High-performance graphene field-effect transistors have been fabricated on epitaxial graphene synthesized on a two-inch SiC wafer, achieving a cutoff frequency of 100 GHz for a gate length of 240 nm. The high-frequency performance of these epitaxial graphene transistors not only shows the highest speed for any graphene devices up to date, but it also exceeds that of Si MOSFETs at the same gate length. The result confirms the high potential of graphene for advanced electronics applications, marking an important milestone for carbon electronics.
Single layer hexagonal boron nitride is produced on 2 inch Pt(111)/sapphire wafers. The growth with borazine vapour deposition at process temperatures between 1000 and 1300 K is in-situ investigated by photoelectron yield measurements. The growth kinetics is slower at higher temperatures and follows a tanh$^2$ law which better fits for higher temperatures. The crystal-quality of h-BN/Pt(111) is inferred from scanning low energy electron diffraction (x-y LEED). The data indicate a strong dependence of the epitaxy on the growth temperature. The dominant structure is an aligned coincidence lattic…
The development of graphene electronics requires the integration of graphene devices with Si-CMOS technology. Most strategies involve the transfer of graphene sheets onto silicon, with the inherent difficulties of clean transfer and subsequent graphene nano-patterning that degrades considerably the electronic mobility of nanopatterned graphene. Epitaxial graphene (EG) by contrast is grown on an essentially perfect crystalline (semi-insulating) surface, and graphene nanostructures with exceptional properties have been realized by a selective growth process on tailored SiC surface that requires …
The formation of graphene on any desirable substrate is extremely essential for the successful replacement of Si with graphene in all technological applications in the beyond-CMOS era. Recently, we observed that a Ti layer formed on epitaxial graphene by electron-beam evaporation has the sufficiently large area of contact with the surface of epitaxial graphene for the exfoliation process to take place. We also observed that the exfoliated FLG on the Ti layer can be easily transferred onto a SiO2/Si substrate. In this paper, we have proposed a new technique for transferring graphene having a la…
Graphene nanoribbon (GNR) field-effect transistors (FETs) with widths down to 12 nm have been fabricated by electron beam lithography using a wafer-scale chemical vapor deposition (CVD) process to form the graphene. The GNR FETs show drain-current modulation of approximately 10 at 300 K, increasing to nearly 106 at 4 K. The strong temperature dependence of the minimum current indicates the opening of a bandgap for CVD-grown GNR-FETs. The extracted bandgap is estimated to be around 0.1 eV by differential conductance methods. This work highlights the development of CVD-grown large-area graphene …
Up to two layers of epitaxial graphene have been grown on the Si-face of two-inch SiC wafers exhibiting room-temperature Hall mobilities up to 1800 cm^2/Vs, measured from ungated, large, 160 micron x 200 micron Hall bars, and up to 4000 cm^2/Vs, from top-gated, small, 1 micron x 1.5 micron Hall bars. The growth process involved a combination of a cleaning step of the SiC in a Si-containing gas, followed by an annealing step in Argon for epitaxial graphene formation. The structure and morphology of this graphene has been characterized using AFM, HRTEM, and Raman spectroscopy. Furthermore, top-g…
We report a direct correlation between carrier mobility and Raman topography of epitaxial graphene (EG) grown on silicon carbide (SiC). We show the Hall mobility of material on the Si-face of SiC [SiC(0001)] is not only highly dependent on thickness uniformity but also on monolayer strain uniformity. Only when both thickness and strain are uniform over a significant fraction (> 40%) of the device active area does the mobility exceed 1000 cm2/V-s. Additionally, we achieve high mobility epitaxial graphene (18,100 cm2/V-s at room temperature) on the C-face of SiC [SiC(000-1)] and show that carrie…
Three types of first generation epitaxial graphene field effect transistors (FET) are presented and their relative merits are discussed. Graphene is epitaxially grown on both the carbon and silicon faces of hexagonal silicon carbide and patterned with electron beam lithography. The channels have a Hall bar geometry to facilitate magnetoresistance measurements. FETs patterned on the Si-face exhibit off-to-on channel resistance ratios that exceed 30. C-face FETs have lower off-to-on resistance ratios, but their mobilities (up to 5000 cm2/Vs) are much larger than that for Si-face transistors. Ini…
Realization of wafer-scale single-crystal films of transition metal dichalcogenides (TMDs) such as tungsten sulfide requires epitaxial growth and coalescence of oriented domains to form a continuous monolayer. The domains must be oriented in the same crystallographic direction on the substrate to avoid the formation of metallic inversion domain boundaries (IDBs) which are a common feature of layered chalcogenides. Here we demonstrate fully-coalesced single orientation tungsten sulfide monolayers on 2-inch diameter c-plane sapphire by metalorganic chemical vapor deposition using a multi-step gr…
Epitaxial Al/GaAs/Al structures having controlled thickness of high-quality GaAs and pristine interfaces have been fabricated using a wafer-bonding technique. III-V semiconductor/Al structures are grown by molecular beam epitaxy on III-V semiconductor substrates and bonded to silicon and sapphire. Selective etching is used to remove the III-V substrate followed by surface cleaning and superconductor regrowth, resulting in epitaxial Al/GaAs/Al tri-layers on sapphire or silicon substrates. Structures are characterized with reflection high energy electron diffraction, atomic force microscopy, X-r…
An in vacuo thermal desorption process has been accomplished to form epitaxial graphene (EG) on 4H- and 6H-SiC substrates using a commercial chemical vapor deposition reactor. Correlation of growth conditions and the morphology and electrical properties of EG are described. Raman spectra of EG on Si-face samples were dominated by monolayer thickness. This approach was used to grow EG on 50 mm SiC wafers that were subsequently fabricated into field effect transistors with fmax of 14 GHz.
Graphene field-effect transistors are integrated with solution-processed multilayer hybrid organic-inorganic self-assembled nanodielectrics (SANDs). The resulting devices exhibit low-operating voltage (2 V), negligible hysteresis, current saturation with intrinsic gain > 1.0 in vacuum (pressure < 2 x 10-5 Torr), and overall improved performance compared to control devices on conventional SiO2 gate dielectrics. Statistical analysis of the field-effect mobility and residual carrier concentration demonstrate high spatial uniformity of the dielectric interfacial properties and graphene transistor …
We developed means to produce wafer scale, high-quality graphene films as large as 3 inch wafer size on Ni and Cu films under ambient-pressure and transfer them onto arbitrary substrates through instantaneous etching of metal layers. We also demonstrated the applications of the large-area graphene films for the batch fabrication of field-effect transistor (FET) arrays and stretchable strain gauges showing extraordinary performances. Transistors showed the hole and electron mobilities of the device of 1,100 cm2/Vs and 550 cm2/Vs at drain bias of -0.75V, respectively. The piezo-resistance gauge …
The Diels-Alder surface modified top epitaxial graphene layer, with newly created pair of sp3 carbon centres, results in abrupt minimization of interlayer van der Waals interactions between two stacked graphene planes, and escapes the wafer during post-reaction manipulation stage, leaving the layer under it almost pristine-like. Above picture shows Diels-Alder functionalized sp2/sp3 graphene adduct leaves the parent wafer. In this communication we systematically address several fundamental questions in graphene surface chemistry, which are of extreme importance for device fabrication, and in s…
Homogeneous highly epitaxial LaSrMnO3 (LSMO) thin films have been grown on Yttria-stabilized-Zirconia (YsZ) / CeO2 buffer layers on technological relevant 4" silicon wafers using a Twente Solid State Technology B.V. (TSST) developed large area Pulsed Laser Deposition (PLD) setup. We study and show the results of the effect of an additional SrRuO3 buffer layer on the growth temperature dependent structural and magnetic properties of LSMO films. With the introduction of a thin SrRuO3 layer on top of the buffer stack, LSMO films show ferromagnetic behaviour for growth temperatures as low as 250C.…
This paper describes the behavior of top gated transistors fabricated using carbon, particularly epitaxial graphene on SiC, as the active material. In the past decade research has identified carbon-based electronics as a possible alternative to silicon-based electronics. This enthusiasm was spurred by high carbon nanotube carrier mobilities. However, nanotube production, placement, and control are all serious issues. Graphene, a thin sheet of graphitic carbon, can overcome some of these problems and therefore is a promising new electronic material. Although graphene devices have been built bef…
The maximum oscillation frequency (fmax) quantifies the practical upper bound for useful circuit operation. We report here an fmax of 70 GHz in transistors using epitaxial graphene grown on the C-face of SiC. This is a significant improvement over Si-face epitaxial graphene used in the prior high frequency transistor studies, exemplifying the superior electronics potential of C-face epitaxial graphene. Careful transistor design using a high κ dielectric T-gate and self-aligned contacts, further contributed to the record-breaking fmax.
We report herein fabrication and characterization of a thin-film transistor (TFT) using single-crystalline, epitaxial SrTiO3 film, which was grown by a pulsed laser deposition technique followed by the thermal annealing treatment in an oxygen atmosphere. Although TFTs on the polycrystalline epitaxial SrTiO3 films (as-deposited) exhibited poor transistor characteristics, the annealed single-crystalline SrTiO3 TFT exhibits transistor characteristics comparable with those of bulk single-crystal SrTiO3 FET: an on/off current ratio >10^5, sub-threshold swing ~2.1 V/decade, and field-effect mobility…
Transition metal dichalcogenide (TMD) monolayers and heterostructures have emerged as a compelling class of materials with transformative new science that may be harnessed for novel device technologies. These materials are commonly fabricated by exfoliation of flakes from bulk crystals, but wafer-scale epitaxy of single crystal films is required to advance the field. This article reviews the fundamental aspects of epitaxial growth of van der Waals bonded crystals specific to TMD films. The structural and electronic properties of TMD crystals are initially described along with sources and metho…
We demonstrate that the confocal laser scanning microscopy (CLSM) provides a non-destructive, highly-efficient characterization method for large-area epitaxial graphene and graphene nanostructures on SiC substrates, which can be applied in ambient air without sample preparation and is insusceptible to surface charging or surface contamination. Based on the variation of reflected intensity from regions covered by interfacial layer, single layer, bilayer, or few layer graphene, and through the correlation to the results from Raman spectroscopy and SPM, CLSM images with a high resolution (around …
Transition metal dichalcogenides (TMDs) are materials that can exhibit intriguing optical properties like a change of the bandgap from indirect to direct when being thinned down to a monolayer. Well-resolved narrow excitonic resonances can be observed for such monolayers, however only for materials of sufficient crystalline quality, so far mostly available in the form of micrometer-sized flakes. A further significant improvement of optical and electrical properties can be achieved by transferring the TMD on hexagonal boron nitride (hBN). To exploit the full potential of TMDs in future applicat…
Freestanding single-crystalline membranes are an important building block for functional electronics. Especially, compounds semiconductor membranes such as III-N and III-V offer great opportunities for optoelectronics, high-power electronics, and high-speed computing. Despite huge efforts to produce such membranes by detaching epitaxial layers from donor wafers, however, it is still challenging to harvest epitaxial layers using practical processes. Here, we demonstrate a method to grow and harvest multiple epitaxial membranes with extremely high throughput at the wafer scale. For this, 2D mate…
We report the first observation of ferroelectric gating in AlScN barrier wide-bandgap nitride transistors. These FerroHEMT devices realized by direct epitaxial growth represent a new class of ferroelectric transistors in which the semiconductor is itself polar, and the crystalline ferroelectric barrier is lattice-matched to the substrate. The FerroHEMTs reported here use the thinnest nitride high K and ferroelectric barriers to date to deliver the highest on currents at 4 A/mm, and highest speed AlScN transistors with fmax larger than 150 GHz observed in any ferroelectric transistor. The Ferro…
Two-dimensional (2D) materials have attracted substantial attention in electronic and optoelectronic applications with superior advantages of being flexible, transparent and highly tunable. Gapless graphene exhibits ultra-broadband and fast photoresponse while the 2D semiconducting MoS2 and GaTe unveil high sensitivity and tunable responsivity to visible light. However, the device yield and the repeatability call for a further improvement of the 2D materials to render large-scale uniformity. Here we report a layer-by-layer growth of wafer-scale GaTe with a hole mobility of 28.4 cm2/Vs by molec…
Precise control of the properties of semiconductor quantum dots (QDs) is vital for creating novel devices for quantum photonics and advanced opto-electronics. Suitable low QD-density for single QD devices and experiments are challenging to control during epitaxy and are typically found only in limited regions of the wafer. Here, we demonstrate how conventional molecular beam epitaxy (MBE) can be used to modulate the density of optically active QDs in one- and two- dimensional patterns, while still retaining excellent quality. We find that material thickness gradients during layer-by-layer grow…
We present a new fabrication method for epitaxial graphene on SiC which enables the growth of ultra-smooth defect- and bilayer-free graphene sheets with an unprecedented reproducibility, a necessary prerequisite for wafer-scale fabrication of high quality graphene-based electronic devices. The inherent but unfavorable formation of high SiC surface terrace steps during high temperature sublimation growth is suppressed by rapid formation of the graphene buffer layer which stabilizes the SiC surface. The enhanced nucleation is enforced by decomposition of polymer adsorbates which act as a carbon …
Wafer-scale Demonstration of High-voltage beta-Ga2O3 MOSFETs with Excellent Uniformity and over 3kV Breakdown Voltages
Yongjiang Laboratory（甬江实验室）；Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences（中国科学院宁波材料技术与工程研究所）；School of Microelectronics, Fudan University（复旦大学微电子学院）；Hangzhou Garen Semiconductor Co., Ltd.（杭州嘉然半导体有限公司）
Radiative efficiency of highly luminescent bulk InP wafers severely degrades upon heat treatment involved in epitaxial growth of quaternary layers and fabrication of photodiodes on the surface. This unfortunate property impedes the use of bulk InP as scintillator material. On the other hand, it is known that thin epitaxial InP layers, grown by molecular beam epitaxy (MBE) or metal-organic chemical vapor deposition (MOCVD), do not exhibit any degradation. These layers, however, are too thin to be useful in scintillators. The capability of hydride vapor phase epitaxy (HVPE) process to grow thick…
We demonstrate non-volatile, n-type, back-gated, MoS$_{2}$ transistors, placed directly on an epitaxial grown, single crystalline, PbZr$_{0.2}$Ti$_{0.8}$O$_{3}$ (PZT) ferroelectric. The transistors show decent ON current (19 $μA/μ$m), high on-off ratio (10$^{7}$), and a subthreshold swing of (SS ~ 92 mV/dec) with a 100 nm thick PZT layer as the back gate oxide. Importantly, the ferroelectric polarization can directly control the channel charge, showing a clear anti-clockwise hysteresis. We have selfconsistently confirmed the switching of the ferroelectric and corresponding change in channel cu…
We have investigated epitaxial graphene films grown on SiC(0001) by annealing in an atmosphere of Ar instead of vacuum. Using AFM and LEEM we observe a significantly improved surface morphology and graphene domain size. Hall measurements on monolayer graphene films show a carrier mobility of around 1000 cm^2/Vs at room temperature and 2000 cm^2/Vs at 27K. The growth process introduced here establishes the synthesis of graphene films on a technologically viable basis.
The materials science of graphene grown epitaxially on the hexagonal basal planes of SiC crystals is reviewed. We show that the growth of epitaxial graphene on Si-terminated SiC(0001) is much different than growth on the C-terminated SiC(000 -1) surface, and discuss the physical structure of these graphenes. The unique electronic structure and transport properties of each type of epitaxial graphene is described, as well as progress toward the development of epitaxial graphene devices. This materials system is rich in subtleties, and graphene grown on the two polar faces differs in important wa…
Uniform single layer graphene was grown on single-crystal Ir films a few nanometers thick which were prepared by pulsed laser deposition on sapphire wafers. These graphene layers have a single crystallographic orientation and a very low density of defects, as shown by diffraction, scanning tunnelling microscopy, and Raman spectroscopy. Their structural quality is as high as that of graphene produced on Ir bulk single crystals, i.e. much higher than on metal thin films used so far.
We introduce a deep-recessed gate architecture in $β$-Ga$_2$O$_3$ delta-doped field effect transistors for improvement in DC-RF dispersion and breakdown properties. The device design incorporates an unintentionally doped $β$-Ga$_2$O$_3$ layer as the passivation dielectric. To fabricate the device, the deep-recess geometry was developed using BCl$_3$ plasma based etching at ~5 W RIE to ensure minimal plasma damage. Etch damage incurred with plasma etching was mitigated by annealing in vacuum at temperatures above 600 $°$C. A gate-connected field-plate edge termination was implemented for effici…
We report on spectroscopy results from the mid- to far-infrared on wafer-scale graphene, grown either epitaxially on silicon carbide, or by chemical vapor deposition. The free carrier absorption (Drude peak) is simultaneously obtained with the universal optical conductivity (due to interband transitions), and the wavelength at which Pauli blocking occurs due to band filling. From these the graphene layer number, doping level, sheet resistivity, carrier mobility, and scattering rate can be inferred. The mid-IR absorption of epitaxial two-layer graphene shows a less pronounced peak at 0.37\pm0.0…
We use ultra-high vacuum chemical vapor deposition to grow polycrystalline silicon carbide (SiC) on c-plane sapphire wafers which are then annealed between 1250 and 1450°C in vacuum to create epitaxial multilayer graphene (MLG). Despite the surface roughness and small domain size of the polycrystalline SiC, a conformal MLG film is formed. By planarizing the SiC prior to graphene growth, a reduction of the Raman defect band is observed in the final MLG. The graphene formed on polished SiC films also demonstrates significantly more ordered layer-by-layer growth and increased carrier mobility for…
A fresh look on carbon-based transistor channel materials like single-walled carbon nanotubes (CNT) and graphene nanoribbons (GNR) in future electronic applications is given. Although theoretical predictions initially promised that GNR (which do have a bandgap) would perform equally well as transistors based on CNTs, experimental evidence for the well-behaved transistor action is missing up to now. Possible reasons for the shortcomings as well as possible solutions to overcome the performance gap will be addressed. In contrast to GNR, short channel CNT field effect transistors (FET) demonstrat…
We present a technique to tune the charge density of epitaxial graphene via an electrostatic gate that is buried in the silicon carbide substrate. The result is a device in which graphene remains accessible for further manipulation or investigation. Via nitrogen or phosphor implantation into a silicon carbide wafer and subsequent graphene growth, devices can routinely be fabricated using standard semiconductor technology. We have optimized samples for room temperature as well as for cryogenic temperature operation. Depending on implantation dose and temperature we operate in two gating regimes…
We experimentally demonstrate DC functionality of graphene-based hot electron transistors, which we call Graphene Base Transistors (GBT). The fabrication scheme is potentially compatible with silicon technology and can be carried out at the wafer scale with standard silicon technology. The state of the GBTs can be switched by a potential applied to the transistor base, which is made of graphene. Transfer characteristics of the GBTs show ON/OFF current ratios exceeding 50.000.
Atomically thin MoS2/graphene heterostructures are promising candidates for nanoelectronic and optoelectronic technologies. Among different graphene substrates, epitaxial graphene (EG) on SiC provides several potential advantages for such heterostructures including high electronic quality, tunable substrate coupling, wafer-scale processability, and crystalline ordering that can template commensurate growth. Exploiting these attributes, we demonstrate here the thickness-controlled van der Waals epitaxial growth of MoS2 on EG via chemical vapor deposition, giving rise to transfer-free synthesis …
Two-dimensional (2D) semiconductor of MoS2 has great potential for advanced electronics technologies beyond silicon1-9. So far, high-quality monolayer MoS2 wafers10-12 are already available and various demonstrations from individual transistors to integrated circuits have also been shown13-15. In addition to the monolayer, multilayers have narrower band gaps but improved carrier mobilities and current capacities over the monolayer5,16-18. However, achieving high-quality multilayer MoS2 wafers remains a challenge. Here we report the growth of high quality multilayer MoS2 4-inch wafers via the l…
We demonstrate high-quality epitaxial germanium (Ge) films on a metallic silicide, Fe3Si, grown directly on a Ge(111) substrate. Using molecular beam epitaxy techniques, we can obtain an artificially controlled arrangement of silicon (Si) or iron (Fe) atoms at the surface on Fe3Si(111). The Si-terminated Fe3Si(111) surface enables us to grow two-dimensional epitaxial Ge films, whereas the Fe-terminated one causes the three-dimensional epitaxial growth of Ge films. The high-quality Ge grown on the Si-terminated surface has almost no strain, meaning that the Ge films are not grown on the low-tem…
We report the use of a surfactant molecule during the epitaxy of graphene on SiC(0001) that leads to the growth in an unconventional orientation, namely $R0^\circ$ rotation with respect to the SiC lattice. It yields a very high-quality single-layer graphene with a uniform orientation with respect to the substrate, on the wafer scale. We find an increased quality and homogeneity compared to the approach based on the use of a pre-oriented template to induce the unconventional orientation. Using spot profile analysis low energy electron diffraction, angle-resolved photoelectron spectroscopy, and …
Epitaxial growth and controllable doping of wafer-scale single-crystal transition-metal dichalcogenides (TMDCs) are two central tasks for extending Moore's law beyond silicon. However, despite considerable efforts, addressing such crucial issues simultaneously under two-dimensional (2D) confinement is yet to be realized. Here we design an ingenious epitaxial strategy to synthesize record-breaking 4-inch single-crystal Fe-doped TMDCs monolayers on industry-compatible c-plane sapphire without miscut angle. In-depth characterizations and theoretical calculations reveal that the introduction of Fe…
In this work, we report on the electronic properties of solution-gated field effect transistors (SGFETs) fabricated using large-area graphene. Devices prepared both with epitaxially grown graphene on SiC as well as with chemical vapor deposition grown graphene on Cu exhibit high transconductances, which are a consequence of the high mobility of charge carriers in graphene and the large capacitance at the graphene/water interface. The performance of graphene SGFETs, in terms of gate sensitivity, is compared to other SGFET technologies and found to be clearly superior, confirming the potential o…
Using ultrafast optical pump-probe spectroscopy, we have measured carrier relaxation times in epitaxial graphene layers grown on SiC wafers. We find two distinct time scales associated with the relaxation of nonequilibrium photogenerated carriers. An initial fast relaxation transient in the 70-120 fs range is followed by a slower relaxation process in the 0.4-1.7 ps range. The slower relaxation time is found to be inversely proportional to the degree of crystalline disorder in the graphene layers as measured by Raman spectroscopy. We relate the measured fast and slow time constants to carrier-…
Growth of epitaxial graphene on the C-face of SiC has been investigated. Using a confinement controlled sublimation (CCS) method, we have achieved well controlled growth and been able to observe propagation of uniform monolayer graphene. Surface patterns uncover two important aspects of the growth, i.e. carbon diffusion and stoichiometric requirement. Moreover, a new "stepdown" growth mode has been discovered. Via this mode, monolayer graphene domains can have an area of hundreds of square micrometers, while, most importantly, step bunching is avoided and the initial uniformly stepped SiC surf…
In this paper we present an improved process for producing elastomer transistor stamps and high-mobility organic field-effect transistors (FETs) based on semiconducting acene molecular crystals. In particular, we have removed the need to use a silanized Si wafer for curing the stamps and to handle a fragile micron-thickness polydimethylsiloxane (PDMS) insulating film and laminate it, bubble free, against the PDMS transistor stamp. We find that despite the altered design, rougher PDMS surface, and lamination and measurement of the device in air, we still achieve electrical mobilities of order 1…
Methylammonium lead iodide perovskite has attracted intensive interest for its diverse optoelectronic applications. However, most studies to date have been limited to bulk thin films that are difficult to implement for integrated device arrays because of their incompatibility with typical lithography processes. We report the first patterned growth of regular arrays of perovskite microplate crystals for functional electronics and optoelectronics. We show that large arrays of lead iodide microplates can be grown from an aqueous solution through a seeded growth process and can be further intercal…
Ultra-thin MoS2 has recently emerged as a promising two-dimensional semiconductor for electronic and optoelectronic applications. Here, we report high mobility (>60 cm2/Vs at room temperature) field-effect transistors that employ unencapsulated single-layer MoS2 on oxidized Si wafers with a low level of extrinsic contamination. While charge transport in the sub-threshold regime is consistent with a variable range hopping model, monotonically decreasing field-effect mobility with increasing temperature suggests band-like transport in the linear regime. At temperatures below 100 K, temperature-i…
Monolayer graphene has been grown on crystallized Cu (111) films on standard oxidized Si 100 mm wafers. The monolayer graphene demonstrates high uniformity (>97% coverage), with immeasurable defects (>95% defect-negligible) across the entire wafer. Key to these results is the phase transition of evaporated copper films from amorphous to crystalline at the growth temperature as corroborated by X-ray diffraction and electron backscatter diffraction. Noticeably, phase transition of copper film is observed on technologically ubiquitous oxidized Si wafer where the oxide is a standard amorphous ther…
The discovery of electric field induced bandgap opening in bilayer graphene opens new door for making semiconducting graphene without aggressive size scaling or using expensive substrates. However, bilayer graphene samples have been limited to um size scale thus far, and synthesis of wafer scale bilayer graphene posts tremendous challenge. Here we report homogeneous bilayer graphene films over at least 2 inch x 2 inch area, synthesized by chemical vapor deposition on copper foil and subsequently transferred to arbitrary substrates. The bilayer nature of graphene film is verified by Raman spect…
We report the growth of high-quality triangular GaN nanomesas, 30-nm thick, on the C-face of 4H-SiC using nano selective area growth (NSAG) with patterned epitaxial graphene grown on SiC as an embedded mask. NSAG alleviates the problems of defective crystals in the heteroepitaxial growth of nitrides, and the high mobility graphene film can readily provide the back low-dissipative electrode in GaN-based optoelectronic devices. The process consists in first growing a 5-8 graphene layers film on the C-face of 4H- SiC by confinement-controlled sublimation of silicon carbide. The graphene film is t…
