arXiv 2210.044462022-10-10cs.RO

Dimensional synthesis of spatial manipulators for velocity and force transmission for operation around a specified task point

Indian Institute of Technology Kanpur（坎普尔印度理工学院）

Akkarapakam Suneesh Jacob, Bhaskar Dasgupta

英文摘要：

Dimensional synthesis refers to design of the dimensions of manipulators by optimising different kinds of performance indices. The motivation of this study is to perform dimensional synthesis for a wide set of spatial manipulators by optimising the manipulability of each manipulator around a pre-defined task point in the workspace and to finally give a prescription of manipulators along with their dimensions optimised for velocity and force transmission. A systematic method to formulate Jacobian matrix of a manipulator is presented. Optimisation of manipulability is performed for manipulation of the end-effector around a chosen task point for 96 1-DOF manipulators, 645 2-DOF manipulators, 8 3-DOF manipulators and 15 4-DOF manipulators taken from the result of enumeration of manipulators that is done in its companion paper devoted to enumeration of possible manipulators up to a number of links. Prescriptions for these sets of manipulators are presented along with their scaled condition numbers and their ordered indices. This gives the designer a prescription of manipulators with their optimised dimensions that reflects the performance of the end-effector around the given task point for velocity and force transmission.

机构、总结、中文摘要均由AI分析而来，可能存在错误，请以论文正文为准。

阅读原文

阅读 PDF ↗

arXiv 页面 ↗HTML 原文 ↗

本文内容

英文摘要相关论文

机构、总结、中文摘要均由AI分析而来，可能存在错误，请以论文正文为准。

继续探索

相关论文

利用邻接矩阵概念枚举空间机械臂

Enumeration of spatial manipulators by using the concept of Adjacency Matrix

Indian Institute of Technology Kanpur（印度坎普尔理工学院）；Capgemini Technology Services India Limited（凯捷技术服务印度有限公司）

本文提出利用邻接矩阵概念对含转动、移动、圆柱和球面关节的空间机械臂进行系统枚举，并给出多类自由度与连杆组合的具体数量结果。

2024-05-05cs.RO

基于PDE的多体柔顺机械臂动态建模的可扩展螺旋理论综合方法

Scalable Screw-Theoretic Synthesis for PDE-Based Dynamic Modeling of Multibody Flexible Manipulators

Tampere University（坦佩雷大学）；Johannes Kepler University Linz（林茨约翰·开普勒大学）

本文提出一种可扩展的螺旋理论多体综合框架，用于PDE基的串行机器人柔性连杆动态建模。通过构建螺旋理论PDE模型并严格施加约束力，实现了对局部和全局动态的捕捉。

2026-04-07cs.RO

基于主从式方法的协作物体运输研究

On the Collaborative Object Transportation Using Leader Follower Approach

TCS Research（塔塔咨询服务公司研究院）

针对部分已知障碍环境下的多智能体协作运输问题，提出结合比例导航导引与Stop-and-Sync算法的主从式方法，通过机械臂补偿非完整约束偏差，保持负载刚性，经对比验证了算法有效性。

2023-05-02cs.RO

Kinematic Synthesis of Parallel Manipulator via Neural Network Approach

University of Mazandaran（马赞达兰大学）

In this research, Artificial Neural Networks (ANNs) have been used as a powerful tool to solve the inverse kinematic equations of a parallel robot. For this purpose, we have developed the kinematic equations of a Tricept parallel kinematic mechanism with two rotational and one translational degrees of freedom (DoF). Using the analytical method, the inverse kinematic equations are solved for specific trajectory, and used as inputs for the applied ANNs. The results of both applied networks (Multi-Layer Perceptron and Redial Basis Function) satisfied the required performance in solving complex in…

2019-04-08cs.LGcs.ROstat.ML

Design Strategies for the Geometric Synthesis of Orthoglide-type Mechanisms

Belarusian State University of Informatics and Radioelectronics（白俄罗斯信息与无线电电子大学）；Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）；CNRS（法国国家科学研究中心）；École Centrale de Nantes（南特中央理工学院）；Université de Nantes（南特大学）；École des Mines de Nantes（南特矿业学院）

The paper addresses the geometric synthesis of Orthoglide-type mechanism, a family of 3-DOF parallel manipulators for rapid machining applications, which combine advantages of both serial mechanisms and parallel kinematic architectures. These manipulators possess quasi-isotropic kinematic performances and are made up of three actuated fixed prismatic joints, which are mutually orthogonal and connected to a mobile platform via three parallelogram chains. The platform moves in the Cartesian space with fixed orientation, similar to conventional XYZ-machine. Three strategies have been proposed to …

2007-08-28cs.RO

A Robust Force Control Approach for Underwater Vehicle Manipulator Systems

National Technical University of Athens（雅典国家技术大学）；KTH Royal Institute of Technology（瑞典皇家理工学院）

In various interaction tasks using Underwater Vehicle Manipulator Systems (UVMSs) (e.g. sampling of the sea organisms, underwater welding), important factors such as: i) uncertainties and complexity of UVMS dynamic model ii) external disturbances (e.g. sea currents and waves) iii) imperfection and noises of measuring sensors iv) steady state performance as well as v) inferior overshoot of interaction force error, should be addressed during the force control design. Motivated by the above factors, this paper presents a model-free control protocol for force controlling of an Underwater Vehicle M…

2017-04-04cs.RO

更多相关论文收起更多论文

串行机械臂的任务分布感知配重综合与约束协同设计

Task-Distribution-Aware Counterweight Synthesis and Constrained Co-Design for Serial Manipulators

College of Engineering and Information Technology, University of Dubai（迪拜大学工程与信息技术学院）

本文提出任务分布感知的配重综合框架，通过闭式最优解和仿射负载扩展，结合质量-半径约束协同设计，显著提升机械臂任务空间覆盖率。

2026-09-15cs.LGcs.RO

含外部扰动的机器人操作器无速度任务空间调节器

Velocity-free task-space regulator for robot manipulators with external disturbances

The Chinese University of Hong Kong（香港中文大学）；University of Groningen（格罗宁根大学）；South China University of Technology（华南理工大学）

针对受外部扰动的机器人操作器任务空间鲁棒调节问题，结合内模原理与无源性输出反馈控制提出无速度控制律，实现调节误差渐近收敛并抑制正弦扰动，具备简洁直观及直接增益选择准则的优势。

2025-04-14cs.ROcs.SYeess.SY

Set based velocity shaping for robotic manipulators

Queen’s University Belfast（贝尔法斯特女王大学）

We develop a new framework for trajectory planning on predefined paths, for general N-link manipulators. Different from previous approaches generating open-loop minimum time controllers or pre-tuned motion profiles by time-scaling, we establish analytic algorithms that recover all initial conditions that can be driven to the desirable target set while adhering to environment constraints. More technologically relevant, we characterise families of corresponding safe state-feedback controllers with several desirable properties. A key enabler in our framework is the introduction of a state feedbac…

2022-11-10cs.ROcs.SYeess.SY

通过空间图解指令教机器人去哪里以及如何行动：基于人类草图

Teaching Robots Where To Go And How To Act With Human Sketches via Spatial Diagrammatic Instructions

Robotics Institute, Carnegie Mellon University（卡内基梅隆大学机器人研究所）

本文提出空间图解指令方法，让操作员通过草图指定空间目标与约束，并学习空间指令图以优化移动机械臂基座放置，实现更高质量和更快速的求解。

2024-09-27cs.RO

Generating Continuous Motion and Force Plans in Real-Time for Legged Mobile Manipulation

University of Michigan（密歇根大学）；ETH Zürich（苏黎世联邦理工学院）

Manipulators can be added to legged robots, allowing them to interact with and change their environment. Legged mobile manipulation planners must consider how contact forces generated by these manipulators affect the system. Current planning strategies either treat these forces as immutable during planning or are unable to optimize over these contact forces while operating in real-time. This paper presents the Stability and Task Oriented Receding-Horizon Motion and Manipulation Autonomous Planner (STORMMAP) that is able to generate continuous plans for the robot's motion and manipulation force…

2021-04-23cs.RO

Motion and Force Planning for Manipulating Heavy Objects by Pivoting

Stony Brook University（石溪大学）

Manipulation of objects by exploiting their contact with the environment can enhance both the dexterity and payload capability of robotic manipulators. A common way to manipulate heavy objects beyond the payload capability of a robot is to use a sequence of pivoting motions, wherein, an object is moved while some contact points between the object and a support surface are kept fixed. The goal of this paper is to develop an algorithmic approach for automated plan generation for object manipulation with a sequence of pivoting motions. A plan for manipulating a heavy object consists of a sequence…

2021-04-25cs.RO

OWMM-Agent：基于多模态智能体数据合成的开放世界移动操作

OWMM-Agent: Open World Mobile Manipulation With Multi-modal Agentic Data Synthesis

Shanghai AI Laboratory（上海人工智能实验室）；School of Computing, National University of Singapore（新加坡国立大学计算机学院）；Shanghai Jiaotong University（上海交通大学）；Tsinghua University（清华大学）

针对开放世界移动操作任务，提出多模态智能体架构与数据合成流程，微调OWMM-VLM实现全局理解、状态跟踪和动作生成，达到SOTA性能并具零样本泛化能力。

2025-06-21cs.AIcs.RO

CSymPlan：面向高自由度机械臂的可验证符号规划与控制

CSymPlan: Certified Symbolic Planning and Control for High-DOF Manipulators

Mohamed bin Zayed University of Artificial Intelligence (MBZUAI)（穆罕默德·本·扎耶德人工智能大学（MBZUAI））；Technical University of Munich（慕尼黑工业大学）；Ludwig Maximilian University of Munich（慕尼黑大学）；New York University Abu Dhabi（纽约大学阿布扎比分校）

本文提出CSymPlan框架，通过离线预计算可验证策略与在线运行时循环，使高自由度机械臂完成可达-规避任务时零安全违规，无验证动作时安全处理。

2026-08-25cs.ROcs.SYeess.SY

用于4R和6R空间机构综合的有理运动计算机辅助设计

Computer-Aided Design of Rational Motions for 4R and 6R Spatial Mechanism Synthesis

Robotics Laboratory, Seoul National University（首尔国立大学机器人实验室）；Institute of Computer Science, Department of Mathematics and Informatics, Vilnius University（维尔纽斯大学计算机科学研究所）；Unit of Geometry and Surveying, University of Innsbruck（因斯布鲁克大学几何与测绘单位）；J. Radon Instit. for Computational and Applied Mathematics (RICAM), Austrian Academy of Sciences（奥地利科学院J.拉东研究所）

本文提出基于三次四元数贝塞尔曲线的七点插值方法，用于生成可分解为六杆机构的空间运动，支持工程实践中的快速视觉评估。

2026-02-24cs.RO

面向任意物体和机器人的接触合成通用机器人操作基础模型

ManiFoundation Model for General-Purpose Robotic Manipulation of Contact Synthesis with Arbitrary Objects and Robots

School of Electronics Engineering and Computer Science, Peking University（北京大学电子工程与计算机科学学院）；National University of Singapore（新加坡国立大学）；Shanghai Jiao Tong University（上海交通大学）

提出将机器人操作任务形式化为接触合成的基础模型，通过输入物体和机器人的点云及物理属性等，输出接触点和接触力，在多维度物体的仿真和真实实验中达到约90%成功率。

2024-09-25cs.AIcs.RO