The aim of this paper is to characterize the uniqueness domains in the workspace of parallel manipulators, as well as their image in the joint space. The notion of aspect introduced for serial manipulators in [Borrel 86] is redefined for such parallel manipulators. Then, it is shown that it is possible to link several solutions to the direct kinematic problem without meeting a singularity, thus meaning that the aspects are not uniqueness domains. Additional surfaces are characterized in the workspace which yield new uniqueness domains. An octree model of spaces is used to compute the joint space, the workspace and all other newly defined sets. This study is illustrated all along the paper with a 3-RPR planar parallel manipulator.
Presented in this paper is the kinematic analysis of a symmetrical three-degree-of-freedom planar parallel manipulator. In opposite to serial manipulators, parallel manipulators can admit not only multiple inverse kinematic solutions, but also multiple direct kinematic solutions. This property produces more complicated kinematic models but allows more flexibility in trajectory planning. To take into account this property, the notion of aspects, i.e. the maximal singularity-free domains, was introduced, based on the notion of working modes, which makes it possible to separate the inverse kinema…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
Positioning 3R manipulators may have two or four inverse kinematic solutions (IKS). This paper derives a necessary and sufficient condition for 3R positioning manipulators with orthogonal joint axes to have four distinct IKS. We show that the transition between manipulators with 2 and 4 IKS is defined by the set of manipulators with a quadruple root of their inverse kinematics. The resulting condition is explicit and states that the last link length of the manipulator must be greater than a quantity that depends on three of its remaining DH-parameters. This result is of interest for the design…
McGill University（麦吉尔大学）；INRIA Rocquencourt（法国国家信息与自动化研究所罗克库尔分部）；Centre for Intelligent Machines（智能机器中心）
The paper discusses the kinematics of manipulators builts of planar closed kinematic chains. A special kinematic scheme is extracted from the array of these mechanisms that looks the most promising for the creation of different types of robotic manipulators. The structural features of this manipulator determine a number of its original properties that essentially simplify its control. These features allow the main control problems to be effectively overcome by application of the simple kinematic problems. The workspace and singular configurations of a basic planar manipulator are studied. By u…
Oregon State University（俄勒冈州立大学）；University of Massachusetts Amherst（马萨诸塞大学阿默斯特分校）；Olin College of Engineering（奥林工程学院）
We present a novel general model that unifies the kinematics of constant curvature and constant twist continuum manipulators. Combining this kinematics with energy-based physics, we derive a linear mapping from actuator configuration to manipulator deformation that is analogous to traditional robot forward kinematics. Our model generalizes across manipulators with different sizes, types of bending, and types of actuators, without the need for parameter re-fitting. The combination of generality and linearity makes the model useful for control and planning algorithms. Finally, our model is shown…
The aim of this paper is the kinematic study of a 3-RPR planar parallel manipulator where the three fixed revolute joints are actuated. The direct and inverse kinematic problem as well as the singular configuration is characterized. On parallel singular configurations, the motion produce by the mobile platform can be compared to the Reuleaux straight-line mechanism.
Institut de Recherche en Cybernétique de Nantes（南特控制论研究所）；École Centrale de Nantes（南特中央理工学院）
The aim of this paper is to characterize the notion of aspect in the workspace and in the joint space for parallel manipulators. In opposite to the serial manipulators, the parallel manipulators can admit not only multiple inverse kinematic solutions, but also multiple direct kinematic solutions. The notion of aspect introduced for serial manipulators in [Borrel 86], and redefined for parallel manipulators with only one inverse kinematic solution in [Wenger 1997], is redefined for general fully parallel manipulators. Two Jacobian matrices appear in the kinematic relations between the joint-rat…
A class of analytic planar 3-RPR manipulators is analyzed in this paper. These manipulators have congruent base and moving platforms and the moving platform is rotated of 180 deg about an axis in the plane. The forward kinematics is reduced to the solution of a 3rd-degree polynomial and a quadratic equation in sequence. The singularities are calculated and plotted in the joint space. The second-order singularities (cups points), which play an important role in non-singular change of assembly-mode motions, are also analyzed.
Aerial robotic systems have raised emerging interests in recent years. In this article, we propose a novel aerial manipulator system that is significantly different from conventional aerial discrete manipulators: An Aerial Continuum Manipulator (AeCoM). The AeCoM compactly integrates a quadrotor with a tendon-driven continuum robotic manipulator. Due to the compact design and the payload bearing ability of tendon-driven continuum robotic arms, the proposed system solved the conflict between payload capacity and dexterity lying in conventional aerial manipulators. Two contributions are made in …
Institut de Recherche en Cybernétique de Nantes (IRCyN)（南特控制论研究所）；McGill University（麦吉尔大学）
This paper focuses on the kinematic properties of a new three-degree-of-freedom hybrid manipulator. This manipulator is obtained by adding in series to a five-bar planar mechanism (similar to the one studied by Bajpai and Roth) a third revolute passing through the line of centers of the two actuated revolute joints of the above linkage. The resulting architecture is hybrid in that it has both serial and parallel links. Fully-parallel manipulators are known for the existence of particularly undesirable singularities (referred to as parallel singularities) where control is lost [4] and [6]. On t…
This work addresses the problem of kinematic trajectory planning for mobile manipulators with non-holonomic constraints, and holonomic operational-space tracking constraints. We obtain whole-body trajectories and time-varying kinematic feedback controllers by solving a Constrained Sequential Linear Quadratic Optimal Control problem. The employed algorithm features high efficiency through a continuous-time formulation that benefits from adaptive step-size integrators and through linear complexity in the number of integration steps. In a first application example, we solve kinematic trajectory p…
Predictive Kinematic Coordinate Control for Aerial Manipulators based on Modified Kinematics Learning
College of Computer Science and Technology, Zhejiang University（浙江大学计算机科学与技术学院）；Westlake University（西湖大学）；Westlake Institute for Optoelectronics（西湖光电研究院）
Laboratoire des Sciences du Numérique de Nantes（南特数字科学实验室）；Ecole Centrale Nantes（南特中央理工学院）；IMT Atlantique（IMT大西洋）；Innopolis University（因诺波利斯大学）；Centre National de la Recherche Scientifique (CNRS)（法国国家科学研究中心）
The paper focuses on the kinematics control of a compliant serial manipulator composed of a new type of dualtriangle elastic segments. Some useful optimization techniques were applied to solve the geometric redundancy problem, ensure the stability of the manipulator configurations with respect to the external forces/torques applied to the endeffector. The efficiency of the developed control algorisms is confirmed by simulation.
Institut de Recherche en Communications et Cybernetique de Nantes（南特通信与控制论研究所）；Ecole des Mines de Nantes（南特国立高等矿业学校）；University of Agder（阿格德大学）
The paper is devoted to the compliance errors compensation for parallel manipulators under external loading. Proposed approach is based on the non-linear stiffness modeling and reduces to a proper adjusting of a target trajectory. In contrast to previous works, in addition to compliance errors caused by machining forces, the problem of assembling errors caused by inaccuracy in the kinematic chains is considered. The advantages and practical significance of the proposed approach are illustrated by examples that deal with groove milling with Orthoglide manipulator.
This paper investigates two situations in which the forward kinematics of planar 3-RPR parallel manipulators degenerates. These situations have not been addressed before. The first degeneracy arises when the three input joint variables r1, r2 and r3 satisfy a certain relationship. This degeneracy yields a double root of the characteristic polynomial in t, which could be erroneously interpreted as two coalesce assembly modes. But, unlike what arises in non-degenerate cases, this double root yields two sets of solutions for the position coordinates (x, y) of the platform. In the second situation…
Australian Centre for Robotic Vision（澳大利亚机器人视觉中心）；Queensland University of Technology（昆士兰科技大学）
The elementary transform sequence (ETS) provides a universal method of describing the kinematics of any serial-link manipulator. The ETS notation is intuitive and easy to understand, while avoiding the complexity and limitations of Denvit-Hartenberg frame assignment. In this paper, we describe a systematic method for computing the manipulator Jacobian and Hessian (differential kinematics) using the ETS notation. Differential kinematics have many applications including numerical inverse kinematics, resolved-rate motion control and manipulability motion control. Furthermore, we provide an open-s…
This paper discusses modelling two 6 DOF arm robots. The first step of modelling a robot is establishing its Denavit-Hartenberg parameters. It requires assigning proper coordinates for each link and finding their exact dimensions. In this project we will develop the direct kinematics and workspace representations for two manipulators: the Smokie Robot and the Barrett WAM. After finding the D-H parameters and creating Transformation Matrices,MATLAB programming is used to represent their workspaces.
School of Artificial Intelligence and Automation, Huazhong University of Science and Technology（华中科技大学人工智能与自动化学院）；School of Automation, South East University（东南大学自动化学院）
The traditional kinematic calibration method for manipulators requires precise three-dimensional measuring instruments to measure the end pose, which is not only expensive due to the high cost of the measuring instruments but also not applicable to all manipulators. Another calibration method uses a camera, but the system error caused by the camera's parameters affects the calibration accuracy of the kinematics of the robot arm. Therefore, this paper proposes a method for calibrating the geometric parameters of a kinematic model of a manipulator based on monocular vision. Firstly, the classic …
Belarusian State University of Informatics and Radioelectronics（白俄罗斯信息与无线电电子大学）；Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
The paper addresses kinematic and geometrical aspects of the Orthoglide, a three-DOF parallel mechanism. This machine consists of three fixed linear joints, which are mounted orthogonally, three identical legs and a mobile platform, which moves in the Cartesian x-y-z space with fixed orientation. New solutions to solve inverse/direct kinematics are proposed and we perform a detailed workspace and singularity analysis, taking into account specific joint limit constraints.
École Centrale de Nantes（南特中央理工学院）；Université de Nantes（南特大学）
This work investigates new kinematic features of parallel manipulators. It is well known that parallel manipulators admit generally several direct kinematic solutions for a given set of input joint values. The aim of this paper is to characterize the uniqueness domains in the workspace of parallel manipulators, as well as their image in the joint space. The study focuses on the most usual case of parallel manipulators with only one inverse kinematic solution. The notion of aspect introduced for serial manipulators in [Borrel 86] is redefined for such parallel manipulators. Then, it is shown th…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
The workspace topologies of a family of 3-revolute (3R) positioning manipulators are enumerated. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps that appear on these singular curves. The design parameters space is shown to be divided into five domains where all manipulators have the same number of cusps. Each separating surface is given as an explicit expression in the DH-parameters. As an application of this work, we provide a necessary and sufficient condition for a 3R orthogonal manipulator to be cuspida…
This paper discusses deriving geometric jacobians and identifying and analyzing the kinematic singularities for two 6 DOF arm robots. First we show the direct kinematics and D-H parameters derived for these two arms. The Geometric jacobian is computed for Barrett WAM and Smokie OUR. By analyzing the jacobian matrices we find the configurations at which J is rank deficient and derive the kinematic singularities through jacobian's determinent. Schematic are provided to show the singular configurations of both robots. Finally a survey is done on redundant kinematic allocation schemesfor 7 DoF Bar…
IMT Atlantique Bretagne Pays de la Loire（大西洋布列塔尼卢瓦尔河国家高等矿业电信学校）；Centre National de la Recherche Scientifique (CNRS)（法国国家科学研究中心）
The paper focuses on the redundancy resolution in kinematic control of a new type of serial manipulator composed of multiple tensegrity segments, which are moving in a multi-obstacle environment. The general problem is decomposed into two sub-problems, which deal with collision-free path planning for the robot end-effector and collision-free motion planning for the robot body. The first of them is solved via discrete dynamic programming, the second one is worked out using quadratic programming with mixed linear equality/nonequality constraints. Efficiency of the proposed technique is confirmed…
Institut de Recherche en Communication et Cybernétique de Nantes（南特通信与控制研究所）
This paper deals with the kinematic and dynamic analyses of the Orthoglide 5-axis, a five-degree-of-freedom manipulator. It is derived from two manipulators: i) the Orthoglide 3-axis; a three dof translational manipulator and ii) the Agile eye; a parallel spherical wrist. First, the kinematic and dynamic models of the Orthoglide 5-axis are developed. The geometric and inertial parameters of the manipulator are determined by means of a CAD software. Then, the required motors performances are evaluated for some test trajectories. Finally, the motors are selected in the catalogue from the previou…
This paper analyses the workspace of the three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. These manipulators are classified into different groups with similar kinematic properties. The classification criteria are based on the topology of the workspace. Each group is evaluated according to interesting kinematic properties such as the size of the workspace subregion reachable with four inverse kinematic solutions, the existence and the size of voids, and the size of the regions of feasible paths in the workspace.
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）；McGill University（麦吉尔大学）
The subject of this paper is a special class of parallel manipulators. First, we analyze a family of three-degree-of-freedom manipulators. Two Jacobian matrices appear in the kinematic relations between the joint-rate and the Cartesian-velocity vectors, which are called the "inverse kinematics" and the "direct kinematics" matrices. The singular configurations of these matrices are studied. The isotropic configurations are then studied based on the characteristic length of this manipulator. The isoconditioning loci of all Jacobian matrices are computed to define a global performance index to co…
Computer Science and Engineering Department, University of South Carolina（南卡罗来纳大学计算机科学与工程系）；Department of Mechanical Engineering, National Technical University of Athens（雅典国立技术大学机械工程系）
A hyper-redundant robotic arm is a manipulator with many degrees of freedom, capable of executing tasks in cluttered environments where robotic arms with fewer degrees of freedom are unable to operate. This paper introduces a new method for modeling those manipulators in a completely dynamic way. The proposed method enables online changes of the kinematic structure with the use of a special function; termed "meta-controlling function". This function can be used to develop policies to reduce drastically the computational cost for a single task, and to robustly control the robotic arm, even in t…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
This paper presents an algorithm for detecting and computing the cusp points in the joint space of 3-RPR planar parallel manipulators. In manipulator kinematics, cusp points are special points, which appear on the singular curves of the manipulators. The nonsingular change of assembly mode of 3-RPR parallel manipulators was shown to be associated with the existence of cusp points. At each of these points, three direct kinematic solutions coincide. In the literature, a condition for the existence of three coincident direct kinematic solutions was established, but has never been exploited, becau…
University of Toronto Institute for Aerospace Studies（多伦多大学航空航天研究所）；University of Zagreb（萨格勒布大学）
We present a novel approach for mobile manipulator self-calibration using contact information. Our method, based on point cloud registration, is applied to estimate the extrinsic transform between a fixed vision sensor mounted on a mobile base and an end effector. Beyond sensor calibration, we demonstrate that the method can be extended to include manipulator kinematic model parameters, which involves a non-rigid registration process. Our procedure uses on-board sensing exclusively and does not rely on any external measurement devices, fiducial markers, or calibration rigs. Further, it is full…
IRCCyN, Institut de Recherche en Communications et Cybernetique de Nantes（南特通信与控制研究所（IRCCyN））；McGill University（麦吉尔大学）
This paper proposes a classification of three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. This classification is based on the topology of their workspace. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps and nodes that appear on these singular curves. The manipulators are classified into different types with similar kinematic properties. Each type is evaluated according to interesting kinematic properties such as, whether the workspace is fully reachable with…
A polynomial solution to the inverse kinematic problem of the Kinova Gen3 Lite robot is proposed in this paper. This serial robot is based on a 6R kinematic chain and is not wrist-partitioned. We first start from the forward kinematics equation providing the position and orientation of the end-effector, finally, the univariate polynomial equation is given as a function of the first joint variable $θ_{1}$. The remaining joint variables are computed by back substitution. Thus, an unique set of joint position is obtain for each root of the univariate equation. Numerical examples, simulated in ROS…
Institut de Recherche en Cybernétique de Nantes（南特控制论研究所）；École Centrale de Nantes（南特中央理工学院）；McGill University（麦吉尔大学）
The subject of this paper is a special class of closed-chain manipulators. First, we analyze a family of two-degree-of-freedom (dof) five-bar planar linkages. Two Jacobian matrices appear in the kinematic relations between the joint-rate and the Cartesian-velocity vectors, which are called the ``inverse kinematics" and the "direct kinematics" matrices. It is shown that the loci of points of the workspace where the condition number of the direct-kinematics matrix remains constant, i.e., the isoconditioning loci, are the coupler points of the four-bar linkage obtained upon locking the middle joi…
Multimodal Control of Manipulators: Coupling Kinematics and Vision for Self-Driving Laboratory Operations
1 Department of Electronics Systems, Aalborg University, Denmark；3 Extreme Robotics Laboratory, School of Metallurgy \& Materials, University of Birmingham, Birmingham, United Kingdom
Harbin Institute of Technology（哈尔滨工业大学）；University of Maryland at College Park（马里兰大学帕克分校）
We present a novel algorithm for collision-free kinematics of multiple manipulators in a shared workspace with moving obstacles. Our optimization-based approach simultaneously handles collision-free constraints based on reciprocal velocity obstacles and inverse kinematics constraints for high-DOF manipulators. We present an efficient method based on particle swarm optimization that can generate collision-free configurations for each redundant manipulator. Furthermore, our approach can be used to compute safe and oscillation-free trajectories in a few milli-seconds. We highlight the real-time p…
Egypt-Japan University of Science and Technology（埃及-日本科学技术大学）
This paper presents the inverse kinematic analysis and parameters identification of a novel aerial manipulation system. This system consists of 2-link manipulator attached to the bottom of a quadrotor. This new system presents a solution for the limitations found in the current quadrotor manipulation system. By deriving the inverse kinematics, one can design the controller such that the desired end effector position and orientation can be tracked. To study the feasibility of the proposed system, a quadrotor with high enough payload to add the 2-link manipulator is designed and constructed. Exp…
Stable Tracking-in-the-Loop Control of Cable-Driven Surgical Manipulators under Erroneous Kinematic Chains
Department of Electrical and Computer Engineering, University of California San Diego（电子工程与计算机科学系，加州大学圣地亚哥分校）；Department of Electrical Engineering and Computer Science, University of Tennessee Knoxville（电子工程与计算机科学系，田纳西大学基洛纳分校）
The direct kinematics analysis is the foundation of implementation of real world application of parallel manipulators. For most parallel manipulators the direct kinematics is challenging. In this paper, for the first time a fast and efficient Homotopy Continuation Method, called the Ostrowski Homotopy continuation method has been implemented to solve the direct and inverse kinematics problem of the parallel manipulators. This method has advantage over conventional numerical iteration methods, which is not rely on the initial values and is more efficient than other continuation method and it ca…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
This paper deals with the optimal path placement for a manipulator based on energy consumption. It proposes a methodology to determine the optimal location of a given test path within the workspace of a manipulator with minimal electric energy used by the actuators while taking into account the geometric, kinematic and dynamic constraints. The proposed methodology is applied to the Orthoglide~3-axis, a three-degree-of-freedom translational parallel kinematic machine (PKM), as an illustrative example.
This paper describes a unified method solving for inverse, forward, and hybrid dynamics problems for robotic manipulators with either open kinematic chains or closed kinematic loops based on factor graphs. Manipulator dynamics is considered to be a well studied problem, and various different algorithms have been developed to solve each type of dynamics problem. However, they are not easily explained in a unified and intuitive way. In this paper, we introduce factor graphs as a unifying graphical language in which not only to solve all types of dynamics problems, but also explain the classical …
This paper explores the possibility of improving bilateral robot manipulation task performance through optimizing the robot morphology and configuration of the system through motion. To optimize the design for different scenarios, we select a set of tasks that represent the variability in small scale manipulation (e.g. pick and place, tasks involving positioning and orientation) and track the motion to obtain a reproducible trajectory. Kinematic data is captured through an electromagnetic (EM) tracker system while a human subject performs the tasks. Then, the data is pre-processed and used to …
Research Institute for Symbolic Computation, Johannes Kepler University（约翰内斯·开普勒大学符号计算研究所）；University of the Philippines Diliman（菲律宾大学迪里曼分校）
We develop an algorithm that solves the inverse kinematics of general serial 2RP3R, 2R2P2R, 3RP2R and 6R manipulators based on the HuPf algorithm. We identify the workspaces of the 3-subchains of the manipulator with a quasi-projective variety in $\mathbb{P}^7$ via dual quaternions. This allows us to compute linear forms that describe linear spaces containing the workspaces of these 3-subchains. We present numerical examples that illustrate the algorithm and show the real solutions.
Sensor-Space Based Robust Kinematic Control of Redundant Soft Manipulator by Learning
Department of Mechanical and Aerospace Engineering, The University of Manchester, Manchester, United Kingdom（机械与航空航天工程系，曼彻斯特大学，英国曼彻斯特）；Department of Electrical and Electronic Engineering, The University of Manchester, Manchester, United Kingdom（电气与电子工程系，曼彻斯特大学，英国曼彻斯特）
Changzhou University（常州大学）；Nanjing Vocational Institute of Mechatronic Technology（南京机电职业技术学院）；Dalian University of Technology（大连理工大学）；Laboratoire des Sciences du Numérique de Nantes (LS2N)（南特数字科学实验室）
This paper presents a novel three-degree-of-freedom (3-DOF) translational parallel manipulator (TPM) by using a topological design method of parallel mechanism (PM) based on position and orientation characteristic (POC) equations. The proposed PM is only composed of lower-mobility joints and actuated prismatic joints, together with the investigations on three kinematic issues of importance. The first aspect pertains to geometric modeling of the TPM in connection with its topological characteristics, such as the POC, degree of freedom and coupling degree, from which its symbolic direct kinemati…
TU Wien（维也纳工业大学）；University of Liverpool（利物浦大学）；Austrian Institute of Technology GmbH (AIT)（奥地利技术研究院有限公司）
Solving the analytical inverse kinematics (IK) of redundant manipulators in real time is a difficult problem in robotics since its solution for a given target pose is not unique. Moreover, choosing the optimal IK solution with respect to application-specific demands helps to improve the robustness and to increase the success rate when driving the manipulator from its current configuration towards a desired pose. This is necessary, especially in high-dynamic tasks like catching objects in mid-flights. To compute a suitable target configuration in the joint space for a given target pose in the t…
This paper presents a kinematic definition of a serialized Stewart platform designed for autonomous in-space assembly called an Assembler. The Assemblers architecture describes problems inherent to the inverse kinematics of over-actuated mixed kinematic systems. This paper also presents a methodology for optimizing poses. In order to accomplish this with the Assembler system, an algorithm for finding a feasible solution to its inverse kinematics was developed with a wrapper for a nonlinear optimization algorithm designed to minimize the magnitude of forces incurred by each actuator. A simulate…
Considering the difficulty of students in calculating the direct and inverse kinematics of a robotic manipulator using only conventional tools of a classroom, this article proposes the application of Project Based Learning (ABP) through the design, development, mathematical modeling of a robotic manipulator as an integrative project of the disciplines of Industrial Robotics, Microcontrollers and Computer Assisted Design with students of the Control and Automation Engineering of the University of Fortaleza. Once designed and machined, the manipulator arm was assembled using servo motors connect…
University of Bengkulu（明古鲁大学）；Pusat Penelitian Elektronika dan Telekomunikasi Lembaga Ilmu Pengetahuan Indonesia（印度尼西亚科学院电子学与电信研究中心）
This paper presents the development of vision-based robotic arm manipulator control by applying Proportional Derivative-Pseudoinverse Jacobian (PD-PIJ) kinematics and Denavit Hartenberg forward kinematics. The task of sorting objects based on color is carried out to observe error propagation in the implementation of manipulator on real system. The objects image captured by the digital camera were processed based on HSV-color model and the centroid coordinate of each object detected were calculated. These coordinates are end effector position target to pick each object and were placed to the ri…
Institut de recherche en communications et cybernétique de Nantes（南特通信与控制研究所）；CNRS（法国国家科学研究中心）
This paper proposes a method to calculate the largest Regular Dextrous Workspace (RDW) of some types of three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. Then a new performance index based on the RDW is introduced, the isocontours of this index are plotted in the parameter space of the interesting types of manipulators and finally an inspection of the domains of the parameter spaces is conducted in order to identify the better manipulator architectures. The RDW is a part of the workspace whose shape is regular (cube, cylinder) and the performan…
