A receiver with perfect channel state information (CSI) in a point-to-point multiple-input multiple-output (MIMO) channel can compute the transmit beamforming vector that maximizes the transmission rate. For frequency-division duplex, a transmitter is not able to estimate CSI directly and has to obtain a quantized transmit beamforming vector from the receiver via a rate-limited feedback channel. We assume that time evolution of MIMO channels is modeled as a Gauss-Markov process parameterized by a temporal-correlation coefficient. Since feedback rate is usually low, we assume rank-one transmit beamforming or transmission with single data stream. For given feedback rate, we analyze the optimal feedback interval that maximizes the average received power of the systems with two transmit or two receive antennas. For other system sizes, the optimal feedback interval is approximated by maximizing the rate difference in a large system limit. Numerical results show that the large system approximation can predict the optimal interval for finite-size system quite accurately. Numerical results also show that quantizing transmit beamforming with the optimal feedback interval gives larger rate than the existing Kalman-filter scheme does by as much as 10% and than feeding back for every block does by 44% when the number of feedback bits is small.
Feedback of quantized channel state information (CSI), called limited feedback, enables transmit beamforming in multiple-input-multiple-output (MIMO) wireless systems with a small amount of overhead. Due to its efficiency, beamforming with limited feedback has been adopted in several wireless communication standards. Prior work on limited feedback commonly adopts the block fading channel model where temporal correlation in wireless channels is neglected. This paper considers temporally-correlated channels and designs single-user transmit beamforming with limited feedback. Analytical results co…
Classical beamforming techniques rely on highly linear transmitters and receivers to allow phase-coherent combining at the transmitter and receiver. The transmitter uses beamforming to steer signal power towards the receiver, and the receiver uses beamforming to gather and coherently combine the signals from multiple receiver antennas. When the transmitters and receivers are instead constrained for power and cost reasons to be non-linear one-bit devices, the potential advantages and performance metrics associated with beamforming are not as well understood. We define beamforming at the transmi…
A joint robust transmit/receive adaptive beamforming for multiple-input multipleoutput (MIMO) radar based on probability-constrained optimization approach is developed in the case of Gaussian and arbitrary distributed mismatch present in both the transmit and receive signal steering vectors. A tight lower bound of the probability constraint is also derived by using duality theory. The formulated probability-constrained robust beamforming problem is nonconvex and NP-hard. However, we reformulate its cost function into a bi-quadratic function while the probability constraint splits into transmit…
This is a companion technical report of the main manuscript "Physical-Layer Multicasting by Stochastic Transmit Beamforming and Alamouti Space-Time Coding". The report serves to give detailed derivations of the achievable rate functions encountered in the main manuscript, which are too long to be included in the latter. In addition, more simulation results are presented to verify the viability of the multicast schemes developed in the main manuscript.
In this letter, we propose a blockwise phase rotation-aided analog transmit beamforming (BPR-ATB) scheme to improve the spectral efficiency and the bit-error-rate (BER) performance in millimeter wave (mmWave) communication systems. Due to the phase angle optimization issues of the conventional analog beamforming, we design the BPR-ATB for reducing the rotated beamspace of the equivalent channel and improving the minimum Euclidean distance. To verify the effectiveness of the proposed BPR-ATB scheme, we employ an Alamouti coding technique at the transmitter and evaluate the bit-error-rate perfor…
Transmit beamforming is a versatile technique for signal transmission from an array of $N$ antennas to one or multiple users [1]. In wireless communications, the goal is to increase the signal power at the intended user and reduce interference to non-intended users. A high signal power is achieved by transmitting the same data signal from all antennas, but with different amplitudes and phases, such that the signal components add coherently at the user. Low interference is accomplished by making the signal components add destructively at non-intended users. This corresponds mathematically to de…
This paper studies a multi-user multiple-input single-output (MISO) downlink system for simultaneous wireless information and power transfer (SWIPT), in which a set of single-antenna mobile stations (MSs) receive information and energy simultaneously via power splitting (PS) from the signal sent by a multi-antenna base station (BS). We aim to minimize the total transmission power at BS by jointly designing transmit beamforming vectors and receive PS ratios for all MSs under their given signal-to-interference-plus-noise ratio (SINR) constraints for information decoding and harvested power const…
This paper studies a downlink multiuser transmit beamforming design under spherical channel uncertainties, using a worst-case robust formulation. This robust design problem is nonconvex. Recently, a convex approximation formulation based on semidefinite relaxation (SDR) has been proposed to handle the problem. Curiously, simulation results have consistently indicated that SDR can attain the global optimum of the robust design problem. This paper intends to provide some theoretical insights into this important empirical finding. Our main result is a dual representation of the SDR formulation, w…
Recently, robust transmit beamforming has drawn considerable attention because it can provide guaranteed receiver performance in the presence of channel state information (CSI) errors. Assuming complex Gaussian distributed CSI errors, this paper investigates the robust beamforming design problem that minimizes the transmission power subject to probabilistic signal-to-interference-plus-noise ratio (SINR) constraints. The probabilistic SINR constraints in general have no closed-form expression and are difficult to handle. Based on a Bernstein-type inequality of complex Gaussian random variables,…
Cooperative beamforming (CB) has been proposed as a special case of coordinated multi-point techniques in wireless communications. In wireless sensor networks, CB can enable low power communication by allowing a collection of sensor nodes to transmit data simultaneously to a distant fusion center in one hop. Besides the traditional CB approach where all nodes need to share and transmit the same data, a more recent technique allows each node to transmit its own data while still achieving the benefits of cooperation. However, the intricacies of varying beamforming gains in the direct sequence sp…
A simple feedback control algorithm is presented for distributed beamforming in a wireless network. A network of wireless sensors that seek to cooperatively transmit a common message signal to a Base Station (BS) is considered. In this case, it is well-known that substantial energy efficiencies are possible by using distributed beamforming. The feedback algorithm is shown to achieve the carrier phase coherence required for beamforming in a scalable and distributed manner. In the proposed algorithm, each sensor independently makes a random adjustment to its carrier phase. Assuming that the BS i…
Simultaneous multiuser beamforming in multiantenna downlink channels can entail dirty paper (DP) precoding (optimal and high complexity) or linear precoding (suboptimal and low complexity) approaches. The system performance is typically characterized by the sum capacity with homogenous users with perfect channel state information at the transmitter. The sum capacity performance analysis requires the exact probability distributions of the user signal-to-noise ratios (SNRs) or signal-to-interference plus noise ratios (SINRs). The standard techniques from order statistics can be sufficient to obt…
With finite-rate feedback, we propose two feedback methods for transmit beamforming in a point-to-point MISO-OFDM channel. For the first method, a receiver with perfect channel information, quantizes and feeds back the optimal transmit beamforming vectors of a few selected subcarriers, which are equally spaced. Based on those quantized vectors, the transmitter applies either constant, linear, or higher-order interpolation with the remaining beamforming vectors. With constant interpolation, we derive the approximate sum achievable rate and the optimal cluster size that maximizes the approximate…
We consider $K$ links operating concurrently in the same spectral band. Each transmitter has multiple antennas, while each receiver uses a single antenna. This setting corresponds to the multiple-input single-output interference channel. We assume perfect channel state information at the single-user decoding receivers whereas the transmitters only have estimates of the true channels. The channel estimation errors are assumed to be bounded in elliptical regions whose geometry is known at the transmitters. Robust beamforming optimizes worst-case received power gains, and a Pareto optimal point i…
This paper introduces novel transmit beamforming approaches for the cognitive radio (CR) Z-channel. The proposed transmission schemes exploit non-causal information about the interference at the SBS to re-design the CR beamforming optimization problem. This is done with the objective to improve the quality of service (QoS) of secondary users by taking advantage of constructive interference in the secondary link. The beamformers are designed to minimize the worst secondary user's symbol error probability (SEP) under constraints on the instantaneous total transmit power, and the power of the ins…
Multiple antenna systems have been extensively used by standards designing multi-gigabit communication systems operating in bandwidth of several GHz. In this paper, we study the use of transmitter (Tx) beamforming techniques to improve the performance of a MIMO system with a low precision ADC. We motivate an approach to use eigenmode transmit beamforming (which imposes a diagonal structure in the complete MIMO system) and use an eigenmode power allocation which minimizes the uncoded BER of the finite precision system. Although we cannot guarantee optimality of this approach, we observe that ev…
In this paper, an IRS-aided integrated sensing and communications (ISAC) system operating in the terahertz (THz) band is proposed to maximize the system capacity. Transmit beamforming and phase-shift design are transformed into a universal optimization problem with ergodic constraints. Then the joint optimization of transmit beamforming and phase-shift design is achieved by gradient-based, primal-dual proximal policy optimization (PPO) in the multi-user multiple-input single-output (MISO) scenario. Specifically, the actor part generates continuous transmit beamforming and the critic part takes…
This paper investigates the optimal transmit beamforming design of simultaneous wireless information and power transfer (SWIPT) in the multiuser multiple-input-single-output (MISO) downlink with specific absorption rate (SAR) constraints. We consider the power splitting technique for SWIPT, where each receiver divides the received signal into two parts: one for information decoding and the other for energy harvesting with a practical non-linear rectification model. The problem of interest is to maximize as much as possible the received signal-to-interference-plus-noise ratio (SINR) and the ene…
Consider transceiver designs in a multiuser multi-input single-output (MISO) downlink channel, where the users are to receive the same data stream simultaneously. This problem, known as physical-layer multicasting, has drawn much interest. Presently, a popularized approach is transmit beamforming, in which the beamforming optimization is handled by a rank-one approximation method called semidefinite relaxation (SDR). SDR-based beamforming has been shown to be promising for a small or moderate number of users. This paper describes two new transceiver strategies for physical-layer multicasting. …
The cost of radio frequency (RF) chains is the biggest drawback of massive MIMO millimeter wave networks. By employing spatial modulation (SM), it is possible to implement lower number of RF chains than transmit antennas but still achieve high spectral efficiency. In this work, we propose a system model of the SM scheme together with hybrid beamforming at the transmitter and digital combining at the receiver. In the proposed model, spatially-modulated bits are mapped onto indices of antenna arrays. It is shown that the proposed model achieves approximately 5dB gain over classical multi-user SM…
A novel transmission protocol is conceived for a multi-user, multi-relay, multiple-input--multiple-output orthogonal frequency-division multiple-access (MIMO-OFDMA) cellular network based on joint transmit and receive beamforming. More specifically, the network's MIMO channels are mathematically decomposed into several effective multiple-input--single-output (MISO) channels, which are spatially multiplexed for transmission. For the sake of improving the attainable capacity, these MISO channels are grouped using a pair of novel grouping algorithms, which are then evaluated in terms of their per…
This letter investigates the artificial noise aided beamforming design for secure simultaneous wireless information and power transfer (SWIPT) in a two-tier downlink heterogeneous network, where one femtocell is overlaid with one macrocell in co-channel deployment. Each energy receiver (ER) in femtocell can be considered as a potential eaves- dropper for messages intended for information receiver (IR). Our objective is to maximize the secrecy rate at IR subject to the signal-to-interference-plus noise ratio (SINR) requirements of macro users (MUs), transmit power constraint and energy harvesti…
This paper considers the joint fronthaul compression and transmit beamforming design for the uplink cloud radio access network (C-RAN), in which multi-antenna user terminals communicate with a cloud-computing based centralized processor (CP) through multi-antenna base-stations (BSs) serving as relay nodes. A compress-and-forward relaying strategy, named the VMAC scheme, is employed, in which the BSs can either perform single-user compression or Wyner-Ziv coding to quantize the received signals and send the quantization bits to the CP via capacity-limited fronthaul links; the CP performs succes…
Multiple-input multiple-output (MIMO) millimeter wave (mmWave) systems are vulnerable to hardware impairments due to operating at high frequencies and employing a large number of radio- frequency (RF) hardware components. In particular, nonlinear power amplifiers (PAs) employed at the transmitter distort the signal when operated close to saturation due to energy efficiency considerations. In this paper, we study the performance of a MIMO mmWave hybrid beamforming scheme in the presence of nonlinear PAs. First, we develop a statistical model for the transmitted signal in such systems and show t…
The opportunistic beamforming in the downlink of multiple-input single-output (MISO) systems forms $N$ transmit beams, usually, no more than the number of transmit antennas $N_t$. However, the degrees of freedom in this downlink is as large as $N_t^2$. That is, at most $N_t^2$ rather than only $N_t$ users can be simultaneously transmitted and thus the scheduling latency can be significantly reduced. In this paper, we focus on the opportunistic beamforming schemes with $N_t<N\le N_t^2$ transmit beams in the downlink of MISO systems over Rayleigh fading channels. We first show how to design the …
This paper focuses on linear beamforming design and power allocation strategy for ergodic rate optimization in a two-user Multiple-Input-Single-Output (MISO) system with statistical and delayed channel state information at the transmitter (CSIT). We propose a transmission strategy, denoted as Statistical Alternative MAT (SAMAT), which exploits both channel statistics and delayed CSIT. Firstly, with statistical CSIT only, we focus on statistical beamforming (SBF) design that maximizes a lower bound on the ergodic sum-rate. Secondly, relying on both statistical and delayed CSIT, an iterative alg…
In this paper, we propose an adaptive coordinated Tx-Rx beamforming scheme for inter-user interference cancellation, when a base station (BS) communicates with multiple users that each has multiple receive antennas. The conventional coordinated Tx-Rx beamforming scheme transmits a fixed number of data streams for each user regardless of the instantaneous channel states, that is, all the users, no matter they are with ill-conditioned or well-conditioned channels, have the same number of data streams. However, in the proposed adaptive coordinated Tx-Rx beamforming scheme, we adaptively select th…
This paper investigates an intelligent reflecting surface (IRS)-aided multi-cell multiple-input single-output (MISO) system consisting of several multi-antenna base stations (BSs) each communicating with a single-antenna user, in which an IRS is dedicatedly deployed for assisting the wireless transmission and suppressing the inter-cell interference. Under this setup, we jointly optimize the coordinated transmit beamforming at the BSs and the reflective beamforming at the IRS, for the purpose of maximizing the minimum weighted received signal-to-interference-plus-noise ratio (SINR) at users, su…
Multiple-input multiple-output (MIMO) broadcast channels (BCs) (MIMO-BCs) with perfect channel state information (CSI) at the transmitter are considered. As joint user selection (US) and vector precoding (VP) (US-VP) with zero-forcing transmit beamforming (ZF-BF), US and continuous VP (CVP) (US-CVP) and data-dependent US (DD-US) are investigated. The replica method, developed in statistical physics, is used to analyze the energy penalties for the two US-VP schemes in the large-system limit, where the number of users, the number of selected users, and the number of transmit antennas tend to inf…
Massive multi-input multi-output (MIMO) uses a very large number of low-power transmit antennas to serve much smaller numbers of users. The most widely proposed type of massive MIMO transmit beamforming is zero-forcing, which is based on the right inverse of the overall MIMO channel matrix to force the inter-user interference to zero. The performance of massive MIMO is then analyzed based on the throughput of cell-edge users. This paper reassesses this beamforming philosophy, to instead consider the maximization of the energy efficiency of massive MIMO systems in assuring the quality-of- servi…
We consider settings in which T multi-antenna transmitters and K single-antenna receivers concurrently utilize the available communication resources. Each transmitter sends useful information only to its intended receivers and can degrade the performance of unintended systems. Here, we assume the performance measures associated with each receiver are monotonic with the received power gains. In general, the systems' joint operation is desired to be Pareto optimal. However, designing Pareto optimal resource allocation schemes is known to be difficult. In order to reduce the complexity of achievi…
Beamforming is indispensable in the operation of 60-GHz millimeter-wave directional multi-gigabit Wi-Fi. Simple power method and its extensions enable the transmitting and receiving antenna arrays to form a beam for single spatial stream. To further improve the spectral efficiency in future 60-GHz directional Wi-Fi, alternating least square (ALS) algorithm can form multiple beams between the transmitter and receiver for multi-input-multi-output (MIMO) operations. For both shared and split MIMO architecture, the ALS beamforming algorithm can be operated in both frequency-flat and frequency-sele…
For a multi-user interference channel with multi-antenna transmitters and single-antenna receivers, by restricting each transmitter to Gaussian input and each receiver to a single-user detector, computing the largest achievable rate region amounts to solving a family of non-convex optimization problems. Recognizing the intrinsic connection between the signal power at the intended receiver and the interference power at the unintended receiver, the original family of non-convex optimization problems is converted into a new family of convex optimization problems. It is shown that, for such interf…
A wireless network of multiple transmitter-user pairs overheard by an eavesdropper, where the transmitters are equipped with multiple antennas while the users and eavesdropper are equipped with a single antenna, is considered. At different levels of wireless channel knowledge, the problem of interest is beamforming to optimize the users' quality-of-service (QoS) in terms of their secrecy throughputs or maximize the network's energy efficiency under users' QoS. All these problems are seen as very difficult optimization problems with many nonconvex constraints and nonlinear equality constraints …
A Gaussian multiple-input multiple-output wiretap channel in which the eavesdropper and legitimate receiver are equipped with arbitrary numbers of antennas and the transmitter has two antennas is studied in this paper. Under an average power constraint, the optimal input covariance to obtain the secrecy capacity of this channel is unknown, in general. In this paper, the input covariance matrix required to achieve the capacity is determined. It is shown that the secrecy capacity of this channel can be achieved by linear precoding. The optimal precoding and power allocation schemes that maximize…
In this letter, we study a new technique for energy beamforming (EB) in multi-user networks, which combines large antenna retrodirectivity at the transmitter side with signal backscattering at the energy receivers. The proposed technique has low complexity and achieves EB without any active operation at the receivers or complicated signal processing techniques at the transmitter. Since the average harvested energy depends on the backscattering coefficients, we investigate different reflection policies for various design objectives. The proposed policies are analyzed from a system level standpo…
In this paper, we consider the problem of achieving max-min fairness amongst multiple co-channel multicast groups through transmit beamforming. We explicitly focus on overloaded scenarios in which the number of transmitting antennas is insufficient to neutralize all inter-group interference. Such scenarios are becoming increasingly relevant in the light of growing low-latency content delivery demands, and also commonly appear in multibeam satellite systems. We derive performance limits of classical beamforming strategies using DoF analysis unveiling their limitations; for example, rates satura…
Intelligent reflecting surface (IRS) has emerged as a cost-effective solution to enhance wireless communication performance via passive signal reflection. Existing works on IRS have mainly focused on investigating IRS's passive beamforming/reflection design to boost the communication rate for users assuming that their channel state information (CSI) is fully or partially known. However, how to exploit IRS to improve the wireless transmission reliability without any CSI, which is typical in high-mobility/delay-sensitive communication scenarios, remains largely open. In this paper, we study a ne…
This paper studies the coordinated beamforming design problem for the multiple-input single-output (MISO) interference channel, assuming only channel distribution information (CDI) at the transmitters. Under a given requirement on the rate outage probability for receivers, we aim to maximize the system utility (e.g., the weighted sum rate, weighted geometric mean rate, and the weighed harmonic mean rate) subject to the rate outage constraints and individual power constraints. The outage constraints, however, lead to a complicated, nonconvex structure for the considered beamforming design probl…
This paper studies an intelligent reflecting surface (IRS)-assisted multiuser multiple-input single-output (MISO) simultaneous wireless information and power transfer (SWIPT) system. In this system, a multi-antenna access point (AP) uses transmit beamforming to send both information and energy signals to a set of receivers each for information decoding (ID) or energy harvesting (EH), and a dedicatedly deployed IRS properly controls its reflecting phase shifts to form passive reflection beams for facilitating both ID and EH at receivers. Under this setup, we jointly optimize the (active) inform…
Reconfigurable intelligent surface (RIS) is a promising technique to enhance the performance of physical-layer key generation (PKG) due to its ability to smartly customize the radio environments. Existing RIS-assisted PKG methods are mainly based on the idealistic assumption of an independent and identically distributed (i.i.d.) channel model at both the transmitter and the RIS. However, the i.i.d. model is inaccurate for a typical RIS in an isotropic scattering environment. Also, neglecting the existence of channel spatial correlation would degrade the PKG performance. In this paper, we estab…
This paper studies the joint optimization problem of two-way relay beamforming, the receiver power splitting (PS) ratio as well as the transmit power at the sources to maximize the achievable sum-rate of a simultaneous wireless information and power transfer (SWIPT) system with a full-duplex (FD) multiple-input multiple-output (MIMO) amplify and forward (AF) relay, assuming perfect channel state information (CSI). In particular, our contribution is an iterative algorithm based on the difference of convex programming (DC) and one dimensional searching to achieve the joint solution. Simulation r…
This paper is on beamforming in wireless relay networks with perfect channel information at relays, the receiver, and the transmitter if there is a direct link between the transmitter and receiver. It is assumed that every node in the network has its own power constraint. A two-step amplify-and-forward protocol is used, in which the transmitter and relays not only use match filters to form a beam at the receiver but also adaptively adjust their transmit powers according to the channel strength information. For a network with any number of relays and no direct link, the optimal power control is…
Intelligent reflecting surface (IRS) is a promising solution to build a programmable wireless environment for future communication systems, in which the reflector elements steer the incident signal in fully customizable ways by passive beamforming. In this paper, an IRS-aided secure spatial modulation (SM) is proposed, where the IRS perform passive beamforming and information transfer simultaneously by adjusting the on-off states of the reflecting elements. We formulate an optimization problem to maximize the average secrecy rate (SR) by jointly optimizing the passive beamforming at IRS and th…
This paper considers a multiple-input multiple-output (MIMO) Gaussian wiretap channel model, where there exists a transmitter, a legitimate receiver and an eavesdropper, each equipped with multiple antennas. Perfect secrecy is achieved when the transmitter and the legitimate receiver can communicate at some positive rate, while ensuring that the eavesdropper gets zero bits of information. In this paper, the perfect secrecy capacity of the multiple antenna MIMO wiretap channel is found for aribtrary numbers of antennas under the assumption that the transmitter performs beamforming based on the …
This paper considers the multiple-input-single-output interference channel (MISO-IC) with interference decoding capability (IDC), so that the interference signal can be decoded and subtracted from the received signal. On the MISO-IC with single user decoding, transmit beamforming vectors are classically designed to reach a compromise between mitigating the generated interference (zero forcing of the interference) or maximizing the energy at the desired user. The particularly intriguing problem arising in the multi-antenna IC with IDC is that transmitters may now have the incentive to amplify t…
We derive the optimal signaling for a multiple input multiple output (MIMO) full-duplex two-way channel under the imperfect transmit front-end chain. We characterize the two-way rates of the channel by using a game-theoretical approach, where we focus on the Pareto boundary of the achievable rate region and Nash equilibia (NE). For a MISO full-duplex two-way channel, we prove that beamforming is an optimal transmission strategy which can achieve any point on the Pareto boundary. Furthermore, we present a closed-form expression for the optimal beamforming weights. In our numerical examples we q…
This paper examines linear beamforming methods for secure communications in a multiuser wiretap channel with a single transmitter, multiple legitimate receivers, and a single eavesdropper, where all nodes are equipped with multiple antennas. No information regarding the eavesdropper is presumed at the transmitter, and we examine both the broadcast MIMO downlink with independent information, and the multicast MIMO downlink with common information for all legitimate receivers. In both cases the information signal is transmitted with just enough power to guarantee a certain SINR at the desired re…
This paper considers the downlink of an ultra-reliable low-latency communication (URLLC) system in which a base station (BS) serves multiple single-antenna users in the short (finite) blocklength (FBL) regime with the assistance of a reconfigurable intelligent surface (RIS). In the FBL regime, the users' achievable rates are complex functions of the beamforming vectors and of the RIS's programmable reflecting elements (PREs). We propose the joint design of the transmit beamformers and PREs, the problem of maximizing the geometric mean (GM) of these rates (GM-rate) and show that this aforementi…
We derive optimal SNR-based transmit antenna selection rules at the source and relay for the nonregenerative half duplex MIMO relay channel. While antenna selection is a suboptimal form of beamforming, it has the advantage that the optimization is tractable and can be implemented with only a few bits of feedback from the destination to the source and relay. We compare the bit error rate of optimal antenna selection at both the source and relay to other proposed beamforming techniques and propose methods for performing the necessary limited feedback.
In this paper, we derive the optimal transmitter/ receiver beamforming vectors and relay weighting matrix for the multiple-input multiple-output amplify-and-forward relay channel. The analysis is accomplished in two steps. In the first step, the direct link between the transmitter (Tx) and receiver (Rx) is ignored and we show that the transmitter and the relay should map their signals to the strongest right singular vectors of the Tx-relay and relay-Rx channels. Based on the distributions of these vectors for independent identically distributed (i.i.d.) Rayleigh channels, the Grassmannian code…
Beamforming is a widely used method of provisioning high quality wireless channels that leads to high data rates and simple decoding structures. It requires feedback of Channel State Information (CSI) from receiver to transmitter, and the accuracy of this information is limited by rate constraints on the feedback channel and by delay. It is important to understand how the performance gains associated with beamforming depend on the accuracy or currency of the Channel State Information. This paper quantifies performance degradation caused by aging of CSI. It uses outage probability to measure th…
This paper studies a secrecy integrated sensing and communication (ISAC) system, in which a multi-antenna base station (BS) aims to send confidential messages to a single-antenna communication user (CU), and at the same time sense several targets that may be suspicious eavesdroppers. To ensure the sensing quality while preventing the eavesdropping, we consider that the BS sends dedicated sensing signals (in addition to confidential information signals) that play a dual role of artificial noise (AN) for confusing the eavesdropping targets. Under this setup, we jointly optimize the transmit info…
Magnetic induction (MI) based communication and power transfer systems have gained an increased attention in the recent years. Typical applications for these systems lie in the area of wireless charging, near-field communication, and wireless sensor networks. For an optimal system performance, the power efficiency needs to be maximized. Typically, this optimization refers to the impedance matching and tracking of the split-frequencies. However, an important role of magnitude and phase of the input signal has been mostly overlooked. Especially for the wireless power transfer systems with multip…
