A simple method is proposed for use in a scenario involving a single-antenna source node communicating with a destination node that is equipped with two antennas via multiple single-antenna relay nodes, where each relay is subject to an individual power constraint. Furthermore, ultra-reliable and low-latency communication are desired. The latter requirement translates to considering only schemes that make use of local channel state information. Whereas for a receiver equipped with a single antenna, distributed beamforming is a well known and adequate solution, no straightforward extension is known. In this paper, a scheme is proposed based on a space-time diversity transformation that is applied as a front-end operation at the destination node. This results in an effective unitary channel matrix replacing the scalar coefficient corresponding to each user. Each relay node then inverts its associated channel matrix, which is the generalization of undoing the channel phase in the classical case of distributed beamforming to a single-antenna receiver, and then repeats the message over the resulting "gain-only" channel. In comparison to a single-antenna destination node, the method doubles the diversity order without requiring any channel state information at the receiver while at the same time retaining the array gain offered by the relays.
We present and analyze the performance of constellation precoded beamforming. This multi-input multi-output transmission technique is based on the singular value decomposition of a channel matrix. In this work, the beamformer is precoded to improve its diversity performance. It was shown previously that while single beamforming achieves full diversity without channel coding, multiple beamforming results in diversity loss. In this paper, we show that a properly designed constellation precoder makes uncoded multiple beamforming achieve full diversity order. We also show that partially precoded m…
Consider a simple two-way relaying channel where two single-antenna sources exchange information via a multiple-antenna relay. To such a scenario, all the existing works which can achieve full diversity order are based on the antenna/relay selection, where the difficulty to design the beamforming lies in the fact that a single beamformer needs to serve two destinations. In this paper, we propose a new full-diversity beamforming scheme which ensures that the relay signals are coherently combined at both destinations. Both analytical and numerical results are provided to demonstrate that this pr…
Classical beamforming techniques rely on highly linear transmitters and receivers to allow phase-coherent combining at the transmitter and receiver. The transmitter uses beamforming to steer signal power towards the receiver, and the receiver uses beamforming to gather and coherently combine the signals from multiple receiver antennas. When the transmitters and receivers are instead constrained for power and cost reasons to be non-linear one-bit devices, the potential advantages and performance metrics associated with beamforming are not as well understood. We define beamforming at the transmi…
For broadband wireless communication systems, Orthogonal Frequency Division Multiplexing (OFDM) has been combined with Multi-Input Multi-Output (MIMO) techniques. Bit-Interleaved Coded Multiple Beamforming (BICMB) can achieve both spatial diversity and spatial multiplexing for flat fading MIMO channels. For frequency selective fading MIMO channels, BICMB with OFDM (BICMB-OFDM) can be applied to achieve both spatial diversity and multipath diversity, making it an important technique. However, analyzing the diversity of BICMB-OFDM is a challenging problem. In this paper, the diversity analysis o…
In this paper, we present the diversity order analysis of bit-interleaved coded multiple beamforming (BICMB) combined with the constellation precoding scheme. Multiple beamforming is realized by singular value decomposition of the channel matrix which is assumed to be perfectly known to the transmitter as well as the receiver. Previously, BICMB is known to have a diversity order bound related with the product of the code rate and the number of parallel subchannels, losing the full diversity order in some cases. In this paper, we show that BICMB combined with the constellation precoder and maxi…
A joint robust transmit/receive adaptive beamforming for multiple-input multipleoutput (MIMO) radar based on probability-constrained optimization approach is developed in the case of Gaussian and arbitrary distributed mismatch present in both the transmit and receive signal steering vectors. A tight lower bound of the probability constraint is also derived by using duality theory. The formulated probability-constrained robust beamforming problem is nonconvex and NP-hard. However, we reformulate its cost function into a bi-quadratic function while the probability constraint splits into transmit…
Medium-scale or large-scale receive antenna array with digital beamforming can be employed at receiver to make a significant interference reduction, but leads to expensive cost and high complexity of the RF-chain circuit. To deal with this issue, a classic analog-and-digital beamforming (ADB) structure was proposed in the literature for greatly reducing the number of RF-chains. Based on the ADB structure, we in this paper propose a robust hybrid ADB scheme to resist directions of arrival (DOAs) estimation errors. The key idea of our scheme is to employ null space projection (NSP) in analog bea…
In this paper, diversity analysis of bit-interleaved coded multiple beamforming (BICMB) is extended to the case of general spatial interleavers, removing a condition on their previously known design criteria and quantifying the resulting diversity order. The diversity order is determined by a parameter Qmax which is inherited from the convolutional code and the spatial de-multiplexer used in BICMB. We introduce a method to find this parameter by employing a transfer function approach as in finding the weight spectrum of a convolutional code. By using this method, several Qmax values are shown …
Multi-Input Multi-Output (MIMO) techniques have been incorporated with Orthogonal Frequency Division Multiplexing (OFDM) for broadband wireless communication systems. Bit-Interleaved Coded Multiple Beamforming (BICMB) can achieve both spatial diversity and spatial multiplexing for flat fading MIMO channels. For frequency selective fading MIMO channels, BICMB with OFDM (BICMB-OFDM) can be employed to provide both spatial diversity and multipath diversity, making it an important technique. In our previous work, the subcarrier grouping technique was applied to combat the negative effect of subcar…
Multiple antenna techniques that allow energy beamforming have been looked upon as a possible candidate for increasing the transfer efficiency between the energy transmitter (ET) and the energy receiver (ER) in wireless power transfer. This paper introduces a novel scheme that facilitates energy beamforming by utilizing Received Signal Strength Indicator (RSSI) values to estimate the channel. Firstly, in the training stage, the ET will transmit using each beamforming vector in a codebook, which is pre-defined using a Cramer-Rao lower bound analysis. RSSI value corresponding to each beamforming…
In this paper, a new receiver structure that is intended to detect the signals from multiple adjacent satellites in the presence of other interfering satellites is proposed. We tackle the worst case interference conditions, i.e., it is assumed that uncoded signals that fully overlap in frequency arrive at a multiple-element small-size parabolic antenna in a spatially correlated noise environment. The proposed successive interference cancellation (SIC) receiver, denoted by SIC Hy/ML, employs hybrid beamforming and disjoint maximum likelihood (ML) detection. Depending on the individual signals s…
We propose, analyze and demonstrate an architecture for scalable cooperative reception. In a cluster of N + 1 receive nodes, one node is designated as the final receiver, and the N other nodes act as amplify-and-forward relays which adapt their phases such that the relayed signals add up constructively at the designated receiver. This yields received SNR scaling linearly with N, while avoiding the linear increase in overhead incurred by a direct approach in which received signals are separately quantized and transmitted for centralized processing. By transforming the task of long-distance dist…
Motivated by massive deployment of low data rate Internet of things (IoT) and ehealth devices with requirement for highly reliable communications, this paper proposes receive beamforming techniques for the uplink of a single-input multiple-output (SIMO) multiple access channel (MAC), based on a per-user probability of error metric and one-dimensional signalling. Although beamforming by directly minimizing probability of error (MPE) has potential advantages over classical beamforming methods such as zero-forcing and minimum mean square error beamforming, MPE beamforming results in a non-convex …
This paper investigates the optimal transmit beamforming design of simultaneous wireless information and power transfer (SWIPT) in the multiuser multiple-input-single-output (MISO) downlink with specific absorption rate (SAR) constraints. We consider the power splitting technique for SWIPT, where each receiver divides the received signal into two parts: one for information decoding and the other for energy harvesting with a practical non-linear rectification model. The problem of interest is to maximize as much as possible the received signal-to-interference-plus-noise ratio (SINR) and the ene…
This paper studies a multi-user multiple-input single-output (MISO) downlink system for simultaneous wireless information and power transfer (SWIPT), in which a set of single-antenna mobile stations (MSs) receive information and energy simultaneously via power splitting (PS) from the signal sent by a multi-antenna base station (BS). We aim to minimize the total transmission power at BS by jointly designing transmit beamforming vectors and receive PS ratios for all MSs under their given signal-to-interference-plus-noise ratio (SINR) constraints for information decoding and harvested power const…
For a multi-user interference channel with multi-antenna transmitters and single-antenna receivers, by restricting each receiver to a single-user detector, computing the largest achievable rate region amounts to solving a family of non-convex optimization problems. Recognizing the intrinsic connection between the signal power at the intended receiver and the interference power at the unintended receiver, the original family of non-convex optimization problems is converted into a new family of convex optimization problems. It is shown that, for such interference channels with each receiver impl…
We study quantized beamforming in wireless amplify-and-forward relay-interference networks with any number of transmitters, relays, and receivers. We design the quantizer of the channel state information to minimize the probability that at least one receiver incorrectly decodes its desired symbol(s). Correspondingly, we introduce a generalized diversity measure that encapsulates the conventional one as the first-order diversity. Additionally, it incorporates the second-order diversity, which is concerned with the transmitter power dependent logarithmic terms that appear in the error rate expre…
The Golden Code is a full-rate full-diversity space-time code, which achieves maximum coding gain for Multiple-Input Multiple-Output (MIMO) systems with two transmit and two receive antennas. Since four information symbols taken from an M-QAM constellation are selected to construct one Golden Code codeword, a maximum likelihood decoder using sphere decoding has the worst-case complexity of O(M^4), when the Channel State Information (CSI) is available at the receiver. Previously, this worst-case complexity was reduced to O(M^(2.5)) without performance degradation. When the CSI is known by the t…
For a multi-user interference channel with multi-antenna transmitters and single-antenna receivers, by restricting each transmitter to Gaussian input and each receiver to a single-user detector, computing the largest achievable rate region amounts to solving a family of non-convex optimization problems. Recognizing the intrinsic connection between the signal power at the intended receiver and the interference power at the unintended receiver, the original family of non-convex optimization problems is converted into a new family of convex optimization problems. It is shown that, for such interf…
Multiple antenna systems have been extensively used by standards designing multi-gigabit communication systems operating in bandwidth of several GHz. In this paper, we study the use of transmitter (Tx) beamforming techniques to improve the performance of a MIMO system with a low precision ADC. We motivate an approach to use eigenmode transmit beamforming (which imposes a diagonal structure in the complete MIMO system) and use an eigenmode power allocation which minimizes the uncoded BER of the finite precision system. Although we cannot guarantee optimality of this approach, we observe that ev…
Beamforming techniques that employ Singular Value Decomposition (SVD) are commonly used in Multi-Input Multi-Output (MIMO) wireless communication systems. In the absence of channel coding, when a single symbol is transmitted, these systems achieve the full diversity order provided by the channel; whereas when multiple symbols are simultaneously transmitted, this property is lost. When channel coding is employed, full diversity order can be achieved. For example, when Bit-Interleaved Coded Modulation (BICM) is combined with this technique, full diversity order of NM in an MxN MIMO channel trans…
Hybrid analog and digital (HAD) beamforming has been recently receiving considerable deserved attention for a practical implementation on the large-scale antenna systems. As compared to full digital beamforming, partial-connected HAD beamforming can significantly reduce the hardware cost, complexity, and power consumption. In this paper, in order to mitigate the jamming along with lowering the hardware complexity and cost by reducing the number of RF chains needed, a novel hybrid analog and digital receive beamformer based on an improved bat algorithm (I-BA) and the phase-only is proposed. Our…
Intelligent reflecting surface (IRS) has emerged as a cost-effective solution to enhance wireless communication performance via passive signal reflection. Existing works on IRS have mainly focused on investigating IRS's passive beamforming/reflection design to boost the communication rate for users assuming that their channel state information (CSI) is fully or partially known. However, how to exploit IRS to improve the wireless transmission reliability without any CSI, which is typical in high-mobility/delay-sensitive communication scenarios, remains largely open. In this paper, we study a ne…
As more and more people choose high-speed rail (HSR) as a means of transportation for short trips, there is ever growing demand of high quality of multimedia services. With its rich spectrum resources, millimeter wave (mm-wave) communications can satisfy the high network capacity requirements for HSR. Also, it is possible for receivers (RXs) to be equipped with antenna arrays in mm-wave communication systems due to its short wavelength. However, as HSRs run with high speed, the received signal power (RSP) varies rapidly over a cell and it is the lowest at the edge of the cell compared to other…
Massive number of internet of things (IoT) devices are expected to simultaneously connect to the mMTC and beyond future generations of wireless network, posing severe challenge to aspects such as RACH procedure, user equipment detection and channel estimation. Although spatial combining has provided significant gains in conventional grant-based transmission, this technique is stuck in dilemma when it comes to autonomous grant-free transmission tailored for IoT use cases. To address this, blind spatial combining and its incorporation in the data-only MUD are elaborated in this paper answering t…
We consider settings in which T multi-antenna transmitters and K single-antenna receivers concurrently utilize the available communication resources. Each transmitter sends useful information only to its intended receivers and can degrade the performance of unintended systems. Here, we assume the performance measures associated with each receiver are monotonic with the received power gains. In general, the systems' joint operation is desired to be Pareto optimal. However, designing Pareto optimal resource allocation schemes is known to be difficult. In order to reduce the complexity of achievi…
A novel transmission protocol is conceived for a multi-user, multi-relay, multiple-input--multiple-output orthogonal frequency-division multiple-access (MIMO-OFDMA) cellular network based on joint transmit and receive beamforming. More specifically, the network's MIMO channels are mathematically decomposed into several effective multiple-input--single-output (MISO) channels, which are spatially multiplexed for transmission. For the sake of improving the attainable capacity, these MISO channels are grouped using a pair of novel grouping algorithms, which are then evaluated in terms of their per…
In this paper, we propose an adaptive coordinated Tx-Rx beamforming scheme for inter-user interference cancellation, when a base station (BS) communicates with multiple users that each has multiple receive antennas. The conventional coordinated Tx-Rx beamforming scheme transmits a fixed number of data streams for each user regardless of the instantaneous channel states, that is, all the users, no matter they are with ill-conditioned or well-conditioned channels, have the same number of data streams. However, in the proposed adaptive coordinated Tx-Rx beamforming scheme, we adaptively select th…
In this work, we study the achievable rate and the energy efficiency of Analog, Hybrid and Digital Combining (AC, HC and DC) for millimeter wave (mmW) receivers. We take into account the power consumption of all receiver components, not just Analog-to-Digital Converters (ADC), determine some practical limitations of beamforming in each architecture, and develop performance analysis charts that enable comparison of different receivers simultaneously in terms of two metrics, namely, Spectral Efficiency (SE) and Energy Efficiency (EE). We present a multi-objective utility optimization interpretat…
We consider a multiuser multiple-input single-output interference channel where the receivers are characterized by both quality-of-service (QoS) and radio-frequency (RF) energy harvesting (EH) constraints. We consider the power splitting RF-EH technique where each receiver divides the received signal into two parts a) for information decoding and b) for battery charging. The minimum required power that supports both the QoS and the RF-EH constraints is formulated as an optimization problem that incorporates the transmitted power and the beamforming design at each transmitter as well as the pow…
For 5G it will be important to leverage the available millimeter wave spectrum. To achieve an approximately omni- directional coverage with a similar effective antenna aperture compared to state of the art cellular systems, an antenna array is required at both the mobile and basestation. Due to the large bandwidth and inefficient amplifiers available in CMOS for mmWave, the analog front-end of the receiver with a large number of antennas becomes especially power hungry. Two main solutions exist to reduce the power consumption: Hybrid BeamForming (HBF) and Digital BeamForming (DBF) with low res…
When the Channel State Information (CSI) is known by both the transmitter and the receiver, beamforming techniques employing Singular Value Decomposition (SVD) are commonly used in Multiple-Input Multiple-Output (MIMO) systems. Without channel coding, there is a trade-off between full diversity and full multiplexing. When channel coding is added, both of them can be achieved as long as the code rate Rc and the number of employed subchannels S satisfy the condition RcS<=1. By adding a properly designed constellation precoder, both full diversity and full multiplexing can be achieved for both un…
In this study, we analyze the codebook design used for analog beamforming. Analog beamforming and combining suffer from a subspace sampling limitation, that is, the receiver cannot directly observe the channel coefficients; instead, the receiver observes a noisy version of their weighted combination. To resolve this, the transmitter and the receiver usually collaborate to determine the best beamformer combiner pair during the beam-sweeping process. This is done by evaluating a limited number of codewords chosen from a pre-defined codebook. In this study, we propose a new framework inspired by …
In this paper we carry out the asymptotic diversity analysis for millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems by using bit interleaved coded multiple beamforming (BICMB). First, a single-user mmWave system which employs $M_t$ antenna subarrays at the transmitter and $M_r$ antenna subarrays at the receiver is studied. Each antenna subarray in the transmitter and the receiver has $N_r$ and $N_t$ antennas, respectively. We establish a theorem for the diversity gain when the number of antennas in each remote antenna unit (RAU) goes to infinity. Based on the theore…
In this paper, we propose a two-stage analog combining architecture for millimeter wave (mmWave) communications with hybrid analog/digital beamforming and low-resolution analog-to-digital converters (ADCs). We first derive a two-stage combining solution by solving a mutual information (MI) maximization problem without a constant modulus constraint on analog combiners. With the derived solution, the proposed receiver architecture splits the analog combining into a channel gain aggregation stage followed by a spreading stage to maximize the MI by effectively managing quantization error. We show …
In order to address the asynchronous interference issue for a generalized scenario with multiple primary and multiple secondary receivers, in this paper, we propose an innovative cooperative beamforming technique. In particular, the cooperative beamforming design is formulated as an optimization problem that maximizes the weighted sum achievable transmission rate of secondary destinations while it maintains the asynchronous interferences at the primary receivers below their target thresholds. In light of the intractability of the problem, we propose a two-phase suboptimal cooperative beamformi…
This paper examines linear beamforming methods for secure communications in a multiuser wiretap channel with a single transmitter, multiple legitimate receivers, and a single eavesdropper, where all nodes are equipped with multiple antennas. No information regarding the eavesdropper is presumed at the transmitter, and we examine both the broadcast MIMO downlink with independent information, and the multicast MIMO downlink with common information for all legitimate receivers. In both cases the information signal is transmitted with just enough power to guarantee a certain SINR at the desired re…
This letter investigates bit-interleaved coded multiple beamforming (BICMB) with perfect coding in millimeter-wave (mm-wave) massive multiple-input multiple-output (MIMO) systems to achieve both maximum diversity gain and multiplexing gain. Using perfect coding with BICMB enables us to do this. We show that by using BICMB and perfect coding, the diversity gain becomes independent from the number of transmitted data streams and the number of antennas in each remote antenna unit (RAU) at the transmitter and the receiver. The assumption is that the perfect channel state information (CSI) is known…
The random beamforming (RBF) scheme, jointly applied with multi-user diversity based scheduling, is able to achieve virtually interference-free downlink transmissions with only partial channel state information (CSI) available at the transmitter. However, the impact of receive spatial diversity on the rate performance of RBF is not fully characterized yet even in a single-cell setup. In this paper, we study a multi-cell multiple-input multiple-output (MIMO) broadcast system with RBF applied at each base station (BS) and either the minimum-mean-square-error (MMSE), matched filter (MF), or anten…
We propose a location-based beamforming scheme for wiretap channels, where a source communicates with a legitimate receiver in the presence of an eavesdropper. We assume that the source and the eavesdropper are equipped with multiple antennas, while the legitimate receiver is equipped with a single antenna. We also assume that all channels are in a Rician fading environment, the channel state information from the legitimate receiver is perfectly known at the source, and that the only information on the eavesdropper available at the source is her location. We first describe how the beamforming …
We consider the full-duplex (FD) two-way amplify-and-forward relay system with imperfect cancelation of loopback self-interference (SI) and investigate joint design of relay and receive beamforming for minimizing the mean square error under a relay transmit power constraint. Due to loopback channel estimation error and limitation of analog-to-digital converter, the loopback SI cannot be completely canceled. Multiple antennas at the relay can help loopback SI suppression but beamforming is required to balance between the residual SI suppression and the desired signal transmission. Moreover, the…
A receiver with perfect channel state information (CSI) in a point-to-point multiple-input multiple-output (MIMO) channel can compute the transmit beamforming vector that maximizes the transmission rate. For frequency-division duplex, a transmitter is not able to estimate CSI directly and has to obtain a quantized transmit beamforming vector from the receiver via a rate-limited feedback channel. We assume that time evolution of MIMO channels is modeled as a Gauss-Markov process parameterized by a temporal-correlation coefficient. Since feedback rate is usually low, we assume rank-one transmit …
In this paper, we investigate a multiple-input multiple-output (MIMO) system with simultaneous information detection (ID) and energy harvesting (EH) receiver. This point-to-point system operates in the vicinity of active interfering nodes. The receiver performs power splitting where a portion of received signal undergoes analog energy harvesting circuitry. Further, the information content of the other portion is extracted after performing digital beamforming. In this MIMO system, information carrier eigen-modes are not necessarily the eigen-modes with the strongest energy level. Hence, it is b…
In this letter, we study a new technique for energy beamforming (EB) in multi-user networks, which combines large antenna retrodirectivity at the transmitter side with signal backscattering at the energy receivers. The proposed technique has low complexity and achieves EB without any active operation at the receivers or complicated signal processing techniques at the transmitter. Since the average harvested energy depends on the backscattering coefficients, we investigate different reflection policies for various design objectives. The proposed policies are analyzed from a system level standpo…
We consider decentralized multi-antenna cognitive radio networks where secondary (cognitive) users are granted simultaneous spectrum access along with license-holding (primary) users. We treat the problem of distributed beamforming and rate allocation for the secondary users such that the minimum weighted secondary rate is maximized. Such an optimization is subject to (1) a limited weighted sum-power budget for the secondary users and (2) guaranteed protection for the primary users in the sense that the interference level imposed on each primary receiver does not exceed a specified level. Base…
At millimeter wave (mmW) frequencies, beamforming and large antenna arrays are an essential requirement to combat the high path loss for mmW communication. Moreover, at these frequencies, very large bandwidths are available to fulfill the data rate requirements of future wireless networks. However, utilization of these large bandwidths and of large antenna arrays can result in a high power consumption which is an even bigger concern for mmW receiver design. In a mmW receiver, the analog-to-digital converter (ADC) is generally considered as the most power consuming block. In this paper, primari…
An energy-efficient opportunistic collaborative beamformer with one-bit feedback is proposed for ad hoc sensor networks over Rayleigh fading channels. In contrast to conventional collaborative beamforming schemes in which each source node uses channel state information to correct its local carrier offset and channel phase, the proposed beamforming scheme opportunistically selects a subset of source nodes whose received signals combine in a quasi-coherent manner at the intended receiver. No local phase-precompensation is performed by the nodes in the opportunistic collaborative beamformer. As a…
In this paper, we consider fast wireless data aggregation via over-the-air computation (AirComp) in Internet of Things (IoT) networks, where an access point (AP) with multiple antennas aim to recover the arithmetic mean of sensory data from multiple IoT devices. To minimize the estimation distortion, we formulate a mean-squared-error (MSE) minimization problem that involves the joint optimization of the transmit scalars at the IoT devices as well as the denoising factor and the receive beamforming vector at the AP. To this end, we derive the transmit scalars and the denoising factor in closed-…
Analog beamforming greatly reduces the implementation cost of massive antenna transceivers by using only one up/down-conversion chain. However, it incurs a large pilot overhead when used with conventional channel estimation (CE) techniques. This is because these CE techniques involve digital processing, requiring the up/down-conversion chain to be time-multiplexed across the antenna dimensions. This paper introduces a novel CE technique, called continuous analog channel estimation (CACE), that avoids digital processing, enables analog beamforming at the receiver and additionally provides resil…
Magnetic induction (MI) based communication and power transfer systems have gained an increased attention in the recent years. Typical applications for these systems lie in the area of wireless charging, near-field communication, and wireless sensor networks. For an optimal system performance, the power efficiency needs to be maximized. Typically, this optimization refers to the impedance matching and tracking of the split-frequencies. However, an important role of magnitude and phase of the input signal has been mostly overlooked. Especially for the wireless power transfer systems with multip…
We study distributed algorithms for adjusting beamforming vectors and receiver filters in multiple-input multiple-output (MIMO) interference networks, with the assumption that each user uses a single beam and a linear filter at the receiver. In such a setting there have been several distributed algorithms studied for maximizing the sum-rate or sum-utility assuming perfect channel state information (CSI) at the transmitters and receivers. The focus of this paper is to study adaptive algorithms for time-varying channels, without assuming any CSI at the transmitters or receivers. Specifically, we…
The focus of this paper is on beamforming in a millimeter-wave (mmW) multi-input multi-output (MIMO) setup that has gained increasing traction in meeting the high data-rate requirements of next-generation wireless systems. For a given MIMO channel matrix, the optimality of beamforming with the dominant right-singular vector (RSV) at the transmit end and with the matched filter to the RSV at the receive end has been well-understood. When the channel matrix can be accurately captured by a physical (geometric) scattering model across multiple clusters/paths as is the case in mmW MIMO systems, we …
This paper studies the wireless two-way relay channel (TWRC), where two source nodes, S1 and S2, exchange information through an assisting relay node, R. It is assumed that R receives the sum signal from S1 and S2 in one time-slot, and then amplifies and forwards the received signal to both S1 and S2 in the next time-slot. By applying the principle of analogue network (ANC), each of S1 and S2 cancels the so-called "self-interference" in the received signal from R and then decodes the desired message. Assuming that S1 and S2 are each equipped with a single antenna and R with multi-antennas, thi…
Simultaneous wireless information and power transfer (SWIPT) is anticipated to have abundant applications in future machine or sensor based wireless networks by providing wireless data and energy access at the same time. In this paper, we study a multiuser multiple-input single-output (MISO) broadcast SWIPT system, where a multi-antenna access point (AP) sends information and energy simultaneously via spatial multiplexing to multiple single-antenna receivers each of which implements information decoding (ID) or energy harvesting (EH). Since EH receivers in practice operate with considerably hi…
We consider a two-way relay network, where two source nodes, S1 and S2, exchange information through a cluster of relay nodes. The relay nodes receive the sum signal from S1 and S2 in the first time slot. In the second time slot, each relay node multiplies its received signal by a complex coefficient and retransmits the signal to the two source nodes, which leads to a distributed two-way beamforming system. By applying the principle of analog network coding, each receiver at S1 and S2 cancels the ``self-interference'' in the received signal from the relay cluster and decodes the message. This …
An analysis of the diversity gain for bit-interleaved coded multiple beamforming (BICMB) method in millimeter-wave (mm-Wave) massive multiple-input multiple-output (MIMO) systems is carried out for both the single-user and multi-user scenario. We show that the diversity gain is independent of the number of data streams and full spatial multiplexing order can be achieved in both scenarios. Also, we show that the diversity gain in the multi-user scenario is independent of the number of users in the system and only depends on the number of the remote antenna units (RAUs) at the transmitter side, …
We consider a two-way relay network, where two source nodes, S1 and S2, exchange information through a cluster of relay nodes. The relay nodes receive the sum signal from S1 and S2 in the first time slot. In the second time slot, each relay node multiplies its received signal by a complex coefficient and retransmits the signal to the two source nodes, which leads to a collaborative two-way beamforming system. By applying the principle of analog network coding, each receiver at S1 and S2 cancels the "self-interference" in the received signal from the relay cluster and decodes the message. This …
We consider a fading channel in which a multi-antenna transmitter communicates with a multi-antenna receiver through a reconfigurable intelligent surface (RIS) that is made of $N$ reconfigurable passive scatterers impaired by phase noise. The beamforming vector at the transmitter, the combining vector at the receiver, and the phase shifts of the $N$ scatterers are optimized in order to maximize the signal-to-noise-ratio (SNR) at the receiver. By assuming Rayleigh fading (or line-of-sight propagation) on the transmitter-RIS link and Rayleigh fading on the RIS-receiver link, we prove that the SN…
