The absorption of electromagnetic radiation by a planar structure, consisting of a three-layer dielectric-metal-dielectric coating on a metal back-reflector is analysed. The conditions for total absorption are derived. Our analysis shows that, in contrast with bi-layer structures, the calculated layer thicknesses are feasible to fabricate for any metal. The proposed absorber design is of potential use in infrared and longer wavelength detectors and for radiant energy harvesting devices.
We propose an efficient multiband absorber comprising a truncated one-dimensional periodic metal-dielectric photonic crystal and a reflective substrate. The reflective substrate is actually an optically thick metallic film. Such a planar device is easier to fabricate compared with the absorbers with complicated shapes. For a 4-unit cell device, all of the four absorption peaks can be optimized with efficiencies higher than 95%. Moreover, those absorption peaks are insensitive to both polarization and incident angle. The influences of the geometrical parameters along with the refractive index o…
A metamaterial perfect absorber consisting of a tri-layer (Al/ZnS/Al) metal-dielectric-metal system with top aluminium nano-disks is fabricated by laser-interference lithography and lift-off processing. The metamaterial absorber had peak resonant absorbance at 1090 nm and showed nonlinear absorption for 600ps laser pulses at 1064 nm wavelength. A nonlinear saturation of reflectance was measured to be dependent on the average laser power incident and not the peak laser intensity. The nonlinear behaviour is shown to arise from the heating due to the absorbed radiation and photo-thermal changes i…
An ideal solar thermal absorber has a sharp transition between high and low absorptance at the wavelength where the blackbody emissive power begins to exceed the solar irradiance. However, most real selective absorbers have a fairly broad transition, leading to both solar absorption and thermal emission losses. Here, we model, fabricate, and characterize a highly selective semiconductor-dielectric-metal (Ga0.46In0.54As - MgF2 - Ag) solar absorber with an extremely sharp transition from high to low absorptance. The thin semiconductor serves as a selective filter, absorbing photons with waveleng…
We numerically and experimentally investigate graphene-based optical absorbers that exploit guided mode resonances (GMRs) achieving perfect absorption over a bandwidth of few nanometers (over the visible and near-infrared ranges) with a 40-fold increase of the monolayer graphene absorption. We analyze the influence of the geometrical parameters on the absorption rate and the angular response for oblique incidence. Finally, we experimentally verify the theoretical predictions in a one-dimensional, dielectric grating and placing it near either a metallic or a dielectric mirror.
We derive periodic multilayer absorbers with effective uniaxial properties similar to perfectly matched layers (PML). This approximate representation of PML is based on the effective medium theory and we call it an effective medium PML (EM-PML). We compare the spatial reflection spectrum of the layered absorbers to that of a PML material and demonstrate that after neglecting gain and magnetic properties, the absorber remains functional. This opens a route to create electromagnetic absorbers for real and not only numerical applications and as an example we introduce a layered absorber for the w…
We investigate the capabilities of the effective non-retarded method (ENR) to explore and design nanoparticles composites with specific optical properties. We consider a composite material comprising periodically distributed metallic spheres in a dielectric host matrix. The effective macroscopic dielectric function of the composite medium is obtained by means of the ENR and is used to calculate the electromagnetic response of a slab made of such an inhomogeneous material. This response is compared with that obtained using the Korringa-Kohn-Rostoker wave calculation method (KKR). We analyze the…
While various nanophotonic structures applicable to relatively thin crystalline silicon-based solar cells were proposed to ensure effective light in-coupling and light trapping in the absorber, it is of great importance to evaluate their performance on the solar module level under realistic irradiation conditions. Here, we analyze the annual energy yield of relatively thin heterojunction (HJT) solar module architectures when optimized anti-reflective and light trapping titanium dioxide (TiO$_2$) nanodisk square arrays are applied on the front and rear cell interfaces. Our numerical study shows…
We experimentally demonstrate a wide band near perfect light absorber in the mid-wave infrared region using multiplexed plasmonic metal structures. The wide band near perfect light absorber is made of two different size gold metal squares multiplexed on a thin dielectric spacing layer on the top of a thick metal layer in each unit cell. We also fabricate regular non-multiplexed structure perfect light absorbers. The multiplexed structure IR absorber absorbs above 98% incident light over a much wider spectral band than the regular non-multiplexed structure perfect light absorbers in the mid-wav…
When the effects of dispersion are included, neither the Abraham nor the Minkowski expression for electromagnetic momentum in a dielectric medium gives the correct recoil momentum for absorbers or emitters of radiation. The total momentum density associated with a field in a dielectric medium has three contributions: (i) the Abraham momentum density of the field, (ii) the momentum density associated with the Abraham force, and (iii) a momentum density arising from the dispersive part of the response of the medium to the field, the latter having a form evidently first derived by D.F. Nelson [Ph…
We present a general principle for the rational design of dielectric optical antennas with optimal solar absorption enhancement: leaky mode engineering. This builds upon our previous study that demonstrates the solar absorption of a material with a given volume only dependent on the density and the radiative loss of leaky modes of the material. Here we systematically examine the correlation among the modal properties (density and radiative loss) of leaky modes, physical features, and solar absorption of dielectric antenna structures. Our analysis clearly points out the general guidelineS for t…
A nearly omni-directional THz absorber for both transverse electric (TE) and transverse magnetic (TM) polarizations is proposed. Through the excitation of magnetic polariton in a metal-dielectric layer, the incident light is perfectly absorbed in a thin thickness which is about 25 times smaller than the resonance wavelength. By simply stacking several such structural layers with different geometrical dimensions, the bandwidth of this strong absorption can be effectively enhanced due to the hybridization of magnetic polaritons in different layers.
In this paper, a plasmonic absorber consisting of a metal-dielectric-metal stack with a top layer of Sierpinski nanocarpet is theoretically investigated. Such compact absorber depicts broadband angle-independent behavior over a wide optical wavelength range ($400-700$ nm) and a broad range of angles of light incidence ($0-80^{\circ}$). Including several feature sizes, such fractal-like structure shows widely strong extinction ($85-99$%) response for either transverse electric or magnetic polarization states under normal incidence. Underlying mechanisms of absorbance due to excited surface plas…
Near perfect infrared light absorption at multi-spectral wavelengths has been experimentally demonstrated by using multiplexed metal square plasmon resonance structures. Optical power absorption over 95% has been observed in dual-band metamaterial absorbers at two separate wavelengths and optical power absorption over 92.5% has been observed in triple-band metamaterial absorbers at three separate wavelengths. The peak absorption wavelengths are primarily determined by the sizes of the metal squares in the multiplexed structures. Electrical field distributions in the middle of the dielectric sp…
Over the last decade, plasmonic antireflecting nanostructures have been extensively studied to be utilized in various optical and optoelectronic systems such as lenses, solar cells, photodetectors, and others. The growing interest to all-dielectric photonics as an alternative optical technology along with plasmonics motivates us to compare antireflection properties of all-dielectric and plasmonic nanoparticle coatings based on silver and crystalline silicon. Our results of numerical simulations for periodic arrays of spherical nanoparticles on top of amorphous silicon show that both silicon an…
This article presents a novel approach for designing dual-band absorbers based on graphene and metallic metasurfaces for terahertz and mid-infrared regimes, respectively. The absorbers are composed of a two-dimensional (2D) array of square patches deposited on a dielectric film terminated by a metal plate. Using an analytical circuit model, we obtain closed-form relations for different parameters of the structure to achieve the dual-band absorber. Two absorption bands with obtained absorptivity of 98% at 0.55 and 1.54 THz for the graphene-based structure and 7 and 25 THz for the metallic-based…
In this paper, we have proposed ultra-broadband terahertz absorber with three layers of periodic graphene disks arrays (PGDAs). A gold layer was utilized as backside reflector and TOPAS as dielectric spacers. Circuit model of PGDAs and the developed Transmission Line Model (TLM) for the absorber is utilized to design the structure using impedance matching concept. The validity of the results of the device was confirmed by Finite Element Method (FEM). The structure absorbs both TE and TM polarizations. Furthermore, the obtained normalized absorption bandwidth is 148% with a bandwidth of 2.64 TH…
In this paper the design for an absorbing metamaterial with near unity absorbance in terahertz region is presented. The absorber's unit cell structure consists of two metamaterial resonators that couple to electric and magnetic fields separately. The structure allows us to maximize absorption by varying dielectric material and thickness and, hence the effective electrical permittivity and magnetic permeability.
Due to their large electric conductivity, stand-alone metallic films are highly reflective at microwave frequencies. For this reason, it is nearly impossible to observe Faraday rotation in ferromagnetic metal layers, even in films just tens of nanometers thick. Here, we show using numerical simulations that a stack of cobalt nano-layers interlaced between dielectric layers can become highly transmissive and display a large Faraday rotation in a finite frequency band. A 45-degree Faraday rotation can be achieved with metallic ferromagnetic layers as thin as tens of nanometers.
An ultrabroad absorber based on double-ring-shaped titanium nitride (TiN) nanoresonators, which can work in high temperatures, is proposed and numerically studied. The absorber with some optimal parameters exhibits an averaged absorption of 94.6% in the range of 200 - 4000 nm (from ultraviolet to mid-infrared) and a band from 200 - 3518 nm having an absorption > 90%. We have demonstrated in detail the physical mechanisms of the ultra-broad absorption, including the dielectric lossy property of TiN material itself in shorter wavelengths and plasmonic resonances caused by the metallic property o…
We propose herein a method of material-structure integrated design for broadband absorption of dielectric metamaterial, which is achieved by combination of genetic algorithm and simulation platform. A multi-layered metamaterial absorber with an ultra-broadband absorption from 5.3 to 18 GHz (a relative bandwidth of as high as 109%) is realized numerically and experimentally. In addition, simulated results demonstrate the proposed metamaterial exhibits good incident angle and polarization tolerance, which also are significant criteria for practical applications. By investigating the working prin…
We demonstrated an ultra-broadband, polarization-insensitive and wide-angle metamaterial absorber for terahertz (THz) frequencies using arrays of truncated pyramid unit structure made of metal-dielectric multilayer composite. In our design each sub-layer behaving as an effective waveguide is gradually modified in their lateral width to realize a wideband response by effectively stitching together the resonance bands of different waveguide modes. Experimentally, our five layer sample with a total thickness 21um is capable of producing a large absorptivity above 80% from 0.7 to 2.3 THz up to the…
A one-dimensional dielectric grating, based on a simple geometry, is proposed and investigated to enhance light absorption in a monolayer graphene exploiting guided mode resonances. Numerical findings reveal that the optimized configuration is able to absorb up to 60% of the impinging light at normal incidence for both TE and TM polarizations resulting in a theoretical enhancement factor of about 26 with respect to the monolayer graphene absorption (about 2.3%). Experimental results confirm this behaviour showing CVD graphene absorbance peaks up to about 40% over narrow bands of few nanometers…
By a hybrid integration of plasmonic and dielectric waveguide concepts, it is shown that coherent perfect absorption can be achieved in a co-propagant coupler geometry. The device holds promises for classical and quantum signal processing. First, the operating principle of the proposed device is detailed in the context of a more general 2x2 lossy coupler formalism. Then, it is shown how to tune the device in a wide region of possible working points, its broadband operation, and the tolerance to fabrication uncertainties. Finally, a complete picture of the electromagnetic modes inside the hybri…
We suggest to exploit dielectric-metal core-shell nanostructures for efficient resonant and yet broadband absorption of infrared radiation with deeply subwavelength configurations. Realizing that nanostructures would efficiently absorb radiation only when their dielectric properties match those of the environment and making use of the effective medium approach, we develop the design strategy using core-shell nanostructures with very thin shells made of poor metals, i.e., metals having real and imaginary parts of their dielectric permittivities of the same order of magnitude. Analyzing in detai…
A metamaterial absorber converts solar radiation into heat for applications in thermoelectric generators and solar thermophotovoltaics. A metamaterial absorber typically consists of metallic parts separated by an insulator layer which does not allow the total heat extraction via direct heat conduction. Here, we propose wide-angle and broadband metamaterial absorber comprising an insulator layer, metal grating, and metal back plane (IMM) that allows the total heat extraction via direct heat conduction. We have formulated the quasi-analytical solution (QANS) of the IMM-absorber by applying the c…
We propose a design for an universal absorber, characterized by a resonance frequency that can be tuned from visible to microwave frequencies independently of the choice of the metal and the dielectrics involved. An almost resonant perfect absorption up to 99.8 % is demonstrated at resonance for all polarization states of light and for a very wide angular aperture. These properties originate from a magnetic Fabry-Perot mode that is confined in a dielectric spacer of $λ/100$ thickness by a metamaterial layer and a mirror. An extraordinary large funneling through nano-slits explains how light ca…
Future laser-interferometric gravitational wave detectors (GWDs) will potentially employ test mass mirrors from crystalline silicon and a laser wavelength of $1550\,\rm{nm}$, which corresponds to a photon energy below the silicon bandgap. Silicon might also be an attractive high-refractive index material for the dielectric mirror coatings. Films of amorphous silicon (a-Si), however, have been found to be significantly more absorptive at $1550\,\rm{nm}$ than crystalline silicon (c-Si). Here, we investigate the optical absorption of a Si/SiO$_2$ dielectric coating produced with the ion plating t…
The Brewster's law predicts zero reflection of p-polarization on a dielectric surface at a particular angle. However, when loss is introduced into the permittivity of the dielectric, the Brewster condition breaks down and reflection unavoidably appears. In this work, we found an exception to this long-standing dilemma by creating a class of nonmagnetic anisotropic metamaterials, where an anomalous Brewster effects with independently tunable absorption and refraction emerges. This loss-independent Brewster effect is bestowed by the extra degrees of freedoms introduced by anisotropy and strictly…
This paper presents fabrication, measurement and modelling results for a metal-dielectric-metal metasurface absorber for solar thermal applications. The structure uses amorphous carbon as an inter-layer between thin gold films with the upper film patterned with a 2D periodic array using focused ion beam etching. The patterned has been optimised to give high absorptance from 400-1200nm and low absorptance above this wavelength range to minimise thermal radiation and hence obtain higher temperature performance. Wide angle absorptance results are shown and detailed modelling of a realistic nanost…
Increasing attention on microwave ultra-broadband metamaterial absorbers has been paid due to their promising applications. While most microwave ultra-broadband metamaterial absorbers developed so far are based on metallic resonant structures, dispersive dielectric water-based metamaterial opens a simpler and more versatile route for the construction of polarization- and angle- insensitive ultra-broadband absorption. Here, we review the recent progresses of water-based metamaterial absorber by providing an illustration of the mechanisms to realize ultra-broadband, tunable and multi-functional …
The fabrication of functional metamaterials with extreme feature resolution finds a host of applications such as the broad area of surface/light interaction. Non-planar features of such structures can significantly enhance their performance and tunability, but their facile generation remains a challenge. Here, we show that carefully designed out-of-plane nanopillars made of metal-dielectric composites integrated in a metal-dielectric-nanocomposite configuration, can absorb broadband light very effectively. We further demonstrate that electrohydrodynamic printing in a rapid nanodripping mode, i…
A metamaterial composed of thin metallic strips as an efficient broadband absorber in the mid-infrared spectrum is investigated. Here the matching between dielectric and geometrical properties of the individual elements is critical to ensure high absorption. Detailed theoretical analysis based on the electric dipole approximation is performed to characterize the absorption and scattering properties of the individual elements of the unit cell and the results are used to design the metamaterial composed of such configurations. The absorption cross-section of a strip-shaped element can exceed its…
A microwave ultra-broadband polarization-independent metamaterial absorber is demonstrated. It is composed of a periodic array of metal-dielectric multilayered quadrangular frustum pyramids. These pyramids possess resonant absorption modes at multi-frequencies, of which the overlapping leads to the total absorption of the incident wave over an ultra-wide spectral band. The experimental absorption at normal incidence is above 90% in the frequency range of 7.8-14.7GHz, and the absorption is kept large when the incident angle is smaller than 60 degrees. The experimental results agree well with th…
The enhanced nonlinear optical response of a one-dimensional (1D) photonic crystal (PC) made from polymers and graphene composites is observed. The graphene PC was fabricated by spin-coating. It shows obvious bandgaps at two wavelengths in transmittance. Femtosecond Z-scan measurement at 515 nm and 1030 nm reveals a distinct enhancement in the effective nonlinear absorption coefficient Beff (and imaginary part of third-order dielectric susceptibility ImX(3)) for graphene nanoflakes embedded in the PC, when compared with the bulk graphene-polymer dispersion. The effect is studied in a wide rang…
A new dielectric Fabry-Perot cavity was designed for a resonant enhancing optical absorption by a thin absorber layer embedded into the cavity. In this cavity, the front mirror is a subwavelength grating with $\sim 100$% retroreflection. For a HgCdTe absorber in a matching cavity of the new type, the design is shown to meet the combined challenges of increasing the absorbing efficiency of the entire device up to $\sim 100$% and reducing its size and overall complexity, compared to a conventional resonant cavity enhanced HgCdTe absorber, while maintaining a fairly good tolerance against the gra…
Photonic bandgap design is one of the most basic ways to effectively control the interaction between light and matter. However, the traditional photonic bandgap is always dispersive (blueshift with the increase of the incident angle), which is disadvantageous to the construction of wide-angle optical devices. Hypercrystal, that the photonic crystal with layered hyperbolic metamaterials (HMMs), can strongly modify the bandgap properties based on the anomalous wavevector dispersion of the HMM. Here, based on phase variation compensation between HMM and isotropic dielectric layers, we propose for…
Plasmonics offer an exciting way to mediate the interaction between light and matter, allowing strong field enhancement and confinement, large absorption and scattering at resonance. However, simultaneous realization of ultra-narrow band perfect absorption and electromagnetic field enhancement is challenging due to the intrinsic high optical losses and radiative damping in metals. Here, we propose an all-metal plasmonic absorber with an absorption bandwidth less than 8nm and polarization insensitive absorptivity exceeding 99%. Unlike traditional Metal-Dielectric-Metal configurations, we demons…
Metasurfaces possess vast wave-manipulation capabilities, including reflection and refraction of a plane wave into non-standard directions. This requires meticulously-designed sub-wavelength meta-atoms in each period of the metasurface which guarantee unitary coupling to the desired Floquet-Bloch mode or, equivalently, suppression of the coupling to other modes. Herein, we propose an entirely different scheme to achieve such suppression, alleviating the need to devise and realize such dense scrupulously-engineered polarizable particles. Extending the concept of anti-reflective coatings to enab…
Plasmonic materials and metamaterials have been widely utilized to achieve spectral transmission, reflection and absorption filters based on localized or delocalized resonances arising from the interaction of photons with nanostructured materials. Realization of visible-frequency, high-performance, large-area, optical filters based on nanoplasmonic materials is rather challenging due to nanofabrication related problems (cost, fabrication imperfection, surface roughness) and optical losses of metals. Here, we propose and demonstrate large-area perfect absorbers and transmission filters that ove…
The trapped rainbow effect has been mostly found on tapered anisotropic metamaterials (MMs) made of low loss noble metals, such as gold, silver, etc. In this work, we demonstrate that an anisotropic MM waveguide made of high loss metal tungsten can also support the trapped rainbow effect similar to the noble metal based structure. We show theoretically that an array of tungsten/germanium anisotropic nano-cones placed on top of a reflective substrate can absorb light at the wavelength range from 0.3 micrometer to 9 micrometer with an average absorption efficiency approaching 98%. It is found th…
We present quasi-analytical solutions (QANS) of hybrid platform (HP) comprising metallic grating (MG) and stacked-dielectric layers for terahertz (THz) radiation. The QANS are validated by finite difference time domain simulation. It is found that the Wood anomalies induce the high-order spoof surface plasmon resonances in the HP. The QANS are applied to optimize new perfect absorber for THz sensing of large-area thin film with ultrahigh figure of merit reaching fifth order of magnitude for the film thickness 0.0001p (p: MG period). The first-order Wood's anomaly of the insulator layer and the…
Analog computing has emerged as a promising candidate for real-time and parallel continuous data processing. This paper presents a reciprocal way for realizing asymmetric optical transfer functions (OTFs) in the reflection side of the on-axis processing channels. It is rigorously demonstrated that the presence of Cross-polarization Exciting Normal Polarizabilities (CPENP) of a reciprocal metasurface circumvents the famous challenge of Green's function approach in implementation of on-axis reflective optical signal processing while providing dual computing channels under orthogonal polarization…
We propose an infrared power switch based on an asymmetric high-Q microcavity incorporating a metallic nanolayer in close proximity to a layer made of a phase-change material (PCM). The microcavity is designed so that when the PCM layer is in the low-temperature phase, the metallic nanolayer coincides with a nodal plane of the resonant electric field component, to allow a high resonant transmittance. As the light intensity exceeds a certain threshold, light-induced heating of the PCM layer triggers the phase transition accompanied by an abrupt change in its refractive index in the vicinity of …
Metamaterial-based absorbers have been extensively investigated in the terahertz (THz) range with ever increasing performances. In this paper, we propose an all-dielectric THz absorber based on doped silicon. The unit cell consists of a silicon cross resonator with an internal cross-shaped air cavity. Numerical results suggest that the proposed absorber can operate from THz to mid-infrared, having an average power absorption of >95% between 0.6 and 10 THz. Experimental results using THz time-domain spectroscopy show a good agreement with simulations. The underlying mechanisms for broadband abs…
Complete absorption of electromagnetic waves is paramount in today's applications, ranging from photovoltaics to cross-talk prevention into sensitive devices. In this context, we use a genetic algorithm (GA) strategy to optimize absorption properties of periodic arrays of truncated square-based pyramids made of alternating stacks of metal/dielectric layers. We target ultra-broadband quasi-perfect absorption of normally incident electromagnetic radiations in the visible and near-infrared ranges (wavelength comprised between 420 and 1600 nm). We compare the results one can obtain by considering …
In this paper, we analytically design a simple configuration of a broadband THz and polarization-insensitive absorber. The mentioned absorber consists of two layers of graphene disks, and the transmission line model is considered for the whole of the proposed absorber's structure to design it accurately. Therefore, the input admittance of the designed absorber is obtained by the transmission line model. Also, the real part of the input admittance is approximately tuned to be matched to the free space admittance. In contrast, the imaginary part of it is closely adjusted to zero around the centr…
Modern nanophotonic and meta-optical devices utilize a tremendous number of structural degrees of freedom to enhance light--matter interactions. A fundamental question is how large such enhancements can be. We develop an analytical framework to derive upper bounds to single-frequency electromagnetic response, across near- and far-field regimes, for any materials, naturally incorporating the tandem effects of material- and radiation-induced losses. Our framework relies on a power-conservation law for the polarization fields induced in any scatterer. It unifies previous theories on optical scatt…
In this paper, we analytically design a simple configuration of a broadband THz and polarization-insensitive absorber. The mentioned absorber consists of two layers of graphene disks, and the transmission line model is considered for the whole of the proposed absorber's structure to design it accurately. Therefore, the input admittance of the designed absorber is obtained by the transmission line model. Also, the real part of the input admittance is approximately tuned to be matched to the free space admittance. In contrast, the imaginary part of it is closely adjusted to zero around the centr…
Power dissipation in electromagnetic absorbers is a quadratic function of the incident fields. To characterize an absorber, one needs to deal with the coupling that may occur between different excitations. Energy Absorption Interferometry (EAI) is a technique that highlights the independent degrees of freedom through which a structure can absorb energy: the natural absorption modes of the structure. The coupling between these modes vanishes. In this paper, we use the EAI formalism to analyse different kinds of plasmonic periodic absorbers while rigorously accounting for the coupling: resonant …
We present a guide for the design and fabrication of a CMOS-compatible metamaterial microstructure as an absorber of visible light with exceptionally high absorption efficiency (~ 98%), for wavelengths 400nm-700nm. The structural parameters of the microstructure have been optimized by using Finite Element method (FEM) based COMSOL multyphysics software simulations. An optimized 2D unit cell of the structure consists of 4um by 160 nm TiN base on glass substrate covered with 70 nm thick silicon dioxide (SiO2). A periodic structure of titanium nitride (TiN) straps (each of 90 nm thick and 2-micro…
We present an asymmetric bifacial graphene metasurface to realize tunable and broadband coherent perfect absorption (CPA) at terahertz (THz) frequencies. The proposed design is composed of two dissimilar graphene square patch metasurfaces stacked over an ultrathin dielectric substrate. Nonlinear CPA performance without resorting to optical nonlinearities and amplification are demonstrated based on wave interference phenomena taking place along and inside this subwavelength structure. Broadband asymmetric reflection from opposite directions is obtained in the case of single wave illumination. T…
A few-micron thick structure that shows nearly 100% resonant polarized absorptance at a predefined midinfrared wavelength is designed and simulated. Like resonant-cavity enhanced photodetector structure, it contains a thin absorber enclosed in a dielectric cavity but surrogates the mirrors by two grating-on-layer structures. Fair manufacturing tolerance while maintaining high peak efficiency is proved. Electromagnetic fields amplitudes and Poynting vector over the cavity-absorber area are visualized and topology of electromagnetic power flow for two linear polarizations is discussed.
