The aim of this paper is to characterize the notion of aspect in the workspace and in the joint space for parallel manipulators. In opposite to the serial manipulators, the parallel manipulators can admit not only multiple inverse kinematic solutions, but also multiple direct kinematic solutions. The notion of aspect introduced for serial manipulators in [Borrel 86], and redefined for parallel manipulators with only one inverse kinematic solution in [Wenger 1997], is redefined for general fully parallel manipulators. Two Jacobian matrices appear in the kinematic relations between the joint-rate and the Cartesian-velocity vectors, which are called the "inverse kinematics" and the "direct kinematics" matrices. The study of these matrices allow to respectively define the parallel and the serial singularities. The notion of working modes is introduced to separate inverse kinematic solutions. Thus, we can find out domains of the workspace and the joint space exempt of singularity. Application of this study is the moveability analysis in the workspace of the manipulator as well as path-planing and control. This study is illustrated in this paper with a RR-RRR planar parallel manipulator.
École Centrale de Nantes（南特中央理工学院）；Université de Nantes（南特大学）
This work investigates new kinematic features of parallel manipulators. It is well known that parallel manipulators admit generally several direct kinematic solutions for a given set of input joint values. The aim of this paper is to characterize the uniqueness domains in the workspace of parallel manipulators, as well as their image in the joint space. The study focuses on the most usual case of parallel manipulators with only one inverse kinematic solution. The notion of aspect introduced for serial manipulators in [Borrel 86] is redefined for such parallel manipulators. Then, it is shown th…
Presented in this paper is the kinematic analysis of a symmetrical three-degree-of-freedom planar parallel manipulator. In opposite to serial manipulators, parallel manipulators can admit not only multiple inverse kinematic solutions, but also multiple direct kinematic solutions. This property produces more complicated kinematic models but allows more flexibility in trajectory planning. To take into account this property, the notion of aspects, i.e. the maximal singularity-free domains, was introduced, based on the notion of working modes, which makes it possible to separate the inverse kinema…
The aim of this paper is the kinematic study of a 3-RPR planar parallel manipulator where the three fixed revolute joints are actuated. The direct and inverse kinematic problem as well as the singular configuration is characterized. On parallel singular configurations, the motion produce by the mobile platform can be compared to the Reuleaux straight-line mechanism.
Institut de Recherche en Cybernétique de Nantes（南特控制论研究所）
The aim of this paper is to characterize the moveability of fully-parallel manipulators in the presence of obstacles. Fully parallel manipulators are used in applications where accuracy, stiffness or high speeds and accelerations are required \cite{Merlet:97}. However, one of its main drawbacks is a relatively small workspace compared to the one of serial manipulators. This is due mainly to the existence of potential internal collisions, and the existence of singularities. In this paper, the notion of free aspect is defined which permits to exhibit domains of the workspace and the joint space …
INRIA（法国国家信息与自动化研究所）；Institut de Recherche en Cybernétique de Nantes（南特控制论研究所）
The goal of this paper is to define the n-connected regions in the Cartesian workspace of fully-parallel manipulators, i.e. the maximal regions where it is possible to execute point-to-point motions. The manipulators considered in this study may have multiple direct and inverse kinematic solutions. The N-connected regions are characterized by projection, onto the Cartesian workspace, of the connected components of the reachable configuration space defined in the Cartesian product of the Cartesian space by the joint space. Generalized octree models are used for the construction of all spaces. T…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）；McGill University（麦吉尔大学）
The subject of this paper is a special class of parallel manipulators. First, we analyze a family of three-degree-of-freedom manipulators. Two Jacobian matrices appear in the kinematic relations between the joint-rate and the Cartesian-velocity vectors, which are called the "inverse kinematics" and the "direct kinematics" matrices. The singular configurations of these matrices are studied. The isotropic configurations are then studied based on the characteristic length of this manipulator. The isoconditioning loci of all Jacobian matrices are computed to define a global performance index to co…
A class of analytic planar 3-RPR manipulators is analyzed in this paper. These manipulators have congruent base and moving platforms and the moving platform is rotated of 180 deg about an axis in the plane. The forward kinematics is reduced to the solution of a 3rd-degree polynomial and a quadratic equation in sequence. The singularities are calculated and plotted in the joint space. The second-order singularities (cups points), which play an important role in non-singular change of assembly-mode motions, are also analyzed.
Arizona State University（亚利桑那州立大学）；Fulton Schools of Engineering（富尔顿工程学院）；The Polytechnic School（理工学院）
This paper evaluates how laminated techniques may be used to replicate the performance of more traditionally manufactured robotic manipulators. In this case study, we introduce a laminated 2-DOF spherical, parallel manipulator. Taking advantage of laminating techniques in the construction of the robot can result in considerable saving in construction costs and time, but, the challenges caused by this technique have to be addressed. By using stiffer materials in rigid links, the rigidity of the robot is increased to an acceptable level. We discuss one method for compensating position uncertaint…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
This paper investigates the singular curves in two-dimensional slices of the joint space of a family of planar parallel manipulators. It focuses on special points, referred to as cusp points, which may appear on these curves. Cusp points play an important role in the kinematic behavior of parallel manipulators since they make possible a nonsingular change of assembly mode. The purpose of this study is twofold. First, it reviews an important previous work, which, to the authors' knowledge, has never been exploited yet. Second, it determines the cusp points in any two-dimensional slice of the jo…
This paper investigates two situations in which the forward kinematics of planar 3-RPR parallel manipulators degenerates. These situations have not been addressed before. The first degeneracy arises when the three input joint variables r1, r2 and r3 satisfy a certain relationship. This degeneracy yields a double root of the characteristic polynomial in t, which could be erroneously interpreted as two coalesce assembly modes. But, unlike what arises in non-degenerate cases, this double root yields two sets of solutions for the position coordinates (x, y) of the platform. In the second situation…
It was shown recently that parallel manipulators with several inverse kinematic solutions have the ability to avoid parallel singularities [Chablat 1998a] and self-collisions [Chablat 1998b] by choosing appropriate joint configurations for the legs. In effect, depending on the joint configurations of the legs, a given configuration of the end-effector may or may not be free of singularity and collision. Characterization of the collision/singularity-free workspace is useful but may be insufficient since two configurations can be accessible without collisions nor singularities but it may not exi…
Indian Institute of Technology Ropar（印度理工学院鲁尔基分校（罗帕尔分校））
Modular and reconfigurable robotic systems have been designed to provide a customized solution for the non-repetitive tasks to be performed in a constrained environment. Customized solutions are normally extracted from task-based optimization of the possible manipulator configurations but the solution are not integrated, for providing the modular compositions directly. In this work, in the first phase, a strategy of finding unconventional optimal configurations with minimal number of degrees-of-freedom are discussed based upon the prescribed working locations and the cluttered environment. The…
Institut de Recherche en Cybernétique de Nantes（南特控制论研究所）
The goal of this paper is to explain, using a typical example, the distribution of the different assembly modes in the workspace and their effective role in the execution of trajectories. The singular and non-singular changes of assembly mode are described and compared to each other. The non-singular change of assembly mode is more deeply analysed and discussed in the context of trajectory planning. In particular, it is shown that, according to the location of the initial and final configurations with respect to the uniqueness domains in the workspace, there are three different cases to consid…
Parallel Transmission Aware Co-Design: Enhancing Manipulator Performance Through Actuation-Space Optimization
Robotics Innovation Center, DFKI GmbH（DFKI机器人创新中心）；Dynamics Division, Department of Mechanics & Maritime Sciences, Chalmers University of Technology（楚基姆斯理工大学机械与航海科学系动力分部）；AG Robotik, University of Bremen（不莱梅大学机器人技术研究所）
The direct kinematics analysis is the foundation of implementation of real world application of parallel manipulators. For most parallel manipulators the direct kinematics is challenging. In this paper, for the first time a fast and efficient Homotopy Continuation Method, called the Ostrowski Homotopy continuation method has been implemented to solve the direct and inverse kinematics problem of the parallel manipulators. This method has advantage over conventional numerical iteration methods, which is not rely on the initial values and is more efficient than other continuation method and it ca…
This paper presents a kinematic definition of a serialized Stewart platform designed for autonomous in-space assembly called an Assembler. The Assemblers architecture describes problems inherent to the inverse kinematics of over-actuated mixed kinematic systems. This paper also presents a methodology for optimizing poses. In order to accomplish this with the Assembler system, an algorithm for finding a feasible solution to its inverse kinematics was developed with a wrapper for a nonlinear optimization algorithm designed to minimize the magnitude of forces incurred by each actuator. A simulate…
Changzhou University（常州大学）；Nanjing Vocational Institute of Mechatronic Technology（南京机电职业技术学院）；Dalian University of Technology（大连理工大学）；Laboratoire des Sciences du Numérique de Nantes (LS2N)（南特数字科学实验室）
This paper presents a novel three-degree-of-freedom (3-DOF) translational parallel manipulator (TPM) by using a topological design method of parallel mechanism (PM) based on position and orientation characteristic (POC) equations. The proposed PM is only composed of lower-mobility joints and actuated prismatic joints, together with the investigations on three kinematic issues of importance. The first aspect pertains to geometric modeling of the TPM in connection with its topological characteristics, such as the POC, degree of freedom and coupling degree, from which its symbolic direct kinemati…
In this paper, a new numerical method to solve the forward kinematics (FK) of a parallel manipulator with three-limb spherical-prismatic-revolute (3SPR) structure is presented. Unlike the existing numerical approaches that rely on computation of the manipulator's Jacobian matrix and its inverse at each iteration, the proposed algorithm requires much less computations to estimate the FK parameters. A cost function is introduced that measures the difference of the estimates from the actual FK values. At each iteration, the problem is decomposed into two steps. First, the estimates of the platfor…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
This article provides a formalism making it possible to manage the solutions of the direct and inverse kinematic models of the fully parallel manipulators. We introduce the concept of working modes to separate the solutions from the opposite geometrical model. Then, we define, for each working mode, the aspects of these manipulators. To separate the solutions from the direct kinematics model, we introduce the concept of characteristic surfaces. Then, we define the uniqueness domains, as being the greatest domains of the workspace in which there is unicity of solutions. The principal applicatio…
In this research, Artificial Neural Networks (ANNs) have been used as a powerful tool to solve the inverse kinematic equations of a parallel robot. For this purpose, we have developed the kinematic equations of a Tricept parallel kinematic mechanism with two rotational and one translational degrees of freedom (DoF). Using the analytical method, the inverse kinematic equations are solved for specific trajectory, and used as inputs for the applied ANNs. The results of both applied networks (Multi-Layer Perceptron and Redial Basis Function) satisfied the required performance in solving complex in…
Laboratoire des Sciences du Numérique de Nantes（南特数字科学实验室）；École Polytéchnique de Montréal（蒙特利尔理工学院）
This paper presents the kinematic analysis of the 3-PPPS parallel robot with an equilateral mobile platform and a U-shape base. The proposed design and appropriate selection of parameters allow to formulate simpler direct and inverse kinematics for the manipulator under study. The parallel singularities associated with the manipulator depend only on the orientation of the end-effector, and thus depend only on the orientation of the end effector. The quaternion parameters are used to represent the aspects, i.e. the singularity free regions of the workspace. A cylindrical algebraic decomposition…
TopAY: Efficient Trajectory Planning for Differential Drive Mobile Manipulators via Topological Paths Search and Arc Length-Yaw Parameterization
State Key Laboratory of Industrial Control Technology, Zhejiang University, Hangzhou 310027, China（浙江大学工业控制技术状态重点实验室）；Huzhou Institute of Zhejiang University, Huzhou 313000, China（浙江大学湖州研究院）
We develop a new framework for trajectory planning on predefined paths, for general N-link manipulators. Different from previous approaches generating open-loop minimum time controllers or pre-tuned motion profiles by time-scaling, we establish analytic algorithms that recover all initial conditions that can be driven to the desirable target set while adhering to environment constraints. More technologically relevant, we characterise families of corresponding safe state-feedback controllers with several desirable properties. A key enabler in our framework is the introduction of a state feedbac…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
Recursive modelling for the kinematics of a 3-PRP planar parallel robot is presented in this paper. Three planar chains connecting to the moving platform of the manipulator are located in a vertical plane. Knowing the motion of the platform, we develop the inverse kinematics and determine the positions, velocities and accelerations of the robot. Several matrix equations offer iterative expressions and graphs for the displacements, velocities and accelerations of three prismatic actuators.
In the modern days, manipulators are found in the automated assembly lines of industries that produce products in masses. These manipulators can be used only in one configuration, that is either serial or parallel. In this paper, a new module which has two degrees of freedom is introduced. By connecting the two and three modules in series, 4 and 6 DoF hybrid manipulators can be formed respectively. By erecting 3 modules in parallel and with some minor modifications, a 6 DoF parallel manipulator can be formed. Hence the manipulator is reconfigurable and can be used as hybrid or parallel manipul…
This paper introduces a methodology to analyze geometrically the singularities of manipulators, of which legs apply both actuation forces and constraint moments to their moving platform. Lower-mobility parallel manipulators and parallel manipulators, of which some legs do not have any spherical joint, are such manipulators. The geometric conditions associated with the dependency of six Plücker vectors of finite lines or lines at infinity constituting the rows of the inverse Jacobian matrix are formulated using Grassmann-Cayley Algebra. Accordingly, the singularity conditions are obtained in ve…
Fast and Safe Trajectory Optimization for Mobile Manipulators With Neural Configuration Space Distance Field
Robotics and Autonomous Systems Thrust, The Hong Kong University of Science and Technology (Guangzhou)（香港科学与技术大学机器人与自主系统研究组）；Department of Electrical and Computer Engineering, National University of Singapore（新加坡国立大学电子与计算机工程系）；Idiap Research Institute（Idiap研究所）；Institute of Data Science, The University of Hong Kong（香港大学数据科学研究所）
University of Tartu（塔尔图大学）；Tampere University（坦佩雷大学）；Johannes Kepler University（约翰内斯·开普勒大学）
In this paper, we propose a novel trajectory optimization algorithm for mobile manipulators under end-effector path, collision avoidance and various kinematic constraints. Our key contribution lies in showing how this highly non-linear and non-convex problem can be solved as a sequence of convex unconstrained quadratic programs (QPs). This is achieved by reformulating the non-linear constraints that arise out of manipulator kinematics and its coupling with the mobile base in a multi-affine form. We then use techniques from Alternating Direction Method of Multipliers (ADMM) to formulate and sol…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
This paper investigates the singular curves in the joint space of a family of planar parallel manipulators. It focuses on special points, referred to as cusp points, which may appear on these curves. Cusp points play an important role in the kinematic behavior of parallel manipulators since they make possible a nonsingular change of assembly mode. The purpose of this study is twofold. First, it exposes a method to compute joint space singular curves of 3-RPR planar parallel manipulators. Second, it presents an algorithm for detecting and computing all cusp points in the joint space of these sa…
Institut de Recherche en Communications et en Cybernetique de Nantes（南特通信与控制论研究所）；Ecole des Mines de Nantes（南特国立高等矿业学校）
The paper presents a methodology to enhance the stiffness analysis of parallel manipulators with parallelogram-based linkage. It directly takes into account the influence of the external loading and allows computing both the non-linear ``load-deflection" relation and relevant rank-deficient stiffness matrix. An equivalent bar-type pseudo-rigid model is also proposed to describe the parallelogram stiffness by means of five mutually coupled virtual springs. The contributions of this paper are highlighted with a parallelogram-type linkage used in a manipulator from the Orthoglide family.
In this paper a new asymmetric 3-translational (3T) parallel manipulator, i.e., RPa(3R) 2R+RPa, with zero coupling degree and decoupled motion is firstly proposed according to topology design theory of parallel mechanism (PM) based on position and orientation characteristics (POC) equations. The main topological characteristics such as POC, degree of freedom and coupling degree are calculated. Then, the analytical formula for the direct and inverse kinematic are directly derived since coupling degree of the PM is zero. The study of singular configurations is simple because of the independence …
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制论研究所）
The subject of this paper is about the kinematic analysis and the trajectory planning of the Orthoglide 5-axis. The Orthoglide 5-axis a five degrees of freedom parallel kinematic machine developed at IRCCyN and is made up of a hybrid architecture, namely, a three degrees of freedom translational parallel manip-ulator mounted in series with a two degrees of freedom parallel spherical wrist. The simpler the kinematic modeling of the Or-thoglide 5-axis, the higher the maximum frequency of its control loop. Indeed, the control loop of a parallel kinematic machine should be computed with a high fre…
IRCCyN, Institut de recherche en communications et cybernéthique de Nantes（南特通信与控制研究所（IRCCyN））
In this paper, a method to compute joint space singularity surfaces of 3-RPR planar parallel manipulators is first presented. Then, a procedure to determine maximal joint space singularity-free boxes is introduced. Numerical examples are given in order to illustrate graphically the results. This study is of high interest for planning trajectories in the joint space of 3-RPR parallel manipulators and for manipulators design as it may constitute a tool for choosing appropriate joint limits and thus for sizing the link lengths of the manipulator.
Institut de Recherche en Cybernétique de Nantes（南特控制论研究所）；École Centrale de Nantes（南特中央理工学院）；Université de Nantes（南特大学）
The aim of this paper is to characterize the uniqueness domains in the workspace of parallel manipulators, as well as their image in the joint space. The notion of aspect introduced for serial manipulators in [Borrel 86] is redefined for such parallel manipulators. Then, it is shown that it is possible to link several solutions to the direct kinematic problem without meeting a singularity, thus meaning that the aspects are not uniqueness domains. Additional surfaces are characterized in the workspace which yield new uniqueness domains. An octree model of spaces is used to compute the joint spa…
Institut de Recherche en Communication et Cybernétique de Nantes（南特通信与控制研究所）
This paper characterizes geometrically the singularities of limited DOF parallel manipulators. The geometric conditions associated with the dependency of six Plücker vector of lines (finite and infinite) constituting the rows of the inverse Jacobian matrix are formulated using Grassmann-Cayley algebra. Manipulators under consideration do not need to have a passive spherical joint somewhere in each leg. This study is illustrated with three example robots
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
This paper presents an algorithm for detecting and computing the cusp points in the joint space of 3-RPR planar parallel manipulators. In manipulator kinematics, cusp points are special points, which appear on the singular curves of the manipulators. The nonsingular change of assembly mode of 3-RPR parallel manipulators was shown to be associated with the existence of cusp points. At each of these points, three direct kinematic solutions coincide. In the literature, a condition for the existence of three coincident direct kinematic solutions was established, but has never been exploited, becau…
Institut de Recherches en Communications et Cybernétique de Nantes（南特通信与控制研究所）；Ecole des Mines de Nantes（南特矿业学院）
The paper presents a new stiffness modeling method for overconstrained parallel manipulators with flexible links and compliant actuating joints. It is based on a multidimensional lumped-parameter model that replaces the link flexibility by localized 6-dof virtual springs that describe both translational/rotational compliance and the coupling between them. In contrast to other works, the method involves a FEA-based link stiffness evaluation and employs a new solution strategy of the kinetostatic equations for the unloaded manipulator configuration, which allows computing the stiffness matrix fo…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）；CNRS（法国国家科学研究中心）
This paper deals with the comparison of planar parallel manipulator architectures based on a multi-objective design optimization approach. The manipulator architectures are compared with regard to their mass in motion and their regular workspace size, i.e., the objective functions. The optimization problem is subject to constraints on the manipulator dexterity and stiffness. For a given external wrench, the displacements of the moving platform have to be smaller than given values throughout the obtained maximum regular dexterous workspace. The contributions of the paper are highlighted with th…
This paper deals with the in-depth kinematic analysis of a special spherical parallel wrist, called the Agile Eye. The Agile Eye is a three-legged spherical parallel robot with revolute joints in which all pairs of adjacent joint axes are orthogonal. Its most peculiar feature, demonstrated in this paper for the first time, is that its (orientation) workspace is unlimited and flawed only by six singularity curves (rather than surfaces). Furthermore, these curves correspond to self-motions of the mobile platform. This paper also demonstrates that, unlike for any other such complex spatial robots…
The paper focuses on the stiffness modeling of parallel manipulators composed of non-perfect serial chains, whose geometrical parameters differ from the nominal ones. In these manipulators, there usually exist essential internal forces/torques that considerably affect the stiffness properties and also change the end-effector location. These internal load-ings are caused by elastic deformations of the manipulator ele-ments during assembling, while the geometrical errors in the chains are compensated for by applying appropriate forces. For this type of manipulators, a non-linear stiffness modeli…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）；McGill University（麦吉尔大学）
The subject of this paper is a special class of three-degree-of-freedom parallel manipulators. The singular configurations of the two Jacobian matrices are first studied. The isotropic configurations are then found based on the characteristic length of this manipulator. The isoconditioning loci for the Jacobian matrices are plotted to define a global performance index allowing the comparison of the different working modes. The index thus resulting is compared with the Cartesian workspace surface and the average of the condition number.
Institut de Recherche en Communications et Cybernetique de Nantes（南特通信与控制论研究所）；Ecole des Mines de Nantes（南特国立高等矿业学校）；University of Agder（阿格德大学）
The paper is devoted to the compliance errors compensation for parallel manipulators under external loading. Proposed approach is based on the non-linear stiffness modeling and reduces to a proper adjusting of a target trajectory. In contrast to previous works, in addition to compliance errors caused by machining forces, the problem of assembling errors caused by inaccuracy in the kinematic chains is considered. The advantages and practical significance of the proposed approach are illustrated by examples that deal with groove milling with Orthoglide manipulator.
This paper investigates the existence conditions of cusp points in the design parameter space of the R\underline{P}R-2P\underline{R}R parallel manipulators. Cusp points make possible non-singular assembly-mode changing motion, which can possibly increase the size of the aspect, i.e. the maximum singularity free workspace. The method used is based on the notion of discriminant varieties and Cylindrical Algebraic Decomposition, and resorts to Gröbner bases for the solutions of systems of equations.
Ecole des Mines de Nantes（南特高等矿业学院）；Institut de Recherches en Communications et Cybernétique de Nantes（南特通信与控制研究所）
The paper proposes an integrated approach to the design optimization of parallel manipulators, which is based on the concept of the workspace grid and utilizes the goal-attainment formulation for the global optimization. To combine the non-homogenous design specification, the developed optimization technique transforms all constraints and objectives into similar performance indices related to the maximum size of the prescribed shape workspace. This transformation is based on the dedicated dynamic programming procedures that satisfy computational requirements of modern CAD. Efficiency of the de…
Laboratoire d’informatique de Paris（巴黎信息学实验室）；Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制论研究所）
This paper investigates the cuspidal configurations of 3-RPR parallel manipulators that may appear on their singular surfaces in the joint space. Cusp points play an important role in the kinematic behavior of parallel manipulators since they make possible a non-singular change of assembly mode. In previous works, the cusp points were calculated in sections of the joint space by solving a 24th-degree polynomial without any proof that this polynomial was the only one that gives all solutions. The purpose of this study is to propose a rigorous methodology to determine the cusp points of 3-R\unde…
