Positioning 3R manipulators may have two or four inverse kinematic solutions (IKS). This paper derives a necessary and sufficient condition for 3R positioning manipulators with orthogonal joint axes to have four distinct IKS. We show that the transition between manipulators with 2 and 4 IKS is defined by the set of manipulators with a quadruple root of their inverse kinematics. The resulting condition is explicit and states that the last link length of the manipulator must be greater than a quantity that depends on three of its remaining DH-parameters. This result is of interest for the design of new manipulators.
Presented in this paper is the kinematic analysis of a symmetrical three-degree-of-freedom planar parallel manipulator. In opposite to serial manipulators, parallel manipulators can admit not only multiple inverse kinematic solutions, but also multiple direct kinematic solutions. This property produces more complicated kinematic models but allows more flexibility in trajectory planning. To take into account this property, the notion of aspects, i.e. the maximal singularity-free domains, was introduced, based on the notion of working modes, which makes it possible to separate the inverse kinema…
Oregon State University（俄勒冈州立大学）；University of Massachusetts Amherst（马萨诸塞大学阿默斯特分校）；Olin College of Engineering（奥林工程学院）
We present a novel general model that unifies the kinematics of constant curvature and constant twist continuum manipulators. Combining this kinematics with energy-based physics, we derive a linear mapping from actuator configuration to manipulator deformation that is analogous to traditional robot forward kinematics. Our model generalizes across manipulators with different sizes, types of bending, and types of actuators, without the need for parameter re-fitting. The combination of generality and linearity makes the model useful for control and planning algorithms. Finally, our model is shown…
The aim of this paper is the kinematic study of a 3-RPR planar parallel manipulator where the three fixed revolute joints are actuated. The direct and inverse kinematic problem as well as the singular configuration is characterized. On parallel singular configurations, the motion produce by the mobile platform can be compared to the Reuleaux straight-line mechanism.
Institut de Recherche en Cybernétique de Nantes（南特控制论研究所）；École Centrale de Nantes（南特中央理工学院）
The aim of this paper is to characterize the notion of aspect in the workspace and in the joint space for parallel manipulators. In opposite to the serial manipulators, the parallel manipulators can admit not only multiple inverse kinematic solutions, but also multiple direct kinematic solutions. The notion of aspect introduced for serial manipulators in [Borrel 86], and redefined for parallel manipulators with only one inverse kinematic solution in [Wenger 1997], is redefined for general fully parallel manipulators. Two Jacobian matrices appear in the kinematic relations between the joint-rat…
A class of analytic planar 3-RPR manipulators is analyzed in this paper. These manipulators have congruent base and moving platforms and the moving platform is rotated of 180 deg about an axis in the plane. The forward kinematics is reduced to the solution of a 3rd-degree polynomial and a quadratic equation in sequence. The singularities are calculated and plotted in the joint space. The second-order singularities (cups points), which play an important role in non-singular change of assembly-mode motions, are also analyzed.
This work addresses the problem of kinematic trajectory planning for mobile manipulators with non-holonomic constraints, and holonomic operational-space tracking constraints. We obtain whole-body trajectories and time-varying kinematic feedback controllers by solving a Constrained Sequential Linear Quadratic Optimal Control problem. The employed algorithm features high efficiency through a continuous-time formulation that benefits from adaptive step-size integrators and through linear complexity in the number of integration steps. In a first application example, we solve kinematic trajectory p…
Institut de recherche en communications et cybernétique de Nantes（南特通信与控制研究所）；CNRS（法国国家科学研究中心）
This paper proposes a method to calculate the largest Regular Dextrous Workspace (RDW) of some types of three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. Then a new performance index based on the RDW is introduced, the isocontours of this index are plotted in the parameter space of the interesting types of manipulators and finally an inspection of the domains of the parameter spaces is conducted in order to identify the better manipulator architectures. The RDW is a part of the workspace whose shape is regular (cube, cylinder) and the performan…
This paper analyses the workspace of the three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. These manipulators are classified into different groups with similar kinematic properties. The classification criteria are based on the topology of the workspace. Each group is evaluated according to interesting kinematic properties such as the size of the workspace subregion reachable with four inverse kinematic solutions, the existence and the size of voids, and the size of the regions of feasible paths in the workspace.
Predictive Kinematic Coordinate Control for Aerial Manipulators based on Modified Kinematics Learning
College of Computer Science and Technology, Zhejiang University（浙江大学计算机科学与技术学院）；Westlake University（西湖大学）；Westlake Institute for Optoelectronics（西湖光电研究院）
This paper investigates two situations in which the forward kinematics of planar 3-RPR parallel manipulators degenerates. These situations have not been addressed before. The first degeneracy arises when the three input joint variables r1, r2 and r3 satisfy a certain relationship. This degeneracy yields a double root of the characteristic polynomial in t, which could be erroneously interpreted as two coalesce assembly modes. But, unlike what arises in non-degenerate cases, this double root yields two sets of solutions for the position coordinates (x, y) of the platform. In the second situation…
Australian Centre for Robotic Vision（澳大利亚机器人视觉中心）；Queensland University of Technology（昆士兰科技大学）
The elementary transform sequence (ETS) provides a universal method of describing the kinematics of any serial-link manipulator. The ETS notation is intuitive and easy to understand, while avoiding the complexity and limitations of Denvit-Hartenberg frame assignment. In this paper, we describe a systematic method for computing the manipulator Jacobian and Hessian (differential kinematics) using the ETS notation. Differential kinematics have many applications including numerical inverse kinematics, resolved-rate motion control and manipulability motion control. Furthermore, we provide an open-s…
IRCCyN, Institut de Recherche en Communications et Cybernetique de Nantes（南特通信与控制研究所（IRCCyN））；McGill University（麦吉尔大学）
This paper proposes a classification of three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. This classification is based on the topology of their workspace. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps and nodes that appear on these singular curves. The manipulators are classified into different types with similar kinematic properties. Each type is evaluated according to interesting kinematic properties such as, whether the workspace is fully reachable with…
École Centrale de Nantes（南特中央理工学院）；Université de Nantes（南特大学）
This work investigates new kinematic features of parallel manipulators. It is well known that parallel manipulators admit generally several direct kinematic solutions for a given set of input joint values. The aim of this paper is to characterize the uniqueness domains in the workspace of parallel manipulators, as well as their image in the joint space. The study focuses on the most usual case of parallel manipulators with only one inverse kinematic solution. The notion of aspect introduced for serial manipulators in [Borrel 86] is redefined for such parallel manipulators. Then, it is shown th…
IMT Atlantique Bretagne Pays de la Loire（大西洋布列塔尼卢瓦尔河国家高等矿业电信学校）；Centre National de la Recherche Scientifique (CNRS)（法国国家科学研究中心）
The paper focuses on the redundancy resolution in kinematic control of a new type of serial manipulator composed of multiple tensegrity segments, which are moving in a multi-obstacle environment. The general problem is decomposed into two sub-problems, which deal with collision-free path planning for the robot end-effector and collision-free motion planning for the robot body. The first of them is solved via discrete dynamic programming, the second one is worked out using quadratic programming with mixed linear equality/nonequality constraints. Efficiency of the proposed technique is confirmed…
Institut de Recherche en Communications et Cybernétique de Nantes（南特通信与控制研究所）；McGill University（麦吉尔大学）
The subject of this paper is a special class of parallel manipulators. First, we analyze a family of three-degree-of-freedom manipulators. Two Jacobian matrices appear in the kinematic relations between the joint-rate and the Cartesian-velocity vectors, which are called the "inverse kinematics" and the "direct kinematics" matrices. The singular configurations of these matrices are studied. The isotropic configurations are then studied based on the characteristic length of this manipulator. The isoconditioning loci of all Jacobian matrices are computed to define a global performance index to co…
Computer Science and Engineering Department, University of South Carolina（南卡罗来纳大学计算机科学与工程系）；Department of Mechanical Engineering, National Technical University of Athens（雅典国立技术大学机械工程系）
A hyper-redundant robotic arm is a manipulator with many degrees of freedom, capable of executing tasks in cluttered environments where robotic arms with fewer degrees of freedom are unable to operate. This paper introduces a new method for modeling those manipulators in a completely dynamic way. The proposed method enables online changes of the kinematic structure with the use of a special function; termed "meta-controlling function". This function can be used to develop policies to reduce drastically the computational cost for a single task, and to robustly control the robotic arm, even in t…
A polynomial solution to the inverse kinematic problem of the Kinova Gen3 Lite robot is proposed in this paper. This serial robot is based on a 6R kinematic chain and is not wrist-partitioned. We first start from the forward kinematics equation providing the position and orientation of the end-effector, finally, the univariate polynomial equation is given as a function of the first joint variable $θ_{1}$. The remaining joint variables are computed by back substitution. Thus, an unique set of joint position is obtain for each root of the univariate equation. Numerical examples, simulated in ROS…
Institut de Recherche en Cybernétique de Nantes（南特控制论研究所）；École Centrale de Nantes（南特中央理工学院）；McGill University（麦吉尔大学）
The subject of this paper is a special class of closed-chain manipulators. First, we analyze a family of two-degree-of-freedom (dof) five-bar planar linkages. Two Jacobian matrices appear in the kinematic relations between the joint-rate and the Cartesian-velocity vectors, which are called the ``inverse kinematics" and the "direct kinematics" matrices. It is shown that the loci of points of the workspace where the condition number of the direct-kinematics matrix remains constant, i.e., the isoconditioning loci, are the coupler points of the four-bar linkage obtained upon locking the middle joi…
Multimodal Control of Manipulators: Coupling Kinematics and Vision for Self-Driving Laboratory Operations
1 Department of Electronics Systems, Aalborg University, Denmark；3 Extreme Robotics Laboratory, School of Metallurgy \& Materials, University of Birmingham, Birmingham, United Kingdom
Harbin Institute of Technology（哈尔滨工业大学）；University of Maryland at College Park（马里兰大学帕克分校）
We present a novel algorithm for collision-free kinematics of multiple manipulators in a shared workspace with moving obstacles. Our optimization-based approach simultaneously handles collision-free constraints based on reciprocal velocity obstacles and inverse kinematics constraints for high-DOF manipulators. We present an efficient method based on particle swarm optimization that can generate collision-free configurations for each redundant manipulator. Furthermore, our approach can be used to compute safe and oscillation-free trajectories in a few milli-seconds. We highlight the real-time p…
Egypt-Japan University of Science and Technology（埃及-日本科学技术大学）
This paper presents the inverse kinematic analysis and parameters identification of a novel aerial manipulation system. This system consists of 2-link manipulator attached to the bottom of a quadrotor. This new system presents a solution for the limitations found in the current quadrotor manipulation system. By deriving the inverse kinematics, one can design the controller such that the desired end effector position and orientation can be tracked. To study the feasibility of the proposed system, a quadrotor with high enough payload to add the 2-link manipulator is designed and constructed. Exp…
The direct kinematics analysis is the foundation of implementation of real world application of parallel manipulators. For most parallel manipulators the direct kinematics is challenging. In this paper, for the first time a fast and efficient Homotopy Continuation Method, called the Ostrowski Homotopy continuation method has been implemented to solve the direct and inverse kinematics problem of the parallel manipulators. This method has advantage over conventional numerical iteration methods, which is not rely on the initial values and is more efficient than other continuation method and it ca…
Research Institute for Symbolic Computation, Johannes Kepler University（约翰内斯·开普勒大学符号计算研究所）；University of the Philippines Diliman（菲律宾大学迪里曼分校）
We develop an algorithm that solves the inverse kinematics of general serial 2RP3R, 2R2P2R, 3RP2R and 6R manipulators based on the HuPf algorithm. We identify the workspaces of the 3-subchains of the manipulator with a quasi-projective variety in $\mathbb{P}^7$ via dual quaternions. This allows us to compute linear forms that describe linear spaces containing the workspaces of these 3-subchains. We present numerical examples that illustrate the algorithm and show the real solutions.
Changzhou University（常州大学）；Nanjing Vocational Institute of Mechatronic Technology（南京机电职业技术学院）；Dalian University of Technology（大连理工大学）；Laboratoire des Sciences du Numérique de Nantes (LS2N)（南特数字科学实验室）
This paper presents a novel three-degree-of-freedom (3-DOF) translational parallel manipulator (TPM) by using a topological design method of parallel mechanism (PM) based on position and orientation characteristic (POC) equations. The proposed PM is only composed of lower-mobility joints and actuated prismatic joints, together with the investigations on three kinematic issues of importance. The first aspect pertains to geometric modeling of the TPM in connection with its topological characteristics, such as the POC, degree of freedom and coupling degree, from which its symbolic direct kinemati…
TU Wien（维也纳工业大学）；University of Liverpool（利物浦大学）；Austrian Institute of Technology GmbH (AIT)（奥地利技术研究院有限公司）
Solving the analytical inverse kinematics (IK) of redundant manipulators in real time is a difficult problem in robotics since its solution for a given target pose is not unique. Moreover, choosing the optimal IK solution with respect to application-specific demands helps to improve the robustness and to increase the success rate when driving the manipulator from its current configuration towards a desired pose. This is necessary, especially in high-dynamic tasks like catching objects in mid-flights. To compute a suitable target configuration in the joint space for a given target pose in the t…
This paper presents a kinematic definition of a serialized Stewart platform designed for autonomous in-space assembly called an Assembler. The Assemblers architecture describes problems inherent to the inverse kinematics of over-actuated mixed kinematic systems. This paper also presents a methodology for optimizing poses. In order to accomplish this with the Assembler system, an algorithm for finding a feasible solution to its inverse kinematics was developed with a wrapper for a nonlinear optimization algorithm designed to minimize the magnitude of forces incurred by each actuator. A simulate…
Considering the difficulty of students in calculating the direct and inverse kinematics of a robotic manipulator using only conventional tools of a classroom, this article proposes the application of Project Based Learning (ABP) through the design, development, mathematical modeling of a robotic manipulator as an integrative project of the disciplines of Industrial Robotics, Microcontrollers and Computer Assisted Design with students of the Control and Automation Engineering of the University of Fortaleza. Once designed and machined, the manipulator arm was assembled using servo motors connect…
University of Bengkulu（明古鲁大学）；Pusat Penelitian Elektronika dan Telekomunikasi Lembaga Ilmu Pengetahuan Indonesia（印度尼西亚科学院电子学与电信研究中心）
This paper presents the development of vision-based robotic arm manipulator control by applying Proportional Derivative-Pseudoinverse Jacobian (PD-PIJ) kinematics and Denavit Hartenberg forward kinematics. The task of sorting objects based on color is carried out to observe error propagation in the implementation of manipulator on real system. The objects image captured by the digital camera were processed based on HSV-color model and the centroid coordinate of each object detected were calculated. These coordinates are end effector position target to pick each object and were placed to the ri…
Quantum Machine Learning and Grover's Algorithm for Quantum Optimization of Robotic Manipulators
Robotics Research Center of Yuyao（余姚机器人研究中心）；Robotics Institute of Zhejiang University（浙江大学机器人研究所）；State Key Laboratory of Fluid Power and Mechatronic Systems（流体动力与机械电子系统国家重点实验室）；Institute of Design Engineering（设计工程院）；University of New Brunswick（新不伦瑞克大学）
Forward and backward reaching inverse kinematics (FABRIK) is a heuristic inverse kinematics solver that is gradually applied to manipulators with the advantages of fast convergence and generating more realistic configurations. However, under the high error constraint, FABRIK exhibits unstable convergence behavior, which is unsatisfactory for the real-time motion planning of manipulators. In this paper, a novel inverse kinematics algorithm that combines FABRIK and the sequential quadratic programming (SQP) algorithm is presented, in which the joint angles deduced by FABRIK will be taken as the …
In this paper, a new numerical method to solve the forward kinematics (FK) of a parallel manipulator with three-limb spherical-prismatic-revolute (3SPR) structure is presented. Unlike the existing numerical approaches that rely on computation of the manipulator's Jacobian matrix and its inverse at each iteration, the proposed algorithm requires much less computations to estimate the FK parameters. A cost function is introduced that measures the difference of the estimates from the actual FK values. At each iteration, the problem is decomposed into two steps. First, the estimates of the platfor…
In this research, Artificial Neural Networks (ANNs) have been used as a powerful tool to solve the inverse kinematic equations of a parallel robot. For this purpose, we have developed the kinematic equations of a Tricept parallel kinematic mechanism with two rotational and one translational degrees of freedom (DoF). Using the analytical method, the inverse kinematic equations are solved for specific trajectory, and used as inputs for the applied ANNs. The results of both applied networks (Multi-Layer Perceptron and Redial Basis Function) satisfied the required performance in solving complex in…
CIIRC CTU in Prague（布拉格捷克理工大学信息、机器人与控制研究所）；Sorbonne Université, LIP6 CNRS（索邦大学，法国国家科学研究中心LIP6实验室）；LAAS-CNRS, FEE CTU in Prague（法国国家科学研究中心系统分析与架构实验室，布拉格捷克理工大学电气工程学院）
The Inverse Kinematics (IK) problem is to nd robot control parameters to bring it into the desired position under the kinematics and collision constraints. We present a global solution to the optimal IK problem for a general serial 7DOF manipulator with revolute joints and a quadratic polynomial objective function. We show that the kinematic constraints due to rotations can all be generated by second-degree polynomials. This is important since it signicantly simplies further step where we nd the optimal solution by Lasserre relaxations of non-convex polynomial systems. We demonstrate that the …
University of Cassino and Southern Lazio（卡西诺和南拉齐奥大学）
In this paper we present a framework that allows the motion control of a robotic arm automatically handling different kinds of safety-related tasks. The developed controller is based on a Task-Priority Inverse Kinematics algorithm that allows the manipulator's motion while respecting constraints defined either in the joint or in the operational space in the form of equality-based or set-based tasks. This gives the possibility to define, among the others, tasks as joint-limits, obstacle avoidance or limiting the workspace in the operational space. Additionally, an algorithm for the real-time co…
A redundant manipulator has multiple inverse kinematics solutions per end-effector pose. Accordingly, there can be many trajectories for joints that follow a given endeffector path in the Cartesian space. In this paper, we present a trajectory optimization of a redundant manipulator (TORM) to synthesize a trajectory that follows a given end-effector path accurately, while achieving smoothness and collisionfree manipulation. Our method holistically incorporates three desired properties into the trajectory optimization process by integrating the Jacobian-based inverse kinematics solving method a…
Unified Hierarchical MPC in Task Executing for Modular Manipulators across Diverse Morphologies
Humanoids and Human Centered Mechatronics Research Line, Istituto Italiano Di Tecnologia (IIT)（意大利理工学院人机一体化机电一体化研究组）；Tencent Robotics X Lab（腾讯机器人实验室）；The University of Hong Kong（香港大学）
INRIA（法国国家信息与自动化研究所）；Institut de Recherche en Cybernétique de Nantes（南特控制论研究所）
The goal of this paper is to define the n-connected regions in the Cartesian workspace of fully-parallel manipulators, i.e. the maximal regions where it is possible to execute point-to-point motions. The manipulators considered in this study may have multiple direct and inverse kinematic solutions. The N-connected regions are characterized by projection, onto the Cartesian workspace, of the connected components of the reachable configuration space defined in the Cartesian product of the Cartesian space by the joint space. Generalized octree models are used for the construction of all spaces. T…
Dynamic Programming-Based Redundancy Resolution for Path Planning of Redundant Manipulators Considering Breakpoints
School of Mathematical Sciences, Zhejiang University（浙江大学数学科学学院）；Zhejiang Demetics Medical Technology Co., Ltd.（浙江德美特斯医疗科技有限公司）；Teachers College, Columbia University（哥伦比亚大学教师学院）；Zhejiang College of Sports（浙江体育学院）；Shenzhen Institute for Advanced Study, University of Electronic Science and Technology of China（电子科技大学深圳高等研究院）
