Narrow beams are key to wireless communications in millimeter wave frequency bands. Beam alignment (BA) allows the base station (BS) to adjust the direction and width of the beam used for communication. During BA, the BS transmits a number of scanning beams covering different angular regions. The goal is to minimize the expected width of the uncertainty region (UR) that includes the angle of departure of the user. Conventionally, in interactive BA, it is assumed that the feedback corresponding to each scanning packet is received prior to transmission of the next one. However, in practice, the feedback delay could be larger because of propagation or system constraints. This paper investigates BA strategies that operate under arbitrary fixed feedback delays. This problem is analyzed through a source coding prospective where the feedback sequences are viewed as source codewords. It is shown that these codewords form a codebook with a particular characteristic which is used to define a new class of codes called d-unimodal codes. By analyzing the properties of these codes, a lower bound on the minimum achievable expected beamwidth is provided. The results reveal potential performance improvements in terms of the BA duration it takes to achieve a fixed expected width of the UR over the state-of-the-art BA methods which do not consider the effect of delay.
Millimeter-wave will be a key technology in next-generation wireless networks thanks to abundant bandwidth availability. However, the use of large antenna arrays with beamforming demands precise beam-alignment between transmitter and receiver, and may entail huge overhead in mobile environments. This paper investigates the design of an optimal interactive beam-alignment and data communication protocol, with the goal of minimizing power consumption under a minimum rate constraint. The base-station selects beam-alignment or data communication and the beam parameters, based on feedback from the u…
Millimeter wave (mmWave) technologies have the potential to achieve very high data rates, but suffer from intermittent connectivity. In this paper, we provision an architecture to integrate sub-6 GHz and mmWave technologies, where we incorporate the sub-6 GHz interface as a fallback data transfer mechanism to combat blockage and intermittent connectivity of the mmWave communications. To this end, we investigate the problem of scheduling data packets across the mmWave and sub-6 GHz interfaces such that the average delay of system is minimized. This problem can be formulated as Markov Decision P…
Delay alignment modulation (DAM) is a novel wideband communication technique, which exploits the high spatial resolution and multi-path sparsity of millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems to mitigate inter-symbol interference (ISI), without relying on conventional techniques like channel equalization or multi-carrier transmission. In this paper, we extend the DAM technique to multi-user mmWave massive MIMO communication systems. We first provide asymptotic analysis by showing that when the number of base station (BS) antennas is much larger than the total…
Accurate channel parameter estimation is challenging for wideband millimeter-wave (mmWave) large-scale hybrid arrays, due to beam squint and much fewer radio frequency (RF) chains than antennas. This paper presents a novel joint delay and angle estimation approach for wideband mmWave fully-connected hybrid uniform cylindrical arrays. We first design a new hybrid beamformer to reduce the dimension of received signals on the horizontal plane by exploiting the convergence of the Bessel function, and to reduce the active beams in the vertical direction through preselection. The important recurrenc…
Millimeter-wave (mmW)/Terahertz (THz) wideband communication employing a large-scale antenna array is a promising technique of the sixth-generation (6G) wireless network for realizing massive machine-type communications (mMTC). To reduce the access latency and the signaling overhead, we design a grant-free random access scheme based on joint active device detection and channel estimation (JADCE) for mmW/THz wideband massive access. In particular, by exploiting the simultaneously sparse and low-rank structure of mmW/THz channels with spreads in the delay-angular domain, we propose two multi-ran…
This paper presents 28 GHz and 73 GHz millimeter- wave propagation measurements performed in a typical office environment using a 400 Megachip-per-second broadband sliding correlator channel sounder and highly directional steerable 15 dBi (30 degrees beamwidth) and 20 dBi (15 degrees beamwidth) horn antennas. Power delay profiles were acquired for 48 transmitter-receiver location combinations over distances ranging from 3.9 m to 45.9 m with maximum transmit powers of 24 dBm and 12.3 dBm at 28 GHz and 73 GHz, respectively. Directional and omnidirectional path loss models and RMS delay spread st…
This paper presents an omnidirectional spatial and temporal 3-dimensional statistical channel model for 28 GHz dense urban non-line of sight environments. The channel model is developed from 28 GHz ultrawideband propagation measurements obtained with a 400 megachips per second broadband sliding correlator channel sounder and highly directional, steerable horn antennas in New York City. A 3GPP-like statistical channel model that is easy to implement in software or hardware is developed from measured power delay profiles and a synthesized method for providing absolute propagation delays recovere…
We propose a hybrid architecture that integrates RF (i.e., sub-6 GHz) and millimeter wave (mmWave) technologies for 5G cellular systems. In particular, communications in the mmWave band faces significant challenges due to variable channels, intermittent connectivity, and high energy usage. On the other hand, speeds for electronic processing of data is of the same order as typical rates for mmWave interfaces which makes the use of complex algorithms for tracking channel variations and adjusting resources accordingly impractical. Our proposed architecture integrates the RF and mmWave interfaces …
Communication in Millimeter wave (mmWave) band relies on narrow beams due to directionality, high path loss, and shadowing. One can use beam alignment (BA) techniques to find and adjust the direction of these narrow beams. In this paper, BA at the base station (BS) is considered, where the BS sends a set of BA packets to scan different angular regions while the user listens to the channel and sends feedback to the BS for each received packet. It is assumed that the packets and feedback received at the user and BS, respectively, can be correctly decoded. Motivated by practical constraints such …
Initial access is the process which allows a mobile user to first connect to a cellular network. It consists of two main steps: cell search (CS) on the downlink and random access (RA) on the uplink. Millimeter wave (mmWave) cellular systems typically must rely on directional beamforming (BF) in order to create a viable connection. The beamforming direction must therefore be learned-as well as used-in the initial access process for mmWave cellular networks. This paper considers four simple but representative initial access protocols that use various combinations of directional beamforming and o…
We develop a broadband channel estimation algorithm for millimeter wave (mmWave) multiple input multiple output (MIMO) systems with few-bit analog-to-digital converters (ADCs). Our methodology exploits the joint sparsity of the mmWave MIMO channel in the angle and delay domains. We formulate the estimation problem as a noisy quantized compressed-sensing problem and solve it using efficient approximate message passing (AMP) algorithms. In particular, we model the angle-delay coefficients using a Bernoulli-Gaussian-mixture distribution with unknown parameters and use the expectation-maximization…
This paper proposes a closed-loop sparse channel estimation (CE) scheme for wideband millimeter-wave hybrid full-dimensional multiple-input multiple-output and time division duplexing based systems, which exploits the channel sparsity in both angle and delay domains. At the downlink CE stage, random transmit precoder is designed at base station (BS) for channel sounding, and receive combiners at user devices (UDs) are designed to visualize hybrid array as a low-dimensional digital array for facilitating the multi-dimensional unitary ESPRIT (MDU-ESPRIT) algorithm to estimate respective angle-of…
Millimeter-wave (mmWave) and Terahertz (THz) will be used in the sixth-generation (6G) wireless systems, especially for indoor scenarios. This paper presents an indoor three-dimensional (3-D) statistical channel model for mmWave and sub-THz frequencies, which is developed from extensive channel propagation measurements conducted in an office building at 28 GHz and 140 GHz in 2014 and 2019. Over 15,000 power delay profiles (PDPs) were recorded to study channel statistics such as the number of time clusters, cluster delays, and cluster powers. All the parameters required in the channel generatio…
In this paper, we establish a general framework on the reduced dimensional channel state information (CSI) estimation and pre-beamformer design for frequency-selective massive multiple-input multiple-output MIMO systems employing single-carrier (SC) modulation in time division duplex (TDD) mode by exploiting the joint angle-delay domain channel sparsity in millimeter (mm) wave frequencies. First, based on a generic subspace projection taking the joint angle-delay power profile and user-grouping into account, the reduced rank minimum mean square error (RR-MMSE) instantaneous CSI estimator is de…
This paper presents directional and omnidirectional RMS delay spread statistics obtained from 28 GHz and 73 GHz ultrawideband propagation measurements carried out in New York City using a 400 Megachips per second broadband sliding correlator channel sounder and highly directional steerable horn antennas. The 28 GHz measurements did not systematically seek the optimum antenna pointing angles and resulted in 33% outage for 39 T-R separation distances within 200 m. The 73 GHz measurements systematically found the best antenna pointing angles and resulted in 14.3% outage for 35 T-R separation dist…
Millimeter wave (mmWave) communications systems are promising candidate to support extremely high data rate services in future wireless networks. MmWave communications exhibit high penetration loss (blockage) and require directional transmissions to compensate for severe channel attenuations and for high noise powers. When blockage occurs, there are at least two simple prominent options: 1) switching to the conventional microwave frequencies (fallback option) and 2) using an alternative non-blocked path (relay option). However, currently it is not clear under which conditions and network param…
In this paper, we consider an edge cache-assisted millimeter wave cloud radio access network (C-RAN). Each remote radio head (RRH) in the C-RAN has a local cache, which can pre-fetch and store the files requested by the actuators. Multiple RRHs form a cluster to cooperatively serve the actuators, which acquire their required files either from the local caches or from the central processor via multicast fronthaul links. For such a scenario, we formulate a beamforming design problem to minimize the secure transmission delay under transmit power constraint of each RRH. Due to the difficulty of di…
In many resource allocation problems, a centralized controller needs to award some resource to a user selected from a collection of distributed users with the goal of maximizing the utility the user would receive from the resource. This can be modeled as the controller computing an extremum of the distributed users' utilities. The overhead rate necessary to enable the controller to reproduce the users' local state can be prohibitively high. An approach to reduce this overhead is interactive communication wherein rate savings are achieved by tolerating an increase in delay. In this paper, we co…
Ultra-reliability and low-latency are pivotal requirements of the new 6th generation of communication systems (xURLLC). Over the past years, to increase throughput, adaptive active antennas were introduced in advanced wireless communications, specifically in the domain of millimeter-wave (mmWave). Consequently, new lower-layer techniques were proposed to cope with practical challenges of high dimensional and electronically-steerable beams. The transition from omni-directional to highly directional antennas presents a new type of wireless systems that deliver high bandwidth, but that are suscep…
One of the most promising approaches to overcome the drastic channel variations of millimeter wave (mmW) communications is to deploy dual-mode base stations that integrate both mmW and microwave (\muW) frequencies. Reaping the benefits of a dual-mode operation requires scheduling mechanisms that can allocate resources efficiently and jointly at both frequency bands. In this paper, a novel resource allocation framework is proposed that exploits users' context, in terms of user application (UA) delay requirements, to maximize the quality-of-service (QoS) of a dual-mode base station. In particula…
In this paper, a novel proactive computing and mmWave communication for ultra-reliable and low latency wireless virtual reality (VR is proposed. By leveraging information about users' poses, proactive computing and caching are used to pre-compute and store users' HD video frames to minimize the computing latency. Furthermore, multi-connectivity is exploited to ensure reliable mmWave links to deliver users' requested HD frames. The performance of the proposed approach is validated on a VR network serving an interactive gaming arcade, where dynamic and real-time rendering of HD video frames is n…
Millimeter-wave (mmWave) and sub-Terahertz (THz) frequencies are expected to play a vital role in 6G wireless systems and beyond due to the vast available bandwidth of many tens of GHz. This paper presents an indoor 3-D spatial statistical channel model for mmWave and sub-THz frequencies based on extensive radio propagation measurements at 28 and 140 GHz conducted in an indoor office environment from 2014 to 2020. Omnidirectional and directional path loss models and channel statistics such as the number of time clusters, cluster delays, and cluster powers were derived from over 15,000 measured…
Statistical channel models are instrumental to design and evaluate wireless communication systems. In the millimeter wave bands, such models become acutely challenging; they must capture the delay, directions, and path gains, for each link and with high resolution. This paper presents a general modeling methodology based on training generative neural networks from data. The proposed generative model consists of a two-stage structure that first predicts the state of each link (line-of-sight, non-line-of-sight, or outage), and subsequently feeds this state into a conditional variational autoenco…
When there are a large number of antennas in massive MIMO systems, the transmitted wideband signal will be sensitive to the physical propagation delay of electromagnetic waves across the large array aperture, which is called the spatial-wideband effect. In this scenario, transceiver design is different from most of the existing works, which presume that the bandwidth of the transmitted signals is not that wide, ignore the spatial-wideband effect, and only address the frequency selectivity. In this paper, we investigate spatial- and frequency-wideband effects, called dual-wideband effects, in m…
This paper presents a stochastic geometry-based analysis of propagation statistics for 5G millimeter wave (mm-wave) cellular. In particular, the time-of-arrival (TOA) and angle-of-arrival (AOA) distributions of the first-arriving multipath component (MPC) are derived. These statistics find their utility in many applications such as cellular-based localization, channel modeling, and link establishment for mm-wave initial access (IA). Leveraging tools from stochastic geometry, a Boolean model is used to statistically characterize the random locations, orientations, and sizes of reflectors, e.g.,…
Millimeter wave (mmWave) communication by utilizing lens antenna arrays is a promising technique for realizing cost-effective 5G wireless systems with large MIMO (multiple-input multiple-output) but only limited radio frequency (RF) chains. This paper studies an uplink multi-user mmWave single-sided lens MIMO system, where only the base station (BS) is equipped with a full-dimensional (FD) lens antenna array with both elevation and azimuth angle resolution capabilities, and each mobile station (MS) employs the conventional uniform planar array (UPA) without the lens. By exploiting the angle-de…
Comparisons of outdoor Urban Microcell (UMi) large-scale path loss models, root mean square (RMS) delay spreads (DS), angular spreads (AS), and the number of spatial beams for extensive measurements performed at 28, 38, 73, and 142 GHz are presented in this letter. Measurement campaigns were conducted from 2011-2020 in downtown Austin, Texas, Manhattan (New York City), and Brooklyn, New York with communication ranges up to 930 m. Key similarities and differences in outdoor wireless channels are observed when comparing the channel statistics across a wide range of frequencies from millimeter-wa…
To realize cooperative computation and communication in a relay mobile edge computing system, we develop a hybrid relay forward protocol, where we seek to balance the execution delay and network energy consumption. The problem is formulated as a nondifferentible optimization problem which is nonconvex with highly coupled constraints. By exploiting the problem structure, we propose a lightweight algorithm based on inexact block coordinate descent method. Our results show that the proposed algorithm exhibits much faster convergence as compared with the popular concave-convex procedure based algo…
There has been an increasing interest in the millimeter wave (mmW) frequency regime in the design of next-generation wireless systems. The focus of this work is on understanding mmW channel properties that have an important bearing on the feasibility of mmW systems in practice and have a significant impact on physical (PHY) layer design. In this direction, simultaneous channel sounding measurements at 2.9, 29 and 61 GHz are performed at a number of transmit-receive location pairs in indoor office, shopping mall and outdoor environments. Based on these measurements, this paper first studies lar…
The millimeter wave (mmWave) bands have recently attracted considerable interest for next-generation cellular systems due to the massive available bandwidths at these frequencies. However, a key challenge in designing mmWave cellular systems is initial access -- the procedure by which a mobile establishes an initial link-layer connection to a base station cell. MmWave communication relies on highly directional transmissions and the initial access procedure must thus provide a mechanism by which initial transmission directions can be searched in a potentially large angular space. Design options…
In this paper, we consider the design of joint resource blocks (RBs) and power allocation for dual-mode base stations operating over millimeter wave (mmW) band and microwave ($μ$W) band. The resource allocation design aims to minimize the system energy consumption while taking into account the channel state information, maximum delay, load, and different types of user applications (UAs). To facilitate the design, we first propose a group-based algorithm to assign UAs to multiple groups. Within each group, low-power UAs, which often appear in short distance and experience less obstacles, are in…
This paper presents small-scale fading measurements for 28 GHz outdoor millimeter-wave ultrawideband channels using directional horn antennas at the transmitter and receiver. Power delay profiles were measured at half-wavelength spatial increments over a local area (33 wavelengths) on a linear track in two orthogonal receiver directions in a typical base-to-mobile scenario with fixed transmitter and receiver antenna beam pointing directions. The voltage path amplitudes are shown to follow a Rician distribution, with K-factor ranging from 9 - 15 dB and 5 - 8 dB in line of sight (LOS) and non-li…
We propose beam division multiple access (BDMA) with per-beam synchronization (PBS) in time and frequency for wideband massive multiple-input multiple-output (MIMO) transmission over millimeter-wave (mmW)/Terahertz (THz) bands. We first introduce a physically motivated beam domain channel model for massive MIMO and demonstrate that the envelopes of the beam domain channel elements tend to be independent of time and frequency when both the numbers of antennas at base station and user terminals (UTs) tend to infinity. Motivated by the derived beam domain channel properties, we then propose PBS f…
Cell search is the process for a user to detect its neighboring base stations (BSs) and make a cell selection decision. Due to the importance of beamforming gain in millimeter wave (mmWave) and massive MIMO cellular networks, the directional cell search delay performance is investigated. A cellular network with fixed BS and user locations is considered, so that strong temporal correlations exist for the SINR experienced at each BS and user. For Poisson cellular networks with Rayleigh fading channels, a closed-form expression for the spatially averaged mean cell search delay of all users is der…
Millimeter wave (mmWave) communication systems use large number of antenna elements that can potentially overcome severe channel attenuation by narrow beamforming. Narrow-beam operation in mmWave networks also reduces multiuser interference, introducing the concept of noise-limited wireless networks as opposed to interference-limited ones. The noise-limited or interference-limited regime heavily reflects on the medium access control (MAC) layer throughput and on proper resource allocation and interference management strategies. Yet, these regimes are ignored in current approaches to mmWave MAC…
Channel estimation at millimeter wave (mmWave) is challenging when large antenna arrays are used. Prior work has leveraged the sparse nature of mmWave channels via compressed sensing based algorithms for channel estimation. Most of these algorithms, though, assume perfect synchronization and are vulnerable to phase errors that arise due to carrier frequency offset (CFO) and phase noise. Recently sparsity-aware, non-coherent beamforming algorithms that are robust to phase errors were proposed for narrowband phased array systems with full resolution analog-to-digital converters (ADCs). Such ener…
Millimeter wave (mmWave) communication is envisioned as a cornerstone to fulfill the data rate requirements for fifth generation (5G) cellular networks. In mmWave communication, beamforming is considered as a key technology to combat the high path-loss, and unlike in conventional microwave communication, beamforming may be necessary even during initial access/cell search. Among the proposed beamforming schemes for initial cell search, analog beamforming is a power efficient approach but suffers from its inherent search delay during initial access. In this work, we argue that analog beamforming…
We study the problem of communication over an additive white Gaussian noise (AWGN) channel with an AWGN feedback channel. When the feedback channel is noiseless, the classic Schalkwijk-Kailath (S-K) scheme is known to achieve capacity in a simple sequential fashion, while attaining reliability superior to non-feedback schemes. In this work, we show how simplicity and reliability can be attained even when the feedback is noisy, provided that the feedback channel is sufficiently better than the feedforward channel. Specifically, we introduce a low-complexity low-delay interactive scheme that ope…
Millimeter wave (mmWave) communications which essentially employ directional antennas find applications spanning from indoor short range wireless personal area networks to outdoor cellular networks. A thorough understanding of mmWave signal propagation through the wireless channel provides valuable insights for the design of such networks which in turn dictates the achievable performance limits. High path loss, penetration loss, and negligible signal scattering are certain distinctive features of the mmWave channel which necessitates the development of new mathematical models. Importantly, the…
There have been active research activities worldwide in developing the next-generation 5G wireless network. The 5G network is expected to support significantly large amount of mobile data traffic and huge number of wireless connections, achieve better cost- and energy-efficiency as well as quality of service (QoS) in terms of communication delay, reliability and security. To this end, the 5G wireless network should exploit potential gains in different network dimensions including super dense and heterogeneous deployment of cells and massive antenna arrays (i.e., massive multiple input multiple…
Millimeter-wave (mm-wave) is a promising technique to enhance the network capacity and coverage of next-generation (5G) based on utilizing a great number of available spectrum resources in mobile communication. Improving the 5G network requires enhancing and employing mm-wave beamforming channel propagation characteristics. To achieve high data rates, system performance remains a challenge given the impact of propagation channels in mm-wave that is insufficient in both path loss, delay spread, and penetration loss. Additional challenges arise due to high cost and energy consumption, which requ…
In this paper, we investigate the problem of beam alignment in millimeter wave (mmWave) systems, and design an optimal algorithm to reduce the overhead. Specifically, due to directional communications, the transmitter and receiver beams need to be aligned, which incurs high delay overhead since without a priori knowledge of the transmitter/receiver location, the search space spans the entire angular domain. This is further exacerbated under dynamic conditions (e.g., moving vehicles) where the access to the base station (access point) is highly dynamic with intermittent on-off periods, requirin…
In millimeter wave (mmWave) communication systems, narrow beam operations overcome severe channel attenuations, reduce multiuser interference, and thus introduce the new concept of noise-limited mmWave wireless networks. The regime of the network, whether noise-limited or interference-limited, heavily reflects on the medium access control (MAC) layer throughput and on proper resource allocation and interference management strategies. Yet, alternating presence of these regimes and, more importantly, their dependence on the mmWave design parameters are ignored in the current approaches to mmWave…
The use of low-precision analog-to-digital converters (ADCs) is a low-cost and power-efficient solution for a millimeter wave (mmWave) multiple-input multiple-output (MIMO) system operating at sampling rates higher than a few Gsample/sec. This solution, however, can make significant frame-error-rates (FERs) degradation due to inter-subcarrier interference when applying conventional frequency-domain equalization techniques. In this paper, we propose computationally-efficient yet near-optimal soft-output detection methods for the coded mmWave MIMO systems with low-precision ADCs. The underlying …
We consider the problem of downlink channel estimation for millimeter wave (mmWave) MIMO-OFDM systems, where both the base station (BS) and the mobile station (MS) employ large antenna arrays for directional precoding/beamforming. Hybrid analog and digital beamforming structures are employed in order to offer a compromise between hardware complexity and system performance. Different from most existing studies that are concerned with narrowband channels, we consider estimation of wideband mmWave channels with frequency selectivity, which is more appropriate for mmWave MIMO-OFDM systems. By expl…
Reconfigurable Intelligent Surfaces (RIS) are considered a key enabler to achieve the vision of Smart Radio Environments, where the propagation environment can be programmed and controlled to enhance the efficiency of wireless systems. These surfaces correspond to planar sheets comprising a large number of small and low-cost reflecting elements whose parameters are adaptively selected with a programmable controller. Hence, by optimizing these coefficients, the information signals can be directed in a customized fashion. On the other hand, the initial access procedure used in 5G is beam sweepin…
In this paper, a novel dual-mode scheduling framework is proposed that jointly performs user applications (UA) selection and scheduling over microwave ($μ$W) and millimeter wave (mmW) bands. The proposed scheduling framework utilizes a set of context information, including the channel state information, the delay tolerance and required load per UA, and the uncertainty of mmW channels, to maximize the quality-of-service (QoS) per UA. The scheduling problem is formulated as an optimization with minimum unsatisfied relations (min-UR) problem which is shown to be challenging to solve. Consequently…
In this paper, we present a novel real-time multiple-input-multiple-output (MIMO) channel sounder for the 28 GHz band. Until now, most investigations of the directional characteristics of millimeter-wave channels have used mechanically rotating horn antennas. In contrast, the sounder presented here is capable of performing horizontal and vertical beam steering with the help of phased arrays. Due to its fast beam-switching capability, the proposed sounder can perform measurements that are directionally resolved both at the transmitter(TX) and receiver (RX) in 1.44 milliseconds compared to the m…
Millimeter wave (mmW) communications at the 60 GHz unlicensed band is seen as a promising approach for boosting the capacity of wireless local area networks (WLANs). If properly integrated into legacy IEEE 802.11 standards, mmW communications can offer substantial gains by offloading traffic from congested sub-6 GHz unlicensed bands to the 60 GHz mmW frequency band. In this paper, a novel medium access control (MAC) is proposed to dynamically manage the WLAN traffic over the unlicensed mmW and sub-6 GHz bands. The proposed protocol leverages the capability of advanced multi-band wireless stati…
Directional transmission patterns (a.k.a. narrow beams) are the key to wireless communications in millimeter wave (mmWave) frequency bands which suffer from high path loss and severe shadowing. In addition, the propagation channel in mmWave frequencies incorporates only a few number of spatial clusters requiring a procedure to align the corresponding narrow beams with the angle of departure (AoD) of the channel clusters. The objective of this procedure, called beam alignment (BA) is to increase the beamforming gain for subsequent data communication. Several prior studies consider optimizing BA…
Mobility and blockage are two critical challenges in wireless transmission over millimeter-wave (mmWave) and Terahertz (THz) bands. In this paper, we investigate network massive multiple-input multiple-output (MIMO) transmission for mmWave/THz downlink in the presence of mobility and blockage. Considering the mmWave/THz propagation characteristics, we first propose to apply per-beam synchronization for network massive MIMO to mitigate the channel Doppler and delay dispersion effects. Accordingly, we establish a transmission model. We then investigate network massive MIMO downlink transmission …
In this paper, a novel coordinated initial access (IA) scheme for clustered millimeter wave small cells (mmSCs) is proposed for the fifth generation mobile communication networks (5G). This solution is a method for efficient and fast initial access for ultra-dense millimeter wave standalone networks without presence of overlaid legacy networks operating on lower frequency. In contrast to the current full beam sweep scheme, where time consuming exhaustive searching is employed, the mmSCs within one cluster will perform the IA procedure in a coordinated manner based on the power delay profile (P…
Recently millimeter-wave bands have been postulated as a means to accommodate the foreseen extreme bandwidth demands in vehicular communications, which result from the dissemination of sensory data to nearby vehicles for enhanced environmental awareness and improved safety level. However, the literature is particularly scarce in regards to principled resource allocation schemes that deal with the challenging radio conditions posed by the high mobility of vehicular scenarios. In this work we propose a novel framework that blends together Matching Theory and Swarm Intelligence to dynamically and…
Communication in high frequencies such as millimeter wave and terahertz suffer from high path-loss and intense shadowing which necessitates beamforming for reliable data transmission. On the other hand, at high frequencies the channels are sparse and consist of few spatial clusters. Therefore, beam alignment (BA) strategies are used to find the direction of these channel clusters and adjust the width of the beam used for data transmission. In this work, a single-user uplink scenario where the channel has one dominant cluster is considered. It is assumed that the user transmits a set of BA pack…
Meta distribution is a fine-grained unified performance metric that enables us to evaluate the {reliability and latency} of next generation wireless networks, in addition to the conventional coverage probability. In this paper, using stochastic geometry tools, we develop a systematic framework to characterize the meta distributions of the downlink signal-to-interference-ratio (SIR)/signal-to-noise-ratio (SNR) and data rate of a typical device in a cellular network with coexisting sub-6GHz and millimeter wave (mm-wave) spectrums. Macro base-stations (MBSs) transmit on sub-6GHz channels (which w…
Chirp Delay-Doppler Domain Modulation Based Joint Communication and Radar for Autonomous Vehicles
Beijing Institute of Technology（北京理工大学）；Ocean University of China（中国海洋大学）；Nanyang Technological University（南洋理工大学）；Tsinghua University（清华大学）；Aristotle University of Thessaloniki（塞萨洛尼基亚里士多德大学）
Beijing Institute of Technology（北京理工大学）；Tsinghua University（清华大学）；Université Paris-Saclay（巴黎萨克雷大学）；CNRS（法国国家科学研究中心）；CentraleSupélec（中央理工-高等电力学院）
This paper proposes a model-driven deep learning (MDDL)-based channel estimation and feedback scheme for wideband millimeter-wave (mmWave) massive hybrid multiple-input multiple-output (MIMO) systems, where the angle-delay domain channels' sparsity is exploited for reducing the overhead. Firstly, we consider the uplink channel estimation for time-division duplexing systems. To reduce the uplink pilot overhead for estimating the high-dimensional channels from a limited number of radio frequency (RF) chains at the base station (BS), we propose to jointly train the phase shift network and the cha…
