This paper investigates the cuspidal configurations of 3-RPR parallel manipulators that may appear on their singular surfaces in the joint space. Cusp points play an important role in the kinematic behavior of parallel manipulators since they make possible a non-singular change of assembly mode. In previous works, the cusp points were calculated in sections of the joint space by solving a 24th-degree polynomial without any proof that this polynomial was the only one that gives all solutions. The purpose of this study is to propose a rigorous methodology to determine the cusp points of 3-R\underline{P}R manipulators and to certify that all cusp points are found. This methodology uses the notion of discriminant varieties and resorts to Gröbner bases for the solutions of systems of equations.
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
This paper investigates the singular curves in the joint space of a family of planar parallel manipulators. It focuses on special points, referred to as cusp points, which may appear on these curves. Cusp points play an important role in the kinematic behavior of parallel manipulators since they make possible a nonsingular change of assembly mode. The purpose of this study is twofold. First, it exposes a method to compute joint space singular curves of 3-RPR planar parallel manipulators. Second, it presents an algorithm for detecting and computing all cusp points in the joint space of these sa…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
This paper presents an algorithm for detecting and computing the cusp points in the joint space of 3-RPR planar parallel manipulators. In manipulator kinematics, cusp points are special points, which appear on the singular curves of the manipulators. The nonsingular change of assembly mode of 3-RPR parallel manipulators was shown to be associated with the existence of cusp points. At each of these points, three direct kinematic solutions coincide. In the literature, a condition for the existence of three coincident direct kinematic solutions was established, but has never been exploited, becau…
This paper investigates the existence conditions of cusp points in the design parameter space of the R\underline{P}R-2P\underline{R}R parallel manipulators. Cusp points make possible non-singular assembly-mode changing motion, which can possibly increase the size of the aspect, i.e. the maximum singularity free workspace. The method used is based on the notion of discriminant varieties and Cylindrical Algebraic Decomposition, and resorts to Gröbner bases for the solutions of systems of equations.
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
This paper investigates the singular curves in two-dimensional slices of the joint space of a family of planar parallel manipulators. It focuses on special points, referred to as cusp points, which may appear on these curves. Cusp points play an important role in the kinematic behavior of parallel manipulators since they make possible a nonsingular change of assembly mode. The purpose of this study is twofold. First, it reviews an important previous work, which, to the authors' knowledge, has never been exploited yet. Second, it determines the cusp points in any two-dimensional slice of the jo…
L'Institut de Recherche en Communications et Cybernétique de Nantes (IRCCyN), École Central de Nantes（南特通信与控制研究所，南特中央学院）
Cusps and nodes on plane sections of the singularity locus in the joint space of parallel manipulators play an important role in nonsingular assembly-mode changing motions. This paper analyses in detail such points, both in the joint space and in the workspace. It is shown that a cusp (resp. a node) defines a point of tangency (resp. a crossing point) in the workspace between the singular curves and the curves associated with the so-called characteristics surfaces. The study is conducted on a planar 3-RPR manipulator for illustrative purposes.
Institut de Robòtica i Informàtica Industrial, CSIC - UPC（工业机器人与信息学研究所，西班牙国家研究委员会-加泰罗尼亚理工大学）；INRIA Nancy-Grand Est（法国国家信息与自动化研究所南锡-大东部研究中心）；Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制论研究所）；INRIA Paris-Rocquencourt（法国国家信息与自动化研究所巴黎-罗克库尔研究中心）；Université Pierre et Marie Curie Paris VI（巴黎第六大学皮埃尔和玛丽·居里大学）
This paper investigates the conditions in the design parameter space for the existence and distribution of the cusp locus for planar parallel manipulators. Cusp points make possible non-singular assembly-mode changing motion, which increases the maximum singularity-free workspace. An accurate algorithm for the determination is proposed amending some imprecisions done by previous existing algorithms. This is combined with methods of Cylindric Algebraic Decomposition, Gröbner bases and Discriminant Varieties in order to partition the parameter space into cells with constant number of cusp points…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
The aim of this paper is to classify one family of 3R serial positioning manipulators. This categorization is based on the number of cusp points of quaternary, binary, generic and non-generic manipulators. It was found three subsets of manipulators with 0, 2 or 4 cusp points and one homotopy class for generic quaternary manipulators. This classification allows us to define the design parameters for which the manipulator is cuspidal or not, i.e., for which the manipulator can or cannot change posture without meeting a singularity, respectively.
Institut de Recherche Mathématique de Rennes（雷恩数学研究所）；Université de Rennes I（雷恩第一大学）；Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
We study in this paper a class of 3-RPR manipulators for which the direct kinematic problem (DKP) is split into a cubic problem followed by a quadratic one. These manipulators are geometrically characterized by the fact that the moving triangle is the image of the base triangle by an indirect isometry. We introduce a specific coordinate system adapted to this geometric feature and which is also well adapted to the splitting of the DKP. This allows us to obtain easily precise descriptions of the singularities and of the cusp edges. These latter second order singularities are important for nonsi…
Nantes Université（南特大学）；École Centrale Nantes（南特中央理工学院）；CNRS（法国国家科学研究中心）
Cuspidal robots can move from one inverse or direct kinematic solution to another without ever passing through a singularity. These robots have remained unknown because almost all industrial robots do not have this feature. However, in fact, industrial robots are the exceptions. Some robots appeared recently in the industrial market can be shown to be cuspidal but, surprisingly, almost nobody knows it and robot users meet difficulties in planning trajectories with these robots. This paper proposes a review on the fundamental and application aspects of cuspidal robots. It addresses the importan…
Laboratoire des Sciences du Numérique de Nantes（南特数字科学实验室）；University of Innsbruck（因斯布鲁克大学）
Cuspidal robots can travel from one inverse kinematic solution to another without meeting a singularity. The name cuspidal was coined based on the existence of a cusp point in the workspace of 3R serial robots. The existence of a cusp point was proved to be a necessary and sufficient condition for orthogonal robots to be cuspidal, but it was not possible to extend this condition to non-orthogonal robots. The goal of this paper is to prove that this condition stands for any generic 3R robot. This result would give the designer more flexibility. In the presented work, the geometrical interpretat…
École de technologie supérieure（高等技术学院）；Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制论研究所）
This paper demonstrates that any general 3-DOF three-legged planar parallel robot with extensible legs can change assembly modes without passing through parallel singularities (configurations where the mobile platform loses its stiffness). While the results are purely theoretical, this paper questions the very definition of parallel singularities.
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
The workspace topologies of a family of 3-revolute (3R) positioning manipulators are enumerated. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps that appear on these singular curves. The design parameters space is shown to be divided into five domains where all manipulators have the same number of cusps. Each separating surface is given as an explicit expression in the DH-parameters. As an application of this work, we provide a necessary and sufficient condition for a 3R orthogonal manipulator to be cuspida…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）
A classification of a family of 3-revolute (3R) positioning manipulators is established. This classification is based on the topology of their workspace. The workspace is characterized in a half-cross section by the singular curves of the manipulator. The workspace topology is defined by the number of cusps and nodes that appear on these singular curves. The design parameters space is shown to be partitioned into nine subspaces of distinct workspace topologies. Each separating surface is given as an explicit expression in the DH-parameters.
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与网络研究所）
A classification of a family of 3-revolute (3R) positining manipulators is established. This classification is based on the topology of their workspace. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps and nodes that appear on these singular curves. The design parameters space is shown to be divided into nine domains of distinct workspace topologies, in which all manipulators have similar global kinematic properties. Each separating surface is given as an explicit expression in the DH-parameters.
Cuspidal robots are robots with at least two inverse kinematic solutions that can be connected by a singularity-free path. Deciding the cuspidality of generic 3R robots has been studied in the past, but extending the study to six-degree-of-freedom robots can be a challenging problem. Many robots can be modeled as a polynomial map together with a real algebraic set so that the notion of cuspidality can be extended to these data. In this paper we design an algorithm that, on input a polynomial map in $n$ indeterminates, and $s$ polynomials in the same indeterminates describing a real algebraic s…
IRCCyN, Institut de Recherche en Communications et Cybernetique de Nantes（南特通信与控制研究所（IRCCyN））；McGill University（麦吉尔大学）
This paper proposes a classification of three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. This classification is based on the topology of their workspace. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps and nodes that appear on these singular curves. The manipulators are classified into different types with similar kinematic properties. Each type is evaluated according to interesting kinematic properties such as, whether the workspace is fully reachable with…
IRMAR, Université de Rennes 1 – CNRS（法国国家科学研究中心、雷恩第一大学数学研究所（IRMAR））；IRCCyN, CNRS – École Centrale de Nantes（法国国家科学研究中心、南特中央理工学院南特通信与控制研究所（IRCCyN））
This paper investigates a situation pointed out in a recent paper, in which a non-singular change of assembly mode of a planar 2-RPR-PR parallel manipulator was realized by encircling a point of multiplicity 4. It is shown that this situation is, in fact, a non-generic one and gives rise to cusps under a small perturbation. Furthermore , we show that, for a large class of singularities of multiplicity 4, there are only two types of stable singularities occurring in a small perturbation: these two types are given by the complex square mapping and the quarto mapping. Incidentally , this paper co…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）；CNRS（法国国家科学研究中心）
A family of 3R orthogonal manipulators without offset on the third body can be divided into exactly nine workspace topologies. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps and nodes that appear on these singular curves. Based on this classification, we evaluate theses manipulators by the condition number related to the joint space and the proportion of the region with four inverse kinematic solutions compared to a sphere containing all the workspace. This second performance number is in relation with the…
