In this work, the effect of building direction on the microstructure evolution of laser-powder bed fusion (LPBF) processed AlSi10Mg alloy was investigated. The building direction, as shown in experimentally fabricated parts, can influence the solidification behavior and promote morphological transitions in cellular dendritic microstructures. We develop a thermal model to systemically address the impact of laser processing conditions, and building direction on the thermal characteristics of the molten pool during laser processing of AlSi10Mg alloy. We then employ a multi-order parameter phase field model to study the microstructure evolution of LPBF-AlSi10Mg in the dilute limit, using the underlying thermal conditions for horizontal and vertical building directions as input. The phase field model employed here is designed to simulate solidification using heterogeneous nucleation from inoculant particles allowing to take into account morphological phenomena including the columnar-to-equiaxed transition (CET). The phase field model is first validated against the predictions of the previously developed steady-state CET theory of Hunt \cite{hunt1984steady}. It is then used under transient conditions to study microstructure evolution, revealing that the nucleation rate is noticeably higher in the horizontally built samples due to larger constitutional undercooling, which is consistent with experimental observations. We further quantify the effect of building direction on the local cooling conditions, and consequently on the grain morphology.
Laser-based additive manufacturing offers a promising route for 3D printing of metallic parts. We evidence experimentally a particular columnar solidification microstructure in a Laser Powder-Bed Fusion processed Inconel 718 nickel-based alloy, that we interpret using phase-field simulations and classical dendritic growth theories. Owing to the large temperature gradient and cooling rate, solidification takes places through dendritic arrays wherein the characteristic length scales, i.e tip radius, diffusion length and primary spacing, are of the same order. This leads to a weak mutual interact…
A path to lowering the economic barrier associated with the high cost of metal additively manufactured components is to reduce the waste via powder reuse (powder cycled back into the process) and recycling (powder chemically, physically, or thermally processed to recover the original properties) strategies. In electron beam powder bed fusion, there is a possibility of reusing 95 - 98% of the powder that is not melted. However, there is a lack of systematic studies focusing on quantifying the variation of powder properties induced by number of reuse cycles. This work compares the influence of m…
Commercial powder bed fusion additive manufacturing systems use recoaters for the layer-by-layer distribution of powder. Despite the known limitations of recoaters, there has been relatively little work presented on the possible benefits of alternative powder delivery systems. Here, we show the use of a technology using simple vibration to control the powder flow for powder bed additive manufacturing. The capabilities of this approach are illustrated experimentally using two very different powders; a `conventional' gas atomized Ti-6Al-4V powder designed for electron beam additive manufacturing…
One of the major barriers in adapting the existing EB-PBF process parameters to a new powder material system is controlling the preheating conditions such that every layer of powder results in enough partial sintering to create a coherent powder cake. To be able to understand the powder sintering process and adapt it to other materials, we must look at the degree of sintering and the effective thermal conductivity of the powder bed. An in-depth understanding of these characteristics will help tailor the preheating conditions and furthermore, make it easier to remove/de-powder intricate parts a…
In this study, a post-heat treatment design for additively manufactured copper-bearing high-strength low-alloy (HSLA)-100 steel is performed by understanding the process-structure-property relationships. Hot isostatic pressing (HIP) is designed to reduce the porosity from 3% to less than 1% for the HSLA-100 steel processed by laser powder bed fusion (LPBF). Quenching dilatometry is employed to design the HIP parameters with the optimized cooling rate for the maximum amount of martensite transformed after HIP. Afterward, a post-heat treatment step with cyclic re-austenitization is introduced fo…
Additive manufacturing by laser powder bed fusion (LPBF) offers material versatility, capability for complex geometries, and control of mechanical properties and microstructure. However, achieving high-quality output requires process parameters that consider both local and global thermal gradients. Here, we propose a new scan pattern for mitigating part quality issues caused by non-uniform heating and cooling. A nature-inspired design method is employed to derive a spiral pattern stemming from the predator-prey behavior, and a power optimization routine is applied to maintain constant melt poo…
A multiscale numerical model based on nonequilibrium thermal effect for melting of metal powder bed subjected to constant heat flux is developed. The volume shrinkage due to density change is taken into account. The nonequilibrium model is discretized by an implicit finite difference method and solved numerically using an iterative tri-diagonal matrix algorithm. The evolutions of powder bed surface temperature and various interfacial locations as well as the melting temperature range during the melting process are investigated. The results show that liquid region, upper and lower parts of mush…
We report the synthesis of a bulk nanostructured alloy using the laser-powder bed fusion process. The equiatomic AlCoCrFeMnNi chemically complex alloy forms a nanoscale modulated structure, which is homogeneously distributed in the as-built condition. The nanostructure consisted of Al & Ni-rich ordered (B2) and Cr & Fe-rich disordered (A2) BCC phases. The two phases form an interconnected phase-network with coherent interface boundaries. Atom-probe-tomography and aberration-corrected scanning transmission electron microscopy analysis of the spatial distribution of the modulated structure sugge…
Element-Specific Solute Trapping and Grain Structure Evolution during Laser Powder Bed Fusion of Multicomponent Alloys
University of Michigan, Dearborn（密歇根大学迪尔伯恩分校）；Texas A&M University（德克萨斯农工大学）；AlphaSTAR Technology Solutions（AlphaSTAR技术解决方案）；University of Michigan, Ann Arbor（密歇根大学安娜堡分校）
Additive manufacturing (AM) of titanium (Ti) and Ti-6Al-4V lattices has been proposed for bone implants and augmentation devices. Ti and Ti-6Al-4V have favourable biocompatibility, corrosion resistance and fatigue strength for bone applications; yet, the optimal parameters for Ti-6Al-4V lattice designs corresponding to the natural micro- and meso-scale architecture of human trabecular and cortical bone are not well understood. A comprehensive review was completed to compare the natural lattice architecture properties in human bone to Ti and Ti-6Al-4V lattice structures for bone replacement and…
Polymer-bonded magnets produced by laser powder bed fusion: Influence of powder morphology, filler fraction and energy input on the magnetic and mechanical properties
Understanding alloy phase transformations during continuous cooling is important for post-processing design and optimization. In this work, continuous-cooling-transformation (CCT) diagrams of Inconel 718 alloys manufactured by laser powder bed fusion (LPBF) and suction casting are developed under different homogenization conditions. Unlike the available CCT diagrams in the reported studies, no gamma double prime and gamma prime precipitates can be observed. NbC and delta are determined to be the precipitates after cooling from the gamma matrix. Importantly, homogenization time and manufacturin…
Lattice structures composed of periodic solid frames and pores can be utilized in energy absorption applications due to their high specific strength and large deformation. However, these structures typically suffer from post-yield softenings originating from the limited plasticity of available material choices. This study aims to resolve such an issue by fabricating lattice structures made of ductile pure copper (Cu). For the first time, Cu lattice structures are fabricated through laser-powder bed fusion (L-PBF) with green laser (λ = 515 nm). Structural and microstructural analysis confirm th…
The CrMnFeCoNi high-entropy alloy is highly printable and holds great potential for structural applications. However, no significant discussions on cyclic plasticity and fatigue damage in previous studies. This study provides significant insights into the link between print processes, solidification microstructure, cyclic plasticity and fatigue damage evolution in the alloy fabricated by laser powder bed fusion. Thermodynamics-based predictions (validated by scanning transmission electron microscopy (STEM) energy dispersive X-ray spectroscopy (EDX)) showed that Cr, Co and Fe partition to the c…
We present a computational framework for the simulations of powder-bed fusion of metallic alloys, which combines: (1) CalPhaD calculations of temperature-dependent alloy properties and phase diagrams, (2) macroscale finite element (FE) thermal simulations of the material addition and fusion, and (3) microscopic phase-field (PF) simulations of solidification in the melt pool. The methodology is applied to simulate the selective laser melting (SLM) of an Inconel 718 alloy using realistic processing parameters. We discuss the effect of temperature-dependent properties and the importance of accoun…
Dislocation structures, chemical segregation, {γ^{\prime}, {γ^{\prime \prime}}, δ precipitates and Laves phase were quantified within the microstructures of Inconel 718 (IN718) produced by laser powder bed fusion additive manufacturing (AM) and subjected to standard, direct aging, and modified multi-step heat treatments. Additionally, heat-treated samples still attached to the build plates vs. those removed were also documented for a standard heat treatment. The effects of the different resulting microstructures on room temperature strengths and elongations to failure is revealed. Knowledge de…
High-throughput experiments that use combinatorial samples with rapid measurements can be used to provide process-structure-property information at reduced time, cost, and effort. Developing these tools and methods is essential in additive manufacturing where new process-structure-property information is required on a frequent basis as advances are made in feedstock materials, additive machines, and post-processing. Here we demonstrate the design and use of combinatorial samples produced on a commercial laser powder bed fusion system to study 60 distinct process conditions of nickel superalloy…
For the first time, cyclic re-austenitization is carried out for additively manufactured high-strength low-alloy (HSLA) steels in order to refine the microstructure by reducing the prior austenite grain (PAG) size. In this work, HSLA-100 steels processed using laser powder bed fusion (LPBF) technique are subjected to several cycles of re-austenitization using quenching dilatometry. Microstructure characterization for every cycle revealed the presence of bainite, martensite and martensite/austenite (M/A) islands. From the analysis of the dilatometry curves and extensive microstructure character…
Limited process control can cause metallurgical defect formation and inhomogeneous relative density in laser powder bed fusion manufactured parts. In this study, cylindrical 15-5 PH stainless steel specimens are investigated by computer tomography; it shows an edge enhanced relative density profile. Additionally, the on axis monitoring signal, obtained from recording the thermal radiation of the melt pool, is considered. Analyzing data for the full duration of the building process results in a statistically increased melt pool signature close to the edge corresponding to the density profile. E…
Effective post-heat treatment is critical to achieve desired microstructure for high-performance in additively manufactured (AM) components. In this work, the influence of homogenization on microstructure-property relationship in 17-4PH steels has been investigated. Precipitation of NbC, oxides, and ε-Cu were observed in the as-built 17-4PH steels. To design an optimum post-heat treatment, homogenization was performed at 1050oC for different times followed by aging at 482oC for 1 hour. It was identified that homogenization for 1 hour followed by aging leads to the best combination of strength …
In our study, molecular dynamics (MD) simulations of laser powder bed fusion (LPBF) have been conducted on equimolar FeNiCr medium entropy alloy (MEA) powders. With the development of newer LPBF technologies capable of printing at the microscale, an even deeper understanding of the underlying atomistic effects of the process parameters on the microstructural and mechanical properties of the manufactured FeNiCr MEA products is required. In accordance with previous literature, the parameters of the LPBF process have been systematically varied, including layer resolution from 1 to 6, laser power …
Cellular or dendritic microstructures that result as a function of additive manufacturing solidification conditions in a Ni-based melt pool are simulated in the present work using three-dimensional phase-field simulations. A macroscopic thermal model is used to obtain the temperature gradient $G$ and the solidification velocity $V$ which are provided as inputs to the phase-field model. We extract the cell spacings, cell core compositions, and cell tip as well as mushy zone temperatures from the simulated microstructures as a function of $V$. Cell spacings are compared with different scaling la…
University of Notre Dame（圣母大学）；Johnson & Johnson（强生）；Rolls-Royce Corporation（罗尔斯·罗伊斯公司）
In this study, the effects of surface roughness and pore characteristics on fatigue lives of laser powder bed fusion (LPBF) Ti-6Al-4V parts were investigated. The 197 fatigue bars were printed using the same laser power but with varied scanning speeds. These actions led to variations in the geometries of microscale pores, and such variations were characterized using micro-computed tomography. To generate differences in surface roughness in fatigue bars, half of the samples were grit-blasted and the other half machined. Fatigue behaviors were analyzed with respect to surface roughness and stati…
Additive manufacturing (AM) of metallic components promises many advantages over conventional manufacturing processes through high design flexibility across multiple length scales and precision coupled with an astonishing combination of mechanical properties. Characterizing the relationship between microstructure and mechanical properties remains one of the major challenges for this novel technology. A natural precursor is identifying the influence of the processing path on the developing microstructure. We combine experimental studies of single-track laser powder bed fusion (LPBF) scans of AI…
This study analyses literature data to identify optimised print parameters and assesses the consolidation, microstructure, and mechanical properties of Hastelloy-X printed by laser powder bed fusion. Effects of post annealing and hot-isostatic pressing (HIP) on the microstructure and mechanical properties are also revealed. The susceptibility to the solidification cracking and the as-built microstructure such as precipitation and chemical segregation were predicted by the calculation of thermodynamics phase diagrams. The distribution of solidification cracks throughout the builds was quantifie…
The concept of alloying multiple principal elements at high concentrations has led to the development of High Entropy Alloys (HEAs) with exceptional mechanical properties, making them the focus of major recent scientific endeavors. Geometrically complex HEAs with tailored microstructural characteristics can be produced using additive manufacturing technologies such as powder bed fusion (PBF). However, an in-depth study on the effect of process thermal conditions during PBF is required to effectively fabricate HEAs with desirable mechanical characteristics. Thus, in our present molecular dynami…
Open-porous scaffolds of WE43 Mg alloy with a body-center cubic cell pattern were manufactured by laser powder bed fusion with different strut diameters. The geometry of the unit cells was adequately reproduced during additive manufacturing and the porosity within the struts was minimized. The microstructure of the scaffolds was modified by means of thermal solution and ageing heat treatments and was analysed in detail by means of X-ray microtomography, optical, scanning and transmission electron microscopy. Moreover, the corrosion rates and the mechanical properties of the scaffolds were meas…
LPBF of Al alloys is associated with numerous challenges when compared to other commonly used alloys due to their higher reflectivity and thermal conductivity. In this work, processing diagrams, temperature prediction models, XCT, and metallography are used for establishing criteria in process parameter optimization of high reflectivity Al alloys based on AlSi$_{10}$Mg response in using 57 different process parameter combinations - 21 using a focused Gaussian laser beam and 36 using divergent beams. For LPBF systems with focused beam diameters <100 μm, divergent beams obtained by defocusing to…
Additive manufacturing (AM) processes produce parts with improved physical, chemical, and mechanical properties compared to conventional manufacturing processes. In AM processes, intricate part geometries are produced from multicomponent alloy powder, in a layer-by-layer fashion with multipass laser melting, solidification, and solid-state phase transformations, in a shorter manufacturing time, with minimal surface finishing, and at a reasonable cost. However, there is an increasing need for post-processing of the manufactured parts via, for example, stress relieving heat treatment and hot iso…
A three-dimensional model of a partially melted powder bed with particles stochastically distributed in size and space coordinates has been developed. Numerical simulation of temperature distributions in stainless steel AISI 316L and Al-12Si powders in vacuum, air and argon has been performed to analyze unsteady heat transfer in a porous medium. The numerical model demonstrates a large effect of heat transfer through the gas phase in case of powders with low thermal conductivities like stainless steels. At the porosity level of 65\% and above, the mechanism of heat transfer drastically changes…
We study the evolution of prior columnar $β$ phase, interface $L$ phase, and $α$ phase during directional solidification of a Ti-6Al-4V melt pool. Finite element simulations estimate the solidification temperature and velocity fields in the melt pool and analyze the stress field and thermal distortions in the solidified part during the laser powder bed fusion process. A phase-field model uses the temperature and velocity fields to predict the formation of columnar prior-$β$(Ti) phase. During the solidification of $β$ phase from an undercooled liquid, the residual liquid below the solidus tempe…
Plastic inhomogeneity, particularly localised strain, is one of the main mechanisms responsible for failures in engineering alloys. This work studied the spatial arrangement and distribution of microstructure and their influence in the plastic inhomogeneity of Inconel 718 fabricated by additive manufacturing (AM). In particular, the density and spatial distribution of geometrically necessary dislocations (GNDs) and the crystallographic texture components were examined in relation to the spatial plastic deformation. In-situ tensile testing coupled with microscopy and EBSD was performed to under…
This work provides unambiguous evidence for the occurrence of icosahedral quasicrystal (iQC) enhanced nucleation during selective laser melting of gas atomized commercially-pure Ni powders. This solidification mechanism, which has only been recently reported in a few alloys and has to date never been observed in pure metals, consists on the solidification of grains of the primary phase on the facets of iQCs formed due to the presence of icosahedral short range order in the liquid. The occurrence of iQC enhanced nucleation has been inferred from the observation in the SLM processed pure Ni samp…
During the laser powder bed fusion (L-PBF) process, the built part undergoes multiple rapid heating-cooling cycles, leading to complex microstructures with nonuniform properties. In the present work, a computational framework, which weakly couples a finite element thermal model to a non-equilibrium PF model was developed to investigate the rapid solidification microstructure of a Ni-Nb alloy during L-PBF. The framework is utilized to predict the spatial variation of the morphology and size of cellular segregation structure as well as the microsegregation in single-track melt pool microstructur…
Designing Homogeneous Ti-Nb-Fe-Sn $β$ Titanium Alloys by PBF-LB: A Pre-Alloyed Powder Blend Strategy
Universidade Estadual de Campinas (UNICAMP)（坎皮纳斯州立大学）；Charles University（查理大学）；Federal Institute of Education, Science and Technology of São Paulo (IFSP)（圣保罗联邦教育、科学和技术学院）；Institute of Thermomechanics, Czech Academy of Sciences（捷克科学院热力学研究所）
A broad range of computational models have been proposed to predict microstructure development during solidification processing but they have seldom been compared to each other on a quantitative and systematic basis. In this paper, we compare phase-field (PF) and cellular automaton (CA) simulations of polycrystalline growth in a two-dimensional melt pool under conditions relevant to additive manufacturing (powder-bed fusion). We compare the resulting grain structures using local (point-by-point) measurements, as well as averaged grain orientation distributions over several simulations. We expl…
Predicting the microstructure during selective laser sintering (SLS) is of great interests, which can compliment the current time and cost expensive trial-and-error principle with an efficient computational design tool. However, it still remains a great challenge to simulate the microstructure evolution during SLS due to the complex underlying physical phenomena. In this work, we present a three-dimensional finite element phase-field simulation of the SLS single scan, and revealed the process-microstructure relation. We use a thermodynamically consistent non-isothermal phase-field model includ…
The majority of these machines fabricate from raw material in powder form using a directed energy beam to create a local melt zone. Total hip replacement is recommended for people who have medical issues related to excessive wear of the acetabular, osteoarthritis, accident or age. Researches have shown that large numbers of hip arthroplasties (where the articular surface of a musculoskeletal joint is replaced), hip remodelling, or realignment are carried out annually and will increase in the next few decades. Manufacturing of acetabular shells by using AM is a promising and emerging method tha…
Numerical simulations are used in this work to investigate aspects of microstructure and microsegregation during rapid solidification of a Ni-based superalloy in a laser powder bed fusion additive manufacturing process. Thermal modeling by finite element analysis simulates the laser melt pool, with surface temperatures in agreement with in situ thermographic measurements on Inconel 625. Geometric and thermal features of the simulated melt pools are extracted and used in subsequent mesoscale simulations. Solidification in the melt pool is simulated on two length scales. For the multicomponent a…
Selective laser melting (SLM) is rapidly evolving to become a mainstream technology. However, the fundamental mechanisms of solidification and microstructure development inherent to the non-equilibrium conditions of this additive manufacturing method, which differ largely from those typical of conventional processing techniques, remain widely unknown. In this work, an in-depth characterization of the microstructure of Al7075 SLM processed samples, built from powder mixtures containing ZrH2 microparticles, demonstrates the occurrence of icosahedral quasicrystal-enhanced nucleation during laser …
Ni-rich $γ$ cells and Nb-rich eutectic droplets that form during laser power bed fusion solidification of Ni-Nb alloys are studied using experiments and simulations. Finite element simulations estimate the cooling rates in the melt pool and phase-field simulations predict the resulting cellular microstructures. The cell and droplet spacings are determined as a function of cooling rate and fit to a power law. The formation of Laves phase is predicted for a critical composition of Nb in the liquid droplets. Finally, our simulations demonstrate that anisotropy in the $γ$ orientation influences th…
Full pattern Le-Bail refinement using x-ray powder diffraction profiles of Sr1-xCaxTiO3 for x=0.02, 0.04 in the temperature range 12 to 300 K reveals anomalies in the unit cell parameters at 170, 225 K due to an antiferrodistortive (cubic to tetragonal I4/mcm) phase transition and at ~32, ~34 K due to a transition to a polar phase (tetragonal I4/mcm to orthorhombic Ic2m), respectively. The lower transition temperatures obtained by us are in excellent agreement with those reported on the basis of the dielectric studies by Bednorz and Muller, [10] who attributed these to ferroelectric transition…
