The development of Hybrid CMOS Detectors (HCDs) for X-Ray telescope focal planes will place them in con- tention with CCDs on future satellite missions due to their faster frame rates, flexible readout scenarios, lower power consumption, and inherent radiation hardness. CCDs have been used with great success on the current generation of X-Ray telescopes (e.g. Chandra, XMM, Suzaku, and Swift). However their bucket-brigade read-out architecture, which transfers charge across the chip with discrete component readout electronics, results in clockrate limited readout speeds that cause pileup (saturation) of bright sources and an inherent susceptibility to radiation induced displacement damage that limits mission lifetime. In contrast, HCDs read pixels with low power, on-chip multiplexer electronics in a random access fashion. Faster frame rates achieved with multi-output readout design will allow the next generation's larger effective area telescopes to observe bright sources free of pileup. Radiation damaged lattice sites effect a single pixel instead of an entire row. Random access, multi-output readout will allow for novel readout modes such as simultaneous bright-source-fast/whole-chip-slow readout. In order for HCDs to be useful as X-Ray detectors, they must show noise and energy resolution performance similar to CCDs while retaining advantages inherent to HCDs. We will report on readnoise, conversion gain, and energy resolution measurements of an X-Ray enhanced Teledyne HAWAII-1RG (H1RG) HCD and describe techniques of H1RG data reduction.
We present the results of x-ray measurements on a hybrid CMOS detector that uses a H2RG ROIC and a unique bonding structure. The silicon absorber array has a 36μm pixel size, and the readout array has a pitch of 18μm; but only one readout circuit line is bonded to each 36x36μm absorber pixel. This unique bonding structure gives the readout an effective pitch of 36μm. We find the increased pitch between readout bonds significantly reduces the interpixel capacitance of the CMOS detector reported by Bongiorno et al. 2010 and Kenter et al. 2005.
Future space-based X-ray telescope missions are likely to have significantly increased demands on detector read out rates due to increased collection area, and there will be a desire to minimize radiation damage in the interests of maintaining spectral resolution. While CCDs have met the requirements of past missions, active pixel sensors are likely to be a standard choice for some future missions due to their inherent radiation hardness and fast, flexible read-out architecture. One form of active pixel sensor is the hybrid CMOS sensor. In a joint program of Penn State University and Teledyne …
When an X-ray is incident onto the silicon absorber array of a detector, it liberates a large number of electrons, which tend to diffuse outward into what is referred to as the charge cloud. This number can vary from tens to thousands across the soft X-ray bandpass (0.1 - 10 keV). The charge cloud can then be picked up by several pixels, and forms a specific pattern based on the exact incident location of the X-ray. We present experimental results on subpixel resolution for a custom H2RG with 36 micron pixels, presented in Bray 2018, and compare the data to simulated images . We then apply the…
X-ray hybrid CMOS detectors (HCDs) are a promising candidate for future x-ray missions requiring high throughput and fine angular resolution along with large field-of-view, such as the high-definition x-ray imager (HDXI) instrument on the Lynx x-ray surveyor mission concept. These devices offer fast readout capability, low power consumption, and radiation hardness while maintaining high detection efficiency from 0.2 to 10 keV. In addition, x-ray hybrid CMOS sensors may be fabricated with small pixel sizes to accommodate high-resolution optics and have shown great improvements in recent years i…
Electron tracking based Compton imaging is a key technique to improve the sensitivity of Compton cameras by measuring the initial direction of recoiled electrons. To realize this technique in semiconductor Compton cameras, we propose a new detector concept, Si-CMOS hybrid detector. It is a Si detector bump-bonded to a CMOS readout integrated circuit to obtain electron trajectory images. To acquire the energy and the event timing, signals from N-side are also read out in this concept. By using an ASIC for the N-side readout, the timing resolution of few us is achieved. In this paper, we present…
The Speedster-EXD is a new 64x64 pixel, 40 $μ$m pixel pitch, 100 $μ$m depletion depth hybrid CMOS X-ray detector (HCD) with the capability of reading out only those pixels containing event charge, thus enabling fast effective frame rates. A global charge threshold can be specified, and pixels containing charge above this threshold are flagged and read out. The Speedster detector has also been designed with other advanced in-pixel features to improve performance, including a low-noise, high-gain CTIA amplifier that eliminates interpixel capacitance crosstalk (IPC), and in-pixel Correlated Doubl…
Next-generation X-ray observatories, such as the Lynx X-ray Observatory Mission Concept or other similar concepts in the coming decade, will require detectors with high quantum efficiency (QE) across the soft X-ray band to observe the faint objects that drive their mission science objectives. Hybrid CMOS Detectors (HCDs), a form of active-pixel sensor, are promising candidates for use on these missions because of their fast read-out, low power consumption, and intrinsic radiation hardness. In this work, we present QE measurements of a Teledyne H2RG HCD, performed using a gas-flow proportional …
We report on the initial results of an experiment to determine the effects of proton radiation damage on an X-ray hybrid CMOS detector (HCD). The device was irradiated at the Edwards Accelerator Lab at Ohio University with 8 MeV protons, up to a total absorbed dose of 3 krad(Si) (4.5 $\times$ 10$^9$ protons/cm$^2$). The effects of this radiation on read noise, dark current, gain, and energy resolution are then analyzed. This exposure is the first of several which will be used for characterizing detector performance at absorbed dose levels that are relevant for imaging devices operating in a de…
Intrapixel nonuniformity is known to exist in CCD and CMOS image sensors, though the effects in backside illuminated (BSI) CCDs are too small to be a concern for most astronomical observations. However, projects like the Large Synoptic Survey Telescope require precise knowledge of the detector characteristics, and intrapixel effects may need more attention. By scanning CCD and CMOS cameras with a small light spot (unresolved by the optics), we find in the images that the spot's flux, centroid displacement, and ellipticity vary periodically on the pixel scale in most cases. The amplitude of var…
Unlike optical CCDs, near-infrared detectors, which are based on CMOS hybrid readout technology, typically suffer from electrical crosstalk between the pixels. The interpixel capacitance (IPC) responsible for the crosstalk affects the point-spread function (PSF) of the telescope, increasing the size and modifying the shape of all objects in the images while correlating the Poisson noise. Upcoming weak lensing surveys that use these detectors, such as WFIRST, place stringent requirements on the PSF size and shape (and the level at which these are known), which in turn must be translated into re…
Due to the increasing dimension, complexity and cost of the future astronomical surveys, new technologies enabling more compact and simpler systems are required. The development of curved detectors allows to enhance the performances of the optical system used (telescope or astronomical instrument), while keeping the system more compact. We describe here a set of five curved CMOS detectors developed within a collaboration between CEA-LETI and CNRS-LAM. These fully-functional detectors 20 Mpix (CMOSIS CMV20000) have been curved to different radii of curvature and spherical shapes (both convex an…
In recent years, CCD-in-CMOS TDI image sensors are becoming increasingly popular for many small satellite missions to assure a fast and affordable access to space for Low Earth Observation. Our monolithic CCD-in-CMOS TDI imager features a specifically developed technology which combines the benefits of a classical CCD TDI with the advantages of CMOS System-On-a-Chip (SoC) design. Like CCD, this detector is also controlled by a large number of clock voltages. Optimizing these voltages allows to increase the performance of the detector by improving multiple characteristic parameters, such as ful…
Next-generation X-ray observatories, such as the Lynx X-ray Observatory Mission Concept, will require detectors with high quantum efficiency (QE) across the soft X-ray band to observe the faint objects that drive their mission science cases. Hybrid CMOS Detectors (HCDs), a form of active-pixel sensor, are promising candidates for use on these missions because of their faster read-out, lower power consumption, and greater radiation hardness than detectors used in the current generation of X-ray telescopes. In this work, we present QE measurements of a Teledyne H2RG HCD. These measurements were …
X-ray polarimetry in astronomy has not been exploited well, despite its importance. The recent innovation of instruments is changing this situation. We focus on a complementary MOS (CMOS) pixel detector with small pixel size and employ it as an x-ray photoelectron tracking polarimeter. The CMOS detector we employ is developed by GPixel Inc., and has a pixel size of 2.5 $\mathrmμ$m $\times$ 2.5 $\mathrmμ$m. Although it is designed for visible light, we succeed in detecting x-ray photons with an energy resolution of 176 eV (FWHM) at 5.9 keV at room temperature and the atmospheric condition. We m…
The Penn State X-ray detector lab, in collaboration with Teledyne Imaging Sensors (TIS), have progressed their efforts to improve soft X-ray Hybrid CMOS detector (HCD) technology on multiple fronts. Having newly acquired a Teledyne cryogenic SIDECAR ASIC for use with HxRG devices, measurements were performed with an H2RG HCD and the cooled SIDECAR. We report new energy resolution and read noise measurements, which show a significant improvement over room temperature SIDECAR operation. Further, in order to meet the demands of future high-throughput and high spatial resolution X-ray observatorie…
Development of a cosmic ray detector using CMOS sensors embedded in smartphones and Raspberry Pi devices
Research Institute for Engineering, Kanagawa University（神奈川大学工学研究科）；Faculty of Engineering, Kanagawa University（神奈川大学工学部）；College of Industrial Technology, Nihon University（日本大学生产工学部）
We present preliminary characterization of the Speedster-EXD, a new event driven hybrid CMOS detector (HCD) developed in collaboration with Penn State University and Teledyne Imaging Systems. HCDs have advantages over CCDs including lower susceptibility to radiation damage, lower power consumption, and faster read-out time to avoid pile-up. They are deeply depleted and able to detect x-rays down to approximately 0.1 keV. The Speedster-EXD has additional in-pixel features compared to previously published HCDs including: (1) an in-pixel comparator that enables read out of only the pixels with si…
X-ray Hybrid CMOS Detectors (HCDs) have advantages over X-ray CCDs due to their higher readout rate abilities, flexible readout, inherent radiation hardness, and low power, which make them more suitable for the next generation large area X-ray telescope missions. The Penn State high energy astronomy laboratory has been working on the development and characterization of HCDs in collaboration with Teledyne Imaging Sensors (TIS). We characterized an H2RG detector with a Cryo-SIDECAR readout and controller, and we find an improved energy resolution of ~2.7 % at 5.9 keV and read noise of ~6.5 e-. T…
We report on the characterization of four Teledyne Imaging Systems HAWAII Hybrid Si CMOS detectors designed for X-ray detection. Three H1RG detectors were studied along with a specially configured H2RG. Read noise measurements were performed, with the lowest result being 7.1 e- RMS. Interpixel capacitive crosstalk (IPC) was measured for the three H1RGs and for the H2RG. The H1RGs had IPC upper limits of 4.0 - 5.5 % (up & down pixels) and 8.7 - 9.7 % (left & right pixels), indicating a clear asymmetry. Energy resolution is reported for two X-ray lines, 1.5 & 5.9 keV, at multiple temperatures be…
While the successful launch and operation in space of the Gas Pixel Detectors onboard the PolarLight cubesat and the Imaging X-ray Polarimetry Explorer demonstrate the viability and the technical soundness of this class of detectors for astronomical X-ray polarimetry, it is clear that the current state of the art is not ready to meet the challenges of the next generation of experiments, such as the enhanced X-ray Timing and Polarimetry mission, designed to allow for a significantly larger data throughput. In this paper we describe the design and test of a new custom, self-triggering readout AS…
IDeF-X HD is a 32-channel analog front-end with self-triggering capability optimized for the readout of 16 x 16 pixels CdTe or CdZnTe pixelated detectors to build low power micro gamma camera. IDeF-X HD has been designed in the standard AMS CMOS 0.35 microns process technology. Its power consumption is 800 micro watt per channel. The dynamic range of the ASIC can be extended to 1.1 MeV thanks to the in-channel adjustable gain stage. When no detector is connected to the chip and without input current, a 33 electrons rms ENC level is achieved after shaping with 10.7 micro seconds peak time. Spec…
On-sky performance and prospects of near-infrared CMOS detectors in exoplanet detection: first year of SPIRIT
Cavendish Laboratory（卡文迪许实验室）；ETH Zurich（苏黎世联邦理工学院）；Instituto de Astrofísica de Canarias (IAC)（加那利群岛天体物理研究所）；Astrobiology Research Unit, Université de Liège（列日大学天体生物学研究单元）；Department of Earth, Atmospheric and Planetary Science, Massachusetts Institute of Technology（麻省理工学院地球、大气与行星科学系）；School of Physics & Astronomy, University of Birmingham（伯明翰大学物理与天文学院）
We have built and tested a compact, low-cost, but very-high-performance astronomical polarimeter based on a continuously rotating half-wave plate and a high-speed imaging detector. The polarimeter is suitable for small telescopes up to ~1 m in aperture. The optical system provides very high transmission over a wide wavelength range from the atmospheric UV cutoff to ~1000 nm. The high-quantum-efficiency, low-noise and high-speed of the detectors enable bright stars to be observed with high-precision as well as polarization imaging of extended sources. We have measured the performance of the ins…
In recent years, the performance of Scientifc Complementary Metal Oxide Semiconductor (sCMOS) sensors has been improved signifcantly. Compared with CCD sensors, sCMOS sensors have various advantages, making them potentially better devices for optical and X-ray detection, especially in time-domain astronomy. After a series of tests of sCMOS sensors, we proposed a new dedicated high-speed, large-format X-ray detector in 2016 cooperating with Gpixel Inc. This new sCMOS sensor has a physical size of 6 cm by 6 cm, with an array of 4096 by 4096 pixels and a pixel size of 15 um. The frame rate is 20.…
Scientific Complementary Metal Oxide Semiconductor (sCMOS) sensors are finding increasingly more applications in astronomical observations, thanks to their advantages over charge-coupled devices (CCDs) such as a higher readout frame rate, higher radiation tolerance, and higher working temperature. In this work, we investigate the performance at the individual pixel level of a large-format sCMOS sensor, GSENSE1516BSI, which has 4096 * 4096 pixels, each of 15 μm in size. To achieve this, three areas on the sCMOS sensor, each consisting of 99 * 99 pixels, are chosen for the experiment. The readou…
