This paper presents an investigation of organic LED extraction efficiency enhancement using a low refractive index scattering layer. A scattering model is developed based on rigorous electromagnetic modelling techniques. The model accounts for proportions of scattered guided and radiation modes as well as the efficiencies with which emitted and scattered light are extracted. Constrained optimisation techniques are implemeneted for a single operation wavelength to maximise the extraction efficiency of a generic OLED device. Calculations show that a 2 fold efficiency enhancement is achievable with a correctly engineered scattering layer. The detailed analysis of the enhancement mechanism highlights ways in which this scheme could be improved.
High-power, diffraction-limited organic solid-state laser operation has been achieved in a vertical external cavity surface-emitting organic laser (VECSOL), pumped by a low-cost compact blue laser diode. The diode-pumped VECSOLs were demonstrated with various dyes in a polymer matrix, leading to laser emissions from 540 nm to 660 nm. Optimization of both the pump pulse duration and output coupling leads to a pump slope efficiency of 11% for a DCM based VECSOLs. We report output pulse energy up to 280 nJ with 100 ns long pump pulses, leading to a peak power of 3.5 W in a circularly symmetric, d…
We compare fundamental characteristics of proposed electrically pumped subwavelength plasmonic lasers (spasers) with ubiquitous all-dielectric semiconductor micro-lasers (VCSEL) and indicate their close similarities as well as large differences in performance (threshold, efficiency, coherence and speed). These results should assist researchers in making informed choice of the emitter for each particular opto-electronic application.
The changes in excitation dependence of efficiency with temperature is modeled for a wurtzite InGaN light-emitting diode. The model incorporates bandstructure changes with carrier density arising from screening of quantum-confined Stark effect. Bandstructure is computed by solving Poisson and k.p equations in the envelop approximation. The information is used in a dynamical model for populations in momentum-resolved electron and hole states. Application of the approach shows the interplay of quantum-well and barrier emissions giving rise to shape changes in efficiency versus current density wi…
We report here a monolithic photonic integration of light emitting diode (LED) with waveguide and photodetector to build a highly-integrated photonic system to perform functionalities on the GaN-on-silicon platform. Suspended p-n junction InGaN/GaN multiple quantum wells (MQWs) are used for device fabrication. Part of the LED emission is coupled into suspended waveguide and then, the guided light laterally propagates along the waveguide and is finally sensed by the photodetector. Planar optical communication experimentally demonstrates that the proof-of-concept monolithic photonic integration …
We study light transport in phosphor plates of white light-emitting diodes (LEDs). We measure the broadband diffuse transmission through phosphor plates of varying YAG:Ce$^{3+}$ density. We distinguish the spectral ranges where absorption, scattering, and re-emission dominate. Using diffusion theory, we derive the transport and absorption mean free paths from first principles. We find that both transport and absorption mean free paths are on the order of the plate thickness. This means that phosphors in commercial LEDs operate well within an intriguing albedo range around 0.7. We discuss how s…
We demonstrate enhanced light extraction for monochrome top-emitting organic light-emitting diodes (OLEDs). The enhancement by a factor of 1.2 compared to a reference sample is caused by the use of a hole transport layer (HTL) material possessing a low refractive index (1.52). The low refractive index reduces the in-plane wave vector of the surface plasmon polariton (SPP) excited at the interface between the bottom opaque metallic electrode (anode) and the HTL. The shift of the SPP dispersion relation decreases the power dissipated into lost evanescent excitations and thus increases the outcou…
We present results on electrically driven nanobeam photonic crystal cavities formed out of a lateral p-i-n junction in gallium arsenide. Despite their small conducting dimensions, nanobeams have robust electrical properties with high current densities possible at low drive powers. Much like their two-dimensional counterparts, the nanobeam cavities exhibit bright electroluminescence at room temperature from embedded 1,250 nm InAs quantum dots. A small room temperature differential gain is observed in the cavities with minor beam self-heating suggesting that lasing is possible. These results ope…
Virtually all light-emitting diodes (LEDs) are encapsulated with a transparent epoxy or silicone-gel. In this paper we analyze the optical efficiency of spherical encapsulants. We develop a quasi-radiometric equation for the light transmission efficiency, which incorporates some ideas of Monte-Carlo ray tracing into the context of radiometry. The approach includes the extended source nature of the LED chip, and the chip radiance distribution. The equation is an explicit function of the size and the refractive index of the package, and also of several chip parameters such as shape, size, radian…
A solid-state organic thin-film laser with intracavity frequency doubling is reported. Tunable ultraviolet emission from 309 to 322 nm is achieved from a vertical external cavity surface-emitting organic laser, with 2 % efficiency (1 $μ$J at 315 nm). The laser comprises a polymethyl(methacrylate) layer doped with Rhodamine 640, spun-cast onto a plane mirror, a remote concave mirror, a nonlinear crystal and a dichroic separator. The output is spectrally narrow (<0.5 nm FWHM) and tunable through phase-matching selection of the fundamental radiation lasing modes. These results highlight a low-cos…
This article presents the use of flexible carbon substrates for the growth of III-nitride nanowire light emitters. A dense packing of gallium nitride nanowires were grown on a carbon paper substrate. The nanowires grew predominantly along the a-plane direction, normal to the local surface of the carbon paper. Strong photo- and electro-luminescence was observed from InGaN quantum well light emitting diode nanowires.
The enhancement of the power conversion efficiency (PCE), and subsequent reduction of cost, of light emitting diodes (LEDs) is of crucial importance in the current lightening market. For this reason, we propose here a PCE-enhanced LED architecture, based on a partially reflecting metasurface cavity (PRMC) structure. This structure simultaneously enhances the light extraction efficiency (LEE) and the spontaneous emission rate (SER) of the LED by enforcing the emitted light to radiate perpendicularly to the device, so as to suppress wave trapping and enhance field confinement near the emitter, w…
Light emitting diodes (LEDs) based on Gallium Nitride (GaN) have been revolutionizing various applications in lighting, displays, medical equipment, and other fields. However, their energy efficiency is still below expectations in many cases. An unprecedented diversity of theoretical models has been developed for efficiency analysis and GaN-LED design optimization. This review paper provides an overview of the modeling landscape and pays special attention to the influence of III-nitride material properties. It thereby identifies some key challenges and directions for future improvements.
Bandstructure properties in wurtzite quantum wells can change appreciably with changing carrier density because of screening of quantum-confined Stark effect. An approach for incorporating these changes in an InGaN light-emitting-diode model is described. Bandstructure is computed for different carrier densities by solving Poisson and k\cdotp equations in the envelop approximation. The information is used as input in a dynamical model for populations in momentum-resolved electron and hole states. Application of the approach is illustrated by modeling device internal quantum efficiency as a fun…
Concentration quenching is a major impediment to efficient organic light-emitting devices. We herein report on Organic Light-Emitting Diodes (OLEDs) based on a fluorescent amorphous red-emitting starbust triarylamine molecule (4-di(4'-tert-butylbiphenyl-4-yl)amino-4'-dicyanovinylbenzene, named FVIN), exhibiting a very small sensitivity to concentration quenching. OLEDs are fabricated with various doping levels of FVIN into Alq3, and show a remarkably stable external quantum efficiency of 1.5% for doping rates ranging from 5% up to 40%, which strongly relaxes the technological constraints on th…
We demonstrate cryogenic, electrically-injected, waveguide-coupled Si light-emitting diodes (LEDs) operating at 1.22 $μ$m. The active region of the LED consists of W centers implanted in the intrinsic region of a $p$-$i$-$n$ diode. The LEDs are integrated on waveguides with superconducting nanowire single-photon detectors (SNSPDs). We demonstrate the scalability of this platform with an LED coupled to eleven SNSPDs in a single integrated photonic device. Such on-chip optical links may be useful for quantum information or neuromorphic computing applications.
The absorption of a metallic cathode in OLEDs is analyzed by using FDTD calculation. As the light propagates parallel to the layer, the intensity of Ez polarization decreases rapidly. The intensity at 2.0 um from the dipole is less than a quarter of that at 0.5 um. The strong absorption by a cathode can be a critical factor when considering the increase of optical extraction by means of bending the optical layers. The calculation indicates that the corrugation of layers helps the guided light escape the guiding layer, but also increases the absorption into a metallic cathode. The final optical…
We demonstrate arbitrary helicity control of circularly polarized light (CPL) emitted at room temperature from the cleaved side-facet of a lateral-type spin-polarized light-emitting diode (spin-LED) with two ferromagnetic electrodes in an anti-parallel magnetization configuration. Driving alternate currents through the two electrodes results in polarization switching of CPL with frequencies up to 100 kHz. Furthermore, tuning the current density ratio in the two electrodes enables manipulation of the degree of circular polarization. These results demonstrate arbitrary electrical control of pola…
V-pit-defects in GaN-based light-emitting diodes induced by dislocations are considered beneficial to electroluminescence because they relax the strain in InGaN quantum wells and also enhance the hole lateral injection through sidewall of V-pits. In this paper, regularly arranged V-pits are formed on c-plane GaN grown by metal organic vapor phase epitaxy on conventional c-plane cone-patterned sapphire substrates. The size of V-pits and area of flat GaN can be adjusted by changing growth temperature. Five pairs of InGaN/GaN multi-quantumwell and also a light-emitting diode structure are grown o…
Considerable progress has been made in organic light-emitting diodes (OLEDs) to achieve high external quantum efficiency (EQE), among which the dipole orientation of OLED emitters has a remarkable effect. In most cases, EQE of the OLED emitter is theoretically predicted with only one orientation factor to match with corresponding experiments. Here, we develop a distribution theory with three independent parameters to fully describe the relationship between dipole orientations and power densities. Furthermore, we propose an optimal experiment configuration for measuring such distribution parame…
White organic light-emitting diodes (OLEDs) are ultra-thin, large-area light sources made from organic semiconductor materials. Over the last decades, much research has been spent on finding the suitable materials to realize highly efficient monochrome and white OLEDs. With their high efficiency, color-tunability, and color-quality, white OLEDs are emerging to become one of the next generation light sources. In this review, we discuss the physics of a variety of device concepts that are introduced to realize white OLEDs based on both polymer and small molecule organic materi als. Owing to the …
Light-emitting diodes (LEDs) are efficient light sources extensively applied in people's daily life nowadays, with profound effect on their psychological and physiological state subtly and deeply. The correlated color temperature (CCT) the eyes perceive is a key parameter, but the CCT tuning technology of LEDs remains in the development stage. In this study, an electrochromic (EC) material is employed in the tuning device, exhibiting a wide CCT tuning range from 3,200 K to 6,900 K, varying almost along the black-body locus. The driving voltage is lower than 2.4 V, with luminosity loss less tha…
In this paper the design, fabrication and characterization of a bioinspired overlayer deposited on a GaN LED is described. The purpose of this overlayer is to improve light extraction into air from the diode's high refractive-index active material. The layer design is inspired by the microstructure found in the firefly Photuris sp. The actual dimensions and material composition have been optimized to take into account the high refractive index of the GaN diode stack. This two-dimensional pattern contrasts other designs by its unusual profile, its larger dimensions and the fact that it can be t…
We report on the demonstration of the first axial AlInN ultraviolet core-shell nanowire light-emitting diodes with highly stable emission in the UV wavelength range. During the epitaxial growth of AlInN layer, an AlInN shell is spontaneously formed, resulted in the reduced nonradiative recombination on nanowire surface. The AlInN nanowires exhibit high internal quantum efficiency of ~ 52% at room temperature for emission at 295nm. The peak emission wavelength can be varied from 290 nm to 355 nm by changing the growth condition. Moreover, significantly strong transverse magnetic (TM) polarized …
Singlet-polaron and triplet-polaron annihilation mechanisms are the most detrimental exciton quenching processes that lower the efficiency of organic light-emitting diodes (OLEDs) at high current densities, causing so-called efficiency roll-off in these devices. These exciton loss mechanisms are also the critical obstacles towards the realization of electrically pumped organic semiconductor lasers, which require very high current densities to reach threshold. Herein, under a relatively large external magnetic field, we demonstrate that the efficiency roll-off at high current densities in europ…
Perovskite nanoplatelets (NPls) hold great promise for light-emitting applications, having achieved high photoluminescence quantum efficiencies (PLQEs) approaching unity in the blue wavelength range, where other metal-halide perovskites have typically been ineffective. However, the external quantum efficiency (EQE) of blue-emitting NPl light-emitting diodes (LEDs) have only reached 0.12%, with typical values well below 0.1%. In this work, we show that the performance of NPl LEDs is primarily hindered by a poor electronic interface between the emitter and hole-injector. Through Kelvin Probe and…
We report the room-temperature electroluminescence (EL) with nearly pure circular polarization (CP) from GaAs-based spin-polarized light-emitting diodes (spin-LEDs). External magnetic fields are not used during device operation. There are two small schemes in the tested spin-LEDs: firstly, the stripe-laser-like structure that helps intensifying the EL light at the cleaved side walls below the spin injector Fe slab, and secondly, the crystalline AlOx spin tunnel barrier that ensures electrically stable device operation. The purity of CP is depressively low in the low current density (J) region,…
The circular polarization of light scattered by biological tissues provides valuable information and has been considered as a powerful tool for the diagnosis of tumor tissue. We propose a non-staining, non-invasive and in-vivo cancer diagnosis technique using an endoscope equipped with circularly polarized light-emitting diodes (spin-LEDs). We studied the scattering process of the circularly polarized light against cell nuclei in pseudo-healthy and cancerous tissues using the existing Monte Carlo method. The calculation results indicate that the resultant circular polarizations of light scatte…
To improve the light extraction efficiency of organic light emitting diodes (OLEDs), we developed a novel substrate, i.e., a metamaterial based flat Moire micro-lens array formed using double nanoimprint, termed Mlens-array, consisting of a hexagonal moiré pattern pillar array. By choosing a low refractive index dielectric material for the pillar array and a high refractive index dielectric material for the layer capped on top of the pillar array, we fabricated the Mlens-array behaving as a conventional convex optical micro-lens array. The Mlens-array was fabricated on a 4-inch wafer-size glas…
We described an approach to achieve fine color control of fluorescent White Organic Light-Emitting Diodes (OLED), based on an Ultra-thin Premixed emitting Layer (UPL). The UPL consists of a mixture of two dyes (red-emitting 4-di(4'-tert-butylbiphenyl-4-yl)amino-4'-dicyanovinylbenzene or fvin and green-emitting 4-di(4'-tert-butylbiphenyl-4-yl)aminobenzaldehyde or fcho) premixed in a single evaporation cell: since these two molecules have comparable structures and similar melting temperatures, a blend can be evaporated, giving rise to thin films of identical and reproducible composition compared…
Unbalanced charge injection is deleterious for the performance of colloidal quantum dot (CQD) light emitting diodes (LEDs) as it deteriorates the quantum efficiency (QE), brightness and operational lifetime. CQD LEDs emitting in the infrared have previously achieved high quantum efficiencies but only when driven to emit in the low radiance regime. At higher radiance levels, required for practical applications, the efficiency decreased dramatically in view of the notorious efficiency droop. Here we report a novel methodology to regulate charge supply in multinary bandgap CQD composites that fac…
Silicon-based light sources including light-emitting diodes (LEDs) and laser diodes (LDs) for information transmission are urgently needed for developing monolithic integrated silicon photonics. Silicon doped by ion implantation with erbium ions (Er$^{3+}$) is considered a promising approach, but suffers from an extremely low quantum efficiency. Here we report an electrically pumped superlinear emission at 1.54 $μ$m from Er/O-doped silicon planar LEDs, which are produced by applying a new deep cooling process. Stimulated emission at room temperature is realized with a low threshold current of …
Optical detection and spectroscopy of single molecules has become an indispensable tool in biological imaging and sensing. Its success is based on fluorescence of organic dye molecules under carefully engineered laser illumination. In this paper we demonstrate optical detection of single molecules on a wide-field microscope with an illumination based on a commercially available, green light-emitting diode. The results are directly compared with laser illumination in the same experimental configuration. The setup and the limiting factors, such as light transfer to the sample, spectral filtering…
Utilization of triplet excitons, which generally emit poorly, is always fundamental to realize highly efficient organic light-emitting diodes (LEDs). While triplet harvest and energy transfer via electron exchange between triplet donor and acceptor are fully understood in doped organic phosphorescence and delayed fluorescence systems, the utilization and energy transfer of triplet excitons in quasi-two-dimensional (quasi-2D) perovskite are still ambiguous. Here, we use an orange-phosphorescence-emitting ultrathin organic layer to probe triplet behavior in the sky-blue-emitting quasi-2D perovsk…
Quantum-dot light-emitting diodes (QD-LEDs) promise a new generation of efficient, low-cost, large-area, and flexible electroluminescent devices. However, the inferior performance of green and blue QD-LEDs is hindering the commercialization of QD-LEDs in display and solid-state lighting. Here, we demonstrate best-performing green and blue QD-LEDs with ~100% conversion of the injected charge carriers into emissive excitons. Key to this success is eliminating electron leakage at the organic/inorganic interface by using hole-transport polymers with low electron affinity and reduced energetic diso…
Despite widespread interest, ultrathin and highly flexible light-emitting devices that can be seamlessly integrated and used for flexible displays, wearables, and as bioimplants remain elusive. Organic light-emitting diodes (OLEDs) with $μ$m-scale thickness and exceptional flexibility have been demonstrated but show insufficient stability in air and moist environments due to a lack of suitable encapsulation barriers. Here, we demonstrate an efficient and stable OLED with a total thickness of $\approx$12 $μ$m that can be fully immersed in water or cell nutrient media for weeks without suffering…
Quantum sensing and imaging of magnetic fields has attracted broad interests due to its potential for high sensitivity and spatial resolution. Common systems used for quantum sensing require either optical excitation (e.g., nitrogen-vacancy centres in diamond, atomic vapor magnetometers), or cryogenic temperatures (e.g., SQUIDs, superconducting qubits), which pose challenges for chip-scale integration and commercial scalability. Here, we demonstrate an integrated organic light emitting diode (OLED) based quantum sensor for magnetic field imaging, which employs spatially resolved magnetic reson…
In this study, we fabricated hybrid white organic light-emitting diodes (WOLEDs) based on triplet harvesting with simple structure. All the hole transporting material and host in emitting layer (EML) of devices were utilized with same material by using N,N'-di-1-naphthalenyl-N,N'-diphenyl-[1,1':4',1":4",1"'-quaterphenyl]-4,4"'-diamine (4P-NPD) which were known to be blue fluorescent material. Simple hybrid WOLEDs were fabricated three color with blue fluorescent and green, red phosphorescent materials. We was investigated the effect of triplet harvesting (TH) by exciton generation zone on simp…
Surface plasmonic effects of metallic particles have been known to be an effective method to improve the performance light emitting didoes. In this work, we reported the sputtered Au nanoparticles enhanced electroluminescence in inverted quantum dot light emitting diodes (ITO/Au NPs/ZnMgO/QDs/TFB/PEDOT:PSS/Al). By combining the time-resolved photoluminescence, transient electroluminescence and ultraviolet photoelectron spectrometer measurements, the enhancement can be explained to the internal field enhanced exciton coupling to surface plasmons and the increased electron injection rate with Au…
To improve the power efficiency of light emitting diodes (OLEDs), we developed a novel OLED structure, termed Dielectric-Nanomesh OLED (DNM-OLED), fabricated by large-area nanoimprint lithography (NIL). A dielectric-nanomesh substrate with a subwavelength nanomesh grating patterned into glass releases the photons trapped in ITO and organic layers by guided modes into leaky modes. And the dielectric-nanomesh substrate modifies the entire OLED layers into a corrugated configuration, which further lowers the parasitic resistance and hence the operating voltage. For a red phosphorescent OLED in ou…
The quantum efficiency of double hetero-junction light-emitting diodes (LEDs) can be significantly enhanced at low current density by tailoring the spatial profile of dopants to suppress Shockley-Read-Hall (SRH) recombination. To demonstrate this effect we model, design, grow, fabricate, and test a GaInAsP LED ($λ\approx$ 1330nm) with an unconventional dopant profile. Compared against that of our control design, which is a conventional $n^+$-$n$-$p^+$ double hetero-junction LED, the dopant profile near the $n$-$p^+$ hetero-structure of the new design displaces the built-in electric field in su…
Artificial lighting is a widespread technology which consumes large amounts of energy. Triplet-triplet annihilation photochemical upconversion is a method of converting light to a higher frequency. Here, we show theoretically that photochemical upconversion can be applied to Watt-scale lighting, with performance closely approaching the 50% quantum yield upper limit. We describe the dynamic equilibrium of an efficient device consisting of an LED, an upconverting material, and an optical cavity from optical and thermal perspectives.
Intense terahertz (THz) electromagnetic fields have been utilized to reveal a variety of extremely nonlinear optical effects in many materials through nonperturbative driving of elementary and collective excitations. However, such nonlinear photoresponses have not yet been discovered in light-emitting diodes (LEDs), letting alone employing them as fast, cost effective,compact, and room-temperature-operating THz detectors and cameras. Here we report ubiquitously available LEDs exhibited gigantic and fast photovoltaic signals with excellent signal-to-noise ratios when being illuminated by THz fi…
The spectrophotometric characterization of high efficiency, optically-active samples such as light-emitting organic bulks and thin films can be problematic because their broad-band luminescence is detected together with the monochromatic transmitted and reflected signals, hence perturbing measurements of optical transmittance and reflectance at wavelengths within the photoexcitation band. As a matter of fact, most commercial spectrophotometers apply spectral filtering before the light beam reaches the sample, not after it. In this Report, we introduce and discuss the method we have developed t…
We discuss the engineering of p-AlGaN cladding layers for achieving efficient tunnel-injected III-Nitride ultraviolet light emitting diodes (UV LEDs) in the UV-A spectral range. We show that capacitance-voltage measurements can be used to estimate the compensation and doping in p-AlGaN layers located between the multi-quantum well region and the tunnel junction layer. By increasing the p-type doping concentration to overcome the background compensation, on-wafer external quantum efficiency and wall-plug efficiency of 3.37% and 1.62% were achieved for tunnel-injected UV LEDs emitting at 325 nm.…
Lanthanide-based upconversion nanoparticles (UCNPs) generally require high power laser excitation. Here we report wide-field upconversion microscopy at single-nanoparticle sensitivity using incoherent excitation of a 970-nm light-emitting diode (LED). We show that due to its broad emission spectrum, LED excitation is about 3 times less effective for UCNPs and generates high background compared to laser illumination. To counter this, we use time-gated luminescence detection to eliminate the residual background from the LED source, so that individual UCNPs with high sensitizer (Yb3+) doping and …
We investigate a semiconductor $p$-$n$ junction in contact with superconducting leads that is operated under forward bias as a light-emitting diode. The presence of superconductivity results in a significant increase of the electroluminescence in a certain frequency window. We demonstrate that the tunneling of Cooper pairs induces an additional luminescence peak on resonance. There is a transfer of superconducting to photonic coherence which results in the emission of entangled photon pairs and squeezing of the fluctuations in the quadrature amplitudes of the emitted light. The squeezing angle…
The low efficiency of metal halide perovskite light-emitting diodes (PeLEDs) with blue emission block their potential applications in large-area full-color displays and solid-state lighting. A delicate control over the entire electroluminescence process is indispensable to overcome the efficiency limitations of blue PeLEDs. Here, we demonstrate an efficient device architecture to synergistically reduce the energetic losses during electron-photon conversion and boost the extraction of trapped light in the device. An interfacial nucleation seeding scheme is proposed to control the crystallizatio…
