GaN diode and a MOS contact, we make use of this dual nature and show a direct path to capture the energy band diagram of the nitride system. We then apply transparency calculations to describe the forward conduction regime of a III-N heterojunction diode and demonstrate it realizes a tunnel diode, in contrast to its regular Schottky Barrier Diode designation. Thermionic emission is ruled out and instead, a coherent electr…
Semiconductor heterostructures form the cornerstone of many electronic and optoelectronic devices and are traditionally fabricated using epitaxial growth techniques. More recently, heterostructures have also been obtained by vertical stacking of two-dimensional crystals, such as graphene and related two- dimensional materials. These layered designer materials are held together by van der Waals forces and contain atomically sharp interfaces. Here, we report on a type- II van der Waals heterojunction made of molybdenum disulfide and tungsten diselenide monolayers. The junction is electrically tu…
Phosphorene, an elemental 2D material, which is the monolayer of black phosphorus, has been mechanically exfoliated recently. In its bulk form, black phosphorus shows high carrier mobility (~10000 cm2/Vs) and a ~0.3 eV direct bandgap. Well-behaved p-type field-effect transistors with mobilities of up to 1000 cm2/Vs, as well as phototransistors, have been demonstrated on few-layer black phosphorus, showing its promise for electronics and optoelectronics applications due to its high hole mobility and thickness-dependence direct bandgap. However, p-n junctions, the basic building blocks of modern…
Van der Waals heterojunctions between two-dimensional (2D) layered materials and nanomaterials of different dimensions present unique opportunities for gate-tunable optoelectronic devices. Mixed dimensional p-n heterojunction diodes, such as p-type pentacene (0D) and n-type monolayer MoS2 (2D), are especially interesting for photovoltaic applications where the absorption cross-section and charge transfer processes can be tailored by rational selection from the vast library of organic molecules and 2D materials. Here, we study the kinetics of excited carriers in pentacene-MoS2 p-n type-II heter…
A variety of fabrication methods for van der Waals heterostructures have been demonstrated; however, their wafer-scale deposition remains a challenge. Here we report few-layer van der Waals PtS2/PtSe2 heterojunction photodiodes fabricated on a 2" SiO2/Si substrate that is only limited by the size of work chamber of the growth equipment, offering throughputs necessary for practical applications. Theoretical simulation results show that the bandgap of PtS2 is shrunk to half of its original size in the PtS2/PtSe2 heterostructures, while PtSe2 exhibits a limited response to the coupling. Both PtSe…
The p-n junction diode and field-effect transistor (FET) are the two most ubiquitous building blocks of modern electronics and optoelectronics. In recent years, the emergence of reduced dimensionality materials has suggested that these components can be scaled down to atomic thicknesses. Although high performance field-effect devices have been achieved from monolayered materials and their heterostructures, a p-n heterojunction diode derived from ultrathin materials is notably absent and constrains the fabrication of complex electronic and optoelectronic circuits. Here, we demonstrate a gate-tu…
We report novel graphene nanoribbon (GNR)/semiconductor nanowire (SNW) heterojunction light-emitting diodes (LEDs) for the first time. The GNR and SNW have a face-to-face contact structure, which has the merit of bigger active region. ZnO, CdS, and CdSe NWs were employed in our case. At forward biases, the GNR/SNW heterjunction LEDs could emit light with wavelengths varying from ultraviolet (380 nm) to green (513 nm) to red (705 nm), which were determined by the band-gaps of the involved SNWs. The mechanism of light emitting for the GNR/SNW heterojunction LED was discussed. Our approach can ea…
The availability of transistors capable of operating at low supply voltage is essential to improve the key performance metric of computing circuits, i.e., the number of operations per unit energy. In this paper, we propose a new device concept for energy-efficient, steep-slope transistors based on heterojunctions of 2D materials. We show that by injecting electrons from an isolated and weakly dispersive band into a strongly dispersive one, subthermionic subthreshold swings can be obtained, as a result of a cold-source effect and of a reduced thermalization of carriers. This mechanism is implem…
The band structure of transition metal dichalcogenides (TMDCs) with valence band edges at different locations in the momentum space could be harnessed to build devices that operate relying on the valley degree of freedom. To realize such valleytronic devices, it is necessary to control and manipulate the charge density in these valleys, resulting in valley polarization. While this has been demonstrated using optical excitation, generation of valley polarization in electronic devices without optical excitation remains difficult. Here, we demonstrate spin injection from a ferromagnetic electrode…
The p-n junction constructed from the group-10 TMDCs, or namely, transition metal dichalcogenides with an intrinsic layered structure, is not considerably reported. This study presents a mechanical exfoliation-based technique to prepare PtS2 pyramids Si p-n junctions for an investigation of the tunneling and breakdown diodes. the demonstrated p-n diode exhibited a high rectifying performance reaching a rectification ration (If/Ir) to 7.2 *10^4 at zero gate bias with an ideality factor of 1.5. The zener tunneling was observed at a low reverse bias region of breakdown voltage (from -6 to -1V) at…
In-Plane Anisotropy-Driven Directional Charge Transport in van der Waals p-n Heterojunction
Indian Association for the Cultivation of Science（印度科学文化促进协会）；Sincrotrone Trieste s.c.p.a.（的里雅斯特同步辐射中心）；Indian Institute of Technology Tirupati（蒂鲁帕提印度理工学院）；UGC-DAE Consortium for Scientific Research（UGC-DAE科学研究联盟）
By the insertion of thin InGaN layers into Nitrogen-polar GaN p-n junctions, polarization-induced Zener tunnel junctions are studied. The reverse-bias interband Zener tunneling current is found to be weakly temperature dependent, as opposed to the strongly temperature-dependent forward bias current. This indicates tunneling as the primary reverse-bias current transport mechanism. The Indium composition in the InGaN layer is systematically varied to demonstrate the increase in the interband tunneling current. Comparing the experimentally measured tunneling currents to a model helps identify the…
A general self-aligned fabrication scheme is reported here for a diverse class of electronic devices based on van der Waals materials and heterojunctions. In particular, self-alignment enables the fabrication of source-gated transistors in monolayer MoS2 with near-ideal current saturation characteristics and channel lengths down to 135 nm. Furthermore, self-alignment of van der Waals p-n heterojunction diodes achieves complete electrostatic control of both the p-type and n-type constituent semiconductors in a dual-gated geometry, resulting in gate-tunable mean and variance of anti-ambipolar Ga…
We reveal stacking-induced strong coupling between atomic motion and interlayer excitons through photocurrent measurements of WSe$_2$/MoSe$_2$ heterojunction photodiodes. Strong coupling manifests as pronounced periodic sidebands in the photocurrent spectrum in frequency windows close to the interlayer exciton resonances. The sidebands, which repeat over large swathes of the interlayer exciton photocurrent spectrum, occur in energy increments corresponding directly to a prominent vibrational mode of the heterojunction. Such periodic patterns, together with interlayer photoconductance oscillati…
Van der Waals (vdW) heterojunctions composed of 2-dimensional (2D) layered materials are emerging as a solid-state materials family that exhibit novel physics phenomena that can power high performance electronic and photonic applications. Here, we present the first demonstration of an important building block in vdW solids: room temperature (RT) Esaki tunnel diodes. The Esaki diodes were realized in vdW heterostructures made of black phosphorus (BP) and tin diselenide (SnSe2), two layered semiconductors that possess a broken-gap energy band offset. The presence of a thin insulating barrier bet…
In the past decade graphene has been one of the most studied material for several unique and excellent properties. Due to its two dimensional nature, physical and chemical properties and ease of manipulation, graphene offers the possibility of integration with the exiting semiconductor technology for next-generation electronic and sensing devices. In this context, the understanding of the graphene/semiconductor interface is of great importance since it can constitute a versatile standalone device as well as the building-block of more advanced electronic systems. Since graphene was brought to t…
Heterojunctions between three-dimensional (3D) semiconductors with different bandgaps are the basis of modern light-emitting diodes, diode lasers, and high-speed transistors. Creating analogous heterojunctions between different two-dimensional (2D) semiconductors would enable band engineering within the 2D plane and open up new realms in materials science, device physics and engineering. Here we demonstrate that seamless high-quality in-plane heterojunctions can be grown between the 2D monolayer semiconductors MoSe2 and WSe2. The junctions, grown by lateral hetero-epitaxy using physical vapor …
The electrical and photodiode characteristics of ensemble and single p-GaN nanowire and n-Si heterojunction devices were studied. Ideality factor of the single nanowire p-GaN/n-Si device was found to be about three times lower compared to that of the ensemble nanowire device. Apart from the deep-level traps in p-GaN nanowires, defect states due to inhomogeneity in Mg dopants in the ensemble nanowire device are attributed to the origin of high ideality factor. Photovoltaic mode of ensemble nanowire device showed an improvement in the fill-factors up to 60 percent over the single nanowire device…
Charge transfer plays a key role at the interfaces of heterostructures, which can affect electronic structures and ultimately the physical properties of the materials. However, charge transfer is difficult to manipulate externally once the interface formed. Here, we report electrically tunable charge transfer in Fe3GeTe2/Cr2Ge2Te6/Fe3GeTe2 all-magnetic van der Waals heterostructures, which can be exploited to selectively modify the magnetic properties of the top or bottom Fe3GeTe2 electrodes. The directional charge transfer from metallic Fe3GeTe2 to semiconducting Cr2Ge2Te6 remarkably modifies…
van der Waals (vdW) heterojunctions formed by two-dimensional (2D) materials have attracted tremendous attention due to their excellent electrical/optical properties and device applications. However, current 2D heterojunctions are largely limited to atomic crystals, and hybrid organic/inorganic structures are rarely explored. Here, we fabricate hybrid 2D heterostructures with p-type dioctylbenzothienobenzothiophene (C8-BTBT) and n-type MoS2. We find that few-layer C8-BTBT molecular crystals can be grown on monolayer MoS2 by vdW epitaxy, with pristine interface and controllable thickness down t…
Van der Waals (vdW) semiconductors are attractive for highly scaled devices and heterogeneous integration since they can be isolated into self-passivated, two-dimensional (2D) layers that enable superior electrostatic control. These attributes have led to numerous demonstrations of field-effect devices ranging from transistors to triodes. By exploiting the controlled, substitutional doping schemes in covalently-bonded, three-dimensional (3D) semiconductors and the passivated surfaces of 2D semiconductors, one can construct devices that can exceed performance metrics of 'all-2D' vdW heterojunct…
The recent emergence of a wide variety of two-dimensional (2D) materials has created new opportunities for device concepts and applications. In particular, the availability of semiconducting transition metal dichalcogenides, in addition to semi-metallic graphene and insulating boron nitride, has enabled the fabrication of all 2D van der Waals heterostructure devices. Furthermore, the concept of van der Waals heterostructures has the potential to be significantly broadened beyond layered solids. For example, molecular and polymeric organic solids, whose surface atoms possess saturated bonds, ar…
Heterostructures of two-dimensional (2D) and three-dimensional (3D) materials form efficient devices for utilizing the properties of both classes of materials. Graphene/silicon (G/Si) Schottky diodes have been studied extensively with respect to their optoelectronic properties. Here, we introduce a method to analyze measured capacitance-voltage data of G/Si Schottky diodes connected in parallel with G/silicon dioxide/Si (GIS) capacitors. We also demonstrate the accurate extraction of the built-in potential ($Φ$$_{bi}$) and the Schottky barrier height from the measurement data independent of th…
We present, here, advanced DFT-NEGF techniques that we have implemented in our ATOmistic MOdelling Solver, ATOMOS, to explore transport in novel materials and devices and in particular in van-der-Waals heterojunction transistors. We describe our methodologies using plane-wave DFT, followed by a Wannierization step, and linear combination of atomic orbital DFT, that leads to an orthogonal and non-orthogonal NEGF model, respectively. We then describe in detail our non-orthogonal NEGF implementation including the Sancho-Rubio and electron-phonon scattering within a non-orthogonal framework. We al…
Spin-valve effect has been the focus of spintronics over the last decades due to its potential in many spintronic devices. Two-dimensional (2D) van der Waals (vdW) materials are highly expected to build the spin-valve heterojunction. However, the Curie temperatures (TC) of the vdW ferromagnetic 2D crystals are mostly below room temperature (~30-220 K). It is very challenging to develop room temperature, ferromagnetic (FM) 2D crystals based spin-valve devices which are still not available to date. We report the first room temperature, FM 2D crystal based all-2D vdW Fe3GaTe2/MoS2/Fe3GaTe2 spin v…
Interfacial charge separation and recombination at heterojunctions of monolayer transition metal dichalcogenides (TMDCs) are of interest to two dimensional optoelectronic technologies. These processes can involve large changes in parallel momentum vector due to the confinement of electrons and holes to the K-valleys in each layer. Since these high-momentum valleys are usually not aligned across the interface of two TMDC monolayers, how parallel momentum is conserved in the charge separation or recombination process becomes a key question. Here we probe this question using the model system of a…
The intrinsic spin-dependent transport properties of two types of lateral VS2|MoS2 heterojunctions are systematically investigated using first-principles calculations, and their various nanodevices with novel properties are designed. The lateral VS2|MoS2 heterojunction diodes show a perfect rectifying effect and are promising for the applications of Schottky diodes. A large spin-polarization ratio is observed for the A-type device and pure spin-mediated current is then realized. The gate voltage significantly tunes the current and rectification ratio of their field-effect transistors (FETs). I…
The advent of graphene and related 2D materials has recently led to a new technology: heterostructures based on these atomically thin crystals. The paradigm proved itself extremely versatile and led to rapid demonstration of tunnelling diodes with negative differential resistance, tunnelling transistors5, photovoltaic devices, etc. Here we take the complexity and functionality of such van der Waals heterostructures to the next level by introducing quantum wells (QWs) engineered with one atomic plane precision. We describe light emitting diodes (LEDs) made by stacking up metallic graphene, insu…
Recently demonstrated metal-semiconductor heterojunctions with few-atom thickness show their promise as 2D Schottky contacts for future integrated circuits and nanoelectronics. The theory for 3D Schottky contacts, however, fails on these low-dimensional systems. Here, we propose a new model that yields carrier distribution and potential profile across the 2D metal-semiconductor heterojunction under the equilibrium condition, based on the input from first-principle calculations. Our calculation also suggests that, at the same forward bias, the current density of a stack of 2D graphene-phosphore…
Moiré patterns are common in Van der Waals heterostructures and can be used to apply periodic potentials to elementary excitations. We show that the optical absorption spectrum of transition metal dichalcogenide bilayers is profoundly altered by long period moiré patterns that introduce twist-angle dependent satellite excitonic peaks. Topological exciton bands with non-zero Chern numbers that support chiral excitonic edge states can be engineered by combining three ingredients: i) the valley Berry phase induced by electron-hole exchange interactions, ii) the moiré potential, and iii) the valle…
The integration of two-dimensional materials such as transition metal dichalcogenides with bulk semiconductors offer interesting opportunities for 2D/3D heterojunction-based novel device structures without any constraints of lattice matching. By exploiting the favorable band alignment at the GaN/MoS2 heterojunction, an Esaki interband tunnel diode is demonstrated by transferring large area, Nb-doped, p-type MoS2 onto heavily n-doped GaN. A peak current density of 446 A/cm2 with repeatable room temperature negative differential resistance, peak to valley current ratio of 1.2, and minimal hyster…
Generators of random sequences used in high-end applications such as cryptography rely on entropy sources for their indeterminism. Physical processes governed by the laws of quantum mechanics are excellent sources of entropy available in nature. However, extracting enough entropy from such systems for generating truly random sequences is challenging while maintaining the feasibility of the extraction procedure for real-world applications. Here, we present a compact and an all-electronic van der Waals (vdW) heterostructure-based device capable of detecting discrete charge fluctuations for extra…
The emergence of semiconducting materials with inert or dangling bond-free surfaces has created opportunities to form van der Waals heterostructures without the constraints of traditional epitaxial growth. For example, layered two-dimensional (2D) semiconductors have been incorporated into heterostructure devices with gate-tunable electronic and optical functionalities. However, 2D materials present processing challenges that have prevented these heterostructures from being produced with sufficient scalability and/or homogeneity to enable their incorporation into large-area integrated circuits…
Recent progress in preparing well controlled 2D van der Waals heterojunctions has opened up a new frontier in materials physics. In this paper we address the intriguing energy gaps that are sometimes observed when a graphene sheet is placed on a hexagonal boron nitride substrate, demonstrating that they are produced by an interesting interplay between structural and electronic properties, including electronic many-body exchange interactions. Our theory is able to explain the observed gap behavior by accounting first for the structural relaxation of graphene's carbon atoms when placed on a boro…
Two-dimensional (2D) materials are a new type of materials under intense study because of their interesting physical properties and wide range of potential applications from nanoelectronics to sensing and photonics. Monolayers of semiconducting transition metal dichalcogenides MoS2 or WSe2 have been proposed as promising channel materials for field-effect transistors (FETs). Their high mechanical flexibility, stability and quality coupled with potentially inexpensive production methods offer potential advantages compared to organic and crystalline bulk semiconductors. Due to quantum mechanical…
We investigate van der Waals (vdW) heterostructures made of germanene, stanene or silicene with hexagonal Boron Nitride (h-BN). The intriguing topological properties of these buckled honeycomb materials can be maintained and further engineered in the heterostructures, where the competition between the substrate effect and external electric fields can be used to control the tunable topological phase transitions. Using such heterostructures as building blocks, various vdW topological domain walls (DW) are designed, along which there exist valley polarized quantum spin Hall edge states or valley-…
Non-reciprocal electronic transport in a spatially homogeneous system arises from the simultaneous breaking of inversion and time-reversal symmetries. Superconducting and Josephson diodes, a key ingredient for future non-dissipative quantum devices, have recently been realized. Only a few examples of a vertical superconducting diode effect have been reported and its mechanism, especially whether intrinsic or extrinsic, remains elusive. Here we demonstrate a substantial supercurrent non-reciprocity in a van der Waals vertical Josephson junction formed with a Td-WTe2 barrier and NbSe2 electrodes…
Two-dimensional semiconductors are excellent candidates for next-generation electronics and optoelec-tronics thanks to their electrical properties and strong light-matter interaction. To fabricate devices with optimal electrical properties, it is crucial to have both high-quality semiconducting crystals and ideal con-tacts at metal-semiconductor interfaces. Thanks to the mechanical exfoliation of van der Waals crystals, atomically-thin high-quality single-crystals can easily be obtained in a laboratory. However, conventional metal deposition techniques can introduce chemical disorder and metal…
Van der Waals (vdW) tunnel junctions are attractive due to their atomically sharp interface, gate tunablity, and robustness against lattice mismatch between the successive layers. However, the negative differential resistance (NDR) demonstrated in this class of tunnel diodes often exhibits noisy behaviour with low peak current density, and lacks robustness and repeatability, limiting their practical circuit applications. Here we propose a strategy of using a 1L-WS$_2$ as an optimum tunnel barrier sandwiched in a broken gap tunnel junction of highly doped black phosphorus (BP) and SnSe$_2$. We …
Ferromagnetic van der Waals (vdW) materials are in demand for spintronic devices with all-two-dimensional-materials heterostructures. Here, we demonstrate mechanical exfoliation of magnetic-atom-intercalated transition metal dichalcogenide Cr1/3TaS2 from its bulk crystal; previously such intercalated materials were thought difficult to exfoliate. Magnetotransport in exfoliated tens-of-nanometres-thick flakes revealed ferromagnetic ordering below its Curie temperature TC ~ 110 K as well as strong in-plane magnetic anisotropy; these are identical to its bulk properties. Further, van der Waals he…
The physics of two-dimensional (2D) materials and heterostructures based on such crystals has been developing extremely fast. With new 2D materials, truly 2D physics has started to appear (e.g. absence of long-range order, 2D excitons, commensurate-incommensurate transition, etc). Novel heterostructure devices are also starting to appear - tunneling transistors, resonant tunneling diodes, light emitting diodes, etc. Composed from individual 2D crystals, such devices utilize the properties of those crystals to create functionalities that are not accessible to us in other heterostructures. We re…
The integration of different two-dimensional materials within a multilayer van der Waals (vdW) heterostructure offers a promising technology for realizing high performance opto-electronic devices such as photodetectors and light sources1-3. Transition metal dichalcogenides, e.g. MoS2 and WSe2, have been employed as the optically-active layer in recently developed heterojunctions. However, MoS2 and WSe2 become direct band gap semiconductors only in mono- or bilayer form4,5. In contrast, the metal monochalcogenides InSe and GaSe retain a direct bandgap over a wide range of layer thicknesses from…
We report experimental measurements for ultrathin (< 15 nm) van der Waals heterostructures exhibiting external quantum efficiencies exceeding 50%, and show that these structures can achieve experimental absorbance > 90%. By coupling electromagnetic simulations and experimental measurements, we show that pn WSe2/MoS2 heterojunctions with vertical carrier collection can have internal photocarrier collection efficiencies exceeding 70%.
Two-dimensional (2D) semiconductors have shown great promise in (opto)electronic applications. However, their developments are limited by a large Schottky barrier (SB) at the metal-semiconductor junction (MSJ), which is difficult to tune by using conventional metals due to the strong Fermi level pinning (FLP) effect. Here we show that, this problem can be overcome by using 2D metals, which are bounded with 2D semiconductors through van der Waals (vdW) interaction. This success relies on a weak FLP at the vdW MSJ, which is attributed to the suppression of metal-induced gap states. Consequently,…
Excitons dominate the optics of atomically-thin transition metal dichalcogenides and 2D van der Waals heterostructures. Interlayer 2D excitons, with an electron and a hole residing in different layers, form rapidly in heterostructures either via direct charge transfer or via Coulomb interactions that exchange energy between layers. Here, we report prominent intertube excitonic effects in quasi-1D van der Waals heterostructures consisting of C/BN/MoS$_2$ core/shell/skin nanotubes. Remarkably, under pulsed infrared excitation of excitons in the semiconducting CNTs we observed a rapid (sub-picose…
Van der Waals heterostructures formed by stacking different atomically thin layered materials have emerged as the sought-after device platform for electronic and optoelectronic applications. Determining the spatial extent of all the encapsulated components in such vertical stacks is key to optimal fabrication methods and improved device performance. Here we employ electrostatic force microscopy as a fast and non-invasive microscopic probe that provides compelling images of two dimensional layers buried over 30 nm below the sample surface. We demonstrate the versatility of the technique by stud…
We investigated the electronic and optoelectronic properties of vertical van der Waals heterostructure photodetectors using layered p type GaSe and n type InSe, with graphene as the transparent electrodes. Not only the photocurrent peaks from the layered GaSe and InSe themselves were observed, also the interlayer optical transition peak was observed, which is consistent with the first-principles calculation. The built-in electric field between p-n heterojunction and the advantage of the graphene electrodes can effectively separate the photo-induced electron-hole pairs, and thus lead to the res…
We investigate a two-dimensional (2D) heterostructure consisting of few-layer direct bandgap ReS2, a thin h-BN layer and a monolayer graphene for application to various electronic devices. Metal-insulator-semiconductor (MIS)-type devices with two-dimensional (2D) van-der-Waals (vdW) heterostructures have recently been studied as important components to realize various multifunctional device applications in analogue and digital electronics. The tunnel diodes of ReS2/h-BN/graphene exhibit light tuneable rectifying behaviours with low ideality factors and nearly temperature independent electrical…
