The performance of a device-to-device (D2D) underlay communication system is limited by the co-channel interference between cellular users (CUs) and D2D devices. To address this challenge, an intelligent reflecting surface (IRS) aided D2D underlay system is studied in this paper. A two-timescale optimization scheme is proposed to reduce the required channel training and feedback overhead, where transmit beamforming at the base station (BS) and power control at the D2D transmitter are adapted to instantaneous effective channel state information (CSI); and the IRS phase shifts are adapted to slow-varying channel mean. Based on the two-timescale optimization scheme, we aim to maximize the D2D ergodic rate subject to a given outage probability constrained signal-to-interference-plus-noise ratio (SINR) target for the CU. The two-timescale problem is decoupled into two sub-problems, and the two sub-problems are solved iteratively with closed-form expressions. Numerical results verify that the two-timescale based optimization performs better than several baselines, and also demonstrate a favorable trade-off between system performance and CSI overhead.
In this letter, the achievable rate maximization problem is considered for intelligent reflecting surface (IRS) assisted multiple-input multiple-output (MIMO) systems in an underlay spectrum sharing scenario, subject to interference power constraints at the primary users. The formulated non-convex optimization problem is challenging to solve due to its non-convexity as well as coupling design variables in the constraints. Different from existing works that are mostly based on alternating optimization (AO), we propose a penalty dual decomposition based gradient projection (PDDGP) algorithm to s…
In this paper, we investigate the performance of a three-node dual-hop cognitive radio network (CRN) with a half-duplex (HD) decode-and-forward (DF) buffer-aided relay. We derive expressions for the average rate and symbol error rate (SER) performance of an adaptive link selection based channel-aware buffer-aided relay (CABR) scheme that imposes peak-power and peak-interference constraints on the secondary nodes, and compare them with those of conventional non-buffer-aided relay (CNBR) and conventional buffer-aided relay (CBR) schemes for a delay-tolerant system. For finite-delay systems, we a…
In this paper, a buffered decode and forward (DF) relay based three-node underlay cooperative cognitive relay network (CRN) is considered with a direct path to the destination. The source and the relay use multiple rates, and joint rate and link selection are performed to maximize throughput. Optimum link and rate selection rules are evolved that ensure buffer stability, and expressions are derived for the throughput assuming peak power and peak interference constraints on the transmit power of the secondary nodes. The expressions are written in a manner that yields useful insights on buffer s…
Joint 3D Trajectory Design and Resource Allocation for Secure Dual-UAV-aided Underlay Systems
Chongqing University of Posts and Telecommunications（重庆邮电大学）；King Abdullah University of Science and Technology (KAUST)（阿卜杜拉国王科技大学）；Sun Yat-sen University（中山大学）；Beijing Institute of Technology（北京理工大学）
Device-to-device (D2D) communication in cellular networks allows direct transmission between two cellular devices with local communication needs. Due to the increasing number of autonomous heterogeneous devices in future mobile networks, an efficient resource allocation scheme is required to maximize network throughput and achieve higher spectral efficiency. In this paper, performance of network-integrated D2D communication under channel uncertainties is investigated where D2D traffic is carried through relay nodes. Considering a multi-user and multi-relay network, we propose a robust distribu…
In this paper, we study the performance of wideband terahertz (THz) communications assisted by an intelligent reflecting surface (IRS). Specifically, we first introduce a generalized channel model that is suitable for electrically large THz IRSs operating in the near-field. Unlike prior works, our channel model takes into account the spherical wavefront of the emitted electromagnetic waves and the spatial-wideband effect. We next show that conventional frequency-flat beamfocusing significantly reduces the power gain due to beam squint, and hence is highly suboptimal. More importantly, we analy…
Reducing computational complexity is crucial in optimizing the phase shifts of Intelligent Reflecting Surface (IRS) systems since IRS-assisted communication systems are generally deployed with a large number of reflecting elements (REs). This letter proposes a low-complexity algorithm, designated as Dimension-wise Sinusoidal Maximization (DSM), to obtain the optimal IRS phase shifts that maximize the sum capacity of a MIMO network. The algorithm exploits the fact that the objective function for the optimization problem is sinusoidal w.r.t. the phase shift of each RE. The numerical results show…
Intelligent reflecting surface (IRS) is a new promising technology that is able to manipulate the wireless propagation channel via smart and controllable signal reflection. In this paper, we investigate the capacity region of a multiple access channel (MAC) with two users sending independent messages to an access point (AP), aided by $M$ IRS reflecting elements. We consider two practical IRS deployment strategies that lead to different user-AP effective channels, namely, the distributed deployment where the $M$ reflecting elements form two IRSs, each deployed in the vicinity of one user, versu…
This paper investigates the achievable rate region of the multiple-input single-output (MISO) interference channel aided by intelligent reflecting surfaces (IRSs). We exploit the the additional design degree of freedom provided by the coordinated IRSs to enhance the desired signal and suppress interference so as to enlarge the achievable rate region of the interference channel. To this end, we jointly optimize the active transmit beamforming at the transmitters and passive reflective beamforming at the IRSs, subject to the constant modulus constraints of reflective beamforming vectors. To addr…
This paper proposes a novel location information aided multiple intelligent reflecting surface (IRS) systems. Assuming imperfect user location information, the effective angles from the IRS to the users are estimated, which is then used to design the transmit beam and IRS beam. Furthermore, closed-form expressions for the achievable rate are derived. The analytical findings indicate that the achievable rate can be improved by increasing the number of base station (BS) antennas or reflecting elements. Specifically, a power gain of order $N M^2$ is achieved, where $N$ is the antenna number and $…
Intelligent reflecting surface (IRS) is an emerging technology that is able to significantly improve the performance of wireless communications, by smartly tuning signal reflections at a large number of passive reflecting elements. On the other hand, with ubiquitous wireless devices and ambient radio-frequency signals, wireless sensing has become a promising new application for the next-generation/6G wireless networks. By synergizing low-cost IRS and fertile wireless sensing applications, this article proposes a new IRS-aided sensing paradigm for enhancing the performance of wireless sensing c…
Intelligent reflecting surface (IRS) has the potential to significantly enhance the network performance by reconfiguring the wireless propagation environments. It is however difficult to obtain the accurate downlink channel state information (CSI) for efficient beamforming design in IRS-aided wireless networks. In this article, we consider an IRS-aided downlink multiple-input single-output (MISO) network, where the base station (BS) is not required to know the underlying channel distribution. We formulate an outage probability minimization problem by jointly optimizing the beamforming vector a…
In this letter, we study a rate-splitting multiple access (RSMA)-based intelligent reflecting surface (IRS)-aided multi-user multiple-input single-output (MISO) secure communication system with a potential eavesdropper (Eve). Aiming to maximize the minimum secrecy rate (SR) among all the legitimate users (LUs), a design problem for jointly optimizing the transmit beamforming with artificial noise (AN), the IRS beamforming, and the secrecy common rate allocation is formulated. Since the design problem is highly non-convex with coupled optimization variables, we develop a computationally efficie…
As communication systems that employ millimeter wave (mmWave) frequency bands must use large antenna arrays to overcome the severe propagation loss of mmWave signals, hybrid beamforming has been considered as an integral component of mmWave communications. Recently, intelligent reflecting surface (IRS) has been proposed as an innovative technology that can significantly improve the performance of mmWave communication systems through the use of low-cost passive reflecting elements. In this paper, we study IRS-aided mmWave multiple-input multiple-output (MIMO) systems with hybrid beamforming arc…
This paper considers an active intelligent reflecting surface (IRS)-aided wireless powered communication network (WPCN), where devices first harvest energy and then transmit information to a hybrid access point (HAP). Different from the existing works on passive IRS-aided WPCNs, this is the first work that introduces the active IRS in WPCNs. To guarantee fairness, the problem is formulated as an amplifying power-limited weighted sum throughput (WST) maximization problem, which is solved by successive convex approximation technique and fractional programming alternatively. To balance the perfor…
In this paper, the novel simultaneously transmitting and reflecting (STAR) reconfigurable intelligent surface (RIS), which enables full-space coverage on users located on both sides of the surface, is investigated in the multi-user mobile edge computing (MEC) system. A computation rate maximization problem is formulated via the joint design of the STAR-RIS phase shifts, reflection and transmission amplitude coefficients, the receive beamforming vectors at the access point, and the users' energy partition strategies for local computing and offloading. Two operating protocols of STAR-RIS, namely…
This paper considers a two-user downlink transmission in intelligent reflecting surface (IRS) aided network over fading channels. Particularly, non-orthogonal multiple access (NOMA) and two orthogonal multiple access (OMA) schemes, namely, time division multiple access (TDMA) and frequency division multiple access (FDMA), are studied. The objective is to maximize the system average sum rate for the delay-tolerant transmission. We propose two adjustment schemes, namely, dynamic phase adjustment and one-time phase adjustment. The power budget, minimum average data rate, and discrete unit modulus…
This paper proposes a novel framework of resource allocation in intelligent reflecting surface (IRS) aided multi-cell non-orthogonal multiple access (NOMA) networks, where a sum-rate maximization problem is formulated. To address this challenging mixed-integer non-linear problem, we decompose it into an optimization problem (P1) with continuous variables and a matching problem (P2) with integer variables. For the non-convex optimization problem (P1), iterative algorithms are proposed for allocating transmit power, designing reflection matrix, and determining decoding order by invoking relaxati…
Underlay cognitive radios (UCRs) allow a secondary user to enter a primary user's spectrum through intelligent utilization of multiuser channel quality information (CQI) and sharing of codebook. The aim of this work is to study two-user Gaussian UCR systems by assuming the full or partial knowledge of multiuser CQI. Key contribution of this work is motivated by the fact that the full knowledge of multiuser CQI is not always available. We first establish a location-aided UCR model where the secondary user is assumed to have partial CQI about the secondary-transmitter to primary-receiver link as…
We consider in this paper a new intelligent reflecting surface (IRS)-aided LEO satellite communication system, by utilizing the controllable phase shifts of massive passive reflecting elements to achieve flexible beamforming, which copes with the time-varying channel between the high-mobility satellite (SAT) and ground node (GN) cost-effectively. In particular, we propose a new architecture for IRS-aided LEO satellite communication where IRSs are deployed at both sides of the SAT and GN, and study their cooperative passive beamforming (CPB) design over line-of-sight (LoS)-dominant single-refle…
In this letter, we consider an intelligent reflecting surface (IRS)-aided wireless relaying system, where a decode-and-forward relay (R) is employed to forward data from a source (S) to a destination (D), aided by M passive reflecting elements. We consider two practical IRS deployment strategies, namely, single-IRS deployment where all reflecting elements are mounted on one single IRS that is deployed near S, R, or D, and multi-IRS deployment where the reflecting elements are allocated over three separate IRSs which are deployed near S, R, and D, respectively. Under the line-of-sight (LoS) cha…
As a recently proposed idea for future wireless systems, intelligent reflecting surface (IRS) can assist communications between entities which do not have high-quality direct channels in between. Specifically, an IRS comprises many low-cost passive elements, each of which reflects the incident signal by incurring a phase change so that the reflected signals add coherently at the receiver. In this paper, for an IRS-aided wireless network, we study the problem of power control at the base station (BS) for physical-layer broadcasting under quality of service (QoS) constraints at mobile users, by …
This letter presents a detailed performance analysis of the intelligent reflecting surface (IRS) aided single-input single-output communication systems, taking into account of the direct link between the transmitter and receiver. A closed-form upper bound is derived for the ergodic capacity, and an accurate approximation is obtained for the outage probability. In addition, simplified expressions are presented in the asymptotic regime. Numerical results are provided to validate the correctness of the theoretical analysis. It is found that increasing the number of reflecting elements can signifi…
This letter investigates physical layer security in intelligent reflecting surface (IRS)-aided visible light communication (VLC). Under the point source assumption, we first elaborate the system model in the scenario with multiple legitimate users and one eavesdropper, where the secrecy rate maximization problem is transformed into an assignment problem by objective function approximation. Then, an iterative Kuhn-Munkres algorithm is proposed to optimize the transformed problem, and its computational complexity is in the second-order form of the numbers of IRS units and transmitters. Moreover,…
This work studies the modelling and the optimization of intelligent reflecting surface (IRS) assisted multiple-input multiple-output (MIMO) systems through cascaded line-of-sight (LoS) links. In Part I of this work, we build up a new IRS-aided MIMO channel model, named the cascaded LoS MIMO channel. The proposed channel model consists of a transmitter (Tx) and a receiver (Rx) both equipped with uniform linear arrays, and an IRS is used to enable communications between the transmitter and the receiver through the LoS links seen by the IRS. When modeling the reflection of electromagnetic waves a…
We introduce a novel system setup where a backscatter device operates in the presence of an intelligent reflecting surface (IRS). In particular, we study the bistatic backscatter communication (BackCom) system assisted by an IRS. The phase shifts at the IRS are optimized jointly with the transmit beamforming vector of the carrier emitter to minimize the transmit power consumption at the carrier emitter whilst guaranteeing a required BackCom performance. The unique channel characteristics arising from multiple reflections at the IRS render the optimization problem highly non-convex. Therefore, …
In this paper, we investigate the design of robust and secure transmission in intelligent reflecting surface (IRS) aided wireless communication systems. In particular, a multi-antenna access point (AP) communicates with a single-antenna legitimate receiver in the presence of multiple single-antenna eavesdroppers, where the artificial noise (AN) is transmitted to enhance the security performance. Besides, we assume that the cascaded AP-IRS-user channels are imperfect due to the channel estimation error. To minimize the transmit power, the beamforming vector at the transmitter, the AN covariance…
Intelligent reflecting surface (IRS) is a promising solution to enhance the wireless communication capacity both cost-effectively and energy-efficiently, by properly altering the signal propagation via tuning a large number of passive reflecting units. In this paper, we aim to characterize the fundamental capacity limit of IRS-aided point-to-point multiple-input multiple-output (MIMO) communication systems with multi-antenna transmitter and receiver in general, by jointly optimizing the IRS reflection coefficients and the MIMO transmit covariance matrix. First, we consider narrowband transmiss…
Intelligent Reflecting Surface (IRS) has been recently proposed as a promising solution to enhance the spectral and energy efficiency of future wireless networks by tuning a massive number of low-cost passive reflecting elements and thereby constructing favorable wireless propagation environment. Different from the prior works that focus on link-level performance optimization for IRS-aided wireless systems, this letter characterizes the spatial throughput of a single-cell multiuser system aided by multiple IRSs that are randomly deployed in the cell. It is shown by simulation that our analysis…
We propose a novel design of a dual-function radar communication (DFRC) system aided by an Intelligent Reflecting Surface (IRS). We consider a scenario with one target and multiple communication receivers, where there is no line-of-sight between the radar and the target. The radar precoding matrix and the IRS weights are optimally designed to maximize the weighted sum of the signal-to-noise ratio (SNR) at the radar receiver and the SNR at the communication receivers subject to power constraints and constant modulus constraints on the IRS weights. The problem is decoupled into two sub-problems,…
In this letter, we investigate the robust and secure beamforming (RSBF) in an intelligent reflecting surface (IRS) aided millimeter wave (mmWave) multiple input single output (MISO) system, where multiple single antenna eavesdroppers (Eves) are arbitrarily distributed nearby the legitimate receiver. Considering the channel state information (CSI) of Eves' channels is imperfectly known at the legitimate transmitter, the RSBF design problems to maximize the worst case of achievable secrecy rate (ASR) are formulated under the total transmission power and unit-modulus constraints. Since the proble…
This letter investigates the joint active and passive beamforming optimization for intelligent reflecting surface (IRS) aided multiuser multiple-input multiple-output systems with the objective of maximizing the weighted sum-rate. We show that this problem can be solved via a matrix weighted mean square error minimization equivalence. In particular, for the optimization of the passive IRS beamforming, we first propose an iterative algorithm with excellent performance based on the manifold optimization. By using the matrix fractional programming technique to obtain a more tractable object funct…
This paper considers a MIMO secure wireless communication system aided by the physical layer security technique of sending artificial noise (AN). To further enhance the system security performance, the advanced intelligent reflecting surface (IRS) is invoked in the AN-aided communication system, where the base station (BS), legitimate information receiver (IR) and eavesdropper (Eve) are equipped with multiple antennas. With the aim for maximizing the secrecy rate (SR), the transmit precoding (TPC) matrix at the BS, covariance matrix of AN and phase shifts at the IRS are jointly optimized subje…
Intelligent reflecting surface (IRS) has emerged as a promising technique for wireless communication networks. By dynamically tuning the reflection amplitudes/phase shifts of a large number of passive elements, IRS enables flexible wireless channel control and configuration, and thereby enhances the wireless signal transmission rate and reliability significantly. Despite the vast literature on designing and optimizing assorted IRS-aided wireless systems, prior works have mainly focused on enhancing wireless links with single signal reflection only by one or multiple IRSs, which may be insuffic…
In this paper, we study the waveform and passive beamforming design for intelligent reflecting surface (IRS)-aided wireless power transfer (WPT). Generalized multi-user and low complexity single-user algorithms are derived based on alternating optimization (AO) framework to maximize the weighted sum output DC current, subject to transmit power constraints and passive beamforming phases unit modulus constraints. The input signal waveform and IRS passive beamforming phase shifts are jointly designed as a function of users' individual frequency-selective channel state information (CSI). The energ…
Reconfigurable intelligent surface (RIS) provides a promising way to build the programmable wireless transmission environments in the future. Owing to the large number of reflecting elements used at the RIS, joint optimization for the active beamforming at the transmitter and the passive reflector at the RIS is usually complicated and time-consuming. To address this problem, this paper proposes a low-complexity joint beamforming and reflecting algorithm based on fractional programing (FP). Specifically, we first consider a RIS-aided multi-user communication system with perfect channel state in…
Channel estimation is a practical challenge for intelligent reflecting surface (IRS) aided wireless communication. As the number of IRS reflecting elements or IRS-aided users increases, the channel training overhead becomes excessively high, which results in long delay and low throughput in data transmission. To tackle this challenge, we propose in this paper a new anchor-assisted channel estimation approach, where two anchor nodes, namely A1 and A2, are deployed near the IRS for facilitating its aided base station (BS) in acquiring the cascaded BS-IRS-user channels required for data transmiss…
This paper investigates intelligent reflecting surface (IRS)-aided multicell wireless networks, where an IRS is deployed to assist the joint processing coordinated multipoint (JP-CoMP) transmission from multiple base stations (BSs) to multiple cell-edge users. By taking into account the fairness among cell-edge users, we aim at maximizing the minimum achievable rate of cell-edge users by jointly optimizing the transmit beamforming at the BSs and the phase shifts at the IRS. As a compromise approach, we transform the non-convex max-min problem into an equivalent form based on the mean-square er…
Spectrum sensing is a key enabling technique for cognitive radio (CR), which provides essential information on the spectrum availability. However, due to severe wireless channel fading and path loss, the primary user (PU) signals received at the CR or secondary user (SU) can be practically too weak for reliable detection. To tackle this issue, we consider in this letter a new intelligent reflecting surface (IRS)-aided spectrum sensing scheme for CR, by exploiting the large aperture and passive beamforming gains of IRS to boost the PU signal strength received at the SU to facilitate its spectru…
Considering intelligent reflecting surface (IRS), we study a multi-cluster multiple-input-single-output (MISO) non-orthogonal multiple access (NOMA) downlink communication network. In the network, an IRS assists the communication from the base station (BS) to all users by passive beamforming. Our goal is to minimize the total transmit power by jointly optimizing the transmit beamforming vectors at the BS and the reflection coefficient vector at the IRS. Because of the restrictions on the IRS reflection amplitudes and phase shifts, the formulated quadratically constrained quadratic problem is h…
This work examines the performance gain achieved by deploying an intelligent reflecting surface (IRS) in covert communications. To this end, we formulate the joint design of the transmit power and the IRS reflection coefficients by taking into account the communication covertness for the cases with global channel state information (CSI) and without a warden's instantaneous CSI. For the case of global CSI, we first prove that perfect covertness is achievable with the aid of the IRS even for a single-antenna transmitter, which is impossible without an IRS. Then, we develop a penalty successive c…
This paper investigates the passive beamforming and deployment design for an intelligent reflecting surface (IRS) aided full-duplex (FD) wireless system, where an FD access point (AP) communicates with an uplink (UL) user and a downlink (DL) user simultaneously over the same time-frequency dimension with the help of IRS. Under this setup, we consider three deployment cases: 1) two distributed IRSs placed near the UL user and DL user, respectively; 2) one centralized IRS placed near the DL user; 3) one centralized IRS placed near the UL user. In each case, we aim to minimize the weighted sum tr…
Intelligent reflecting surface (IRS) is a new promising technology that is able to reconfigure the wireless propagation channel via smart and passive signal reflection. In this paper, we investigate the capacity region of a two-user communication network with one access point (AP) aided by $M$ IRS elements for enhancing the user-AP channels, where the IRS incurs negligible delay, thus the user-AP channels via the IRS follow the classic discrete memoryless channel model. In particular, we consider two practical IRS deployment strategies that lead to different effective channels between the user…
Intelligent reflecting surface (IRS) has emerged as a key enabling technology to realize smart and reconfigurable radio environment for wireless communications, by digitally controlling the signal reflection via a large number of passive reflecting elements in real-time. Different from conventional wireless communication techniques that only adapt to but have no or limited control over dynamic wireless channels, IRS provides a new and cost-effective means to combat the wireless channel impairments in a proactive manner. However, despite its great potential, IRS faces new and unique challenges …
Intelligent reflecting surface (IRS) is a promising technology for achieving spectrum and energy efficient wireless networks cost-effectively. Most existing works on IRS have focused on exploiting IRS to enhance the performance of wireless communication or wireless information transmission (WIT), while its potential for boosting the efficiency of radio-frequency (RF) wireless energy transmission (WET) still remains largely open. Although IRS-aided WET shares similar characteristics with IRS-aided WIT, they differ fundamentally in terms of design objective, receiver architecture, and practical …
The intelligent reflecting surface (IRS) is an emerging technique to extend the wireless coverage. In this letter, the performance of hybrid automatic repeat request (hybrid-ARQ) for an IRS-assisted system is analyzed. More specifically, the outage performance of the IRS-aided system using hybrid-ARQ protocol with chase combining is studied. Asymptotic analysis also shows that the outage performance improves better than linearly by increasing number of reflectors of the IRS-aided system. The results also verify the potential of combining the ARQ scheme in the link layer of the IRS-aided system…
This paper considers an intelligent reflecting sur-face (IRS)-aided simultaneous wireless information and power transfer (SWIPT) network, where multiple users decode data and harvest energy from the transmitted signal of a transmit-ter. The proposed design framework exploits the cost-effective IRS to establish favorable communication environment to improve the fair energy efficient. In particular, we study the max-min energy efficiency (EE) of the system by jointly designing the transmit information and energy beamforming at the base station (BS), phase shifts at the IRS, as well as the power …
In this work, two problems associated with a downlink multi-user system are considered with the aid of intelligent reflecting surface (IRS): weighted sum-rate maximization and weighted minimal-rate maximization. For the first problem, a novel DOuble Manifold ALternating Optimization (DOMALO) algorithm is proposed by exploiting the matrix manifold theory and introducing the beamforming matrix and reflection vector using complex sphere manifold and complex oblique manifold, respectively, which incorporate the inherent geometrical structure and the required constraint. A smooth double manifold al…
