We demonstrate the operation of an ultra low repetition rate, high peak power, picosecond diode pumped Nd:YVO4 passively mode locked laser oscillator. Repetition rates even below 1 MHz were achieved with the use of a new design multiple-pass cavity and a semiconductor saturable absorber. Long term stable operation at 1.2 MHz, pulse duration of 16.3 ps and average output power of 470 mW corresponding to 24 KW peak power pulses is reported. This is, to our knowledge, the lowest repetition rate high peak power pulses ever generated directly from a picosecond laser resonator without cavity dumping.
the realization of high repetition rate passively Q-switched monolithic microlaser is a challenge since a decade. To achieve this goal, we report here on the first passively Q-switched diode-pumped microchip laser based on the association of a Nd:GdVO4 crystal and a Cr4+:YAG saturable absorber. The monolithic design consists of 1 mm long 1% doped Nd:GdVO4 optically contacted on a 0.4 mm long Cr4+:YAG leading to a plano-plano cavity. A repetition rate as high as 85 kHz is achieved. The average output power is approximately 400 mW for 2.2 W of absorbed pump power and the pulse length is 1.1 ns.
We present the first direct observation of the bound state of multiple dissipative optical solitons in which bond length and bond strength can be individually controlled in a broad range in a regular manner. We have observed experimentally a new type of stable and extremely elastic soliton crystals that can be stretched and compressed many times conserving their structure by adjusting the bond properties in real time in a specially designed passively mode-locked fiber laser incorporating highly asymmetric tunable Mach-Zehnder interferometer. The temporal structure and dynamics of the generated…
We report on the observation of a novel mode locked optical comb generated at the Raman offset (Raman comb) in an optically pumped crystalline whispering gallery mode resonator. Mode locking is confirmed via measurement of the radio-frequency beat note produced by the optical comb on a fast photodiode. Neither the conventional Kerr comb nor hyper-parametric oscillation is observed when the Raman comb is present.
Liquid dye lasers have long been considered as ideal tunable laser sources in the visible range but are bulky, expensive, and require a complex system for dye circulation. Here, we present a system that relies on a low-cost blue laser diode as the pump source and a sealed dye cell with no flowing circuitry, resulting in a device that combines the convenience and size of a solid-state device with the stability of a liquid organic laser. A very high photo-stability is obtained (up to 1.2 x 10$^9$ pulses or 12 days at 1 kHz), which is five orders of magnitude higher than a solid-state dye laser o…
We have used injection locking to multiply the repetition rate of a passively mode-locked femtosecond fiber laser from 40 MHz to 1 GHz while preserving optical phase coherence between the master laser and the slave output. The system is implemented almost completely in fiber and incorporates gain and passive saturable absorption. The slave repetition rate is set to a rational harmonic of the master repetition rate, inducing pulse formation at the least common multiple of the master and slave repetition rates.
A highly stable diode-pumped circulation-free liquid dye laser in a vertical external cavity is reported. The design is simple (no fabrication process step required, no fluid circuitry), compact (~ cm sized), and cost-effective. An optical efficiency of 18% with a M${}^2$ of 1 are reported, with an excellent photostability-no efficiency drop was seen after 1.4 million pulses at 50 Hz, a value comparable to flowing systems and much higher than values achievable with organic solid-state lasers. We show that thermal effects are central in the stability and also on the dynamics of this laser. The …
Here, we demonstrate all-fiber direct amplification of 11 picosecond pulses from a gain-switched laser diode at 1063nm. The diode was driven at a repetition rate of 40MHz and delivered 13$μ$W of fiber-coupled average output power. For the low output pulse energy of 0.33pJ we have designed a multi-stage core pumped preamplifier based on single clad Yb-doped fibers in order to keep the contribution of undesired amplified spontaneous emission as low as possible and to minimize temporal and spectral broadening. After the preamplifier we reduced the 40MHz repetition rate to 1MHz using a fiber coupl…
Dissipative Kerr solitons (DKSs) intrinsically exhibit two degrees of freedom through their group and phase rotation velocity. Periodic extraction of the DKS into a waveguide produces a pulse train and yields the resulting optical frequency comb's repetition rate and carrier-envelope offset, respectively. Here, we demonstrate that it is possible to create a system with a single repetition rate but two different phase velocities by employing dual driving forces. By recasting these phase velocities into frequencies, we demonstrate, experimentally and theoretically, that they can mix and create n…
Continuous-wave mode-locked femtosecond 2 um solid-state laser with a c-cut Tm:CaYAlO4 as gain medium was experimentally demonstrated. The mode locked laser generated stable pulses with average output power as high as 531 mW, pulse duration of 496 fs, and repetition rate of 97 MHz at 1975 nm. The research results show that Tm:CaYAlO4 is an excellent gain medium for femtosecond pulse generation at 2um wavelength.
We present a tunable, hybrid waveguide-fiber optical parametric oscillator (OPO) synchronously pumped by an ultra-fast fiber laser exploiting four-wave mixing (FWM) generated in silicon nitride waveguides. Parametric oscillation results in a 35 dB enhancement of the idler spectral power density in comparison to spontaneous FWM, with the ability of wide wavelength tuning over 86 nm in the O-band. Measurements of the oscillation threshold and the efficiency of the feedback loop reveal how an integration of the OPO on a single silicon nitride chip can be accomplished at standard repetition rates …
Soliton microcombs offer the prospect of advanced optical metrology and timing systems in compact form factors. In these applications, pumping of microcombs directly from a semiconductor laser without amplification or triggering components is desirable for reduced power operation and to simplify system design. At the same time, low repetition rate microcombs are required in many comb applications for interface to detectors and electronics, but their increased mode volume makes them challenging to pump at low power. Here, 10 GHz repetition rate soliton microcombs are directly pumped by low-powe…
We demonstrate the broadband supercontinuum (SC) generation in photonic crystal fiber (PCF), highly nonlinear fiber (HNLF) and ZBLAN (ZrF4-BaF2-LaF3-AlF3-NaF) fiber with a passively mode-locked erbium-doped fiber laser (EDFL). The passively mode-locked EDFL incorporates a CNT-based saturable absorber and has achieved a pulse width of 620 fs with a pulse repetition rate of 18 MHz. The spectral broadening phenomena inside each fiber has been observed with respect to the variation in seed pulse power. The SC spectrum bandwidth of 1050 nm, 1400 nm, and 2000 nm has been achieved using PCF, HNLF, an…
Stable 30 fs pulses centered at 1068 nm (less than 10 optical cycles) are demonstrated in a diode pumped Yb:CaYAlO4 laser by using high-quality chemical vapor deposited monolayer graphene as the saturable absorber. The mode locked 8.43 optical-cycle pulses have a spectral bandwidth of ~ 50 nm and a pulse repetition frequency of ~ 113.5 MHz. To our knowledge, this is the shortest pulse ever reported for graphene mode-locked lasers and mode-locked Yb-doped bulk lasers. Our experimental results demonstrate that graphene mode locking is a very promising practical technique to generate few-cycle op…
We present a novel approach for the analysis of passively mode-locked semiconductor lasers that allows for efficient parameter sweeps and time jitter analysis. It permits accessing the ultra-low repetition rate regime where pulses become localized states. The analysis including slow (e.g. thermal) processes or transverse dynamics becomes feasible. Our method bridges the divide between the phenomenological, yet highly efficient, pulse iterative model that is the Haus master equation, and the more involved first principle descriptions relying on time delayed equations. Our iterative functional m…
We experimentally demonstrate a passively Q-switched erbium-doped fiber laser (EDFL) operation by using a saturable absorber based on Fe3O4 nanoparticles (FONP) in magnetic fluid (MF). As a kind of transition metal oxide, the FONP has a large nonlinear optical response with a fast response time for saturable absorber. By depositing MF at the end of optical fiber ferrule, we fabricated a FONP-based saturable absorber, which enables a strong light-matter interaction owing to the confined transmitted optical field within the single mode fiber. Because of large third-order optical nonlinearities o…
Ultrahigh repetition rate lasers will become vital light sources for many future technologies; however, their realization is challenging because the cavity size must be minimized. Whispering-gallery-mode (WGM) microresonators are attractive for this purpose since they allow the strong light-matter interaction usually needed to enable mode-locking. However, the optimum parameter ranges are entirely unknown since no experiments have yet been conducted. Here, we numerically investigate pulsed operation in a toroidal WGM microresonator with gain and saturable absorption (SA) to study the experimen…
We report on an in-band pumped SESAM mode-locked Ho:CALGO bulk laser with a record-high average power of 8.7 W and an optical-to-optical efficiency of 38.2% at a central wavelength of 2.1 um. At this power level, the bulk laser generates pulses with a duration of 369 fs at 84.4-MHz repetition rate, corresponding to a pulse energy of 103 nJ and a peak power of 246 kW. To the best of our knowledge, this is the highest average power and pulse energy directly generated from a mode-locked bulk laser in the 2-3 um wavelength region. Our current results indicate that Ho:CALGO is a competitive candida…
We show that both the power and repetition rate of a frequency comb generated in a nonlinear ring resonator, pumped with continuous wave (cw) coherent light, are modulated. The modulation is brought about by the interaction of the cw background with optical pulses excited in the resonator, and occurs in resonators with nonzero high-order chromatic dispersion and wavelength-dependent quality factor. The modulation frequency corresponds to the detuning of the pump frequency from the eigenfrequency of the pumped mode in the resonator.
We present a 100 MHz repetition rate Yb-fiber-laser-pumped synchronously pumped optical parametric oscillator (SPOPO) delivering tunable frequency combs covering almost the entire visible spectral range. By intracavity doubling both the signal and idler combs and using collinear residual pump light, nearly continuous tuning over the range of 420-700 nm is achieved with only small gaps near the OPO degeneracy condition. Output powers range from 10 mW to 200 mW, depending on wavelength, with pulse durations below 150 fs without external compression. Frequency locking of all three collinearly out…
We describe an efficient laser emission from a directly grown Er3+:YAG single-crystal fiber that is resonantly pumped using a continuous-wave (CW) laser diode at 1532 nm. In a longitudinal pumping, it emits 12.5 W at 1645 nm with a slope efficiency of 32%, which is the highest ever reported for a directly grown Er:YAG single-crystal fiber laser. Using an off-axis pumping scheme, CW output powers up to 7.3 W can be reached and in Q-switched operation, the laser produces 2 mJ pulses with a duration of 38 ns at the repetition rate of 1 kHz with an M^{2} factor below 1.8. To our knowledge this is …
We demonstrate a broadband mid-infrared (MIR) frequency comb source based on difference frequency generation (DFG) in periodically poled lithium niobate (PPLN) crystal. Mid-infrared radiation is obtained via mixing of the output of a 125 MHz repetition rate Yb-doped fiber laser with Raman-shifted solitons generated from the same source in a highly nonlinear fiber. The resulting idler is tunable in the range of 2.7 - 4.2 μm with average output power reaching 237 mW, and pulses as short as 115 fs. The coherence of the MIR comb is confirmed by spectral interferometry and heterodyne beat measureme…
We demonstrate a compact source of energetic and phase-locked multi-terahertz pulses at a repetition rate of 190 kHz. Difference frequency mixing of the fundamental output of an Yb:KGW amplifier with the idler of an optical parametric amplifier in GaSe and LiGaS2 crystals yields a passively phase-locked train of waveforms tunable between 12 and 42 THz. The shortest multi-terahertz pulses contain 1.8 oscillation cycles within the intensity FWHM. Pulse energies of up to 0.16 μJ and peak electric fields of 13 MV/cm are achieved. Electro-optic sampling reveals a phase stability better than 0.1 $π$…
Correlated photon pairs generated through spontaneous parametric down-conversion (SPDC) are a key resource in quantum optics. In many quantum optics applications, such as satellite quantum key distribution (QKD), a compact, high repetition rate pump laser is required. Here we demonstrate the use of a compact, GHz-rate diode-pumped three-element Kerr-lens-modelocked Ti:sapphire laser for the generation of correlated photon pairs at 790 nm. We verify the presence of indistinguishable photons produced via SPDC using Hong-Ou-Mandel (HOM) interferometry and observe a dip in coincidence counts with …
Within a synchronously pumped optical parametric oscillator (SPOPO), the inherent synchronism between the pump and the resonating signal is the magic to partly transfer the coherence property of the pump to the signal. In our demonstration, Vernier effect is observed within a femtosecond SPOPO by simply detuning the FSR of the cavity, generating signal pulses at tunable repetition rate from several GHz to 1 THz with a maximum 22.58 nm full width half maximum (FWHM) bandwidth supporting 160 fs pulses covering the C- and L-bands of the telecom wavelength region. This technique offers a simple me…
The repetition rate stabilization of an optical frequency comb based on diode-pumped solid-state laser technology is demonstrated using an intra-cavity electro-optic modulator. The large feedback bandwidth of such modulators allows disciplining the comb repetition rate on a cavity-stabilized continuous-wave laser with a locking bandwidth up to 700 kHz. This surpasses what can be achieved with any other type of actuator reported so far. An in-loop integrated phase noise of 133 mrad has been measured and the PM-to-AM coupling of the electro-optic modulator has been investigated as well.
We report mode-locked ~1550 nm output of transform-limited ~180 fs pulses from a large mode-area (diameter ~ 50 μm) guided-wave erbium fluorozirconate glass laser. The passively mode-locked oscillator generates pulses with 25 nm bandwidth at 156 MHz repetition rate and peak-power of 260 W. Scalability to higher repetition rate is demonstrated by transform-limited 410 fs pulse output at 1.3 GHz. To understand the origins of the broad spectral output, the laser cavity is simulated by using a numerical solution to the Ginzburg-Landau equation. This paper reports the widest bandwidth and shortest …
We demonstrated all-fiber amplification of 11 ps pulses from a gain-switched laser diode at 1064 nm. The diode was driven at a repetition rate of 40 MHz and delivered 13 $μ$W of fiber-coupled average output power. For the low output pulse energy of 325 fJ we have designed a multi-stage core pumped pre-amplifier in order to keep the contribution of undesired amplified spontaneous emission as low as possible. By using a novel time-domain approach for determining the power spectral density ratio (PSD) of signal to noise, we identified the optimal working point for our pre-amplifier. After the pre…
High-precision passive stabilization of repetition rate for a mode-locked fiber laser based on optical pulse injection
East China Normal University（华东师范大学）；University of Shanghai for Science and Technology（上海理工大学）；Chongqing Institute of East China Normal University（华东师范大学重庆研究院）；Jinan Institute of Quantum Technology（济南量子技术研究院）；Shanghai Research Center for Quantum Sciences（上海量子科学研究中心）
The thermal lensing effects in the lasing crystal appear to be dominant when the pump laser focused on the lasing crystal which causes the local heating effect. The spatial refractive index variations observed if the crystal has non-uniform temperature distribution. In the present study, the demonstration of thermal lensing effect of Brewster-cut Ti: Sapphire crystal carried out when pumped by 25 ps pulses at 80 MHz repetition rate with 532 nm central wavelength, while the average pump power controlled by the attenuator. The thermal lensing effects measured first at the ~293 K temperature and …
Kerr microresonators driven in the normal dispersion regime typically require the presence of localized dispersion perturbations, such as those induced by avoided mode crossings, to initiate the formation of optical frequency combs. In this work, we experimentally demonstrate that this requirement can be lifted by driving the resonator with a pulsed pump source. We also show that controlling the desynchronization between the pump repetition rate and the cavity free-spectral range (FSR) provides a simple mechanism to tune the center frequency of the output comb. Using a fiber mini-resonator wit…
Pulses as short as 260 fs have been generated in a diode-pumped low-gain Er:Yb:glass laser by exploiting the nonlinear optical response of single-layer graphene. The application of this novel material to solid-state bulk lasers opens up a way to compact and robust lasers with ultrahigh repetition rates.
We present a 2-\mum frequency comb based on a reliable mode-locked Er:fiber laser with 100 MHz repetition rate. After shifting the spectrum of the amplified Er:fiber comb to longer wavelengths, a single-clad Tm/Ho:fiber is used as a self-pumped pre-amplifier to generate a coherent and broadband spectrum centered at 1.93 \mum. Subsequently, a cladding-pumped Tm:fiber amplifier boosts the system to a maximum output power of 4.8 W at 1.96 \mum. After compression in a compact grating compressor, our amplified Er:fiber/Tm:fiber hybrid system delivers as much as 2.9 W with a pulse duration of 141 fs…
We report on a multi-mJ 2.1-$μ$m OPCPA system operating at a 1-kHz repetition rate, pumped by a picosecond cryogenic Yb:YAG pump laser, and the phase-matched high-flux high-harmonic soft X-ray generation.
We show that a 1.13-GHz repetition rate optical pulse train with 0.70 fs high-frequency timing jitter (integration bandwidth of 17.5 kHz - 10 MHz, where the measurement instrument-limited noise floor contributes 0.41 fs in 10 MHz bandwidth) can be directly generated from a free-running, single-mode diode-pumped Yb:KYW laser mode-locked by single-walled carbon nanotube (SWCNT)-coated mirrors. To our knowledge, this is the lowest timing jitter optical pulse train with the GHz repetition rate ever measured. If this pulse train is used for direct sampling of 565-MHz signals (Nyquist frequency of t…
Dual-comb lasers from which asynchronous ultrashort pulses can be simultaneously generated have recently become an interesting research subject. They could be an intriguing alternative to the current dual-laser optical-frequency-comb source with highly sophisticated electronic control systems. If generated through a common light path traveled by all pulses, the common-mode noises between the spectral lines of different pulse trains could be significantly reduced. Therefore, coherent dual-comb generation from a completely common-path, unidirectional lasing cavity would be an interesting territo…
We consider interaction of counter-propagating waves in a bi-directionally pumped ring microresonator with Kerr nonlinearity. We introduce a hierarchy of the mode expansions and envelope functions evolving on different time scales set by the cavity linewidth and nonlinearity, dispersion, and repetition rate, and provide a detailed derivation of the corresponding hierarchy of the coupled mode and of the Lugiato-Lefever-like equations. An effect of the washout of the repetition rate frequencies from the equations governing dynamics of the counter-propagating waves is elaborated in details.
Four-wave mixing (FWM) in optical fibre is a leading technique for generating high-quality photon pairs. We report the generation of photon pairs by spontaneous FWM in photonic crystal fibre pumped by a 1.5 GHz repetition-rate vertical-external-cavity surface-emitting laser (VECSEL). The photon pairs exhibit high count rates and a coincidence-to-accidental ratio of over 80. The VECSEL's high repetition-rate, high average power, tunability, and small footprint make this an attractive source for quantum key distribution and photonic quantum-state engineering.
In this paper, we present an experimental study of the metrological stabilization of a solid-state frequency comb for embedded metrology applications. The comb is a passively mode-locked laser diode based on InGaAs/InP Quantum-dash structure emitting optical lines into a 9 nm bandwidth centered at 1.55 $μ$m with a repetition rate of 10.09 GHz. The frequency stabilization is achieved by optical injection locking of the comb with an external cavity laser diode referenced onto a metrological frequency standard. One observes the transfer of the spectral purity from the injection laser to the neigh…
We report a few-cycle, broadband, singly-resonant optical parametric oscillator (OPO) for the mid-infrared based on MgO-doped periodically-poled LiNbO3 (MgO:PPLN), synchronously pumped by a 20-fs Ti:sapphire laser. By using crystal interaction lengths as short as 250 um, and careful dispersion management of input pump pulses and the OPO resonator, near-transform-limited, few-cycle idler pulses tunable across the mid-infrared have been generated, with as few as 3.7 optical cycles at 2682 nm. The OPO can be continuously tuned over 2179-3732 nm by cavity delay tuning, providing up to 33 mW of out…
Mid-infrared saturable absorber mirror is successfully fabricated by transferring the mechanically exfoliated black phosphorus onto the gold-coated mirror. With the as-prepared black phosphorus saturable absorber mirror, a continuous-wave passively mode-locked Er:ZBLAN fiber laser is demonstrated at the wavelength of 2.8 um, which delivers a maximum average output power of 613 mW, a repetition rate of 24 MHz and a pulse duration of 42 ps. To the best of our knowledge, it is the first time to demonstrate black phosphorus mode-locked laser at 2.8 um wavelength. Our results demonstrate the feasib…
A fully integrated dispersion-managed femtosecond mode-locked laser
Institute of Physics, Swiss Federal Institute of Technology Lausanne (EPFL)（洛桑联邦理工学院物理研究所）；Institute of Electrical and Micro Engineering, Swiss Federal Institute of Technology Lausanne (EPFL)（洛桑联邦理工学院电气与微工程学院）；EDWATEC SA（EDWATEC公司）；Helmholtz-Zentrum Dresden-Rossendorf (HZDR)（德累斯顿-罗森多夫亥姆霍兹中心）
We report the first demonstration to our knowledge of a continuously tunable picosecond laser operating around 1 MHz. The emission can be tuned from 640 to 685 nm and the repetition rate from 200 kHz to 1 MHz with a pulse duration of less than 200 ps. The system is based on a Nd:YVO4 passively Q-switched microchip laser providing a few tens of nJ per pulse. Two cascaded stages of amplification are then used to increase the pulse energy to several microJ . The frequency doubled radiation is then used to pump a periodically-poled-niobate-lithium (PPLN)-based optical parametric generator in an al…
Long-wavelength mid-infrared frequency combs with high power and flexible tunability are highly desired for molecular spectroscopy, including investigation of large molecules such as C60. We present a high power, phase-stabilized frequency comb near 10 μm, generated by a synchronously-pumped, singly-resonant optical parametric oscillator (OPO) based on AgGaSe2. The OPO can be continuously tuned from 8.4 to 9.5 μm, with a maximum average idler power of 100 mW at the center wavelength of 8.5 μm. Both the repetition rate (frep) and the carrier-envelop offset frequency (fceo) of the idler wave are…
