arXivDaily arXiv每日学术速递 周一至周五更新
arXiv 1902.03009physics.med-ph
收藏

使用FSI模拟评估升主动脉瘤的峰值壁应力:主动脉刚度和外周阻力的影响

Evaluation of Peak Wall Stress in an Ascending Thoracic Aortic Aneurysm Using FSI Simulations: Effects of Aortic Stiffness and Peripheral Resistance

Rossella Campobasso, Francesca Condemi, Magalie Viallon, Pierre Croisille, Salvatore Campisi, Stéphane Avril

摘要:

目的.胸主动脉瘤(TAA)破裂或夹层常因高血压而发生,其表现为外周阻力突然增加,引起主动脉血容量的急性变化。有临床证据表明,顺应性更好的动脉瘤不太容易破裂,因为它们可以承受这种体积变化。本文的目的是通过计算评估外周阻力变化所起的作用以及主动脉僵硬度对升主动脉瓣峰值壁应力的影响来验证这一范例。方法.使用患者特定的几何形状和边界条件进行流体-结构相互作用(FSI)分析,这些几何形状和边界条件来自于在患者身上采集的4D MRI数据集。假设血液不可压缩,并使用Carreau模型将其作为非牛顿流体处理,同时从手术修复后在体外进行的膨胀膨胀试验中获得壁的机械性能。在ANSYS Fluent中求解纳维-斯托克斯方程。任意拉格朗日欧拉公式被用来考虑壁变形。在固体域和流体域的交界面处,流体压力传递给壁面,壁面位移传递给流体。这两个系统通过系统耦合组件连接,该组件控制ANSYS中流体和固体模拟的求解器执行。从流体模拟开始依次求解流体和固体域。结果利用流固耦合分析方法,研究了升主动脉血流、壁面切应力和壁面应力的分布。我们总是观察到一个显着的流动偏心率在模拟中,在非常好的协议与使用4D MRI测量的速度分布。结果还显示,由于外周阻力和主动脉刚度的增加,壁应力峰值显著增加。在最坏的情况下,最大的周边阻力(10 - 10千克·秒·米-4)和刚度(10兆帕)导致的最大主应力等于702千帕,而它在正常条件下只有77千帕。结论.这是首次在高血压和主动脉僵硬度增加的联合作用下量化aTAA破裂的风险。我们的研究结果表明,较硬的TAA可能具有最大的壁应力分布变化,外周血管阻力的急性变化可能显著增加较硬动脉瘤的破裂风险。

英文摘要:

Purpose. It has been reported clinically that rupture or dissections in thoracic aortic aneurysms (TAA) often occur due to hypertension which may be modelled with sudden increase of peripheral resistance, inducing acute changes of blood volumes in the aorta. There is clinical evidence that more compliant aneurysms are less prone to rupture as they can sustain such changes of volume. The aim of the current paper is to verify this paradigm by evaluating computationally the role played by the variation of peripheral resistance and the impact of aortic stiffness onto peak wall stress in ascending TAA. Methods. Fluid-Structure Interaction (FSI) analyses were performed using patient-specific geometries and boundary conditions derived from 4D MRI datasets acquired on a patient. Blood was assumed incompressible and was treated as a non-Newtonian fluid using the Carreau model while the wall mechanical properties were obtained from the bulge inflation tests carried out in vitro after surgical repair. The Navier Stokes equations were solved in ANSYS Fluent. The Arbitrary Lagrangian Eulerian formulation was used to account for the wall deformations. At the interface between the solid domain and the fluid domain, the fluid pressure was transferred to the wall and the displacement of the wall was transferred to the fluid. The two systems were connected by the System Coupling component which controls the solver execution of fluid and solid simulations in ANSYS. Fluid and solid domains were solved sequentially starting from the fluid simulations. Results. Distributions of blood flow, wall shear stress and wall stress were evaluated in the ascending thoracic aorta using the FSI analyses. We always observed a significant flow eccentricity in the simulations, in very good agreement with velocity profiles measured using 4D MRI. The results also showed significant increase of peak wall stress due to the increase of peripheral resistance and aortic stiffness. In the worst case scenario, the largest peripheral resistance (10 10 kg.s.m-4) and stiffness (10 MPa) resulted in a maximal principal stress equal to 702 kPa, whereas it was only 77 kPa in normal conditions. Conclusions. This is the first time that the risk of rupture of an aTAA is quantified in case of the combined effects of hypertension and aortic stiffness increase. Our findings suggest that a stiffer TAA may have the most altered distribution of wall stress and an acute change of peripheral vascular resistance could significantly increase the risk of rupture for a stiffer aneurysm.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑