Intelligent reflecting surfaces (IRSs) are a promising technology for enhancing coverage and spectral efficiency, both in the sub-6 GHz and the millimeter wave (mmWave) bands. Existing approaches to leverage the benefits of IRS involve the use of a resource-intensive channel estimation step followed by a computationally expensive algorithm to optimize the reflection coefficients at the IRS. In this work, focusing on the sub-6 GHz band of communications, we present and analyze several alternative schemes, where the phase configuration of the IRS is randomized and multi-user diversity is exploited to opportunistically select the best user at each point in time for data transmission. We show that the throughput of an IRS assisted opportunistic communication (OC) system asymptotically converges to the optimal beamforming-based throughput under fair allocation of resources, as the number of users gets large. We also introduce schemes that enhance the rate of convergence of the OC rate to the beamforming rate with the number of users. For all the proposed schemes, we derive the scaling law of the throughput in terms of the system parameters, as the number of users gets large. Following this, we extend the setup to wideband channels via an orthogonal frequency division multiplexing (OFDM) system and discuss two OC schemes in an IRS assisted setting that clearly elucidate the superior performance that IRS aided OC systems can offer over conventional systems, at very low implementation cost and complexity.
While intelligent reflecting surface (IRS) assisted wireless communication has emerged as an important research paradigm, channel state information (CSI) acquisition remains a critical challenge to design the IRS phase-shifts and yield the promised coherent beamforming gains. In this paper, we propose an IRS-assisted opportunistic beamforming (OBF) scheme under proportional fair scheduling, which does not require instantaneous CSI to design the IRS parameters. In a slow-fading environment, we show that with only random rotations at the IRS, the proposed scheme can capitalize on the multi-user …
This letter aims to clarify the impact of channel aging and phase noise on the performance of intelligent reflecting surface-aided wireless systems. We first model mathematically the outdated channel state information (CSI) due to Doppler shifts and phase noise stemming from hardware impairment. Then, a closed-form expression of achievable spectral efficiency under noisy and aged CSI is theoretically derived. Some typical simulation results to numerically demonstrate the performance impact are illustrated.
Intelligent Reflecting Surface (IRS) has been a promising solution to enhance wireless networks both spectral-efficiently and energy-efficiently. This paper considers an IRS-assisted the Internet of Things network for massive connectivity. We aim to solve the IRS-related activity detection and channel estimation problem which has not been studied before. In this paper, we formulate the IRS-related activity detection and channel estimation problem as sparse matrix factorization, matrix completion and Multiple Measurement Vector problem and, we propose a three-stage framework based on the approx…
With the advancement of sensing technologies over the years, it has become critical to ensure the seamless connectivity of the Internet of Things (IoT) gadgets. With the advancement of communication technology, cellular networks are increasingly being utilized to link IoT systems. An IRS is a rectangular metasurface made up of a vast number of reflecting components that has recently gained research attention due to its ability to significantly improve the energy and spectral efficiencies of communication networks by modifying wireless transmission environments.
Reducing computational complexity is crucial in optimizing the phase shifts of Intelligent Reflecting Surface (IRS) systems since IRS-assisted communication systems are generally deployed with a large number of reflecting elements (REs). This letter proposes a low-complexity algorithm, designated as Dimension-wise Sinusoidal Maximization (DSM), to obtain the optimal IRS phase shifts that maximize the sum capacity of a MIMO network. The algorithm exploits the fact that the objective function for the optimization problem is sinusoidal w.r.t. the phase shift of each RE. The numerical results show…
In this paper, we study the performance of wideband terahertz (THz) communications assisted by an intelligent reflecting surface (IRS). Specifically, we first introduce a generalized channel model that is suitable for electrically large THz IRSs operating in the near-field. Unlike prior works, our channel model takes into account the spherical wavefront of the emitted electromagnetic waves and the spatial-wideband effect. We next show that conventional frequency-flat beamfocusing significantly reduces the power gain due to beam squint, and hence is highly suboptimal. More importantly, we analy…
In this paper, a downlink intelligent reflecting surface (IRS) enhanced millimeter-wave (mmWave) non-orthogonal multiple access (NOMA) system is considered. A joint optimization problem over active beamforming, passive beamforming and power allocation is formulated. Due to the highly coupled variables, the formulated optimization problem is non-convex. To solve this problem, an alternative optimization and successive convex approximation based iterative algorithm is proposed. Numerical results illustrate that: 1) the proposed scheme offers significant sum-rate gains, which confirms the effecti…
Intelligent reflecting surfaces (IRSs) have recently attracted the attention of communication theorists as a means to control the wireless propagation channel. It has been shown that the signal-to-noise ratio (SNR) of a single-user IRS-aided transmission increases as $N^2$, with $N$ being the number of passive reflecting elements in the IRS. This has been interpreted as a major potential advantage of using IRSs, instead of conventional Massive MIMO (mMIMO) whose SNR scales only linearly in $N$. This paper shows that this interpretation is incorrect. We first prove analytically that mMIMO alway…
Rate-splitting multiple access (RSMA) has recently appeared as a powerful technique for improving the downlink performance of multiple-input multiple-output (MIMO) systems. By flexibly managing interference, RSMA can deliver high spectral and energy efficiency, as well as robustness to imperfect channel state information (CSI). In another development, an intelligent reflecting surface (IRS) has emerged as a method to control the wireless environment through software-configurable, near-passive, sub-wavelength reflecting elements. This article presents the potential of synergy between IRS and RS…
Recently, the use of intelligent reflecting surface (IRS) has gained considerable attention in wireless communications. By intelligently adjusting the passive reflection angle, IRS is able to assist the base station (BS) to extend the coverage and improve spectral efficiency. This paper considers a joint symbol-level precoding (SLP) and IRS reflecting design to minimize the symbol-error probability (SEP) of the intended users in an IRS-aided multiuser MISO downlink. We formulate the SEP minimization problems to pursue uniformly good performance for all users for both QAM and PSK constellations…
The operation of an intelligent reflecting surface (IRS) under predictable receiver mobility is investigated. We develop a continuous time system model for multipath channels and discuss the optimal IRS configuration with respect to received power, Doppler spread, and delay spread. It is shown that the received power can be maximized without adding Doppler spread to the system. In a numerical case study, we show that an IRS having the size of just two large billboards can improve the link budget of ground to Low Earth Orbit (LEO) satellite links by up to 6 dB. It also adds a second, almost equ…
In this work, we study the statistically robust beamforming design for an intelligent reflecting surfaces (IRS) assisted multiple-input single-output (MISO) wireless system under imperfect channel state information (CSI), where the channel estimation errors are assumed to be additive Gaussian. We aim at jointly optimizing the transmit/receive beamformers and IRS phase shifts to minimize the average mean squared error (MSE) at the user. In particular, to tackle the non-convex optimization problem, an efficient algorithm is developed by capitalizing on alternating optimization and majorization-m…
Intelligent reflecting surface (IRS) is a new promising technology that is able to manipulate the wireless propagation channel via smart and controllable signal reflection. In this paper, we investigate the capacity region of a multiple access channel (MAC) with two users sending independent messages to an access point (AP), aided by $M$ IRS reflecting elements. We consider two practical IRS deployment strategies that lead to different user-AP effective channels, namely, the distributed deployment where the $M$ reflecting elements form two IRSs, each deployed in the vicinity of one user, versu…
This paper investigates a multiuser downlink communication system with coexisting intelligent reflecting surface (IRS) and classical half-duplex decode-and-forward (DF) relay. In this system, the IRS and the DF relay interact with each other and assist transmission simultaneously. In particular, active beamforming at the base station (BS) and at the DF relay, and passive beamforming at the IRS, are jointly designed to maximize the sum-rate of all users. The sum-rate maximization problem is nonconvex due to the coupled beamforming vectors. We propose an alternating optimization (AO) based algor…
This work proposes linear time strategies to optimally configure the phase shifts for the reflective elements of an intelligent reflecting surface (IRS). Specifically, we show that the binary phase beamforming can be optimally solved in linear time to maximize the received signal-to-noise ratio (SNR). For the general K-ary phase beamforming, we develop a linear time approximation algorithm that guarantees performance within a constant fraction (1+\cos(π/K))/2 of the global optimum, e.g., it can attain over 85% of the optimal performance for the quadrature beamforming with K=4. According to the…
This paper investigates a device-to-device (D2D) cooperative computing system, where an user can offload part of its computation task to nearby idle users with the aid of an intelligent reflecting surface (IRS). We propose to minimize the total computing delay via jointly optimizing the computation task assignment, transmit power, bandwidth allocation, and phase beamforming of the IRS. To solve the formulated problem, we devise an alternating optimization algorithm with guaranteed convergence. In particular, the task assignment strategy is derived in closed-form expression, while the phase bea…
Recently, the hybrid relay-reflecting intelligent surface (HRRIS) has been introduced as a spectral- and energy-efficient architecture to assist wireless communication systems. In the HRRIS, a single or few active relay elements are deployed along with a large number of passive reflecting elements, allowing it to not only reflect but also amplify the incident signals. In this work, we investigate the potential of the HRRIS in aiding the computation offloading in a single-user mobile edge computing system. The objective is to minimize the offloading latency while ensuring the secrecy of user da…
Intelligent reflecting surfaces (IRSs) are regarded as promising enablers for future millimeter wave (mmWave) wireless communication, due to their ability to create favorable line-of-sight (LoS) propagation environments. In this paper, we investigate channel estimation in downlink IRS-assisted mmWave multiple-input multiple-output (MIMO) systems. By leveraging the sparsity of mmWave channels, we formulate the channel estimation problem as a fixed-rank constrained non-convex optimization problem. To tackle the non-convexity, an efficient algorithm is proposed by capitalizing on alternating mini…
Intelligent reflecting surface (IRS) has recently received much attention from the research community due to its potential to achieve high spectral and power efficiency cost-effectively. In addition to traditional cellular networks, the use of IRS in vehicular networks is also considered. Prior works on IRS-aided vehicle-to-everything communications focus on deploying reflection surfaces on the facades of buildings along the road for sidelink performance enhancement. This paper goes beyond the state of the art by presenting a novel paradigm coined Intelligent Reflecting Vehicle Surface (IRVS).…
The promising coverage and spectral efficiency gains of intelligent reflecting surfaces (IRSs) are attracting increasing interest. In order to realize these surfaces in practice, however, several challenges need to be addressed. One of these main challenges is how to configure the reflecting coefficients on these passive surfaces without requiring massive channel estimation or beam training overhead. Earlier work suggested leveraging supervised learning tools to design the IRS reflection matrices. While this approach has the potential of reducing the beam training overhead, it requires collect…
This paper proposes a novel location information aided multiple intelligent reflecting surface (IRS) systems. Assuming imperfect user location information, the effective angles from the IRS to the users are estimated, which is then used to design the transmit beam and IRS beam. Furthermore, closed-form expressions for the achievable rate are derived. The analytical findings indicate that the achievable rate can be improved by increasing the number of base station (BS) antennas or reflecting elements. Specifically, a power gain of order $N M^2$ is achieved, where $N$ is the antenna number and $…
This paper considers an intelligent reflecting surface (IRS) aided multiple-input single-output communication system, where statistical channel state information (CSI) is exploited for transmit beamforming and IRS beamforming. A tight upper bound is derived for the ergodic capacity of the system. Based on which, the joint optimization of transmit beam and IRS beam are studied. Depending on whether a line-of-sight path exists between the access point and user, two different cases, namely, Rician fading and Rayleigh fading, are separately treated. Specifically, for the Rician fading case, an ite…
Intelligent reflecting surface (IRS) is a cost-efficient technique to improve power efficiency and spectral efficiency. However, IRS-aided multi-antenna transmission needs to jointly optimize the passive and active beamforming, imposing a high computational burden and high latency due to its iterative optimization process. Making use of hybrid analog-digital beamforming in high-frequency transmission systems, a novel technique, coined dual-beam IRS, is proposed in this paper. The key idea is to form a pair of beams towards the IRS and user, respectively. Then, the optimization of passive and a…
This letter focuses on the secure transmission for an intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) and terahertz (THz) systems, in which a base station (BS) communicates with its destination via an IRS, in the presence of a passive eavesdropper. To maximize the system secrecy rate, the transmit beamforming at the BS and the reflecting matrix at the IRS are jointly optimized with transmit power and discrete phase-shift constraints. It is first proved that the beamforming design is independent of the phase shift design under the rank-one channel assumption. The formulat…
Intelligent reflecting surface (IRS)-assisted wireless communication is widely deemed a key technology for 6G systems. The main challenge in deploying an IRS-aided terahertz (THz) link, though, is the severe propagation losses at high frequency bands. Hence, a THz IRS is expected to consist of a massive number of reflecting elements to compensate for those losses. However, as the IRS size grows, the conventional far-field assumption starts becoming invalid and the spherical wavefront of the radiated waves must be taken into account. In this work, we focus on the near-field and analytically det…
Intelligent reflecting surfaces (IRSs) can be beneficial to both information and energy transfer, due to the gains achieved by their multiple elements. In this work, we deal with the impact of spatial correlation between the IRS elements, in the context of simultaneous wireless information and power transfer. The performance is evaluated in terms of the average harvested energy and the outage probability for random and equal phase shifts. Closed-form analytical expressions for both metrics under spatial correlation are derived. Moreover, the optimal case is considered when the elements are unc…
An intelligent reflecting surface (IRS) can greatly improve the channel quality over a frequency-flat channel, if it is configured to reflect the incident signal as a beam towards the receiver. However, the fundamental limitations of the IRS technology become apparent over practical frequency-selective channels, where the same configuration must be used over the entire bandwidth. In this paper, we consider a wideband orthogonal frequency-division multiplexing (OFDM) system that is supported by a fairly realistic IRS setup with two unbalanced states per element and also mutual coupling. We desc…
Intelligent reflecting surface (IRS) has become a promising technology to aid next generation wireless communication systems. In this paper, we develop an alternating beamforming technique with a novel concept of IRS element allocation for multiple-input multiple-output systems when a base station supports multiple single antenna users aided with a single IRS. Specifically, we allocate each IRS element separately to each user, thus, in the beamforming stage allowing the IRS element only consider a single user at a time. In result to this separation, the complexity is vastly decreased. The prop…
In this paper, we propose a novel encrypted data transmission scheme using an intelligent reflecting surface (IRS) to generate secret keys in wireless communication networks. We show that perfectly secure one-time pad (OTP) communications can be established by using a simple random phase shifting of the IRS elements. To maximize the secure transmission rate, we design an optimal time slot allocation algorithm for the IRS secret key generation and the encrypted data transmission phases. Moreover, a theoretical expression of the key generation rate is derived based on Poisson point process (PPP)…
This paper investigates the achievable rate region of the multiple-input single-output (MISO) interference channel aided by intelligent reflecting surfaces (IRSs). We exploit the the additional design degree of freedom provided by the coordinated IRSs to enhance the desired signal and suppress interference so as to enlarge the achievable rate region of the interference channel. To this end, we jointly optimize the active transmit beamforming at the transmitters and passive reflective beamforming at the IRSs, subject to the constant modulus constraints of reflective beamforming vectors. To addr…
The intelligent reflecting surface (IRS) is a planar array with massive reconfigurable passive elements, which can align the reflecting signals at the receivers via controlling the phase shifts at each element independently. Since IRS can be implemented without RF chain, it is seen as a cost-effective solution for boosting the spectral efficiency for the future communication system. This work considers the IRS-aided multiuser multi-input single-output downlink transmission, and our goal is to maximize the sum rate by jointly optimizing the transmit beamformer at the base station and the phase …
Intelligent reflecting surface (IRS) is a proposing technology in 6G to enhance the performance of wireless networks by smartly reconfiguring the propagation environment with a large number of passive reflecting elements. However, current works mainly focus on single IRS-empowered wireless networks, where the channel rank deficiency problem has emerged. In this paper, we propose a distributed IRS-empowered communication network architecture, where multiple source-destination pairs communicate through multiple distributed IRSs. We further contribute to maximize the achievable sum-rates in this …
An intelligent reflecting surface (IRS) is an array of discrete elements with configurable scattering properties. It has the capability to beamform arriving radio waves to an intended receiver, making it an attractive candidate technology for fifth-generation (5G) communications. A recent study debunked the notion that IRSs can replace relays because a large number of IRS elements is required even to approach the performance of simple single-antenna decode-and-forward (DF) relays. The study introduced 4G channel models into a theoretical framework to obtain simulation results, based on which c…
Intelligent reflecting surfaces (IRSs) have received much attention recently and are envisioned to promote 6G communication networks. In this paper, for wireless communications aided by IRS units, we formulate optimization problems for power control under quality of service (QoS) and max-min fair QoS under three kinds of traffic patterns from a base station (BS) to mobile users (MUs): unicast, broadcast, and multicast. The optimizations are achieved by jointly designing the transmit beamforming of the BS and the phase shift matrix of the IRS. For power control under QoS, existing IRS studies i…
Wireless communications via intelligent reflecting surfaces (IRSs) has received considerable attention from both academia and industry. In particular, IRSs are able to create favorable wireless propagation environments with typically low-cost passive devices. While various IRS-aided wireless communication systems have been investigated in the literature, thus far, the optimal design of such systems is not well understood. In this paper, IRS-assisted single-user multiple-input single-output (MISO) communication is investigated. To maximize the spectral efficiency, a branch-and-bound (BnB) algor…
Over-the-air computation (AirComp) becomes a promising approach for fast wireless data aggregation via exploiting the superposition property in a multiple access channel. To further overcome the unfavorable signal propagation conditions for AirComp, in this paper, we propose an intelligent reflecting surface (IRS) aided AirComp system to build controllable wireless environments, thereby boosting the received signal power significantly. This is achieved by smartly tuning the phase shifts for the incoming electromagnetic waves at IRS, resulting in reconfigurable signal propagations. Unfortunatel…
Unmanned Aerial Vehicles (UAV)-enabled communication is a promising solution for secure air-to-ground (A2G) networks due to the additional secure degrees of freedom afforded by mobility. However, the jittering characteristics caused by the random airflow and the body vibration of the UAV itself have a non-negligible impact on the performance of UAV communication. Considering the impact of UAV jittering, this paper propose a robust and secure transmission design assisted by an novel active intelligent reflecting surface (IRS),where the reflecting elements in IRS not only adjust the phase shift …
We introduce a novel system setup where a backscatter device operates in the presence of an intelligent reflecting surface (IRS). In particular, we study the bistatic backscatter communication (BackCom) system assisted by an IRS. The phase shifts at the IRS are optimized jointly with the transmit beamforming vector of the carrier emitter to minimize the transmit power consumption at the carrier emitter whilst guaranteeing a required BackCom performance. The unique channel characteristics arising from multiple reflections at the IRS render the optimization problem highly non-convex. Therefore, …
As communication systems that employ millimeter wave (mmWave) frequency bands must use large antenna arrays to overcome the severe propagation loss of mmWave signals, hybrid beamforming has been considered as an integral component of mmWave communications. Recently, intelligent reflecting surface (IRS) has been proposed as an innovative technology that can significantly improve the performance of mmWave communication systems through the use of low-cost passive reflecting elements. In this paper, we study IRS-aided mmWave multiple-input multiple-output (MIMO) systems with hybrid beamforming arc…
In this letter, we study a rate-splitting multiple access (RSMA)-based intelligent reflecting surface (IRS)-aided multi-user multiple-input single-output (MISO) secure communication system with a potential eavesdropper (Eve). Aiming to maximize the minimum secrecy rate (SR) among all the legitimate users (LUs), a design problem for jointly optimizing the transmit beamforming with artificial noise (AN), the IRS beamforming, and the secrecy common rate allocation is formulated. Since the design problem is highly non-convex with coupled optimization variables, we develop a computationally efficie…
Cell-free massive multiple-input multiple-output (MIMO) and intelligent reflecting surface (IRS) are considered as the prospective multiple antenna technologies for beyond the fifth-generation (5G) networks. Cell-free MIMO systems powered by IRSs, combining both technologies, can further improve the performance of cell-free MIMO systems at low cost and energy consumption. Prior works focused on instantaneous performance metrics and relied on alternating optimization algorithms, which impose huge computational complexity and signaling overhead. To address these challenges, we propose a novel tw…
An intelligent reflecting surface (IRS), consisting of reconfigurable metamaterials, can be used to partially control the radio environment and thereby bring new features to wireless communications. Previous works on IRS have particularly studied the range extension use case and under what circumstances the new technology can beat relays. In this paper, we study another use case that might have a larger impact on the channel capacity: rank improvement. One of the classical bottlenecks of point-to-point MIMO communications is that the capacity gains provided by spatial multiplexing are only lar…
In this paper, we consider covert beamforming design for intelligent reflecting surface (IRS) assisted Internet of Things (IoT) networks, where Alice utilizes IRS to covertly transmit a message to Bob without being recognized by Willie. We investigate the joint beamformer design of Alice and IRS to maximize the covert rate of Bob when the knowledge about Willie's channel state information (WCSI) is perfect and imperfect at Alice, respectively. For the former case, we develop a covert beamformer under the perfect covert constraint by applying semidefinite relaxation. For the later case, the opt…
Intelligent reflecting surface (IRS) is an emerging technology that is able to significantly improve the performance of wireless communications, by smartly tuning signal reflections at a large number of passive reflecting elements. On the other hand, with ubiquitous wireless devices and ambient radio-frequency signals, wireless sensing has become a promising new application for the next-generation/6G wireless networks. By synergizing low-cost IRS and fertile wireless sensing applications, this article proposes a new IRS-aided sensing paradigm for enhancing the performance of wireless sensing c…
Multi-user (MU) diversity yields sum-rate gains by scheduling a user for transmission at times when its channel is near its peak. The only information required at the base station (BS) for scheduling is the users' signal-to-noise ratios (SNR)s. MU diversity gains are limited in environments with line-of-sight (LoS) channel components and/or spatial correlation. To remedy this, previous works have proposed opportunistic beamforming (OBF) using multiple antennas at the BS to transmit the same signal, modulated by time-varying gains, to the best user at each time slot. In this paper, we propose r…
Intelligent reflecting surfaces (IRSs) are regarded as key enablers of next-generation wireless communications, due to their capability of customizing the wireless propagation environment. In this paper, we investigate power-efficient resource allocation for IRS-assisted multiuser multiple-input single-output (MISO) systems. To minimize the transmit power, both the beamforming vectors at the access point (AP) and phase shifts at the IRS are jointly optimized while taking into account the minimum required quality-of-service (QoS) of the users. To tackle the non-convexity of the formulated optim…
In this letter, the achievable rate maximization problem is considered for intelligent reflecting surface (IRS) assisted multiple-input multiple-output (MIMO) systems in an underlay spectrum sharing scenario, subject to interference power constraints at the primary users. The formulated non-convex optimization problem is challenging to solve due to its non-convexity as well as coupling design variables in the constraints. Different from existing works that are mostly based on alternating optimization (AO), we propose a penalty dual decomposition based gradient projection (PDDGP) algorithm to s…
This paper proposes a novel framework of resource allocation in intelligent reflecting surface (IRS) aided multi-cell non-orthogonal multiple access (NOMA) networks, where a sum-rate maximization problem is formulated. To address this challenging mixed-integer non-linear problem, we decompose it into an optimization problem (P1) with continuous variables and a matching problem (P2) with integer variables. For the non-convex optimization problem (P1), iterative algorithms are proposed for allocating transmit power, designing reflection matrix, and determining decoding order by invoking relaxati…
In this paper, channel estimation techniques and phase shift design for intelligent reflecting surface (IRS)-empowered single-user multiple-input multiple-output (SU-MIMO) systems are proposed. Among four channel estimation techniques developed in the paper, the two novel ones, single-path approximated channel (SPAC) and selective emphasis on rank-one matrices (SEROM), have low training overhead to enable practical IRS-empowered SU-MIMO systems. SPAC is mainly based on parameter estimation by approximating IRS-related channels as dominant single-path channels. SEROM exploits IRS phase shifts a…
Terahertz (THz) and intelligent reflecting surface (IRS) have been regarded as two promising technologies to improve the capacity and coverage for future 6G networks. Generally, IRS is usually equipped with large-scale elements when implemented at THz frequency. In this case, the near-field model and beam squint should be considered. Therefore, in this paper, we investigate the far-field and near-field beam squint problems in THz IRS communications for the first time. The far-field and near-field channel models are constructed based on the different electromagnetic radiation characteristics. N…
In this paper, we propose a fairness-aware rate maximization scheme for a wireless powered communications network (WPCN) assisted by an intelligent reflecting surface (IRS). The proposed scheme combines user scheduling based on time division multiple access (TDMA) and (mechanical) angular displacement of the IRS. Each energy harvesting user (EHU) has dedicated time slots with optimized durations for energy harvesting and information transmission whereas, the phase matrix of the IRS is adjusted to focus its beam to a particular EHU. The proposed scheme exploits the fundamental dependence of the…
The performance of a device-to-device (D2D) underlay communication system is limited by the co-channel interference between cellular users (CUs) and D2D devices. To address this challenge, an intelligent reflecting surface (IRS) aided D2D underlay system is studied in this paper. A two-timescale optimization scheme is proposed to reduce the required channel training and feedback overhead, where transmit beamforming at the base station (BS) and power control at the D2D transmitter are adapted to instantaneous effective channel state information (CSI); and the IRS phase shifts are adapted to slo…
