YBCO Transition Edge Sensors Used For Very Low Noise Thermal Control
Bruno Guillet, Didier Robbes, Laurence Mechin
备注:
6 pages, ASC 2002 (Applied Superconductivity Conference), Houston, TX USA (Aout 2002): Oral contribution, to be published in IEEE Trans. Appl. Supercond. June 2003
在电替代辐射计中,要求对温度进行超低噪声控制。在这个框架内,我们提出的结果致力于铜板的温度调节,3厘米直径和1毫米厚,使用YBa 2Cu 3 O 7-d(YBCO)过渡边缘传感器(TES)。其中一个TES用作温度控制单元的主动温度计,而另外两个TES测量板温度行为。两个加热电阻器沿着螺旋图案缠绕,就在铜板下面,以最小化加热延迟。通过第二个分布式电阻施加一个小的热扰动,两个TES之间的相关性被清楚地强调出来,其路径紧密跟随主电阻。在10 mHz的30 microK rms的校准温度振荡与频谱分析一起测量,并实现了在几个microK rms的范围内的温度分辨率。
英文摘要:
In electrically substituted radiometers, the ultra low noise control of the temperature is required. In this framework, we present results dedicated to the temperature regulation of copper plates, 3 cm diameter and 1 mm thick, using YBa2Cu3O7-d (YBCO) transition edge sensors (TES). One of the TES was used as the active thermometer of the temperature control unit, whereas the two others measured the plate temperature behavior. Two heating resistors were wound along a spiral pattern, just underneath the copper plate, to minimize the heating delay. The correlation between the two TES was clearly highlighted by applying a small heat perturbation through the second distributed resistor, the path of which closely follows that of the main resistor. Calibrated temperature oscillations of 30 microK rms at 10mHz together with spectral analysis were measured and a temperature resolution in the range of a few microK rms was achieved.
The role of kinetic inductance on the performance of YBCO SQUID magnetometers
当优化由高温超导体YBa $_2$ Cu $_3$ O $_{7-x}$(YBCO)制成的超导量子干涉器件(SQUID)磁强计的性能时,电感是一个关键参数,因为较低的SQUID电感$L$导致较低的通量噪声,但也导致与拾取回路的较弱耦合。为了优化SQUID的设计,我们结合电感模拟和测量来提取不同的电感贡献,并测量的传递函数$V_Φ$和磁通噪声$S_Φ^{1/2}$对$L$的依赖性。两个样品之间的比较表明,动态电感的贡献随薄膜质量变化很大,因此使电感测量的SQUID表征的一个重要组成部分。由于改进了对动力学电感贡献的估计,可以在很大程度上避免先前发现的$V_Φ$和$S_Φ^{1/2}$的理论估计与测量值之间的差异。然后,我们使用测量结果和改进的理论估计来优化SQUID几何形状,并达到$S_B^{1/2}$ = 44 fT/ $\sqrt{\textrm{Hz}}$的噪声水平,以获得具有8.6 mm $\times$ 9.2 mm直接耦合拾取回路的最佳SQUID磁力计。最后,我们展示了一种可靠的一次性传感器校准方法,该方法在几个开尔文的温度范围内是恒定的,尽管存在温度相关的耦合贡献,如动力学电感。所发现的动态电感贡献的变化不仅对YBCO SQUID磁强计的设计有影响,而且对所有在其临界温度附近工作的基于窄线宽SQUID的器件也有影响。
Microfabricated sensor platform with through-glass vias for bidirectional 3-omega thermal characterization of solid and liquid samples
提出了一种新型的微加工全电测量平台,用于直接、准确和快速地测量液体和固体材料的热导率和扩散率。测量方法基于双向3 Ω方法。该平台是由玻璃基板上的传感器结构和一个非常薄的介电纳米层压钝化层制造。使用玻璃通孔从芯片背面接触传感器,使平台的顶面在3 Ω测量期间不受样品沉积、操作和光学检查的影响。通过原子层沉积在平台表面上的薄钝化层提供了优异的耐化学性,并允许测量导电样品,同时保持简单热分析的条件。我们演示了硼硅酸盐玻璃,纯水,甘油,2-丙醇,PDMS,固化环氧树脂和散热器化合物的热导率的测量。结果与文献值和稳态分杆法获得的值相当。小的样品体积(~0.02 mm $^2$)足以使用该平台进行精确测量,允许快速测量热特性的温度依赖性,这对于许多材料(如液体、凝胶、糊状物和固体)的开发、优化和质量测试非常有用。
Three-Sensor 3ω-2ω Method for the Simultaneous Measurement of Thermal Conductivity and Thermal Boundary Resistance in Film-on-Substrate Heterostructures
Siloxane-based 6LiF composites for flexible thermal neutron scintillation sensors with high efficiency: effects of 6LiF crystals size and dispersion homogeneity