Interfacial charge transfer plays an essential role in establishing the relative alignment of the metal Fermi level and the energy bands of organic semiconductors. While the details remain elusive in many systems, this charge transfer has been inferred in a number of photoemission experiments. We present electronic transport measurements in very short channel ($L < 100$ nm) transistors made from poly(3-hexylthiophene) (P3HT). As channel length is reduced, the evolution of the contact resistance and the zero-gate-voltage conductance are consistent with such charge transfer. Short channel conduction in devices with Pt contacts is greatly enhanced compared to analogous devices with Au contacts, consistent with charge transfer expectations. Alternating current scanning tunneling microscopy (ACSTM) provides further evidence that holes are transferred from Pt into P3HT, while much less charge transfer takes place at the Au/P3HT interface.
We show that the performance of pentacene transistors can be significantly improved by maximizing the interfacial area at single walled carbon nanotube (SWCNT)/pentacene. The interfacial areas are varied by anchoring short SWCNTs of different densities (0-30/μm) to the Pd electrodes. The average mobility is increased three, six and nine times for low, medium and high SWCNT densities, respectively, compared to the devices with zero SWCNT. The current on-off ratio and on-current are increased up to 40 times and 20 times with increasing the SWCNT density. We explain the improved device performanc…
We report a strategy to design nanoscale cold-source field-effect transistors (CS-FETs) with bias-independent sub-60 mV/dec subthreshold swing (SS). By first-principles calculations and quantum-transport simulations, we reveal that the energy alignment of density of states (DOS) between the drain and source electrodes is critical to achieving bias-independent SS. By defining "gate window", we propose a device model to demonstrate how similar slopes of the drain DOS falling into the gate window can stabilize the SS under different bias. This study underscores the significance of drain DOS engin…
Realization of high-quality van der Waals (vdW) heterostructures with tailored properties by stacking two-dimensional (2D) layers requires atomically clean interfaces. Because of strong adhesion between the constituent layers, the vdW forces could drive trapped contaminants together into submicron-size bubbles, which leaves large interfacial areas atomically clean. Such a phenomenon is dubbed self-cleaning mechanism in 2D systems. Here, we demonstrate the breakdown of self-cleaning mechanism for nanoscale interfacial bubbles in tiny-angle twisted bilayer graphene (TBG). In the tiny-angle TBG, …
Two-dimensional semiconductors are structurally ideal channel materials for the ultimate atomic electronics after silicon era. A long-standing puzzle is the low carrier mobility (μ) in them as compared with corresponding bulk structures, which constitutes the main hurdle for realizing high-performance devices. To address this issue, we perform combined experimental and theoretical study on atomically thin MoS2 field effect transistors with varying the number of MoS2 layers (NLs). Experimentally, an intimate relation is observed with a 10-fold degradation in μ for extremely thinned monolayer ch…
We theoretically demonstrate that a dipole layer on the electrode can modulate the transmission properties of nanoscale devices by influencing the contact properties, through first principles simulations on carbon nanotube based field effect transistors. The dipole layer is realized by potassium adsorption on Au electrodes, which shifts the electrostatic potential at the near contact region significantly. The dipoles parallel to the direction of the bias voltage may act as a supplement to the effect of gate voltages, while the perpendicular dipoles may modify the interface barrier of the conta…
We introduce a methodology for density-based topology optimization of non-Fourier thermal transport in nanostructures, based upon adjoint-based sensitivity analysis of the phonon Boltzmann transport equation (BTE) and a novel material interpolation technique, the "transmission interpolation model" (TIM). The key challenge in BTE optimization is handling the interplay between real- and momentum-resolved material properties. By parameterizing the material density with an interfacial transmission coefficient, TIM is able to recover the hard-wall and no-interface limits, while guaranteeing a smoot…
We report the observation of channel-width dependent enhancement in nanoscale field effect transistors containing lithographically-patterned silicon nanowires as the conduction channel. These devices behave as conventional metal-oxide-semiconductor field-effect transistors in reverse source drain bias. Reduction of nanowire width below 200 nm leads to dramatic change in the threshold voltage. Due to increased surface-to-volume ratio, these devices show higher transconductance per unit width at smaller width. Our devices with nanoscale channel width demonstrate extreme sensitivity to surface fi…
p-type doping from the dielectric/semiconductor interface of a SnO2 thin film transistor (TFT) has been utilized to develop high carrier mobility balanced ambipolar oxide-transistor. To introduce this interfacial-doping, bottom-gate top-contact TFTs have been fabricated by using two different ion-conducting oxide dielectrics which contain trivalent atoms. These ion-conducting dielectrics are LilnO2 and LiGaO2 respectively, containing mobile Li+ ion. During SnO2 thin film fabrication on top of the ionic dielectric, those trivalent atoms allow p- doping to the interfacial SnO2 layer to introduce…
We demonstrate single dopant implantation into the channel of a silicon nanoscale metal-oxide-semiconductor field-effect-transistor. This is achieved by monitoring the drain current modulation during ion irradiation. Deterministic doping is crucial for overcoming dopant number variability in present nanoscale devices and for exploiting single atom degrees of freedom. The two main ion stopping processes that induce drain current modulation are examined. We employ 500~keV He ions, in which electronic stopping is dominant, leading to discrete increases in drain current and 14~keV P dopants for wh…
Understanding energy dissipation and transport in nanoscale structures is of great importance for the design of energy-efficient circuits and energy-conversion systems. This is also a rich domain for fundamental discoveries at the intersection of electron, lattice (phonon), and optical (photon) interactions. This review presents recent progress in understanding and manipulation of energy dissipation and transport in nanoscale solid-state structures. First, the landscape of power usage from nanoscale transistors (~10^-8 W) to massive data centers (~10^9 W) is surveyed. Then, focus is given to e…
Magnon transistors that can effectively regulate magnon transport by an electric field are desired for magnonics which aims to provide a Joule-heating free alternative to the conventional electronics owing to the electric neutrality of magnons (the key carriers of spin-angular momenta in the magnonics). However, also due to their electric neutrality, magnons have no access to directly interact with an electric field and it is thus difficult to manipulate magnon transport by voltages straightforwardly. Here, we demonstrated a gate voltage ($V_{\rm g}$) applied on a nonmagnetic metal/magnetic in…
A first-principle model is proposed to study the electrostatic properties of a double-gated silicon slab of nano scale in the framework of density functional theory. The applied gate voltage is approximated as a variation of the electrostatic potential on the boundary of the supercell enclosing the system. With the electron density estimated by the real space Green's functions, efficient multigrid and fast Fourier Poisson solvers are employed to calculate the electrostatic potential from the charge density. In the representation of localized SIESTA linear combination of atomic orbitals, the Ko…
Alloying of In/Zn oxides with various X atoms stabilizes the IXZO structures but generates electron traps in the compounds, degrading the electron mobility. To assess whether the latter is linked to the oxygen affinity or the ionic radius, of the X element, several IXZO samples are synthesized by the sol-gel process, with a large number (14) of X elements. The IXZOs are characterized by XPS, SIMS, DRX, and UV-spectroscopy and used for fabricating thin film transistors. Channel mobility and the interface defect density NST, extracted from the TFT electrical characteristics and low frequency noi…
Magnetoelectric coupling in ferromagnet/multiferroic systems is often manifested in the exchange bias effect, which may have combined contributions from multiple sources, such as domain walls, chemical defects or strain. In this study we magnetically "fingerprint" the coupling behavior of CoFe grown on epitaxial BiFeO3 (BFO) thin films by magnetometry and first-order-reversal-curves (FORC). The contribution to exchange bias from 71°, 109° and charged ferroelectric domain walls (DWs) was elucidated by the FORC distribution. CoFe samples grown on BFO with 71° DWs only exhibit an enhancement of t…
Silicon dioxide and silicon (SiO$_{2}$/Si) interface plays a very important role in semiconductor industry. However, at nanoscale, its interfacial thermal properties haven't been well understood so far. In this paper, we systematically study the interfacial thermal resistance (Kapitza resistance) of a heterojunction composed of amorphous silicon dioxide and crystalline silicon by using molecular dynamics simulations. Numerical results have shown that Kapitza resistance at SiO$_{2}$/Si interface depends on the interfacial coupling strength remarkably. In the weak interfacial coupling limit, Kap…
We have fabricated air-stable n-type, ambipolar carbon nanotube field effect transistors (CNFETs), and used them in nanoscale memory cells. N-type transistors are achieved by annealing of nanotubes in hydrogen gas and contacting them by cobalt electrodes. Scanning gate microscopy reveals that the bulk response of these devices is similar to gold-contacted p-CNFETs, confirming that Schottky barrier formation at the contact interface determines accessibility of electron and hole transport regimes. The transfer characteristics and Coulomb Blockade (CB) spectroscopy in ambipolar devices show stron…
We report amplification of biomolecular recognition signal in lithographically defined silicon nanochannel devices. The devices are configured as field effect transistors (FET) in the reversed source-drain bias region. The measurement of the differential conductance of the nanowire channels in the FET allows sensitive detection of changes in the surface potential due to biomolecular binding. Narrower silicon channels demonstrate higher sensitivity to binding due to increased surface-to-volume ratio. The operation of the device in the negative source-drain region demonstrates signal amplificati…
The interface properties of interest in multilayers include interfacial charge densities, dipole densities, band offsets, and screening-lengths, among others. Most such properties are inaccesible to direct measurements, but are key to understanding the physics of the multilayers. They are contained within first-principles electronic structure computations but are buried within the vast amount of quantitative information those computations generate. Thus far, they have been extracted from the numerical data by heuristic nanosmoothing procedures which do not necessarily provide results independe…
Two-dimensional (2D) semiconducting transition metal dichalcogenides (TMDs) are good candidates for high-performance flexible electronics. However, most demonstrations of such flexible field-effect transistors (FETs) to date have been on the micron scale, not benefitting from the short-channel advantages of 2D-TMDs. Here, we demonstrate flexible monolayer MoS2 FETs with the shortest channels reported to date (down to 50 nm) and remarkably high on-current (up to 470 uA/um at 1 V drain-to-source voltage) which is comparable to flexible graphene or crystalline silicon FETs. This is achieved using…
We report that the electrical conductance between closely-spaced gold electrodes in acid solution can be turned from off [insulating; I] to on [conducting; C] to off again by monotonically sweeping a gate voltage applied to the solution. We propose that this ICI transistor action is due to an electrochemical process dependent on nanoparticles etched from the surface of the gold electrodes. These measurements mimic closely the characteristics of nanoscale acid-gated polyaniline transistors, so that researchers should guard against misinterpreting this effect in future molecular-electronics expe…
The inter-device mismatch and intra-device temporal instability in the nanoscale CMOS circuits is examined from a unified point of view as a static and dynamic parts of the variability con-cerned with stochastic oxide charge trapping and de-trapping. This approach has been benchmarked on the recent evidence of the radiation-induced increase of inter-transistor mismatch in 60 nm ICs. A possible reliability limitation in ultrascale circuits concerned with the single or a few charged defect instability is pointed out and estimated.
Layered chalcogenides including Bi2Te3, Sb2Te3, Bi-Sb-Te ternary alloys and heterostructures are known as great thermoelectric, topological insulators and recently highlighted as plasmonic building blocks beyond noble metals. Here, we conduct a joint in situ transmission electron microscopy (in situ TEM) and density functional theory (DFT) calculations to investigate the temperature dependent nanoscale dynamics, interfacial properties and further identifying the role of native defects and edge configurations in anisotropic sublimations of Bi2Te3-Sb2Te3 in-plane heterostructure and Sb2-xBixTe3 …
Nanoscale semiconductor materials have been extensively investigated as the channel materials of transistors for energy-efficient low-power logic switches to enable scaling to smaller dimensions. On the opposite end of transistor applications is power electronics for which transistors capable of switching very high voltages are necessary. Miniaturization of energy-efficient power switches can enable the integration with various electronic systems and lead to substantial boosts in energy efficiency. Nanotechnology is yet to have an impact in this arena. In this work, it is demonstrated that nan…
Watching a GaN Transistor Switch: Real-Time Nanoscale Strain and Heat Dynamics
ESRF – The European Synchrotron（欧洲同步辐射光源）；KAI GmbH - Kompetenzzentrum Automobil- und Industrieelektronik（汽车与工业电子能力中心有限公司）；IKTS - Fraunhofer-Institut für Keramische Technologien und Systeme（弗劳恩霍夫陶瓷技术与系统研究所）；Infineon Technologies AG（英飞凌科技有限公司）；Infineon Technologies Austria AG（奥地利英飞凌科技有限公司）；Institute of Solid State Electronics, TU Wien（维也纳工业大学固态电子学研究所）
Over the past several years, the inherent scaling limitations of electron devices have fueled the exploration of high carrier mobility semiconductors as a Si replacement to further enhance the device performance. In particular, compound semiconductors heterogeneously integrated on Si substrates have been actively studied, combining the high mobility of III-V semiconductors and the well-established, low cost processing of Si technology. This integration, however, presents significant challenges. Conventionally, heteroepitaxial growth of complex multilayers on Si has been explored. Besides compl…
In recent years, three-dimensional GaN-based transistors have been intensively studied for their dramatically improved output power, better gate controllability, and shorter channels for speedup and miniaturization. However, thermal analysis of such devices is often oversimplified using the conventional Fourier's law and bulk material properties in thermal simulations. In this aspect, accurate temperature predictions can be achieved by coupled phonon and electron Monte Carlo simulations that track the movement and scattering of individual phonons and electrons. However, the heavy computational…
Graphene field-effect transistors with source/drain contacts made of metals that can be easily oxidized such as ferromagnetic metals often display a double dip structure in the transfer characteristics because of charge density depinning at the contacts. Generally, transfer characteristics of field-effect transistors show no dependence on the length of the source/drain contacts because charge carrier injection occurs mainly at the edges of the contact. However, the shape of the transfer characteristics of devices fabricated using Ni contacts is found to be dependent on the length of the contac…
Direct observations using scanning transmission electron microscopy unveil an intriguing interfacial bi-layer that enables epitaxial growth of a strain-free, monoclinic, bronze-phase VO2(B) thin film on a perovskite SrTiO3 (STO) substrate. We observe an ultrathin (2-3 unit cells) interlayer best described as highly strained VO2(B) nanodomains combined with an extra (Ti,V)O2 layer on the TiO2 terminated STO (001) surface. By forming a fully coherent interface with the STO substrate and a semi-coherent interface with the strain-free epitaxial VO2(B) film above, the interfacial bi-layer enables t…
Single electron transistors (SETs) made from single wall carbon nanotubes (SWCNTs) are promising for quantum electronic devices operating with ultra-low power consumption and allow fundamental studies of electron transport. We report on SETs made by registered in-plane growth utilizing tailored nanoscale catalyst patterns and chemical vapor deposition. Metallic SWCNTs have been removed by an electrical burn-in technique and the common gate hysteresis was removed using PMMA and baking, leading to field effect transistors with large on/off ratios up to 10^5. Further segmentation into 200 nm shor…
Intertwined bulk photocarrier and interfacial barrier dynamics in van der Waals point-contact Schottky junctions
UNISOKU Co., Ltd.（UNISOKU有限公司）；Faculty of Pure and Applied Sciences, University of Tsukuba（筑波大学理学院）；Department of Fundamental Biosciences (Physics), Shiga University of Medical Science（滋贺医科大学基础生命科学系（物理））；Institute for Molecular Science (IMS), National Institutes of Natural Sciences（国立自然科学研究所分子科学研究所）
With the rapid advances in the development of nanotechnology, nowadays, the sizes of elementary unit, i.e. transistor, of micro- and nanoelectronic devices are well deep into nanoscale. For the pursuit of cheaper and faster nanoscale electronic devices, the size of transistors keeps scaling down. As the miniaturization of the nanoelectronic devices, the electrical resistivity increases dramatically, resulting rapid growth in the heat generation. The heat generation and limited thermal dissipation in nanoscale materials have become a critical problem in the development of the next generation na…
The object of this article is to review the development of ultrahigh-density, nanoscale data storage, i.e., nanostorage. As a fundamentally new type of storage system, the recording mechanisms of nanostorage may be completely different to those of the traditional devices. Currently, two types of molecules are being studied for potential application in nanostorage. One is molecular electronic elements including molecular wires, rectifiers, switches, and transistors. The other approach employs nanostructured materials such as nanotubes, nanowires, and nanoparticles. The challenges for nanostorag…
Ferroelectric field-effect transistors (FE-FETs) consisting of tunable dielectric layers are utilized to investigate interfacial transport processes. Large changes in the dielectric constant as a function of temperature are observed in FE-FETs in conjunction with the ferroelectric to paraelectric transition. The devices offer a test bed to evaluate specific effects of polarization on the electrical processes. FE-FETs have dominant contributions from polarization-fluctuation rather than static dipolar disorder prevalent in high k paraelectric dielectric-based FETs. Additionally, photo-excitatio…
Chemical segregation and structural transitions at interfaces are important nanoscale phenomena, making them natural targets for atomistic modeling, yet interatomic potentials must be fit to secondary physical properties. To isolate the important factors that interatomic potentials must capture in order to accurately model such behavior, the performance of four interatomic potentials was evaluated for the Cu-Zr system, with experimental observations used to provide validation. While experimental results show strong Zr segregation to grain boundary regions and the formation of nanoscale amorpho…
In 2D-semiconductor-based field-effect transistors and optoelectronic devices, metal-semiconductor junctions are one of the crucial factors determining device performance. The Fermi-level (FL) pinning effect, which commonly caused by interfacial gap states, severely limits the tunability of junction characteristics, including barrier height and contact resistance. A tunneling contact scheme has been suggested to address the FL pinning issue in metal-2D-semiconductor junctions, whereas the experimental realization is still elusive. Here, we show that an oxidized-monolayer-enabled tunneling barr…
Silicon ferroelectric field-effect transistors (FeFETs) with low-k interfacial layer (IL) between ferroelectric gate stack and silicon channel suffers from high write voltage, limited write endurance and large read-after-write latency due to early IL breakdown and charge trapping and detrapping at the interface. We demonstrate low voltage, high speed memory operation with high write endurance using an IL-free back-end-of-line (BEOL) compatible FeFET. We fabricate IL-free FeFETs with 28nm channel length and 126nm width under a thermal budget <400C by integrating 5nm thick Hf0.5Zr0.5O2 gate stac…
Atomically thin monolayers of graphene show excellent electronic properties which have led to a great deal of research on their use in nanoscale devices. However, heat management of such nanoscale devices is essential in order to improve their performance. Graphene supported on hexagonal boron nitride (h-BN) substrate has been reported to show enhanced (opto)electronic and thermal properties as compared to extensively used SiO2/Si supported graphene. Motivated by this, we have performed temperature- and power-dependent Raman Spectroscopic measurements on four different types of (hetero)structu…
Controlling the flow of charge neutral interlayer exciton (IX) quasiparticles can potentially lead to low loss excitonic circuits. Here, we report unidirectional transport of IXs along nanoscale electrostatically defined channels in an MoSe$_2$-WSe$_2$ heterostructure. These results are enabled by a lithographically defined triangular etch in a graphene gate to create a potential energy ''slide''. By performing spatially and temporally resolved photoluminescence measurements, we measure smoothly varying IX energy along the structure and high-speed exciton flow with a drift velocity up to 2 * 1…
The metal-insulator transition (MIT) in vanadium dioxide (VO2) has the potential to lead to a number of disruptive technologies, including ultra-fast data storage, optical switches, and transistors which move beyond the limitations of silicon. For applications, VO2 films are deposited on crystalline substrates to prevent cracking observed in bulk VO2 crystals across the thermally driven MIT. Near the MIT, VO2 films exhibit nanoscale coexistence between metallic and insulating phases, which opens up further potential applications such as memristors, tunable capacitors, and optically engineered …
We report on infrared (IR) spectro-microscopy of the electronic excitations in nanometer-thick accumulation layers in FET devices based on poly(3-hexylthiophene). IR data allows us to explore the charge injection landscape and uncovers the critical role of the gate insulator in defining relevant length scales. This work demonstrates the unique potential of IR spectroscopy for the investigation of physical phenomena at the nanoscale occurring at the semiconductor-insulator interface in FET devices.
When transistor gate insulators have nanometer-scale equivalent oxide thickness (EOT), the gate capacitance ($C_\textrm{G}$) becomes smaller than the oxide capacitance ($C_\textrm{ox}$) due to the quantum capacitance and charge centroid capacitance of the channel. Here, we study the capacitance of monolayer MoS$_\textrm{2}$ as a prototypical two-dimensional (2D) channel while considering spatial variations in the potential, charge density, and density of states. At 0.5 nm EOT, the monolayer MoS$_\textrm{2}$ capacitance is smaller than its quantum capacitance, limiting the single-gated $C_\text…
At the LaAlO$_3$-SrTiO$_3$ interface, electronic phase transitions can be triggered by modulation of the charge carrier density, making this system an excellent prospect for the realization of versatile electronic devices. Here, we report repeatable transistor operation in locally gated LaAlO$_3$-SrTiO$_3$ field-effect devices of which the LaAlO$_3$ dielectric is only four unit cells thin, the critical thickness for conduction at this interface. This extremely thin dielectric allows a very efficient charge modulation of ${\sim}3.2\times10^{13}$ cm$^{-2}$ within a gate-voltage window of $\pm1$ …
Accurate prediction of interfacial slip in nanoscale channels is required by many microfluidic applications. Existing hydrodynamic solutions based on Maxwellian boundary conditions include an empirical parameter that depends on material properties and pore dimensions. This paper presents a derivation of a new expression for the slip coefficient that is not based on the assumptions concerning the details of solid-fluid collisions and whose parameters are obtainable from \textit{equilibrium} simulation. The results for the slip coefficient and flow rates are in good agreement with non-equilibriu…
Revealing the Atomic-Scale Structure of the Copper Sulfuric Acid Interface
Max Planck Institute for Sustainable Materials（马克斯·普朗克可持续材料研究所）；Gyeongsang National University（庆尚国立大学）；Imperial College London（伦敦帝国理工学院）；University of Toronto（多伦多大学）；Univ Rouen Normandie, CNRS, INSA Rouen Normandie, Groupe de Physique des Matériaux（鲁昂诺曼底大学，法国国家科学研究中心，鲁昂诺曼底国立应用科学学院，物质物理研究组）；KU Leuven（荷语鲁汶大学）
Recent reports of superconductivity at KTaO3 (KTO) (110) and (111) interfaces have sparked intense interest due to the relatively high critical temperature as well as other properties that distinguish this system from the more extensively studied SrTiO3 (STO)-based heterostructures. Here we report nanoscale control of the metal-to-insulator transition at the LaAlO3/KTO (110) and (111) interfaces. Devices are created using two distinct methods previously developed for STO-based heterostructures: (1) conductive atomic-force microscopy lithography and (2) ultra-low-voltage electron-beam lithograp…
Graphdiyne is prepared on metal surface, and making devices out of it also inevitably involves contact with metals. Using density functional theory with dispersion correction, we systematically studied for the first time the interfacial properties of graphdiyne contacting with a series of metals (Al, Ag, Cu, Au, Ir, Pt, Ni, and Pd). Graphdiyne is in an n-type Ohmic or quasi-Ohmic contact with Al, Ag, and Cu, while it is in a Schottky contact with Au (at source/drain interface), Pd, Pt, Ni, and Ir (at source/drain-channel interface), with high Schottky barrier heights of 0.39, 0.21 (n-type), 0.…
Nanoscale molecular junctions are celebrated nanoelectronic devices for mimicking several electronic functions including rectifiers, sensors, wires, switches, transistors, and memory but capacitive behavior is nearly unexplored. Capacitors are crucial energy storage devices that store energy in the form of electrical charges. A capacitor utilizes two electrical conductors separated by a dielectric material. However, many oxides-based dielectrics are well-studied for integrating capacitors, however, capacitors comprised of thin-film molecular layers are not well-studied. The present work descri…
Using field-emission resonance spectroscopy with an ultrahigh vacuum scanning tunneling microscope, we reveal Stark-shifted image-potential states of the v_1/6 and v_1/5 borophene polymorphs on Ag(111) with long lifetimes, suggesting high borophene lattice and interface quality. These image-potential states allow the local work function and interfacial charge transfer of borophene to be probed at the nanoscale and test the widely employed self-doping model of borophene. Supported by apparent barrier height measurements and density functional theory calculations, electron transfer doping occurs…
Investigation of the interfacial electronic properties of N,N'-bis(n-octyl)-(1,7&1,6)-dicyanoperylene-3,4:9,10-bisdicarboximide (PDI8-CN2) organic semiconductor films grown on silicon dioxide is performed by polarization-resolved second harmonic generation optical spectroscopy, pointing out a spatial region where charge carriers distribution in the semiconductor lacks inversion symmetry. By developing a model for nonlinear susceptibility in the framework of Debye-Huckel screening theory, we show that the experimental findings can be interpreted as resulting from the presence of a net charge lo…
