We investigate a surface-mounted electrode geometry for miniature linear radio frequency Paul ion traps. The electrodes reside in a single plane on a substrate, and the pseudopotential minimum of the trap is located above the substrate at a distance on order of the electrodes' lateral extent or separation. This architecture provides the possibility to apply standard microfabrication principles to the construction of multiplexed ion traps, which may be of particular importance in light of recent proposals for large-scale quantum computation based on individual trapped ions.
We characterise the performance of a surface-electrode ion "chip" trap fabricated using established semiconductor integrated circuit and micro-electro-mechanical-system (MEMS) microfabrication processes which are in principle scalable to much larger ion trap arrays, as proposed for implementing ion trap quantum information processing. We measure rf ion micromotion parallel and perpendicular to the plane of the trap electrodes, and find that on-package capacitors reduce this to <~ 10 nm in amplitude. We also measure ion trapping lifetime, charging effects due to laser light incident on the trap…
We demonstrate a method for loading surface electrode ion traps by electron impact ionization. The method relies on the property of surface electrode geometries that the trap depth can be increased at the cost of more micromotion. By introducing a buffer gas, we can counteract the rf heating assocated with the micromotion and benefit from the larger trap depth. After an initial loading of the trap, standard compensation techniques can be used to cancel the stray fields resulting from charged dielectric and allow for the loading of the trap at ultra-high vacuum.
Dense arrays of trapped ions provide one way of scaling up ion trap quantum information processing. However, miniaturization of ion traps is currently limited by sharply increasing motional state decoherence at sub-100 um ion-electrode distances. We characterize heating rates in cryogenically cooled surface-electrode traps, with characteristic sizes in 75 um to 150 um range. Upon cooling to 6 K, the measured rates are suppressed by 7 orders of magnitude, two orders of magnitude below previously published data of similarly sized traps operated at room temperature. The observed noise depends str…
The prospect of building a quantum information processor underlies many recent advances ion trap fabrication techniques. Potentially, a quantum computer could be constructed from a large array of interconnected ion traps. We report on a micrometer-scale ion trap, fabricated from bulk silicon using micro-electromechanical systems (MEMS) techniques. The trap geometry is relatively simple in that the electrodes lie in a single plane beneath the ions. In such a trap we confine laser-cooled 24Mg+ ions approximately 40 microns above the surface. The fabrication technique and planar electrode geometr…
Surface-electrode (SE) rf traps are a promising approach to manufacturing complex ion-trap networks suitable for large-scale quantum information processing. In this paper we present analytical methods for modeling SE traps in the gapless plane approximation, and apply these methods to two particular classes of SE traps. For the SE ring trap we derive analytical expressions for the trap geometry and strength, and also calculate the depth in the absence of control fields. For translationally symmetric multipole configurations (analogs of the linear Paul trap), we derive analytical expressions fo…
For many quantum information implementations with trapped ions, effective shuttling operations are important. Here we discuss the efficient separation and recombination of ions in surface ion trap geometries. The maximum speed of separation and recombination of trapped ions for adiabatic shuttling operations depends on the secular frequencies the trapped ion experiences in the process. Higher secular frequencies during the transportation processes can be achieved by optimising trap geometries. We show how two different arrangements of segmented static potential electrodes in surface ion traps …
The oscillation coupling and different nonlinear effects are observed in a single trapped $^{40}Ca^{+}$ ion confined in our home-built surface-electrode trap (SET). The coupling and the nonlinearity are originated from the high-order multipole potentials due to different layouts and the fabrication asymmetry of the SET. We solve a complicated Duffing equation with coupled oscillation terms by the multiple scale method, which fits the experimental values very well. Our investigation in the SET helps for exploring nonlinearity using currently available techniques and for suppressing instability …
Dense array of ions in microfabricated traps represent one possible way to scale up ion trap quantum computing. The ability to address individual ions is an important component of such a scheme. We demonstrate individual addressing of trapped ions in a microfabricated surface-electrode trap using a magnetic field gradient generated on-chip. A frequency splitting of 310(2) kHz for two ions separated by 5 um is achieved. Selective single qubit operations are performed on one of two trapped ions with an average of 2.2+/-1.0% crosstalk. Coherence time as measured by the spin-echo technique is unaf…
We demonstrate loading by laser ablation of $^{88}$Sr$^+$ ions into a mm-scale surface-electrode ion trap. The laser used for ablation is a pulsed, frequency-tripled Nd:YAG with pulse energies of 1-10 mJ and durations of 3-5 ns. An additional laser is not required to photoionize the ablated material. The efficiency and lifetime of several candidate materials for the laser ablation target are characterized by measuring the trapped ion fluorescence signal for a number of consecutive loads. Additionally, laser ablation is used to load traps with a trap depth (40 meV) below where electron impact i…
We report heating rate measurements in a microfabricated gold-on-sapphire surface electrode ion trap with trapping height of approximately 240 micron. Using the Doppler recooling method, we characterize the trap heating rates over an extended region of the trap. The noise spectral density of the trap falls in the range of noise spectra reported in ion traps at room temperature. We find that during the first months of operation the heating rates increase by approximately one order of magnitude. The increase in heating rates is largest in the ion loading region of the trap, providing a strong hi…
We demonstrate confinement of individual atomic ions in a radio-frequency Paul trap with a novel geometry where the electrodes are located in a single plane and the ions confined above this plane. This device is realized with a relatively simple fabrication procedure and has important implications for quantum state manipulation and quantum information processing using large numbers of ions. We confine laser-cooled Mg-24 ions approximately 40 micrometer above planar gold electrodes. We measure the ions' motional frequencies and compare them to simulations. From measurements of the escape time o…
We measure and characterize anomalous motional decoherence of an atomic ion confined in the lowest quantum levels of a novel rf ion trap that features moveable electrodes. The scaling of decoherence rate with electrode proximity is measured, and when the electrodes are cooled from 300 K to 150 K, the decoherence rate is suppressed by an order of magnitude. This provides direct evidence that anomalous motional decoherence of trapped ions stems from microscopic noisy potentials on the electrodes. These observations are relevant to quantum information processing schemes using trapped ions or othe…
Chiaverini et al. [Quant. Inf. Comput. 5, 419 (2005)] recently suggested a linear Paul trap geometry for ion trap quantum computation that places all of the electrodes in a plane. Such planar ion traps are compatible with modern semiconductor fabrication techniques and can be scaled to make compact, many zone traps. In this paper we present an experimental realization of planar ion traps using electrodes on a printed circuit board to trap linear chains of tens of 0.44 micron diameter charged particles in a vacuum of 15 Pa (0.1 torr). With these traps we address concerns about the low trap dept…
We study the problem of designing electrode structures that allow pairs of ions to be brought together and separated rapidly in an array of linear Paul traps. We show that it is desirable for the electrode structure to produce a d.c. octupole moment with an a.c. radial quadrupole. For the case where electrical breakdown limits the voltages that can be applied, we show that the octupole is more demanding than the quadrupole when the characteristic distance scale of the structure is larger than 1 to 10 microns (for typical materials). We present a variety of approaches and optimizations of struc…
The fidelity of laser-driven quantum logic operations on trapped ion qubits tend to be lower than microwave-driven logic operations due to the difficulty of stabilizing the driving fields at the ion location. Through stabilization of the driving optical fields and use of composite pulse sequences, we demonstrate high fidelity single-qubit gates for the hyperfine qubit of a $^{171}\text{Yb}^+$ ion trapped in a microfabricated surface electrode ion trap. Gate error is characterized using a randomized benchmarking protocol, and an average error per randomized Clifford group gate of $3.6(3)\times1…
In ion trap quantum information processing, efficient fluorescence collection is critical for fast, high-fidelity qubit detection and ion-photon entanglement. The expected size of future many-ion processors require scalable light collection systems. We report on the development and testing of a microfabricated surface-electrode ion trap with an integrated high numerical aperture (NA) micromirror for fluorescence collection. When coupled to a low NA lens, the optical system is inherently scalable to large arrays of mirrors in a single device. We demonstrate stable trapping and transport of 40Ca…
Trapped ions offer long internal state (spin) coherence times and strong inter-particle interactions mediated by the Coulomb force. This makes them interesting candidates for quantum simulation of coupled lattices. To this end it is desirable to be able to trap ions in arbitrary conformations with precisely controlled local potentials. We provide a general method for optimizing periodic planar radio-frequency electrodes for generating ion trapping potentials with specified trap locations and curvatures above the electrode plane. A linear-programming algorithm guarantees globally optimal electr…
We demonstrate quantum control techniques for a single trapped ion in a cryogenic, surface-electrode trap. A narrow optical transition of Sr+ along with the ground and first excited motional states of the harmonic trapping potential form a two-qubit system. The optical qubit transition is susceptible to magnetic field fluctuations, which we stabilize with a simple and compact method using superconducting rings. Decoherence of the motional qubit is suppressed by the cryogenic environment. AC Stark shift correction is accomplished by controlling the laser phase in the pulse sequencer, eliminatin…
One path to realizing systems of trapped atomic ions suitable for large-scale quantum computing and simulation is to create a two-dimensional array of ion traps. Interactions between nearest-neighbouring ions could then be turned on and off by tuning the ions' relative positions and frequencies. We demonstrate and characterize the operation of a planar-electrode ion-trap array. Driving the trap with a network of phase-locked radio-frequency (RF) resonators which provide independently variable voltage amplitudes we vary the position and motional frequency of a 40Ca+ ion in two dimensions within…
In this paper we present the design, modeling, and experimental testing of surface electrode ion traps fabricated in a heterostructure configuration comprising a silicon substrate, silicon dioxide insulators, and aluminum electrodes. This linear trap has a geometry with symmetric RF leads, two interior DC electrodes, and 40 individual lateral DC electrodes. Plasma enhanced chemical vapor deposition (PECVD) was used to grow silicon dioxide pillars to electrically separate overhung aluminum electrodes from an aluminum ground plane. In addition to fabrication, we report techniques for modeling th…
We present approximate methods for calculating the three-dimensional electric potentials of finite surface electrodes including gaps between electrodes, and estimate the effects of finite electrode thickness and an underlying dielectric substrate. As an example we optimize a radio-frequency surface-electrode ring ion trap, and find that each of these factors reduces the trapping secular frequencies by less than 5% in realistic situations. This small magnitude validates the usual assumption of neglecting the influences of gaps between electrodes and finite electrode extent.
We describe the design, fabrication, and operation of a novel surface-electrode Paul trap that produces a radio-frequency-null along the axis perpendicular to the trap surface. This arrangement enables control of the vertical trapping potential and consequentially the ion-electrode distance via dc-electrodes only. We demonstrate confinement of single $^{40}$Ca$^+$ ions at heights between $50~μ$m and $300~μ$m above planar copper-coated aluminium electrodes. We investigate micromotion in the vertical direction and show cooling of both the planar and vertical motional modes into the ground state.…
We propose a surface ion trap design incorporating microwave control electrodes for near-field single-qubit control. The electrodes are arranged so as to provide arbitrary frequency, amplitude and polarization control of the microwave field in one trap zone, while a similar set of electrodes is used to null the residual microwave field in a neighbouring zone. The geometry is chosen to reduce the residual field to the 0.5% level without nulling fields; with nulling, the crosstalk may be kept close to the 0.01% level for realistic microwave amplitude and phase drift. Using standard photolithogra…
We have investigated motional heating of laser-cooled 9Be+ ions held in radio-frequency (Paul) traps. We have measured heating rates in a variety of traps with different geometries, electrode materials, and characteristic sizes. The results show that heating is due to electric-field noise from the trap electrodes which exerts a stochastic fluctuating force on the ion. The scaling of the heating rate with trap size is much stronger than that expected from a spatially uniform noise source on the electrodes (such as Johnson noise from external circuits), indicating that a microscopic uncorrelated…
We have developed an trapped ion system for producing two-dimensional (2D) ion crystals for applications in scalable quantum computing, quantum simulations, and 2D crystal phase transition and defect studies. The trap is a modification of a Paul trap with its ring electrode flattened and split into eight identical sectors, and its two endcap electrodes shaped as truncated hollow cones for laser and imaging optics access. All ten trap electrodes can be independently DC-biased to create various aspect ratio trap geometries. We trap and Doppler cool 2D crystals of up to 30 Ba+ ions and demonstrat…
We report on a surface-electrode trap with SmCo magnets arranged in a quadrupole configuration underneath the trap electrode. Because the distance between the magnets and the trapped ions can be as little as several hundred micrometers, a large magnetic field is produced without any heat management. The magnetic-field gradient was measured using the Zeeman splitting of a single trapped $^{40}$Ca$^+$ ion at several positions, and a field gradient of 36 T/m was obtained. Such a field gradient is useful for the generation of a state-dependent force, which is important for quantum simulation and/o…
We investigate electrode geometries required to produce periodic 2-dimensional ion-trap arrays with the ions placed between two planes of electrodes. We present a generalization of previous methods for traps containing a single electrode plane to this new geometry, and show that for a given ion-electrode distance and applied voltages, the inter-ion distance can be reduced by a factor of up to 3 relative to single-plane traps. This represents an increase by a factor of 9 in the trap density and a factor of 27 in the exchange coupling between the oscillatory motion of neighboring ions. The resul…
We describe an ex-situ surface-cleaning procedure that is shown to reduce motional heating from ion-trap electrodes. This precleaning treatment, to be implemented immediately before the final assembly and vacuum processing of ion traps, removes surface contaminants remaining after the electrode-fabrication process. We incorporate a multi-angle ion-bombardment treatment intended to clean the electrode surfaces and interelectrode gaps of microfabricated traps. This procedure helps to minimize redeposition in the gaps between electrodes that can cause electrical shorts. We report heating rates in…
We describe the advantages of 2-dimensional, addressable arrays of spherical Paul traps. They would provide for the ability to address and tailor the interaction strengths of trapped objects in 2D and could establish a valuable new tool for quantum information processing. Simulations of trapping ions are compared to first tests using printed circuit board trap arrays loaded with dust particles. Pair-wise interactions in the array are addressed by means of an adjustable radio-frequency (RF) electrode shared between trapping sites. By attenuating this RF electrode potential, neighboring pairs of…
We present a model as well as experimental results for a surface electrode radio-frequency Paul trap that has a circular electrode geometry well-suited for trapping of single ions and two-dimensional planar ion crystals. The trap design is compatible with microfabrication and offers a simple method by which the height of the trapped ions above the surface may be changed \emph{in situ}. We demonstrate trapping of single and few Sr+ ions over an ion height range of 200-1000 microns for several hours under Doppler laser cooling, and use these to characterize the trap, finding good agreement with …
We model electric field noise from fluctuating patch potentials on conducting surfaces by taking into account the finite geometry of the ion trap electrodes to gain insight into the origin of anomalous heating in ion traps. The scaling of anomalous heating rates with surface distance, $d$, is obtained for several generic geometries of relevance to current ion trap designs, ranging from planar to spheroidal electrodes. The influence of patch size is studied both by solving Laplace's equation in terms of the appropriate Green's function as well as through an eigenfunction expansion. Scaling with…
We describe the design of a surface-electrode ion trap junction, which is a key element for large-scale ion trap arrays. A bi-objective optimization method is used for designing the electrodes, which maintains the total pseudo-potential curvature while minimizing the axial pseudo-potential gradient along the ion transport path. To facilitate the laser beam delivery for parallel operations in multiple trap zones, we implemented integrated optics on each arm of this X-junction trap. The layout of the trap chip for commercial foundry fabrication is presented. This work suggests routes to improvin…
We present two simple cryogenic RF ion trap systems in which cryogenic temperatures and ultra high vacuum pressures can be reached in as little as 12 hours. The ion traps are operated either in a liquid helium bath cryostat or in a low vibration closed cycle cryostat. The fast turn around time and availability of buffer gas cooling made the systems ideal for testing surface-electrode ion traps. The vibration amplitude of the closed cycled cryostat was found to be below 106 nm. We evaluated the systems by loading surface-electrode ion traps with $^{88}$Sr$^+$ ions using laser ablation, which is…
We present the characterization of a prototype surface-electrode (SE) trap as a first step towards the realization of a compact, single-ion optical clock based on Yb$^+$. The use of a SE trap will be a key factor to benefit from clean-room fabrication techniques and technological advances made in the field of quantum information processing. We succesfully demonstrated trapping at a 500 $μ$m electrodes distance and characterized our trap in terms of lifetime and heating rate. This is to our knowledge the highest distance achieved for heating rates measurements in SE traps. This simple 5-wire de…
Anomalous heating of trapped atomic ions is a major obstacle to their use as quantum bits in a scalable quantum computer. The physical origin of this heating is not fully understood, but experimental evidence suggests that it is caused by electric-field noise emanating from the surface of the trap electrodes. In this study, we have investigated the role that adsorbates on the electrodes play by identifying contaminant overlayers, developing an in situ argon-ion beam cleaning procedure, and measuring ion heating rates before and after cleaning the trap electrodes' surfaces. We find a reduction …
We trap individual $^{171}$Yb$^+$ ions in a surface trap microfabricated on a silicon substrate, and demonstrate a complete set of high fidelity single qubit operations for the hyperfine qubit. Trapping times exceeding 20 minutes without laser cooling, and heating rates as low as 0.8(0.1) quanta/ms indicate stable trapping conditions in these microtraps. A coherence time of more than one second, high fidelity qubit state detection and single qubit rotations are demonstrated.
We report the design, fabrication, and characterization of a microfabricated surface-electrode ion trap that supports controlled transport through the two-dimensional intersection of linear trapping zones arranged in a ninety-degree cross. The trap is fabricated with very-large-scalable-integration (VLSI) techniques which are compatible with scaling to a larger quantum information processor. The shape of the radio-frequency (RF) electrodes is optimized with a genetic algorithm to minimize axial pseudopotential barriers and to minimize ion heating during transport. Seventy-eight independent DC …
There has been much interest in developing methods for transferring quantum information. We discuss a way to transfer quantum information between two trapped ions through a wire. The motion of a trapped ion induces oscillating charges in the trap electrodes. By sending this current to the electrodes of a nearby second trap, the motions of ions in the two traps are coupled. We investigate the electrostatics of a set-up where two separately trapped ions are coupled through an electrically floating wire. We also discuss experimental issues, including possible sources of decoherence.
We investigate anomalous ion-motional heating, a limitation to multi-qubit quantum-logic gate fidelity in trapped-ion systems, as a function of ion-electrode separation. Using a multi-zone surface-electrode trap in which ions can be held at five discrete distances from the metal electrodes, we measure power-law dependencies of the electric-field noise experienced by the ion on the ion-electrode distance $d$. We find a scaling of approximately $d^{-4}$ regardless of whether the electrodes are at room temperature or cryogenic temperature, despite the fact that the heating rates are approximately…
It was recently proposed to use small groups of trapped ions as qubit carriers in miniaturized electrode arrays that comprise a large number of individual trapping zones, between which ions could be moved. This approach might be scalable for quantum information processing with a large numbers of qubits. Processing of quantum information is achieved by transporting ions to and from separate memory and qubit manipulation zones in between quantum logic operations. The transport of ion groups in this scheme plays a major role and requires precise experimental control and fast transport. In this pa…
In this study, we report the first Cu-filled through silicon via (TSV) integrated ion trap. TSVs are placed directly underneath electrodes as vertical interconnections between ion trap and a glass interposer, facilitating the arbitrary geometry design with increasing electrodes numbers and evolving complexity. The integration of TSVs reduces the form factor of ion trap by more than 80%, minimizing parasitic capacitance from 32 to 3 pF. A low RF dissipation is achieved in spite of the absence of ground screening layer. The entire fabrication process is on 12-inch wafer and compatible with estab…
Radio-frequency linear multipole traps have been shown to be very sensitive to mis-positioning of their electrodes, which results in a symmetry breaking and leads to extra local minima in the trapping potential \cite{pedregosa17} disturbing the operation of the trap. In this work, we analytically describe the RF-potential of a realistic octupole trap by including lower order terms to the well-established equation for a perfectly symmetric octupole trap. We describe the geometry by a combination of identified defects, characterised by simple analytical expressions. A complete equation is propos…
We present designs for multipole ion traps based on a set of planar, annular, concentric electrodes which require only rf potentials to confine ions. We illustrate the desirable properties of the traps by considering a few simple cases of confined ions. We predict that mm-scale surface traps may have trap depths as high as tens of electron volts, or micromotion amplitudes in a 2-D ion crystal as low as tens of nanometers, when parameters of a magnitude common in the field are chosen. Several example traps are studied, and the scaling of those properties with voltage, frequency, and trap scale,…
We present a detailed study of quantum simulations of coupled spin systems in surface-electrode ion-trap arrays, and illustrate our findings with a proposed implementation of the hexagonal Kitaev model [A. Kitaev, Annals of Physics 321,2 (2006)]. The effective (pseudo)spin interactions making up such quantum simulators are found to be proportional to the dipole-dipole interaction between the trapped ions, and are mediated by motion which can be driven by state-dependent forces. The precise forms of the trapping potentials and the interactions are derived in the presence of a surface electrode …
We demonstrate a microfabricated surface-electrode ion trap that is applicable as a nanofriction emulator and studies of many-body dynamics of interacting systems. The trap enables both single-well and double-well trapping potentials in the radial direction, where the distance between the two potential wells can be adjusted by the applied RF voltage. In the double-well configuration, parallel ion strings can be formed, which is a suitable system for the emulation of the Frenkel-Kontorova (FK) model. We derive the condition under which the trap functions as a FK model emulator. The trap is desi…
We present a simple cryostat purpose built for use with surface-electrode ion traps, designed around an affordable, large cooling power commercial pulse tube refrigerator. A modular vacuum enclosure with a single vacuum space facilitates interior access, and enables rapid turnaround and flexiblity for future modifications. Long rectangular windows provide nearly 360 degrees of optical access in the plane of the ion trap, while a circular bottom window near the trap enables NA 0.4 light collection without the need for in-vacuum optics. We evaluate the system's mechanical and thermal characteris…
The majority of microfabricated ion traps in use for quantum information processing are of the 2D 'surface-electrode' type or of the 3D 'wafer' type. Surface-electrode traps greatly simplify fabrication and hold the promise of allowing trapped-ion quantum computers to scale via standard semiconductor industry fabrication techniques. However, their geometry constrains them to having much lower trapping efficiency, depth, and harmonicity compared to 3D geometries. Conversely 3D geometries offer superior trap performance but fabrication is more complex, limiting potential to scale. We describe ne…
Electric field noise is a major source of motional heating in trapped ion quantum computation. While the influence of trap electrode geometries on electric field noise has been studied in patch potential and surface adsorbate models, only smooth surfaces are accounted for by current theory. The effects of roughness, a ubiquitous feature of surface electrodes, are poorly understood. We investigate its impact on electric field noise by deriving a rough-surface Green's function and evaluating its effects on adsorbate-surface binding energies. At cryogenic temperatures, heating rate contributions …
Two-dimensional crystals of trapped ions are a promising system with which to implement quantum simulations of challenging problems such as spin frustration. Here, we present a design for a surface-electrode elliptical ion trap which produces a 2-D ion crystal and is amenable to microfabrication, which would enable higher simulated coupling rates, as well as interactions based on magnetic forces generated by on-chip currents. Working in an 11 K cryogenic environment, we experimentally verify to within 5% a numerical model of the structure of ion crystals in the trap. We also explore the possib…
We measure ion heating following transport throughout a Y-junction surface-electrode ion trap. By carefully selecting the trap voltage update rate during adiabatic transport along a trap arm, we observe minimal heating relative to the anomalous heating background. Transport through the junction results in an induced heating between 37 and 150 quanta in the axial direction per traverse. To reliably measure heating in this range, we compare the experimental sideband envelope, including up to fourth-order sidebands, to a theoretical model. The sideband envelope method allows us to cover the inter…
