Carbon nanotube field-effect transistors (CNT FETs) have been proposed as possible building blocks for future nano-electronics. But a challenge with CNT FETs is that they appear to randomly display varying amounts of hysteresis in their transfer characteristics. The hysteresis is often attributed to charge trapping in the dielectric layer between the nanotube and the gate. This study includes 94 CNT FET samples, providing an unprecedented basis for statistics on the hysteresis seen in five different CNT-gate configurations. We find that the memory effect can be controlled by carefully designing the gate dielectric in nm-thin layers. By using atomic layer depositions (ALD) of HfO$_{2}$ and TiO$_{2}$ in a triple-layer configuration, we achieve the first CNT FETs with consistent and narrowly distributed memory effects in their transfer characteristics.
Semiconducting single-walled carbon nanotubes are studied in the diffusive transport regime. The peak mobility is found to scale with the square of the nanotube diameter and inversely with temperature. The maximum conductance, corrected for the contacts, is linear in the diameter and inverse temperature. These results are in good agreement with theoretical predictions for acoustic phonon scattering in combination with the unusual band structure of nanotubes. These measurements set the upper bound for the performance of nanotube transistors operating in the diffusive regime.
Low-dimensional metallic transport is at the heart of modern high-performance transistors. While the best devices are currently based on III-V heterojunction quantum-well channels, we demonstrate that much greater performance gains reside in the unique properties of one-dimensional carbon nanotubes. Using recent experimental data, we show how the specific features of degenerate carrier kinetics in metallic nanotubes enable a novel class of quantum-confined signal detector whose current gain exceeds present transistor technology. We analyze the key interplay of degeneracy and scattering dynamic…
We use infrared thermometry of carbon nanotube network (CNN) transistors and find the formation of distinct hot spots during operation. However, the average CNN temperature at breakdown is significantly lower than expected from the breakdown of individual nanotubes, suggesting extremely high regions of power dissipation at the nanotube junctions. Statistical analysis and comparison with a thermal model allow the extraction of the average tube-tube junction thermal resistance, ~4.4x10^11 K/W (thermal conductance ~2.27 pW/K). This indicates that nanotube junctions have a much greater impact on C…
We present an approach for time-dependent quantum transport based on a self-consistent non-equilibrium Green function formalism. The technique is applied to a ballistic carbon nanotube transistor in the presence of a time harmonic signal at the gate. In the ON state the dynamic conductance exhibits plasmonic resonant peaks at terahertz frequencies. These vanish in the OFF state, and the dynamic conductance displays smooth oscillations, a signature of single particle quantum effects. We show that the nanotube kinetic inductance plays an essential role in the high-frequency behavior.
We have fabricated carbon nanotube (CN) field-effect transistors with multiple, individually addressable gate segments. The devices exhibit markedly different transistor characteristics when switched using gate segments controlling the device interior versus those near the source and drain. We ascribe this difference to a change from Schottky barrier modulation at the contacts to bulk switching. We also find that the current through the bulk portion is independent of gate length for any gate voltage, offering direct evidence for ballistic transport in semiconducting CNs over at least a few hun…
We describe a method to fabricate clean suspended single-wall carbon nanotube (SWCNT) transistors hosting a single quantum dot ranging in length from a few 10s of nm down to $\approx$ 3 nm. We first align narrow gold bow-tie junctions on top of individual SWCNTs and suspend the devices. We then use a feedback-controlled electromigration to break the gold junctions and expose nm-sized sections of SWCNTs. We measure electron transport in these devices at low temperature and show that they form clean and tunable single-electron transistors. These ultra-short suspended transistors offer the prospe…
We present a simple and scalable technique for the fabrication of solution processed & local gated carbon nanotube field effect transistors (CNT-FETs). The approach is based on directed assembly of individual single wall carbon nanotube from dichloroethane via AC dielectrophoresis (DEP) onto pre-patterned source and drain electrodes with a local aluminum gate in the middle. Local-gated CNT-FET devices display superior performance compared to global back gate with on-off ratios 10^4 and maximum subthreshold swings of 170 mV/dec. The local bottom-gated DEP assembled CNT-FETs will facilitate larg…
We report the radio-frequency performance of carbon nanotube array transistors that have been realized through the aligned assembly of highly separated, semiconducting carbon nanotubes on a fully scalable device platform. At a gate length of 100 nm, we observe output current saturation and obtain as-measured, extrinsic current gain and power gain cut-off frequencies, respectively, of 7 GHz and 15 GHz. While the extrinsic current gain is comparable to the state-of-the-art the extrinsic power gain is improved. The de-embedded, intrinsic current gain and power gain cut-off frequencies of 153 GHz …
We show that the performance of pentacene transistors can be significantly improved by maximizing the interfacial area at single walled carbon nanotube (SWCNT)/pentacene. The interfacial areas are varied by anchoring short SWCNTs of different densities (0-30/μm) to the Pd electrodes. The average mobility is increased three, six and nine times for low, medium and high SWCNT densities, respectively, compared to the devices with zero SWCNT. The current on-off ratio and on-current are increased up to 40 times and 20 times with increasing the SWCNT density. We explain the improved device performanc…
The observed performances of carbon nanotube field effect transistors are examined using first-principles quantum transport calculations. We focus on the nature and role of the electrical contact of Au and Pd electrodes to open-ended semiconducting nanotubes, allowing the chemical contact at the surface to fully develop through large-scale relaxation of the contacting atomic configuration. We present the first direct numerical evidence of Pd contacts exhibiting perfect transparency for hole injection as opposed to that of Au contacts. Their respective Schottky barrier heights, on the other han…
In this study, a model of a Schottky-barrier carbon nanotube field- effect transistor (CNT-FET), with ferromagnetic contacts, has been developed. The emphasis is put on analysis of current-voltage characteristics as well as shot (and thermal) noise. The method is based on the tight-binding model and the non- equilibrium Green's function technique. The calculations show that, at room temperature, the shot noise of the CNT FET is Poissonian in the sub-threshold region, whereas in elevated gate and drain/source voltage regions the Fano factor gets strongly reduced. Moreover, transport properties …
In the past decade, semiconducting carbon nanotube thin films have been recognized as contending materials for wide-ranging applications in electronics, energy, and sensing. In particular, improvements in large-area flexible electronics have been achieved through independent advances in post-growth processing to resolve metallic versus semiconducting carbon nanotube heterogeneity, in improved gate dielectrics, and in self-assembly processes. Moreover, controlled tuning of specific device components has afforded fundamental probes of the trade-offs between materials properties and device perfor…
We report dual-gate modulation of topological insulator field-effect transistors (TI FETs) made on Bi2Te3 thin flakes with integration of atomic-layer-deposited (ALD) Al2O3 high-k dielectric. Atomic force microscopy study shows that ALD Al2O3 is uniformly grown on this layer-structured channel material. Electrical characterization reveals that the right selection of ALD precursors and the related surface chemistry play a critical role in device performance of Bi2Te3 based TI FETs. We realize both top-gate and bottom-gate control on these devices, and the highest modulation rate of 76.1% is ach…
Atomistic density functional theory (DFT) calculations of the capacitance between a metallic cylindric gate and a carbon nanotube (CNT) are reported. Results stressing the predominant effect of quantum capacitance in limiting or even enhancing screening properties of the CNT are shown. Other contributions to the quantum capacitance beyond the electronic density of state (DOS) are pointed out. Negative values of the quantum capacitance are obtained for low-density systems, which correspondingly over-screen the gate field. This unconventional behavior of the quantum capacitance is related to the…
While decreasing the oxide thickness in carbon nanotube field-effect transistors (CNFETs) improves the turn-on behavior, we demonstrate that this also requires scaling the range of the drain voltage. This scaling is needed to avoid an exponential increase in Off-current with drain voltage, due to modulation of the Schottky barriers at both the source and drain contact. We illustrate this with results for bottom-gated ambipolar CNFETs with oxides of 2 and 5 nm, and give an explicit scaling rule for the drain voltage. Above the drain voltage limit, the Off-current becomes large and has equal ele…
We report on the electric measurements of an individual Au nanoparticle with an ultra-high contact resistance of about $10^{19} Ω$. The high-impedance measurements have been carried out by counting the electrons that are transferred onto the particle. In order to do this, a carbon nanotube is used as the electrode for the supply of electrons but also as the detector of the charge transfer. Measurements using single-electron detection allow us to determine the separation between the electron states in the Au nanoparticle, which is about 4 meV, consistent with the charging energy of the particle…
We have fabricated air-stable n-type, ambipolar carbon nanotube field effect transistors (CNFETs), and used them in nanoscale memory cells. N-type transistors are achieved by annealing of nanotubes in hydrogen gas and contacting them by cobalt electrodes. Scanning gate microscopy reveals that the bulk response of these devices is similar to gold-contacted p-CNFETs, confirming that Schottky barrier formation at the contact interface determines accessibility of electron and hole transport regimes. The transfer characteristics and Coulomb Blockade (CB) spectroscopy in ambipolar devices show stron…
Single electron transistors (SETs) made from single wall carbon nanotubes (SWCNTs) are promising for quantum electronic devices operating with ultra-low power consumption and allow fundamental studies of electron transport. We report on SETs made by registered in-plane growth utilizing tailored nanoscale catalyst patterns and chemical vapor deposition. Metallic SWCNTs have been removed by an electrical burn-in technique and the common gate hysteresis was removed using PMMA and baking, leading to field effect transistors with large on/off ratios up to 10^5. Further segmentation into 200 nm shor…
We use numerical simulations to analyze recent experimental measurements of short-channel carbon nanotube field-effect transistors with palladium contacts. We show that the gate strongly modulates the contact properties, an effect that is distinct from that observed in Schottky barrier carbon nanotube transistors. This modulation of the contacts by the gate allows for the realization of superior subthreshold swings for short channels, and improved scaling behavior. These results further elucidate the behavior of carbon nanotube-metal contacts, and should be useful in the optimization of high-p…
We measure the small signal, 1 GHz source-drain dynamical conductance of a back-gated single-walled carbon nanotube field effect transistor at both low and high dc bias voltages. At all bias voltages, the intrinsic device dynamical conductance at 1 GHz is identical to the low frequency dynamical conductance, consistent with the prediction of a cutoff frequency much higher than 1 GHz. This work represents a significant step towards a full characterization of a nanotube transistor for RF and microwave amplifiers.
The high-frequency transconductance and current noise of top-gated single carbon nanotube transistors have been measured and used to investigate hot electron effects in one-dimensional transistors. Results are in good agreement with a theory of 1-dimensional nano-transistor. In particular the prediction of a large transconductance correction to the Johnson-Nyquist thermal noise formula is confirmed experimentally. Experiment shows that nanotube transistors can be used as fast charge detectors for quantum coherent electronics with a resolution of $13\mathrm{μe/\sqrt{Hz}}$ in the 0.2-$0.8 \mathr…
We use scanning photocurrent microscopy (SPCM) to investigate the properties of internal p-n junctions as well as local defects in ambipolar carbon nanotube (CNT) transistors. Our SPCM images show strong signals near metal contacts whose polarity and positions change depending on the gate bias. SPCM images analyzed in conjunction with the overall conductance also indicate the existence and gate-dependent evolution of internal p-n junctions near contacts in the n-type operation regime. To determine the p-n junction position and the depletion width with a nanometer scale resolution, a Gaussian f…
We use numerical simulations to investigate the effect of electrostatics on the source and drain contacts of carbon nanotube field-effect transistors. We find that unscreened charge on the nanotube at the contact-channel interface leads to a potential barrier that can significantly hamper transport through the device. This effect is largest for intermediate gate voltages and for contacts near the ohmic-Schottky crossover, but can be mitigated with a reduction in the gate oxide thickness. These results help to elucidate the important role that contact geometry plays in the performance of carbon…
Most carbon nanotube field-effect transistors (CNTFETs) directly attach metal source/drain contacts to an intrinsic nanotube channel. When the gate oxide thickness is reduced, such transistors display strong ambipolar conduction, even when the Schottky barrier for electrons (or for holes) is zero. The resulting leakage current, which increases exponentially with the drain voltage, constrains the potential applications of such devices. In this paper, we use numerical simulations to show that if CNT based metal-oxide-semiconductor (MOS) FETs can be achieved by using heavily doped CNT sections as…
We demonstrate sensitive and fast electrical measurements of a carbon nanotube mechanical resonator. The nanotube is configured as a single-electron transistor, whose conductance is a sensitive transducer for its own displacement. Using an impedance-matching circuit followed by a cryogenic amplifier, the vibrations can be monitored in real time. The sensitivity of this continuous displacement measurement approaches within a factor 470 of the standard quantum limit.
For carbon nanotube transistors, as for graphene, the electrical contacts are a key factor limiting device performance. We calculate the device characteristics as a function of nanotube diameter and metal workfunction. Although the on-state current varies continuously, the transfer characteristics reveal a relatively abrupt crossover from Schottky to ohmic contacts. We find that typical high-performance devices fall surprisingly close to the crossover. Surprisingly, tunneling plays an important role even in this regime, so that current fails to saturate with gate voltage as was expected due to…
We investigate electronic transport properties of Schottky-barrier field-effect transistors (FET) based on double-walled carbon nanotubes (DWNT) with a semiconducting outer shell and a metallic inner one. These kind of DWNT-FET show asymmetries of the $I$-$V$ characteristics and threshold voltages due to the electron-hole asymmetry of the Schottky barrier. The presence of the metallic inner shell induces a large effective band gap, which is one order of magnitude larger than that due to the semiconducting shell alone of a single-walled carbon nanotube FET.
The influence of defects on electron transport in single-wall carbon nanotube field effect transistors (CNFETs) is probed by combined scanning gate microscopy (SGM) and scanning impedance microscopy (SIM). SGM reveals a localized field effect at discrete defects along the CNFET length. The depletion surface potential of individual defects is quantified from the SGM-imaged radius of the defect as a function of tip bias voltage. This provides a measure of the Fermi level at the defect with zero tip voltage, which is as small as 20 meV for the strongest defects. The effect of defects on transport…
Carbon nanotube field-effect transistors (FETs) with passivated coaxial gate structures have been fabricated after growth of contacted suspended single wall nanotubes (SWNTs) and subsequent coating with gate dielectrics. Electron Fabry-Perot interferences are observed in the FETs indicating ballistic transport in the coated structures. Reliable production of high-performance SWNT FETs has been obtained by combining patterned growth of SWNT arrays with feed-back controlled electrical breakdown to select desired semiconducting SWNTs, making large-scale SWNT FET fabrication achievable. P-type and…
We performed a comprehensive scaling study of Schottky barrier carbon nanotube transistors using self-consistent, atomistic scale simulations. We restrict our attention to Schottky barrier carbon nanotube FETs whose metal source/drain is attached to an intrinsic carbon nanotube channel. Ambipolar conduction is found to be an important factor that must be carefully considered in device design, especially when the gate oxide is thin. The channel length scaling limit imposed by source-drain tunneling is found to be between 5nm and 10nm, depending on the off-current specification. Using a large di…
Single-walled carbon nanotubes (SWNTs) have been grown via chemical vapor deposition on high-kappa dielectric SrTiO3/Si substrates, and high-performance semiconducting SWNT field-effect transistors have been fabricated using the thin SrTiO3 as gate dielectric and Si as gate electrode. The transconductance per channel width is 8900 S/m. The high transconductance cannot be explained by the increased gate capacitance; it is proposed that the increased electric field at the nanotube-electrode interface due to the high-kappa SrTiO3 decreases or eliminates the nanotube-electrode Schottky barrier.
High performance enhancement mode semiconducting carbon nanotube field-effect transistors (CNTFETs) are obtained by combining ohmic metal-tube contacts, high dielectric constant HfO2 films as gate insulators, and electrostatically doped nanotube segments as source/drain electrodes. The combination of these elements affords high ON currents, subthreshold swings of ~ 70-80 mV/decade, and allows for low OFF currents and suppressed ambipolar conduction. The doped source and drain approach resembles that of MOSFETs and can impart excellent OFF states to nanotube FETs under aggressive vertical scali…
We use a simultaneous flow of ethylene and hydrogen gases to grow single wall carbon nanotubes by chemical vapor deposition. Strong coupling to the gate is inferred from transport measurements for both metallic and semiconducting tubes. At low-temperatures, our samples act as single-electron transistors where the transport mechanism is mainly governed by Coulomb blockade. The measurements reveal very rich quantized energy level spectra spanning from valence to conduction band. The Coulomb diamonds have similar addition energies on both sides of the semiconducting gap. Signatures of subbands po…
We report the imaging of magnetic domains in ferromagnetic CoNiB nanotubes with very long aspect ratio, fabricated by electroless plating. While axial magnetization is expected for long tubes made of soft magnetic materials, we evidence series of azimuthal domains. We tentatively explain these by the interplay of anisotropic strain and/or grain size, with magneto-elasticity and/or anisotropic interfacial magnetic anisotropy. This material could be interesting for dense data storage, as well as curvature-induced magnetic phenomena such as the non-reciprocity of spin-wave propagation.
At any metal-carbon nanotube interface there is charge transfer and the induced interfacial field determines the position of the carbon nanotube band structure relative to the metal Fermi-level. In the case of a single-wall carbon nanotube (SWNT) supported on a gold substrate, we show that the charge transfers induce a local electrostatic potential perturbation which gives rise to the observed Fermi-level shift in scanning tunneling spectroscopy (STS) measurements. We also discuss the relevance of this study to recent experiments on carbon nanotube transistors and argue that the Fermi-level al…
High performance p- and n-type single-walled carbon nanotube (SWNT) field-effect transistors (FETs) are obtained by using high and low work function metals, Pd and Al as source/drain (S/D) electrodes respectively. Ohmic contacts made to chemically intrinsic SWNTs, with no or small Schottky barriers (SB), afford high ON-state currents up to 20 uA per tube. The lack of significant Fermi-level pinning at the nanotube-metal interfaces allows for fine-tuning of the barrier heights for p-and n-channel conductions by changing the contact metals. The air-stable p- and n-FETs thus obtained can be used …
The 1/f noise in individual semiconducting carbon nanotubes (s-CNT) in a field effect transistor configuration has been measured in ultra-high vacuum and following exposure to air. The amplitude of the normalized current spectral noise density is independent of source-drain current, indicating the noise is due to mobility rather than number fluctuations. Hooge's constant for s-CNT is found to be 9.3 plus minus 0.4x10^-3. The magnitude of the 1/f noise is substantially degreased by exposing the devices to air.
This work evaluates the performance of carbon nanotube field effect transistors (CNTFET) using few layer graphene as the contact electrode material. We present the experimental results obtained on the barrier height at CNT graphene junction using temperature dependent IV measurements. The estimated barrier height in our devices for both holes and electrons is close to zero or slightly negative indicating the Ohmic contact of graphene with the valence and conduction bands of CNTs. In addition, we also report that there is no correlation between the barrier height and thickness of graphene.
We develop theoretical arguments that demonstrate the possibility of metallic field-effect transistors (METFET's) in one-dimensional systems and particularly in armchair carbon nanotubes. A very inhomogeneous electric field, such as the field of a tunnelling tip, can penetrate the relatively weakly screened nanotubes and open an energy gap. As a consequence, an energy barrier forms that impedes electron flow and thus permits transistor action. This type of metallic field effect is advantageous because of the high conductance of the metallic tubes in the ON--state.
Building smaller transistors with enhanced functionality is critical in extending the limits of Moores law and meeting the demands of the electronics industry. Here we demonstrate transistor operation in a suspended single carbon nanotube (CNT) using feedback-enabled radiation pressure of a near-field focused laser that enabled significant changes in conductivity of the CNT. Further, using in-situ tip-enhanced Raman spectroscopy, we show that the change in conductivity of over five orders in magnitude is accompanied by self-induced defect states within the CNT. The entire structure is less tha…
Single electron transistors (SETs) are fabricated by placing single walled carbon nanotubes (SWNTs) on a 100 nm wide local Al/Al2O3 bottom gate and then contacting with Pd electrodes. Coulomb oscillations up to 125 K were observed and charging energies of 12-15 meV with level spacing of ~5 meV were measured from the Couloumb diamond, in agreement with a dot size of ~100 nm, implying that the local gate defines the dot size by bending SWNT at the edges and controls its operation. This "mechanical template" approach may facilitate large scale fabrication of SET devices using SWNT.
We report on the influence of low gamma irradiation (10^4 Gy) on the noise properties of individual carbon nanotube (CNT) field-effect transistors (FETs) with different gate configurations and two different dielectric layers, SiO2 and Al2O3. Before treatment, strong generation-recombination (GR) noise components are observed. These data are used to identify several charge traps related to dielectric layers of the FETs by determining their activation energy. Investigation of samples with a single SiO2 dielectric layer as well as with two dielectric layers allows us to separate traps for each of…
Electronic transport in a carbon nanotube (CNT) metal-oxide-semiconductor field effect transistor (MOSFET) is simulated using the non-equilibrium Green's functions method with the account of electron-phonon scattering. For MOSFETs, ambipolar conduction is explained via phonon-assisted band-to-band (Landau-Zener) tunneling. In comparison to the ballistic case, we show that the phonon scattering shifts the onset of ambipolar conduction to more positive gate voltage (thereby increasing the off current). It is found that the subthreshold swing in ambipolar conduction can be made as steep as 40mV/d…
We report on microwave operation of top-gated single carbon nanotube transistors. From transmission measurements in the 0.1-1.6 GHz range, we deduce device transconductance gm and gate-nanotube capacitance Cg of micro- and nanometric devices. A large and frequency-independent gm of about 20 microSiemens is observed on short devices, which meets the best dc results. The capacitance per unit gate length of 60 aF/micrometer is typical of top gates on a conventional oxide with a dielectric constant equal to 10. This value is a factor of 3-5 below the nanotube quantum capacitance which, according t…
We use Kelvin Force Microscopy (KFM) to study the electrostatic properties of single-walled Carbon Nanotube Field Effect Transistor devices (CNTFETs) with backgate geometry at room temperature. We show that KFM maps recorded as a function of the device backgate polarization enable a complete phenomenological determination of the averaging effects associated with the KFM probe side capacitances, and thus, to obtain KFM measurements with quantitative character. The value of the electrostatic lever arm of the CNTFET is determined from KFM measurements, and found in agreement with transport measur…
We investigate theoretically the switching characteristics of semiconducting carbon nanotubes connected to gold electrodes under an external (gate) electric field. We find that the external introduction of holes is necessary to account for the experimental observations. We identify metal-induced-gap states (MIGS) at the contacts and find that the MIGS of an undoped tube would not significantly affect the switching behavior, even for very short tube lengths. We also explore the miniaturization limits of nanotube transistors, and, on the basis of their switching ratio, we conclude that transisto…
Recently, Coulomb blockade physics was observed at room temperature in a carbon nanotube single-electron transistor (H. W. Ch. Postma, et. al., Science 293, 76 (2001)). In this work, we suggest that these devices may be promising for studying the Kondo effect. In particular, they could allow for a detailed investigation of the 2-channel Kondo fixed point. Moreover, fabricating a similar device in a short nanotube could be promising for studying the effect of a magnetic impurity in an ultrasmall metallic grain. Experimental signatures of the Kondo effect in these systems is discussed.
We report on a new computational model to efficiently simulate carbon nanotubebased field effect transistors (CNT-FET). In the model, a central region is formed by a semiconducting nanotube that acts as the conducting channel, surrounded by a thin oxide layer and a metal gate electrode. At both ends of the semiconducting channel, two semi-infinite metallic reservoirs act as source and drain contacts. The current-voltage characteristics are computed using the Landauer formalism, including the effect of the Schottky barrier physics. The main operational regimes of the CNT-FET are described, incl…
We have investigated shot noise in a 6-nm-diameter, semiconducting multiwalled carbon nanotube FET at 4.2 K over the frequency range 600 - 950 MHz. We find a transconductance of 3 - 3.5 $μ$S for optimal positive and negative source-drain voltages V. For the gate referred input voltage noise, we obtain 0.2 and 0.3 $μ{V}/ \sqrt{Hz}$ for V>0 and V<0, respectively. As effective charge noise this corresponds to $2-3 \cdot 10^{-5}$ e/$\sqrt{Hz}$.
We explore the electric-field effect of carbon nanotubes (NTs) in electrolytes. Due to the large gate capacitance, Fermi energy shifts of order +/- 1 V can be induced, enabling to tune NTs from p to n-type. Consequently, large resistance changes are measured. At zero gate voltage the NTs are hole doped in air with E_F ? 0.3-0.5 eV, corresponding to a doping level of ? 10^{13} cm^{-2}. Hole-doping increases in the electrolyte. This hole doping (oxidation) is most likely caused by the adsorption of oxygen in air and cations in the electrolyte.
We have investigated radio-frequency single-electron transistor (RF-SET) operation of single-walled carbon nanotube quantum dots in the strong tunneling regime. At 4.2 K and carrier frequency 754.2 MHz, we reach a charge sensitivity of 2.3e-6 e/Hz^(1/2) over a bandwidth of 85 MHz. Our results indicate a gain-bandwidth product of 3.7e13 Hz^(3/2)/e, which is by one order of magnitude better than for typical RF-SETs.
We report an experimental noise study of intermediate sized quasi ballistic semiconducting multiwalled carbon nanotube (IS-MWCNT) devices. The noise is two orders of magnitude lower than in singlewalled nanotubes (SWCNTs) and has no length dependence within the studied range. In these channel limited devices with small or negligible Schottky barriers the noise is shown to originate from the intrinsic potential fluctuations of charge traps in the gate dielectric. The gate dependence of normalized noise can be explained better using ballistic the charge noise model rather than diffusive McWhorte…
Choosing a suitable doping level of channel relevant to channel diameter is considered for determining the carbon nanotube field effect transistors' performance which seem to be the best substitute of current transistor technology. For low diameter values of channel the ratio of on/off current declines by increasing the doping level. But for higher diameter values there is an optimum point of doping level in obtaining the highest on/off current ratio. For further verification, the variations of performance are justified by electron distribution function's changes on energy band diagram of thes…
Band-to-band tunneling (BTBT) devices have recently gained a lot of interest due to their potential for reducing power dissipation in integrated circuits. We have performed extensive simulations for the BTBT operation of carbon nanotube metal-oxide-semiconductor field-effect transistors (CNT-MOSFETs) using the non-equilibrium Green's functions formalism for both ballistic and dissipative quantum transport. In comparison with recently reported experimental data (Y. Lu et al, J. Am. Chem. Soc., v. 128, p. 3518-3519, 2006), we have obtained strong evidence that BTBT in CNT-MOSFETs is dominated by…
We demonstrate the realization of an electrically-driven integrated source of surface plasmon polaritons. Light-emitting individual single-walled carbon nanotube field effect transistors were fabricated in a plasmonic-ready platform. The devices were operated at ambient condition to act as an electroluminescence source localized near the contacting gold electrodes. We show that photon emission from the semiconducting channel can couple to propagating surface plasmons developing in the electrical terminals. Momentum-space spectroscopy suggests that excited plasmon modes are bound to the metal-g…
Junctionless transistors made of silicon have previously been demonstrated experimentally and by simulations. Junctionless devices do not require fabricating an abrupt source-drain junction and thus can be easier to implement in aggressive geometries. In this paper, we explore a similar architecture for aggressively scaled devices with the channel consisting of doped carbon nanotubes (CNTs). Gate all around (GAA) field effect transistor (FET) structures are investigated for n- and p-type doping. Current-voltage characteristics and sub-threshold characteristics for a CNTbased junctionless FET i…
Spectroscopic, time-resolved scanning photocurrent microscopy is shown to distinguish the intrinsic photoresponse of monodisperse semiconducting (99%) single-walled carbon nanotubes (SWCNTs) from the extrinsic photoresponse of the substrate. A persistent positive photocurrent induced by near-IR excitation is attributed to the generation of free carriers by inter-band excitation in SWCNTs. For shorter excitation wavelengths, absorption by the Si substrate generates two types of photocurrent: a transient positive photoresponse, identified as a displacement current, and a persistent negative phot…
We predict shot noise enhancement in defect-free carbon nanotube field-effect transistors through a numerical investigation based on the self-consistent solution of the Poisson and Schrodinger equations within the non-equilibrium Green functions formalism, and on a Monte Carlo approach to reproduce injection statistics. Noise enhancement is due to the correlation between trapping of holes from the drain into quasi-bound states in the channel and thermionic injection of electrons from the source, and can lead to an appreciable Fano factor of 1.22 at room temperature.
