This paper focuses on the kinematic properties of a new three-degree-of-freedom hybrid manipulator. This manipulator is obtained by adding in series to a five-bar planar mechanism (similar to the one studied by Bajpai and Roth) a third revolute passing through the line of centers of the two actuated revolute joints of the above linkage. The resulting architecture is hybrid in that it has both serial and parallel links. Fully-parallel manipulators are known for the existence of particularly undesirable singularities (referred to as parallel singularities) where control is lost [4] and [6]. On the other hand, due to their cantilever type of kinematic arrangement, fully serial manipulators suffer from a lack of stiffness and from relatively large positioning errors. The hybrid manipulator studied is intrinsically stiffer and more accurate. Furthermore, since all actuators are located on the first axis, the inertial effects are considerably reduced. In addition, it is shown that the special kinematic structure of our manipulator has the potential of avoiding parallel singularities by a suitable choice of the "working mode", thus leading to larger workspaces. The influence of the different structural dimensions (e.g. the link lengths) on the kinematic and mechanical properties are analysed in view of the optimal design of such hybrid manipulators.
The present project deals with the elastostatic modeling and calibration experiment of spacial industrial manipulators using an optimal selection of measurements pose, for the calibration procedure, the optimal pose selection aims to the efficiency improvement of identification procedure for serial manipulators which reduces noise impact on the parameters identification precision, it is usually used for planar manipulators, our work is mainly to extend the approach for a more complicated manipulator in 3D space using a wise decomposition of the spacial manipulator into a set of serial sub-chai…
Mainly because of the heavy computational costs, the real-time whole-body obstacle avoidance for the redundant manipulators has not been well implemented. This paper presents an approach that can ensure that the whole-body of a redundant manipulator can avoid moving obstacles in real-time during the execution of a task. The manipulator is divided into end-effector and non-end-effector portion. Based on dynamical systems (DS), the real-time end-effector obstacle avoidance is obtained. Besides, the end-effector can reach the given target. By using null-space velocity control, the real-time non-e…
Dimensional synthesis refers to design of the dimensions of manipulators by optimising different kinds of performance indices. The motivation of this study is to perform dimensional synthesis for a wide set of spatial manipulators by optimising the manipulability of each manipulator around a pre-defined task point in the workspace and to finally give a prescription of manipulators along with their dimensions optimised for velocity and force transmission. A systematic method to formulate Jacobian matrix of a manipulator is presented. Optimisation of manipulability is performed for manipulation …
Huazhong University of Science and Technology（华中科技大学）；South East University（东南大学）
To realize a robust robotic grasping system for unknown objects in an unstructured environment, large amounts of grasp data and 3D model data for the object are required, the sizes of which directly affect the rate of successful grasps. To reduce the time cost of data acquisition and labeling and increase the rate of successful grasps, we developed a self-supervised learning mechanism to control grasp tasks performed by manipulators. First, a manipulator automatically collects the point cloud for the objects from multiple perspectives to increase the efficiency of data acquisition. The complet…
PCHands: PCA-based Hand Pose Synergy Representation on Manipulators with N-DoF
Humanoid Sensing and Perception (HSP), Istituto Italiano di Tecnologia (IIT)（人形感知与感知（HSP），意大利技术研究所（IIT））；Dipartimento di Informatica, Bioingegneria, Robotica e Ingegneria dei Sistemi, University of Genoa（信息学院、生物工程、机器人与系统工程系，热那亚大学）
University of California, Santa Cruz（加州大学圣克鲁兹分校）；NASA Ames Dynamic Tensegrity Robotics Lab（NASA艾姆斯动力张拉整体机器人实验室）；NASA-ARC Advanced Studies Laboratories（NASA艾姆斯研究中心高级研究实验室）；Stinger Ghaffarian Technologies（Stinger Ghaffarian Technologies公司）
Most traditional robotic mechanisms feature inelastic joints that are unable to robustly handle large deformations and off-axis moments. As a result, the applied loads are transferred rigidly throughout the entire structure. The disadvantage of this approach is that the exerted leverage is magnified at each subsequent joint possibly damaging the mechanism. In this paper, we present two lightweight, elastic, bio-inspired tensegrity robotics arms which mitigate this danger while improving their mechanism's functionality. Our solutions feature modular tensegrity structures that function similarly…
Motion control of mobile manipulators (a robotic arm mounted on a mobile base) can be challenging for complex tasks such as material and package handling. In this paper, a task-space stabilization controller based on Nonlinear Model Predictive Control (NMPC) is designed and implemented to a 10 Degrees of Freedom (DOF) mobile manipulator which consists of a 7-DOF robotic arm and a 3-DOF mobile base. The system model is based on kinematic models where the end-effector orientation is parameterized directly by a rotation matrix. The state and control constraints as well as singularity constraints …
Robots are moving towards applications in less structured environments, but their model-based controllers are challenged by the tasks' complexity and intrinsic environmental unpredictability. Studying biological motor control can provide insights into overcoming these limitations due to the high dexterity and stability observable in humans and animals. This work presents a geometrical solution to the postural optimisation of 7-DoF limbs-like mechanisms, which are robust to singularities and computationally efficient. The theoretical formulation identified two separate decoupled optimisation st…
In the modern days, manipulators are found in the automated assembly lines of industries that produce products in masses. These manipulators can be used only in one configuration, that is either serial or parallel. In this paper, a new module which has two degrees of freedom is introduced. By connecting the two and three modules in series, 4 and 6 DoF hybrid manipulators can be formed respectively. By erecting 3 modules in parallel and with some minor modifications, a 6 DoF parallel manipulator can be formed. Hence the manipulator is reconfigurable and can be used as hybrid or parallel manipul…
Self-Adaptive Robust Motion Planning for High DoF Robot Manipulator using Deep MPC
University of Pittsburgh（匹兹堡大学）；University of Illinois Urbana-Champaign（伊利诺伊大学厄巴纳-香槟分校）；San Jose State University（圣何塞州立大学）；Snap Inc.（Snap公司）；George Washington University（乔治华盛顿大学）
Hussaini Adamu Polytechnic（侯赛因·阿达姆理工学院）；Bayero University, Kano（卡诺贝罗大学）；Ahmadu Bello University（阿赫马杜·贝洛大学）
Robot manipulators are extensively used in industrial applications because of their immense importance such as in constructions automation. Therefore, designing controllers to suit the intensive purpose of the application is one of the major challenges for control researchers. This paper presents comparative analysis of three controllers on a 3-DOF robot manipulator. The proportional integral derivative (PID), proportional derivative (PD) and fuzzy logic (FL) controllers were designed and applied to each of the link of the robot by simulation. The performance of each control method was assesse…
This paper discusses deriving geometric jacobians and identifying and analyzing the kinematic singularities for two 6 DOF arm robots. First we show the direct kinematics and D-H parameters derived for these two arms. The Geometric jacobian is computed for Barrett WAM and Smokie OUR. By analyzing the jacobian matrices we find the configurations at which J is rank deficient and derive the kinematic singularities through jacobian's determinent. Schematic are provided to show the singular configurations of both robots. Finally a survey is done on redundant kinematic allocation schemesfor 7 DoF Bar…
Indian Institute of Science（印度科学学院）；Robert Bosch Center for Cyber Physical Systems（罗伯特·博世网络物理系统中心）
In this paper, we present a novel passive single Degree-of-Freedom (DoF) manipulator design and its integration on an autonomous drone to capture a moving target. The end-effector is designed to be passive, to disengage the moving target from a flying UAV and capture it efficiently in the presence of disturbances, with minimal energy usage. It is also designed to handle target sway and the effect of downwash. The passive manipulator is integrated with the drone through a single Degree of Freedom (DoF) arm, and experiments are carried out in an outdoor environment. The rack-and-pinion mechanism…
Harbin Institute of Technology（哈尔滨工业大学）；University of California, Berkeley（加州大学伯克利分校）
The precise motion control of a multi-degree of freedom~(DOF) robot manipulator is always challenging due to its nonlinear dynamics, disturbances, and uncertainties. Because most manipulators are controlled by digital signals, a novel higher-order sliding mode controller in the discrete-time form with time delay estimation is proposed in this paper. The dynamic model of the manipulator used in the design allows proper handling of nonlinearities, uncertainties and disturbances involved in the problem. Specifically, parametric uncertainties and disturbances are handled by the time delay estimati…
Oregon State University（俄勒冈州立大学）；University of Massachusetts Amherst（马萨诸塞大学阿默斯特分校）；Olin College of Engineering（奥林工程学院）
We present a novel general model that unifies the kinematics of constant curvature and constant twist continuum manipulators. Combining this kinematics with energy-based physics, we derive a linear mapping from actuator configuration to manipulator deformation that is analogous to traditional robot forward kinematics. Our model generalizes across manipulators with different sizes, types of bending, and types of actuators, without the need for parameter re-fitting. The combination of generality and linearity makes the model useful for control and planning algorithms. Finally, our model is shown…
Quantum Machine Learning and Grover's Algorithm for Quantum Optimization of Robotic Manipulators
Robotics Research Center of Yuyao（余姚机器人研究中心）；Robotics Institute of Zhejiang University（浙江大学机器人研究所）；State Key Laboratory of Fluid Power and Mechatronic Systems（流体动力与机械电子系统国家重点实验室）；Institute of Design Engineering（设计工程院）；University of New Brunswick（新不伦瑞克大学）
Aerial robotic systems have raised emerging interests in recent years. In this article, we propose a novel aerial manipulator system that is significantly different from conventional aerial discrete manipulators: An Aerial Continuum Manipulator (AeCoM). The AeCoM compactly integrates a quadrotor with a tendon-driven continuum robotic manipulator. Due to the compact design and the payload bearing ability of tendon-driven continuum robotic arms, the proposed system solved the conflict between payload capacity and dexterity lying in conventional aerial manipulators. Two contributions are made in …
This work addresses the problem of kinematic trajectory planning for mobile manipulators with non-holonomic constraints, and holonomic operational-space tracking constraints. We obtain whole-body trajectories and time-varying kinematic feedback controllers by solving a Constrained Sequential Linear Quadratic Optimal Control problem. The employed algorithm features high efficiency through a continuous-time formulation that benefits from adaptive step-size integrators and through linear complexity in the number of integration steps. In a first application example, we solve kinematic trajectory p…
Predictive Kinematic Coordinate Control for Aerial Manipulators based on Modified Kinematics Learning
College of Computer Science and Technology, Zhejiang University（浙江大学计算机科学与技术学院）；Westlake University（西湖大学）；Westlake Institute for Optoelectronics（西湖光电研究院）
Laboratoire des Sciences du Numérique de Nantes（南特数字科学实验室）；Ecole Centrale Nantes（南特中央理工学院）；IMT Atlantique（IMT大西洋）；Innopolis University（因诺波利斯大学）；Centre National de la Recherche Scientifique (CNRS)（法国国家科学研究中心）
The paper focuses on the kinematics control of a compliant serial manipulator composed of a new type of dualtriangle elastic segments. Some useful optimization techniques were applied to solve the geometric redundancy problem, ensure the stability of the manipulator configurations with respect to the external forces/torques applied to the endeffector. The efficiency of the developed control algorisms is confirmed by simulation.
Optimal Control Approach for Non-prehensile Ball Juggling Using a 7-DoF Manipulator
Technical University of Munich（慕尼黑技术大学）；Mohamed Bin Zayed University of Artificial Intelligence（穆罕默德·本·扎耶德人工智能大学）；German Aerospace Center (DLR), Institute of Robotics and Mechatronics（德国航空航天中心（DLR）机器人与机电机构研究所）
Harbin Institute of Technology（哈尔滨工业大学）；University of Maryland at College Park（马里兰大学帕克分校）
We present a novel algorithm for collision-free kinematics of multiple manipulators in a shared workspace with moving obstacles. Our optimization-based approach simultaneously handles collision-free constraints based on reciprocal velocity obstacles and inverse kinematics constraints for high-DOF manipulators. We present an efficient method based on particle swarm optimization that can generate collision-free configurations for each redundant manipulator. Furthermore, our approach can be used to compute safe and oscillation-free trajectories in a few milli-seconds. We highlight the real-time p…
Indian Institute of Science（印度科学学院）；Robert Bosch Center for Cyber Physical Systems（罗伯特·博世信息物理系统研究中心）
Grabbing a manoeuvring target using drones is a challenging problem. This paper presents the design, development, and prototyping of a novel aerial manipulator for target interception. It is a single Degree of Freedom (DoF) manipulator with passive basket-type end-effector. The proposed design is energy efficient, light weight and suitable for aerial grabbing applications. The detailed design of the proposed manipulation mechanism and a novel in-flight extending propeller guard, is reported in this paper.
Australian Centre for Robotic Vision（澳大利亚机器人视觉中心）；Queensland University of Technology（昆士兰科技大学）
The elementary transform sequence (ETS) provides a universal method of describing the kinematics of any serial-link manipulator. The ETS notation is intuitive and easy to understand, while avoiding the complexity and limitations of Denvit-Hartenberg frame assignment. In this paper, we describe a systematic method for computing the manipulator Jacobian and Hessian (differential kinematics) using the ETS notation. Differential kinematics have many applications including numerical inverse kinematics, resolved-rate motion control and manipulability motion control. Furthermore, we provide an open-s…
This paper discusses modelling two 6 DOF arm robots. The first step of modelling a robot is establishing its Denavit-Hartenberg parameters. It requires assigning proper coordinates for each link and finding their exact dimensions. In this project we will develop the direct kinematics and workspace representations for two manipulators: the Smokie Robot and the Barrett WAM. After finding the D-H parameters and creating Transformation Matrices,MATLAB programming is used to represent their workspaces.
School of Artificial Intelligence and Automation, Huazhong University of Science and Technology（华中科技大学人工智能与自动化学院）；School of Automation, South East University（东南大学自动化学院）
The traditional kinematic calibration method for manipulators requires precise three-dimensional measuring instruments to measure the end pose, which is not only expensive due to the high cost of the measuring instruments but also not applicable to all manipulators. Another calibration method uses a camera, but the system error caused by the camera's parameters affects the calibration accuracy of the kinematics of the robot arm. Therefore, this paper proposes a method for calibrating the geometric parameters of a kinematic model of a manipulator based on monocular vision. Firstly, the classic …
Kinematics and Workspace Analysis of a Three-Axis Parallel Manipulator: the Orthoglide
Belarusian State University of Informatics and Radioelectronics（白俄罗斯信息与无线电电子大学）；Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
